TS3021ICT

TS3021, TS3021A Datasheet Rail-to-rail 1.8 V high-speed comparator Features SOT23-5/SC70-5 Pin connections (top view) OUT 1 Vcc- 2 IN+ 3 5 + Vcc+ 4 IN- • • • • • • • • • Propagation delay: 38 ns Low current consumption: 73 µA Rail-to-rail inputs Push-pull outputs Supply operation from 1.8 to 5 V Wide temperature range: -40 °C to 125 °C High ESD tolerance: 5 kV HBM, 300 V MM SMD packages Automotive qualification Applications Maturity status link TS3021, TS3021A Related products TS3022 For a dual comparator with similar performances TS3011 For a high-speed comparator • • • • • Telecom Instrumentation Signal conditioning High-speed sampling systems Portable communication systems Description The TS3021, TS3021A single comparator features high-speed response time with rail-to-rail inputs. With a supply voltage specified from 2 to 5 V, this comparator can operate over a wide temperature range: -40 °C to 125 °C. The TS3021, TS3021A comparator offers micropower consumption as low as a few tens of microamperes thus providing an excellent ratio of power consumption current versus response time. The TS3021, TS3021A includes push-pull outputs and is available in small packages (SOT23-5 and SC70-5). DS4807 - Rev 9 - October 2022 For further information contact your local STMicroelectronics sales office. www.st.com TS3021, TS3021A Absolute maximum ratings and operating conditions 1 Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings (AMR) Symbol Parameter Value VCC Supply voltage, VCC = (VCC+) - (VCC-)(1) 5.5 VID Differential input voltage (2) ±5 Input voltage range Rthja Thermal resistance junction-to-ambient (3) SOT23-5 250 SC70-5 205 SOT23-5 81 SC70-5 172 Rthjc Thermal resistance junction-to-case Tstg Storage temperature -65 to 150 Tj Junction temperature 150 Lead temperature (soldering 10 s) 260 HBM: human body model (4) 5000 ESD MM: machine model V (VCC-) - 0.3 to (VCC+) + 0.3 VIN TLEAD Unit (3) (5) 300 CDM: charged device model (6) °C/W °C V 1500 1. All voltage values, except the differential voltage are referenced to (VCC-) 2. The magnitude of the input and output voltages must never exceed the supply rail ±0.3 V 3. Short circuits can cause excessive heating. These values are typical 4. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating. 5. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of connected pin combinations while the other pins are floating. 6. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly to the ground through only one pin. This is done for all pins. Table 2. Operating conditions Symbol VCC DS4807 - Rev 9 Parameter Supply voltage Vicm Common mode input voltage range Toper Operating temperature range Value 0 °C < Tamb < 125 °C Unit 1.8 to 5 -40 °C < Tamb < 125°C 2 to 5 -40 °C < Tamb < 85 °C (VCC- ) - 0.2 to (VCC+) + 0.2 85 °C < Tamb < 125 °C (VCC- ) to (VCC+) -40 to 125 V °C page 2/16 TS3021, TS3021A Electrical characteristics 2 Electrical characteristics Table 3. Electrical characteristics at VCC = 2 V, Tamb = 25 ° C, and full Vicm range (unless otherwise specified) Symbol VIO ΔVio/ΔT IIO IIB Test conditions (1) Parameter Input offset voltage Input offset voltage