TS27M4AM

TS27M4C,I,M PRECISION LOW POWER CMOS QUAD OPERATIONAL AMPLIFIERS s LOW POWER CONSUMPTION : 150µA/op s OUTPUT VOLTAGE CAN SWING TO GROUND s EXCELLENT PHASE MARGIN ON CAPACITIVE LOADS s STABLE AND LOW OFFSET VOLTAGE s THREE INPUT OFFSET VOLTAGE SELECTIONS DESCRIPTION These devices are low cost, low power quad operational amplifiers designed to operate with single or dual supplies. These operational amplifiers use the ST silicon gate CMOS process allowing an excellent consumption-speed ratio. These series are ideally suited for low consumption applications. Three power consumptions are available allowing to have always the best consumption-speed ratio: N DIP14 (Plastic Package) D SO14 (Plastic Micropackage) P TSSOP14 (Thin Shrink Small Outline Package) u ICC = 10µA/amp.: TS27L4 (very low power) u ICC = 150µA/amp.: TS27M4 (low power) u ICC = 1mA/amp.: TS274 (standard) These CMOS amplifiers offer very high input impedance and extremely low input currents. The major advantage versus JFET devices is the very low input currents drift with temperature (see figure 2). ORDER CODE Package Part Number Temperature Range N TS27M4C/AC/BC 0°C, +70°C TS27M4I/AI/BI -40°C, +125°C TS27M4M/AM/BM -55°C, +125°C Example : TS27M4ACN • • • D • • • P • • • PIN CONNECTIONS (top view) Output 1 1 Inverting Input 1 2 Non-inverting Input 1 3 VCC + 4 Non-inverting Input 2 5 Inverting Input 2 6 Output 2 7 + + + + 14 Output 4 13 Inverting Input 4 12 Non-inverting Input 4 11 VCC 10 Non-inverting Input 3 9 8 Inverting Input 3 Output 3 N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = T hin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT) November 2001 1/9 TS27M4C,I,M BLOCK DIAGRAM VCC Current source xI Input differential Second stage Output stage Output VCC E E ABSOLUTE MAXIMUM RATINGS Symbol VCC Vid Vi Io Iin Toper Tstg + Parameter Supply Voltage 3) 1) 2) TS27M4C/AC/BC TS27M4I/AI/BI TS27M4M/AM/BM 18 ±18 -0.3 to 18 ±30 ±5 Unit V V V mA mA Differential Input Voltage Input Voltage Output Current for VCC+ ≥ 15V Input Current Operating Free-Air Temperature Range Storage Temperature Range 0 to +70 -40 to +125 -65 to +150 -55 to +125 °C °C 1. All values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input and the output voltages must never exceed the magnitude of the positive supply voltage. OPERATING CONDITIONS Symbol VCC+ Vicm Supply Voltage Common Mode Input Voltage Range Parameter Value 3 to 16 0 to VCC+ - 1.5 Unit V V 2/9 VCC T24 T 25 T 26 T6 T8 T27 T5 T 10 T 15 SCHEMATIC DIAGRAM (for 1/4 TS27M4) R2 T 28 T1 Input T 18 T2 Input R1 C1 T11 T 12 T17 T7 T 23 T3 Output T19 T4 T16 T9 T 13 T 14 T20 T 22 T21 T29 VCC TS27M4C,I,M 3/9 TS27M4C,I,M ELECTRICAL CHARACTERISTICS VCC+ = +10V, VCC-= 