TS339CD

TS339 Micropower quad CMOS voltage comparator Datasheet − production data Features ■ Extremely low supply current: 9 μA typ./comp. ■ Wide single supply range 2.7 V to 16 V or dual supplies (±1.35 V to ±8 V) ■ Extremely low input bias current: 1 pA typ. ■ Extremely low input offset current: 1 pA typ. ■ Input common-mode voltage range includes GND ■ High input impedance: 1012 Ω typ. ■ Fast response time: 1.5 ms typ. for 5 mV overdrive ■ Pin-to-pin and functionally compatible with bipolar LM339 device N DIP14 (plastic package) D SO14 (plastic micropackage) P TSSOP14 (thin shrink small outline package) Description The TS339 device is a micropower CMOS quad voltage comparator with extremely low consumption of 9 μA typ. / comparator (20 times less than bipolar LM339). Similar performances are offered by the quad micropower comparator TS3704 with a push-pull CMOS output. Figure 1. Thus response times remain similar to the LM339 device. Table 1. Pin connection (top view) /UTPUT   /UTPUT /UTPUT   /UTPUT 6##   6## )NVERTINGINPUT    .ON INVERTINGINPUT  .ON INVERTINGINPUT     )NVERTINGINPUT  )NVERTINGINPUT    .ON INVERTINGINPUT  .ON INVERTINGINPUT     )NVERTINGINPUT  Device summary Order code Temperature range TS339CN Package Packaging Marking DIP14 Tube TS339CN SO14 Tube or tape and reel S339C DIP14 Tube TS339IN SO14 Tube or tape and reel S339I TSSOP14 (thin shrink outline package) Tape and reel S339I 0 °C, +70 °C TS339CD/CDT TS339IN -40 °C, +125 °C TS339ID/IDT TS339IPT September 2012 This is information on a product in full production. Doc ID 4065 Rev 3 1/11 www.st.com 11 Absolute maximum ratings 1 TS339 Absolute maximum ratings Table 2. Key parameters and their absolute maximum ratings Symbol VCC+ Vid Parameter Value Unit 18 V Supply voltage(1) (2) ±18 V Vi Input voltage (3) 18 V Vo Output voltage 18 V Io Output current 20 mA 50 mA 1500 830 710 mW Storage temperature range -65 to +150 °C HBM: human body model(6) 50 V 40 V 800 V IF pd Tstg ESD Differential input voltage Forward current in ESD protection diodes on Power dissipation DIP14 SO14 TSSOP14 MM: machine inputs(4) (5) model(7) CDM: charged device model 1. All voltage values, except differential voltage, are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. Excursions of input voltages may exceed the power supply level. As long as the common mode voltage [Vicm =(Vin+ + Vin-)/2] remains within the specified range, the comparator will provide a stable output state. However, the maximum current through the ESD diodes (IF) of the input stage must strictly be observed. 4. Guaranteed by design. 5. Pd is calculated with Tamb = +25 °C, Tj = +150 °C and Rthja = 80 °C/W for DIP14 package Rthja = 150 °C/W for SO14 package Rthja = 175 °C/W for TSSOP14 package. 6. Human body model, 100pF discharged through a 1.5 kΩ resistor into pin of device. 7. Machine model ESD, a 200 pF cap is charged to the specified voltage, then discharged directly into the IC with no external series resistor (internal resistor < 5 Ω), into pin to pin of device. 2/11 Doc ID 4065 Rev 3 TS339 Typical application schematics 2 Typical application schematics Figure 2. Schematic diagram (for 1/4 TS339) VCC + T10 T1 T2 T9 T17 R1 T11 T12 Input T3 T T18 Input + Output 4 T20 T13 T8 T19 T5 T7 T14 T15 T16 T6 VCC - Doc ID 4065 Rev 3 3/11 Electrical characteristics TS339 3 Electrical characteristics Table 3. VCC+ = 3 V, VCC- = 0 V, Tamb = 25 °C (unless otherwise specified) Symbol Parameter Min. Typ. Vio Input offset voltage(1) Vic = 1.5 V Tmin. ≤ Tamb ≤ Tmax. Iio Input offset current(2) Vic = 1.5 V Tmin. ≤ Tamb ≤ Tmax. 1 Input bias current (2) Vic = 1.5 V Tmin. ≤ Tamb ≤ Tmax. 1 Iib Max. Unit 5 6.5 mV pA 300 pA 600 VCC+-1.2 VCC+ -1.5 Vicm Input common mode voltage range Tmin. ≤ Tamb ≤ Tmax 0 0 CMR Common-mode rejection ratio Vic = Vicm min. 70 SVR Supply voltage rejection ratio VCC+ = 3 V to 5 V 70 