drift Input offset current (2) Input bias current (2) Min. Typ. Max. TS3021A 0.5 2 TS3021 0.5 6 -40 °C < Tamb < 125 °C, TS3021A 4 -40 °C < Tamb < 125 °C, TS3021 7 -40 °C < Tamb < 125 °C 3 20 Tamb 1 20 -40 °C < Tamb < 125 °C 100 Tamb 86 -40 °C < Tamb < 125 °C 73 No load, output high, Vicm = 0 V, Supply current No load, output low, Vicm = 0 V 84 VOH Output voltage high VOL Output voltage low Source 9 Sink 10 Isource = 1 mA 1.88 -40 °C < Tamb < 125 °C 1.80 Isink = 1 mA Common mode rejection ratio 0 < Vicm < 2 V SVR Supply voltage rejection ∆Vcc = 2 to 5 V TPLH Propagation delay, low to high output level (3) TPHL Propagation delay, high to low output level (4) 90 105 µA mA 1.92 60 -40 °C < Tamb < 125 °C CMRR nA 125 -40 °C < Tamb < 125 °C Short-circuit current µV/°C 115 -40 °C < Tamb < 125 °C No load, output low, Vicm = 0 V, ISC mV 300 No load, output high, Vicm = 0 V ICC 160 Unit V 100 150 67 58 mV dB 73 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 100 mV 38 60 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 20 mV 48 75 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 100 mV 40 60 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 20 mV 49 75 ns TF Fall time f = 10 kHz, CL = 50 pF, RL = 10 kΩ, overdrive = 100 mV 8 TR Rise time f = 10 kHz, CL = 50 pF, RL = 10 kΩ, overdrive = 100 mV 9 1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed at the temperature range limits 2. Maximum values include unavoidable inaccuracies of the industrial tests 3. Response time is measured 10%/90% of the final output value with the following conditions: inverting input voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm - 100 mV to Vicm + overdrive. 4. Response time is measured 10%/90% of the final output value with the following conditions: Inverting input voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm + 100 mV to Vicm - overdrive. DS4807 - Rev 9 page 3/16 TS3021, TS3021A Electrical characteristics Table 4. Electrical characteristics at VCC = 3.3 V, Tamb = 25 ° C, and full Vicm range (unless otherwise specified) Symbol VIO ΔVio/ΔT IIO IIB Test conditions (1) Parameter Input offset voltage Input offset voltage drift Input offset current (2) Input bias current (2) Min. Typ. Max. TS3021A 0.5 2 TS3021 0.5 6 -40 °C < Tamb < 125 °C, TS3021A 4 -40 °C < Tamb < 125 °C, TS3021 7 -40 °C < Tamb < 125 °C 3 20 Tamb 1 20 -40 °C < Tamb < 125 °C 100 Tamb 86 -40 °C < Tamb < 125 °C 75 No load, output high, Vicm = 0 V, Supply current No load, output low, Vicm = 0 V 86 VOH Output voltage high VOL Output voltage low Source 26 Sink 24 Isource = 1 mA 3.20 -40 °C < Tamb < 125 °C 3.10 Isink = 1 mA Common mode rejection ratio 0 < Vicm < 3.3 V SVR Supply voltage rejection ∆Vcc = 2 to 5 V TPLH Propagation delay, low to high output level (3) TPHL Propagation delay, high to low output level (4) 90 110 µA mA 3.25 40 -40 °C < Tamb < 125 °C CMRR nA 125 -40 °C < Tamb < 125 °C Short-circuit current µV/°C 120 -40 °C < Tamb < 125 °C No load, output low, Vicm = 0 V, ISC mV 300 No load, output high, Vicm = 0 V ICC 160 Unit V 80 150 75 58 mV dB 73 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 100 mV 39 65 