0V, Tamb = +25°C (unless otherwise specified) TS27M4C/AC/BC Symbol Parameter Min. Input Offset Voltage VO = 1.4V, Vic = 0V Vio Tmin ≤ Tamb ≤ Tmax TS27M4C/I/M TS27M4AC/AI/AM TS27M4B/C/I/M TS27M4C/I/M TS27M4AC/AI/AM TS27M4B/C/I/M Typ. 1.1 0.9 0.25 Max. 10 5 2 12 6.5 3 TS27M4I/AI/BI TS27M4M/AM/BM Min. Typ. Max. 10 5 2 12 6.5 3.5 Unit 1.1 0.9 0.25 mV DVio Iio Input Offset Voltage Drift Input Offset Current note 1) Vic = 5V, VO = 5V Tmin ≤ Tamb ≤ Tmax Input Bias Current - see note 1 Vic = 5V, VO = 5V Tmin ≤ Tamb ≤ Tmax High Level Output Voltage Vid = 100mV, RL = 100lΩ Tmin ≤ Tamb ≤ Tmax Low Level Output Voltage Vid = -100mV Large Signal Voltage Gain ViC = 5V, RL = 100kΩ, Vo = 1V to 6V Tmin ≤ Tamb ≤ Tmax Gain Bandwidth Product Av = 40dB, RL = 100kΩ, CL = 100pF, fin = 100kHz Common Mode Rejection Ratio ViC = 1V to 7.4V, Vo = 1.4V Supply Voltage Rejection Ratio VCC+ = 5V to 10V, Vo = 1.4V Supply Current (per amplifier) Av = 1, no load, Vo = 5V Tmin ≤ Tamb ≤ Tmax Output Short Circuit Current Vo = 0V, Vid = 100mV Output Sink Current Vo = VCC, Vid = -100mV Slew Rate at Unity Gain RL = 100kΩ, CL = 100pF, Vi = 3 to 7V Phase Margin at Unity Gain Av = 40dB, RL = 100kΩ, CL = 100pF Overshoot Factor Equivalent Input Noise Voltage f = 1kHz, Rs = 100Ω Channel Separation 65 60 30 20 8.7 8.6 2 1 100 1 150 8.9 8.7 8.5 50 50 30 10 2 1 200 1 300 8.9 µV/°C pA Iib pA VOH VOL Avd V 50 50 mV V/mV GBP CMR SVR 1 80 80 150 200 250 65 60 1 80 80 150 200 300 MHz dB dB ICC Io Isink SR φm KOV en Vo1/Vo2 1. µA 60 45 0.6 45 30 38 120 60 45 0.6 45 30 38 120 mA mA V/µs Degrees % nV ----------Hz dB Maximum values including unavoidable inaccuracies of the industrial test. 4/9 TS27M4C,I,M TYPICAL CHARACTERISTICS Figure 1 : Supply Current (each amplifier) versus Supply Voltage 200 OUTPUT VOLTAGE, VOH (V) SUPPLY CURRENT, I CC (µA) TAMB = 25 ˚C AV= 1 VO = V / 2 CC Figure 3b : High Level Output Voltage versus High Level Output Current 20 16 12 8 4 0 -50 VCC = 10V TAMB = 25˚ C V ID = 100mV VCC = 16V 150 100 50 0 4 8 12 16 -40 -30 -20 -10 0 SUPPLY VOLTAGE, V CC (V) OUTPUT CURRENT, I OH (mA) Figure 2 : Input Bias Current versus Free Air Temperature 100 INPUT BIAS CURRENT, IIB (pA) Figure 4a : Low Level Output Voltage versus Low Level Output Current 1.0 OUTPUT VOLTAGE, VOL (V) VCC = 10V V i = 5V VCC = 3V 0.8 VCC = 5V 0.6 0.4 0.2 TAMB = 25 ˚C V i = 0.5V VID = -1V 10 1 25 50 75 100 125 TEMPERATURE, TAMB (˚C) 0 1 2 3 OUTPUT CURRENT, I OL (mA) Figure 3a : High Level Output Voltage versus High Level Output Current 5 4 3 2 1 0 VCC = 3V Figure 4b : Low Level Output Voltage versus Low Level Output Current 3 OUTPUT VOLTAGE, VOL (V) OUTPUT VOLTAGE, VOH (V) TAMB = 25˚ C V ID = 100mV VCC = 5V VCC = 10V 2 VCC = 16V 1 TAMB = 25 ˚C