TS321AILT

TS321 Low-power single operational amplifier Datasheet - production data Description The TS321 device is intended for cost-sensitive applications where space-saving is of great importance. This bipolar operational amplifier (op amp) offers the benefits of a reduced component size (SOT23-5 package) with specifications that match (or are better than) industry standard devices (such as the popular LM358A, LM324, and other similar devices). The TS321 device has an input common mode range (Vicm) that includes ground and therefore can be employed in single supply applications. SOT23-5 (plastic package) Pin connections (top view) Features • • • • • • Large output voltage swing − 0 to 3.5 V min (VCC = 5 V) Low supply current: 500 µA Low input bias current: 20 nA Low input offset voltage − 2 mV max. for TS321A − 4 mV max. for TS321 Wide power supply range − Single supply: 3 to 30 V − Dual supplies: ±1.5 to ±15 V Stable with high capacitive loads November 2014 DocID6298 Rev 9 This is information on a product in full production. 1/15 www.st.com Contents TS321 Contents 1 Schematic diagram.......................................................................... 3 2 Absolute maximum ratings and operating conditions ................. 4 3 4 Electrical characteristics ................................................................ 5 Macromodel ..................................................................................... 8 5 4.1 Important note concerning this macromodel ..................................... 8 4.2 Macromodel code.............................................................................. 8 4.3 Electrical characteristics of the macromodel ................................... 10 Package information ..................................................................... 11 5.1 SOT23-5 package information ........................................................ 12 6 Ordering information..................................................................... 13 7 Revision history ............................................................................ 14 2/15 DocID6298 Rev 9 TS321 1 Schematic diagram Schematic diagram Figure 1: Schematic diagram t DocID6298 Rev 9 3/15 Absolute maximum ratings and operating conditions 2 TS321 Absolute maximum ratings and operating conditions Table 1: Absolute maximum ratings Symbol + VCC Parameter Value Supply voltage ±16 to 32 Vin Input voltage -0.3 to 32 Vid Differential input voltage Tstg Tj Rthja Rthjc Input current (1) Infinite (2) 50 Storage temperature range Thermal resistance junction-to-case °C 150 Thermal resistance junction-to-ambient MM: machine model mA -65 to 150 Maximum junction temperature HBM: human body model ESD V ±32 Output short-circuit duration Iin Unit (3) (3) 250 °C/W 81 (4) 500 (5) 200 CDM: charged device model (6) V 1000 Notes: (1) Short-circuits from the output to VCC can cause excessive heating if VCC > 15 V. The maximum output current is approximately 40 mA independent of the magnitude of VCC. (2) This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistor becoming forward biased and thereby acting as input diodes clamps. In addition to this diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the op amp to go to the VCC voltage level (or to ground for a large overdrive) for the time during which an input is driven negative. This is not destructive and normal output is restored when the input voltage goes back above -0.3 V. (3) Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuits on all amplifiers. All values are typical. (4) Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating. (5) Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of connected pin combinations while the other pins are floating. (6) Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly to ground through only one pin. This is done for all pins. Table 2: Operating conditions Symbol 4/15 Parameter + VCC Supply voltage Vicm Input common mode voltage range + (VCC = 30 V) Toper Operating free air temperature range Value Unit 3 to 30 DocID6298 Rev 9 Tamb = 25 °C Tmin ≤ Tamb ≤ Tmax + 0 to (VCC ) - 1.5 0 to + (VCC ) V -2 -40 to 125 °C TS321 3 Electrical characteristics Electrical characteristics + - Table 3: Electrical characteristics at VCC = 5 V, VCC = ground, Vo = 1.4 V, Tamb = 25 °C (unless otherwise specified) Symbol Parameter Test conditions Min. TS321 Vio Iio Iib Input offset voltage (1) Input offset current Input bias current SVR Supply voltage rejection ratio 5 Tmin ≤ Tamb ≤ Tmax, TS321A 3 2 Tmin ≤ Tamb ≤ Tmax 20 Tmin ≤ Tamb ≤ Tmax 50 Tmin ≤ Tamb ≤ Tmax, VCC = 15 V, RL = 2 kΩ, Vo = 1.4 to 11.4 V 25 Rs ≤ 10 kΩ, VCC = 5 to 30 V 65 + = 30 V Tmin ≤ Tamb ≤ Tmax, VCC = 5 V + CMR Common mode rejection ratio Rs ≤ 10 kΩ Isource Output current source Vid = 1 V, VCC = 15 V, Vo = 2 V Io Short-circuit to ground nA V/mV + 110 + 800 600 900 600 900 65 85 dB 20 40 mA mA Vid = -1 V, = 15 V, Vo = 2 V 10 20 Vid = -1 V, + VCC = 15 V, Vo = 0.2 V 12 50 + VCC = 15 40 + Tmin ≤ Tamb ≤ Tmax, VCC = 30 V, RL = 2 kΩ µA 1000 + VCC VCC = 30 V, RL = 2 kΩ dB 500 + Output sink current 150 100 Tmin ≤ Tamb ≤ Tmax, VCC = 30 V Isink mV 200 = 15 V, RL = 2 kΩ, Vo = 1.4 to 11.4 V + VCC Unit 30 50 + Supply current, no load 4 Tmin ≤ Tamb ≤ Tmax, TS321 VCC = 5 V ICC 0.5 2 (2) Large signal voltage gain Max. TS321A + VCC Avd Typ. 26 µA 60 mA 27 + VCC = 30 V, RL = 10 kΩ + VOH High-level output voltage 25.5 27 Tmin ≤ Tamb ≤ Tmax, VCC = 30 V, RL = 10 kΩ 26.5 VCC = 5 V, RL = 2 kΩ 3.5 28 + + Tmin ≤ Tamb ≤ Tmax, VCC = 5 V, RL = 2 kΩ V + VOL Low level output voltage RL = 10 kΩ 3 5 Tmin ≤ Tamb ≤ Tmax, RL = 10 kΩ 15 20 mV + SR Slew rate VCC = 15 V, Vi = 0.5 to 3 V, RL = 2 kΩ, CL = 100 pF, unity gain DocID6298 Rev 9 0.4 V/µs 5/15 Electrical characteristics Symbol TS321 Parameter Test conditions Min. Typ. Max. Unit + VCC GBP ϕm THD en Gain bandwidth product = 30 V, f = 100 kHz, Vin = 10 mV, RL = 2 kΩ, CL = 100 pF Phase margin Total harmonic distortion f = 1 kHz, Av = 20 dB, RL = 2 kΩ, Vo = 2 Vpp, CL = 100 pF, + VCC = 30 V Equivalent input noise voltage f = 1 kHz, Rs = 100 Ω, + VCC = 30 V 0.8 MHz 60 Degrees 0.015 % 40 nV -----------Hz Notes: (1) + + Vo = 1.4 V, Rs = 0 Ω, 5 V < (VCC ) < 30 V, 0 < Vicm < (VCC ) - 1.5 V (2) The direction of the input current is out of the IC. This current is essentially constant and independent of the state of the output. Therefore, there is no change in the load on the input lines. Figure 2: Current consumption versus temperature Figure 3: AC-coupled inverting amplifier V Figure 4: Non-inverting DC gain 6/15 Figure 5: AC-coupled non-inverting amplifier DocID6298 Rev 9 TS321 Electrical characteristics Figure 6: DC summing amplifier DocID6298 Rev 9 7/15 Macromodel TS321 4 Macromodel 4.1 Important note concerning this macromodel Please not the following points before using this macromodel • • • All models are a trade-off between accuracy and complexity (that is, simulation time) Macromodels are not a substitute for breadboarding, rather, they confirm the validity of a design approach and help to select surrounding component values. A macromodel emulates the nominal performance of a typical device within specified operating conditions (for example, temperature and supply voltage). Thus, the macromodel is often not as exhaustive as the datasheet. Its purpose is to illustrate the main parameters of the product. Data derived from macromodels used outside the specified conditions (for example, VCC and temperature) or even worse, outside of the device’s operating conditions (for example, VCC and Vicm), are not reliable in any way. 4.2 Macromodel code ** Standard Linear Ics Macromodels, 1993. ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT TS321 1 2 3 4 5 *************************** .MODEL MDTH D IS=1E-8 KF=3.104131E-15 CJO=10F * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 2.600000E+01 RIN 15 16 2.600000E+01 RIS 11 15 2.003862E+02 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0 VOFN 13 14 DC 0 IPOL 13 5 1.000000E-05 CPS 11 15 3.783376E-09 DINN 17 13 MDTH 400E-12 8/15 DocID6298 Rev 9 TS321 Macromodel VIN 17 5 0.000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 2.000000E+00 FCP 4 5 VOFP 3.400000E+01 FCN 5 4 VOFN 3.400000E+01 FIBP 2 5 VOFN 2.000000E-03 FIBN 5 1 VOFP 2.000000E-03 * AMPLIFYING STAGE FIP 5 19 VOFP 3.600000E+02 FIN 5 19 VOFN 3.600000E+02 RG1 19 5 3.652997E+06 RG2 19 4 3.652997E+06 CC 19 5 6.000000E-09 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 7.500000E+03 VIPM 28 4 1.500000E+02 HONM 21 27 VOUT 7.500000E+03 VINM 5 27 1.500000E+02 EOUT 26 23 19 5 1 VOUT 23 5 0 ROUT 26 3 20 COUT 3 5 1.000000E-12 DOP 19 25 MDTH 400E-12 VOP 4 25 2.242230E+00 DON 24 19 MDTH 400E-12 VON 24 5 7.922301E-01 .ENDS DocID6298 Rev 9 9/15 Macromodel 4.3 TS321 Electrical characteristics of the macromodel + - Table 4: Electrical characteristics at VCC = 3 V, VCC = 0 V, RL and CL connected to VCC/2, Tamb = 25 °C (unless otherwise specified) Symbol Conditions Vio Unit 0 mV Avd RL = 2 kΩ 100 V/mV ICC No load, per operator 300 µA 0 to 3.5 V 3.5 V 5 mV 40 mA 0.8 MHz 0.4 V/µs 60 Degrees Vicm VOH VOL Ios RL = 2 kΩ Vo = 0 V GBP SR RL = 2 kΩ, CL = 100 pF ϕm 10/15 Value DocID6298 Rev 9 TS321 5 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ® ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ® ECOPACK is an ST trademark. DocID6298 Rev 9 11/15 Package information 5.1 TS321 SOT23-5 package information Figure 7: SOT23-5 package mechanical drawing Table 5: SOT23-5 package mechanical data Dimensions Millimeters Ref. A Min. Typ. Max. Min. Typ. Max. 0.90 1.20 1.45 0.035 0.047 0.057 A1 12/15 Inches 0.15 0.006 A2 0.90 1.05 1.30 0.035 0.041 0.051 B 0.35 0.40 0.50 0.014 0.016 0.020 C 0.09 0.15 0.20 0.004 0.006 0.008 D 2.80 2.90 3.00 0.110 0.114 0.118 D1 1.90 0.075 e 0.95 0.037 E 2.60 2.80 3.00 0.102 0.110 0.118 F 1.50 1.60 1.75 0.059 0.063 0.069 L 0.10 0.35 0.60 0.004 0.014 0.024 K 0 degrees 10 degrees 0 degrees DocID6298 Rev 9 10 degrees TS321 Ordering information 6 Ordering information Table 6: Order codes Order code Temperature range Package Packaging TS321ILT K401 TS321AILT TS321IYLT Marking (1) TS321AIYLT -40 °C to 125 °C SOT23-5 (1) Tape and reel K402 K406 K407 Notes: (1) Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 and Q 002 or equivalent. DocID6298 Rev 9 13/15 Revision history 7 TS321 Revision history Table 7: Document revision history Date Revision 30-Jun-2001 1 Initial release 04-Jul-2005 2 PPAP references inserted in the datasheet, see order codes table. ESD protection inserted in Table 1: Absolute maximum ratings. 06-Sep-2005 3 Correction of errors in package names and markings in order codes table. Minor grammatical and formatting corrections. 4 Missing PPAP references inserted, see order codes table. Thermal resistance junction to ambient and thermal resistance junction to case information added in Table 1: Absolute maximum ratings. Macromodel updated see Section 4: Macromodel. 08-Nov-2007 5 Added CDM value for SO-8 in Table 1: Absolute maximum ratings. Added Tj value in Table 1: Absolute maximum ratings. Macromodel updated see Section 4: Macromodel. Reformatted package information. Added footnote in Table 7: Order codes. Removed TS321IYD/IYDT and TS321AIYD/AIYDT order codes. 08-Jul-2008 6 Added CDM value for SOT23-5 package in Table 1: Absolute maximum ratings. 10-May-2010 7 Updated package information in Chapter 5. 12-Sep-2010 8 Qualified status of TS321IYLT and TS321AIYLT order codes in Table 7: Order codes, minor corrections throughout document. 9 Removed SO8 package and all references to it Table 1: Absolute maximum ratings: Updated ESD, HBM data Section 5.1: updated SOT23-5 package information Table 7: Order codes: removed obsolete order codes (TS321ID, TS321IDT, TS321AID, TS321AIDT) 12-Dec-2005 12-Nov-2014 14/15 Changes DocID6298 Rev 9 TS321 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2014 STMicroelectronics – All rights reserved DocID6298 Rev 9 15/15