IOH High level output current Vid = +1 V, VOH = 3 V Tmin. ≤ Tamb ≤ Tmax. 2 40 1000 nA VOL Low level output voltage Vid = -1 V, IOL = +6 mA Tmin. ≤ Tamb ≤ Tmax. 400 550 800 mV ICC Supply current (each comparator) No load - outputs low Tmin. ≤ Tamb ≤ Tmax. 9 20 25 μA tPLH Response time low to high Vic = 0 V, f = 10 kHz, Tmin. ≤Tamb ≤TmaxCL = 50 pF, overdrive = 5 mV TTL input 1.5 0.7 μs tPHL Response time high to low Vic = 0 V, f = 10 kHz, RL = 5.1 kΩ, CL = 50 pF, overdrive = 5 mV TTL input 2.5 0.08 μs 1. The specified offset voltage is the maximum value required to drive the output up to 2.5 V or down to 0.3 V. 2. Maximum values including unavoidable inaccuracies of the industrial test. 4/11 Doc ID 4065 Rev 3 V dB dB TS339 Table 4. Electrical characteristics VCC+ = 5 V, VCC- = 0 V, Tamb = 25 °C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Unit 1.4 5 6.5 mV Vio Input offset voltage(1) Vic = 2.5 V, Vcc+ = 5 V to 10 V Tmin. ≤ Tamb ≤ Tmax. Iio Input offset current(2) Vic = 2.5 V Tmin. ≤ Tamb ≤ Tmax. 1 Input bias current(2) Vic = 2.5 V Tmin. ≤ Tamb ≤ Tmax. 1 Iib pA 300 pA 600 VCC+-1.2 VCC+ -1.5 Vicm Input common mode voltage range Tmin. ≤ Tamb ≤ Tmax CMR Common-mode rejection ratio Vic = 0 V 75 SVR Supply voltage rejection ratio VCC+ = +5 V to +10 V 85 IOH High level output voltage Vid = 1 V, VOH = +5 V Tmin. ≤ Tamb ≤ Tmax. 27 40 1000 nA VOL Low level output voltage Vid = -1 V, IOL = 6 mA Tmin. ≤ Tamb ≤ Tmax. 260 400 650 mV ICC Supply current (each comparator) No load - outputs low Tmin. ≤Tamb ≤Tmax. 10 20 25 μA tPLH Response time low to high Vic = 0 V, f = 10 kHz, RL = 5.1 kΩ, CL = 15 pF, overdrive = 5 mV Overdrive = 10 mV Overdrive = 20 mV Overdrive = 40 mV TTL input 1.5 1.2 1.1 0.9 0.8 tPHL Response time high to low Vic = 0 V, f = 10 kHz, RL = 5.1 kΩ, CL = 15 pF, overdrive = 5 mV Overdrive = 10 mV Overdrive = 20 mV Overdrive = 40 mV TTL input 2.5 1.9 1.2 0.8 0.08 tf 0 0 Fall time f = 10 kHz, CL = 50 pF, R L = 5.1 kΩ, overdrive 50 mV V dB dB 30 μs μs ns 1. The specified offset voltage is the maximum value required to drive the output up to 4.5 V or down to 0.3 V. 2. Maximum values including unavoidable inaccuracies of the industrial test. Doc ID 4065 Rev 3 5/11 Package information 4 TS339 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 6/11 Doc ID 4065 Rev 3 TS339 4.1 Package information DIP14 package Figure 3. DIP14 package outline Table 5. DIP-14 package mechanical data Dimensions Symbol mm Min. a1 0.51 B 1.39 Typ. inch Max. Min. Typ. Max. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 Doc ID 4065 Rev 3 0.050 0.100 7/11 Package information 4.2 TS339 SO14 package Figure 4. SO14 package outline Table 6. SO14 package mechanical data Dimensions Symbol mm Min. Typ. A a1 inch Max. Typ. 1.75 0.1 0.2 a2 Max. 0.068 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M 0.68 S 8/11 Min. 8° (max.) Doc ID 4065 Rev 3 0.026 TS339 4.3 Package information TSSOP14 package Figure 5. TSSOP14 package outline ! ! ! B E + C , % $ % 0).)$%.4)&)#!4)/.  $ Table 7. TSSOP14 package mechanical data Dimensions Symbol mm. Min. Typ. A inch Max. Min. Typ. 1.2 A1 0.05 A2 0.8 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 1 0.65 BSC K 0° L 0.45 0.60 0.0256 BSC 8° 0° 0.75 0.018 Doc ID 4065 Rev 3 8° 0.024 0.030 9/11 Revision history TS339 5 Revision history Table 8. Document revision history Date Revision Jan. 2003 1 Initial release. Aug. 2005 2 1 - PPAP references inserted in the datasheet see Table 1: Order codes on page 1. 2 - ESD protection inserted in Table 2 Key parameters and their absolute maximum ratings on page 2. 3 Updated Features, Table 1, removed TS339IYD and TS339IYDT from Table 1. Updated ECOPACK text, reformatted Section 4: Package information. Minor corrections throughout document. 04-Sep-2012 10/11 Changes Doc ID 4065 Rev 3 TS339 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 4065 Rev 3 11/11