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 20 mV 50 85 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 100 mV 41 65 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 20 mV 51 80 ns TF Fall time f = 10 kHz, CL = 50 pF, RL = 10 kΩ, overdrive = 100 mV 5 TR Rise time f = 10 kHz, CL = 50 pF, RL = 10 kΩ, overdrive = 100 mV 7 1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed at the temperature range limits 2. Maximum values include unavoidable inaccuracies of the industrial tests 3. Response time is measured 10%/90% of the final output value with the following conditions: inverting input voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm - 100 mV to Vicm + overdrive. 4. Response time is measured 10%/90% of the final output value with the following conditions: Inverting input voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm + 100 mV to Vicm - overdrive. DS4807 - Rev 9 page 4/16 TS3021, TS3021A Electrical characteristics Table 5. Electrical characteristics at VCC = 5 V, Tamb = 25 ° C, and full Vicm range (unless otherwise specified) Symbol VIO ΔVio/ΔT IIO IIB Test conditions (1) Parameter Input offset voltage Input offset voltage drift Input offset current (2) Input bias current (2) Min. Typ. Max. TS3021A 0.5 2 TS3021 0.5 6 -40 °C < Tamb < 125 °C, TS3021A 4 -40 °C < Tamb < 125 °C, TS3021 7 -40 °C < Tamb < 125 °C 3 20 Tamb 1 20 -40 °C < Tamb < 125 °C 100 Tamb 86 -40 °C < Tamb < 125 °C 77 No load, output high, Vicm = 0 V, Supply current No load, output low, Vicm = 0 V 89 VOH Output voltage high VOL Output voltage low Source 51 Sink 40 Isource = 4 mA 4.80 -40 °C < Tamb < 125 °C 4.70 Isink = 4 mA Common mode rejection ratio 0 < Vicm < 5 V SVR Supply voltage rejection ∆Vcc = 2 to 5 V TPLH Propagation delay, low to high output level (3) TPHL Propagation delay, high to low output level (4) 95 115 µA mA 4.84 130 -40 °C < Tamb < 125 °C CMRR nA 135 -40 °C < Tamb < 125 °C Short-circuit current µV/°C 125 -40 °C < Tamb < 125 °C No load, output low, Vicm = 0 V, ISC mV 300 No load, output high, Vicm = 0 V ICC 160 Unit V 180 250 79 58 mV dB 73 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 100 mV 42 75 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 20 mV 54 105 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 100 mV 45 75 Vicm = 0 V, f = 10 kHz, CL = 50 pF, overdrive = 20 mV 55 95 ns TF Fall time f = 10 kHz, CL = 50 pF, RL = 10 kΩ, overdrive = 100 mV 4 TR Rise time f = 10 kHz, CL = 50 pF, RL = 10 kΩ, overdrive = 100 mV 4 1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed at the temperature range limits 2. Maximum values include unavoidable inaccuracies of the industrial tests 3. Response time is measured 10%/90% of the final output value with the following conditions: inverting input voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm - 100 mV to Vicm + overdrive. 