V i = 0.5V VID = -1V -10 -8 -6 -4 -2 0 0 4 8 12 16 20 OUTPUT CURRENT, I OH (mA) OUTPUT CURRENT, I OL (mA) 5/9 TS27M4C,I,M Figure 5 : Open Loop Frequency Response and Phase Shift Figure 8 : Phase Margin versus Capacitive Load (Degrees) 50 40 GAIN (dB) 30 20 10 0 -10 2 10 PHASE Tamb = 25˚C VCC+ = 10V R L = 100k Ω C L = 100pF A VCL = 100 10 3 4 80 PHASE (Degrees) GAIN Phase Margin 0 45 90 135 70 T amb = 25˚C R L = 100kΩ AV=1 VCC = 10V PHASE MARGIN, φm 60 Gain Bandwidth Product 6 50 180 7 10 10 5 10 FREQUENCY, f (Hz) 10 40 0 20 40 60 80 CAPACITANCE, C L (pF) 100 Figure 6 : Gain Bandwidth Product versus Supply Voltage Figure 9 : Slew Rate versus Supply Voltage GAIN BANDW. PROD., GBP (kHz) 1400 1000 600 200 0 Tamb = 25˚C R L = 100kΩ C L = 100pF AV = 1 SLEW RATES, SR (V/ µs) 1800 0.9 0.8 0.7 0.6 0.5 0.4 4 6 8 10 12 14 SUPPLY VOLTAGE, V CC (V) 16 SR T amb = 25˚C R L = 100kΩ C L = 100pF SR 4 8 12 16 SUPPLY VOLTAGE, V CC (V) Figure 7 : Phase Margin versus Supply Voltage Figure 10 : Input Voltage Noise versus Frequency PHASE MARGIN, φm (Degrees) EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz) 50 300 VCC = 10V Tamb = 25˚C 200 R S = 100 Ω 40 Tamb = 25˚C R L = 100kΩ C L = 100pF AV = 1 0 4 8 12 SUPPLY VOLTAGE, V CC (V) 16 30 100 20 0 1 100 10 FREQUENCY (Hz) 1000 6/9 TS27M4C,I,M PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP Millimeters Dim. Min. a1 B b b1 D E e e3 F i L Z 0.51 1.39 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 Typ. Max. 1.65 Min. 0.020 0.055 Inches Typ. Max. 0.065 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100 7/9 TS27M4C,I,M PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO) L C G c1 a2 b e3 D M e A s E 14 1 8 7 F Millimeters Dim. Min. A a1 a2 b b1 C c1 D (1) E e e3 F (1) G L M S 0.1 0.35 0.19 0.5 45° (typ.) 8.55 5.8 1.27 7.62 3.8 4.6 0.5 4.0 5.3 1.27 0.68 8° (max.) 0.150 0.181 0.020 8.75 6.2 0.336 0.228 Typ. Max. 1.75 0.2 1.6 0.46 0.25 Min. 0.004 0.014 0.007 a1 b1 Inches Typ. Max. 0.069 0.008 0.063 0.018 0.010 0.020 0.344 0.244 0.050 0.300 0.157 0.208 0.050 0.027 Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK. 8/9 TS27M4C,I,M PACKAGE MECHANICAL DATA 14 PINS - THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP) c 0,25 mm .010 inch GAGE PLANE k L E1 SEATING PLANE C A A2 A1 E b 8 7 D aaa C 14 1 PIN 1 IDENTIFICATION Millimeters Dim. Min. A A1 A2 b c D E E1 e k l 0.05 0.80 0.19 0.09 4.90 4.30 0° 0.50 Typ. Max. 1.20 0.15 1.05 0.30 0.20 5.10 4.50 8° 0.75 Min. 0.01 0.031 0.007 0.003 0.192 0.169 0° 0.09 e L1 Inches Typ. Max. 0.05 0.006 0.041 0.15 0.012 0.20 0.177 8° 0.030 1.00 0.039 5.00 6.40 4.40 0.65 0.60 0.196 0.252 0.173 0.025 0.0236 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States © http://www.st.com 9/9