4. Response time is measured 10%/90% of the final output value with the following conditions: Inverting input voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm + 100 mV to Vicm - overdrive. DS4807 - Rev 9 page 5/16 TS3021, TS3021A Electrical characteristic curves 3 Electrical characteristic curves Figure 1. Current consumption vs. supply voltage (Vicm = 0 V, output high) 115 VICM= 0V output HIGH 84 Figure 2. Current consumption vs. supply voltage (Vicm = Vcc output high) -40oC 80 110 72 ICC (µ A) ICC (µA) -40oC 105 76 +25oC +125oC 68 100 +25oC 95 64 +125oC 90 60 1.8 2.2 2.6 3.0 3.4 VCC(V) 3.8 4.2 4.6 85 1.8 5.0 Figure 3. Current consumption vs. supply voltage (Vicm = 0 V, output low) VICM= 0V output LOW 96 2.2 2.6 100 VICM=VCC output LOW 3.4 3.8 VCC(V) 4.2 4.6 5.0 -40oC 96 92 -40oC 92 ICC (µ A) 88 3.0 Figure 4. Current consumption vs. supply voltage (Vicm = Vcc output low) 104 100 ICC (µ A) VICM=VCC output HIGH o +25 C 84 +25oC 88 84 80 80 76 +125oC 72 1.8 2.2 2.6 3.0 3.4 3.8 VCC(V) +125oC 76 4.2 4.6 1.8 5.0 Figure 5. Output voltage vs. source current, Vcc = 2 V 2.2 2.6 3.0 3.4 3.8 VCC(V) 4.2 4.6 5.0 Figure 6. Output voltage vs. sink current, Vcc = 2 V 2.0 0.5 1.9 0.4 -40oC 1.7 1.6 o +25 C 1.5 1.4 1.3 0.0 DS4807 - Rev 9 VOUT (V) VOUT (V) 1.8 1.5 2.0 2.5 3.0 ISOURCE (mA) 0.3 +25oC -40oC 0.1 VCC= 2V output HIGH 1.0 +125oC 0.2 +125oC 0.5 VCC= 2V output LOW 3.5 4.0 4.5 5.0 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 ISINK(mA) 3.5 4.0 4.5 5.0 page 6/16 TS3021, TS3021A Electrical characteristic curves Figure 7. Output voltage vs. source current, Vcc = 3.3 V Figure 8. Output voltage vs. sink current, Vcc = 3.3 V 3.30 0.30 3.25 0.20 3.15 VOUT (V) VOUT (V) 3.20 3.10 o +25 C 3.05 2.95 0.0 0.5 1.0 1.5 0.15 +25oC 2.0 2.5 3.0 ISOURCE (mA) 3.5 -40oC 0.05 4.0 4.5 0.00 0.0 5.0 Figure 9. Output voltage vs. source current, Vcc = 5 V 0.25 4.95 0.20 -40oC VOUT (V) 4.90 +25oC 0.5 1.0 1.5 2.0 2.5 3.0 ISINK(mA) 3.5 4.0 4.5 5.0 Figure 10. Output voltage vs. sink current, Vcc = 5 V 5.00 4.85 +125oC 0.10 +125oC VCC= 3.3V output HIGH 3.00 VOUT (V) VCC= 3.3V output LOW 0.25 -40oC VCC= 5V output LOW +125oC 0.15 +25oC 0.10 -40oC 4.80 0.05 VCC= 5V output HIGH 4.75 0.0 0.5 1.0 +125oC 1.5 2.0 2.5 3.0 ISOURCE (mA) 3.5 4.0 4.5 0.00 0.0 5.0 Figure 11. Input offset voltage vs. temperature and common mode voltage 100 VCC = 5V 50 0 VVICM= 0V 0.8 0.6 VICM= 5V 0.4 0.2 0.0 -60 DS4807 - Rev 9 1.5 2.0 2.5 3.0 ISINK(mA) 3.5 4.0 4.5 5.0 VCC= 5V VICM= 0V IIN-125oC IIN+125oC -50 IIB(nA) Vio (mV) 1.0 1.0 Figure 12. Input bias current vs. temperature and input voltage 1.4 1.2 0.5 -100 -150 IIN- 25oC IIN+25oC -200 -250 IIN--40oC IIN+-40oC -300 -40 -20 0 20 40 60 80 Temperature (°C) 100 120 140 -350 -100 -80 -60 -40 -20 0 20 40 60 80 100 VIN(mV) page 7/16 TS3021, TS3021A Electrical characteristic curves Figure 13. Current consumption vs. commutation frequency Figure 14. Propagation delay (HL) vs. overdrive at Vcc = 2 V, Vicm = 0 V 100 600 90 ICC (µA) VCC= 2V 200 T= 125oC TPHL 70 VCC= 3.3V 300 VCC= 2V VICM= 0V TPHL 80 VCC= 5V 400 TP(nS) 500 VICM= 0V CLOAD= 50pF TPHL T= 25oC T= -40oC 60 50 40 100 30 0 10k 100k 20 1M Frequency (Hz) Figure 15. Propagation delay (HL) vs. overdrive at Vcc = 2 V, Vicm = Vcc 70 T= 125oC TPHL T= 25oC T= -40oC 50 30 20 30 40 50 60 70 VOV(mV) 80 100 TPLH 80 o T= 125 C 70 20 90 100 110 TPLH TPLH T= 25oC o 60 T= -40 C 50 TPLH TPLH T= -40oC 0 10 20 30 40 50 60 70 VOV(mV) 80 90 100 110 VCC= 3.3V VICM= 0V 100 90 TPHL 80 T= 125oC TPHL TPHL T= 25oC 70 T= -40oC 60 50 40 40 30 30 20 VCC= 2V VICM= 0V Figure 18. Propagation delay (HL) vs. overdrive at Vcc = 3.3 V, Vicm = 0 V VCC= 2V VICM= VCC 90 90 100 110 50 30 10 80 T= 25oC 60 40 0 50 60 70 VOV(mV) T= 125oC 70 40 Figure 17. Propagation delay (LH) vs. overdrive at Vcc = 2 V, Vicm = Vcc TP (nS) TP (nS) TPHL 40 TPLH 80 60 20 30 90 TP (nS) TP (nS) TPHL 20 100 VCC= 2V VICM= VCC 80 10 Figure 16. Propagation delay (LH) vs. overdrive at Vcc = 2 V, Vicm = 0 V 100 90 0 0 DS4807 - Rev 9 10 20 30 40 50 60 70 VOV(mV) 80 90 100 110 20 0 10 20 30 40 50 60 70 VOV(mV) 80 90 100 110 page 8/16 TS3021, TS3021A Electrical characteristic curves Figure 19. Propagation delay (HL) vs. overdrive at Vcc = 3.3 V, Vicm = Vcc 100 TPHL 100 TPHL o T= 25 C T= -40oC 50 TPLH T = 25oC 70 T = -40oC 60 30 10 20 30 40 50 60 70 VOV(mV) 80 100 TPLH T = 125oC 70 TPLH TPLH T = 25oC T = -40oC 60 50 0 10 20 30 40 50 60 70 VOV(mV) 80 90 100 110 Figure 22. Propagation delay (HL) vs. overdrive at Vcc = 5 V, Vicm = 0 V 110 VCC= 3.3V VICM= VCC 90 80 20 90 100 110 100 VCC= 5V VICM= 0V TPHL 90 T= 125oC TPHL 80 TP (nS) 0 Figure 21. Propagation delay (LH) vs. overdrive at Vcc = 3.3 V, Vicm = Vcc TPHL T= 25oC T= -40oC 70 60 50 40 40 30 30 0 10 20 30 40 50 60 70 VOV(mV) 80 90 100 110 Figure 23. Propagation delay (HL) vs. overdrive at Vcc = 5 V, Vicm = Vcc 110 90 TPHL 80 T= 125oC 0 10 20 o T= 25 C 70 90 T= -40oC 80 50 50 60 70 VOV(mV) 80 90 100 110 VCC= 5V VICM= 0V 110 TPHL 60 40 120 100 TPHL 30 Figure 24. Propagation delay (LH) vs. overdrive at Vcc = 5 V, Vicm = 0 V VCC= 5V VICM= VCC 100 TPLH T = 125oC TPLH TPLH T = 25oC 70 T = -40oC 60 50 40 40 30 20 20 TP (nS) TP (nS) 80 40 30 TP (nS) TPLH T = 125oC 50 40 20 TPLH 90 TPHL 60 20 VCC= 3.3V VICM= 0V 110 TP(nS) T= 125oC 70 TP(nS) 120 VCC= 3.3V VICM= VCC 90 80 Figure 20. Propagation delay (LH) vs. overdrive at Vcc = 3.3 V, Vicm = 0 V 30 0 DS4807 - Rev 9 10 20 30 40 50 60 70 VOV(mV) 80 90 100 110 20 0 10 20 30 40 50 60 70 VOV(mV) 80 90 100 110 page 9/16 TS3021, TS3021A Electrical characteristic curves Figure 25. Propagation delay (LH) vs. overdrive at Vcc = 5 V, Vicm = Vcc 100 TPLH T = 125oC 70 VCC= 5V VOV = 100mV 60 55 TPLH TPLH T = 25oC TP (nS) TP (nS) 65 VCC= 5V VICM= VCC 90 80 Figure 26. Propagation delay vs. temperature, Vcc = 5 V, overdrive = 100 mV T = -40oC 60 50 50 45 40 40 30 35 TPLH VVICM= 0V 30 -40 -20 20 0 10 20 30 40 50 60 70 VOV(mV) 80 90 100 110 0 TPHL VICM= 0V TPLH VICM= 5V 20 40 60 Temperature (°C) 80 TPHL VICM= 5V 100 120 Figure 27. Propagation delay vs. common mode voltage, Vcc = 5 V 70 TP (nS) 60 TPLH VOV= 20mV TPHL VOV= 20mV 50 40 30 TPLH VOV= 100mV TPHL VOV= 100mV VCC = 5V Temp.= 25°C 20 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VICM(mV) DS4807 - Rev 9 page 10/16 TS3021, TS3021A Package information 4 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. DS4807 - Rev 9 page 11/16 TS3021, TS3021A SOT23-5 package information 4.1 SOT23-5 package information Figure 28. SOT23-5 package outline Table 6. SOT23-5 mechanical data Dimensions Millimeters Ref. A Min. Typ. Max. Min. Typ. Max. 0.90 1.20 1.45 0.035 0.047 0.057 A1 DS4807 - Rev 9 Inches 0.15 0.006 A2 0.90 1.05 1.30 0.035 0.041 0.051 B 0.35 0.40 0.50 0.014 0.016 0.020 C 0.09 0.15 0.20 0.004 0.006 0.008 D 2.80 2.90 3.00 0.110 0.114 0.118 D1 1.90 0.075 e 0.95 0.037 E 2.60 2.80 3.00 0.102 0.110 0.118 F 1.50 1.60 1.75 0.059 0.063 0.069 L 0.10 0.35 0.60 0.004 0.014 0.024 K 0 degrees 10 degrees 0 degrees 10 degrees page 12/16 TS3021, TS3021A SC70-5 (or SOT323-5) package information 4.2 SC70-5 (or SOT323-5) package information Figure 29. SC70-5 (or SOT323-5) package outline SIDE VIEW DIMENSIONS IN MM GAUGE PLANE COPLANAR LEADS SEATING PLANE TOP VIEW Table 7. SC70-5 (or SOT323-5) mechanical data Dimensions Millimeters Ref. Min. A Typ. 0.80 A1 DS4807 - Rev 9 Inches Max. Min. 1.10 0.032 Typ. 0.043 0.10 A2 0.80 b 0.90 Max. 0.004 1.00 0.032 0.035 0.15 0.30 0.006 0.012 c 0.10 0.22 0.004 0.009 D 1.80 2.00 2.20 0.071 0.079 0.087 E 1.80 2.10 2.40 0.071 0.083 0.094 E1 1.15 1.25 1.35 0.045 0.049 0.053 e 0.65 0.025 e1 1.30 0.051 L 0.26 < 0° 0.36 0.46 0.010 8° 0° 0.014 0.039 0.018 8° page 13/16 TS3021, TS3021A Ordering information 5 Ordering information Table 8. Order codes Order code Temperature range TS3021ILT TS3021IYCT (1) TS3021AILT Packaging -40 to 125 °C SC70-5 SOT23-5 Marking K520 SOT23-5 TS3021IYLT (1) TS3021ICT Package K529 Tape and reel K52 K5S K522 1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 and Q 002 or equivalent DS4807 - Rev 9 page 14/16 TS3021, TS3021A Revision history Table 9. Document revision history Date Revision 01-Jun-2006 1 Changes Initial release Dual version added 01-Sep-2006 2 Pinout of single TS3021 corrected Modified temperature range for input common mode voltage 22-Feb-2007 3 17-Oct-2007 4 Addition of MiniSO-8 package for dual version Marking corrected for SO-8 package Thermal resistance values corrected in AMR table Notes on ESD added in AMR table Dual version (TS3022) removed ESD tolerance modified in Table 1: Absolute maximum ratings Made the following changes in Table 3: – modified Vio typical value and maximum limits – modified Iib typical value 04-Dec-2008 5 – modified Icc typical values and corrected maximum limits – modified Isc typical values – modified Voh and Vol typical values – modified CMRR and SVR typical values – modified TPhl and TPlh typical values All curves modified Features: added “automotive qualification”; added Related products. Table 1 and Table 2: Vdd and Vcc replaced by (Vcc-) and (Vcc+) respectively. 03-Jan-2013 6 Table 3, Table 4, and Table 5: replaced ∆Vio symbol with ∆Vio/∆T. Table 6 and Table 7: minor update (added angle dimensions to “inches” columns). Table 8: added automotive order code Table 3, Table 4, and Table 5: updated Vio parameter 02-Jun-2015 7 Table 6: small "rounding-off modifications to inches parameter Table 8: added order code TS3021AILT Added new part number TS3021A 07-Jul-2016 8 Updated document layout Table 3, Table 4, and Table 5: updated VIO test conditions and values. 17-Oct-2022 DS4807 - Rev 9 9 Added new TS3021IYCT order code in Table 8. Order codes page 15/16 TS3021, TS3021A IMPORTANT NOTICE – READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2022 STMicroelectronics – All rights reserved DS4807 - Rev 9 page 16/16