TS339IPT

TS339 Micropower quad CMOS voltage comparator Datasheet - production data Features • Extremely low supply current: 9 μA typ./comparator D SO14 (plastic micropackage) • Wide single supply range 2.7 V to 16 V or dual supplies (±1.35 V to ±8 V) • Extremely low input bias current: 1 pA typ. • Extremely low input offset current: 1 pA typ. • Input common-mode voltage range includes GND P TSSOP14 (thin shrink small outline package) • High input impedance: 1012 Ω typ. • Fast response time: 1.5 μs typ. for 5 mV overdrive • Pin-to-pin and functionally compatible with bipolar LM339 device 2XWSXW   2XWSXW 2XWSXW   2XWSXW 9&&  ,QYHUWLQJLQSXW     1RQLQYHUWLQJLQSXW  1RQLQYHUWLQJLQSXW      ,QYHUWLQJLQSXW  ,QYHUWLQJLQSXW     1RQLQYHUWLQJLQSXW  1RQLQYHUWLQJLQSXW      ,QYHUWLQJLQSXW  Description  9&&  Pin connections top view The TS339 device is a micro-power, CMOS, quad voltage comparator with extremely low consumption of 9 μA typ./comparator (20 times less than the bipolar LM339). Similar performances are offered by the quad micropower comparator TS3704 with a push-pull CMOS output. Thus response times remain similar to the LM339 device. Table 1. Device summary Order code Temperature range TS339CDT TS339CPT Package Packaging Marking SO14 0 °C, 70 °C S339C TSSOP14 Tape and reel TS339IDT SO14 -40 °C, 125 °C TS339IPT March 2021 This is information on a product in full production. S339I TSSOP14 DocID4065 Rev 5 1/11 www.st.com Contents TS339 Contents 1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Typical application schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5 2/11 4.1 SO14 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.2 TSSOP14 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 DocID4065 Rev 5 TS339 1 Absolute maximum ratings Absolute maximum ratings Table 2. Key parameters and their absolute maximum ratings Symbol VCC+ Vid Parameter Value Supply voltage(1) Differential input 18 voltage(2) ±18 V Vi Input voltage (3) 18 Vo Output voltage 18 Io Output current 20 IF Forward current in ESD protection diodes on inputs pd Power dissipation(5) SO14 TSSOP14 Tstg ESD Unit mA (4) 50 830 710 mW Storage temperature range -65 to +150 °C HBM: human body model(6) 50 MM: machine model(7) CDM: charged device model 40 V 800 1. All voltage values, except the differential voltage, are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. Excursions of input voltages may exceed the power supply level. As long as the common mode voltage [Vicm=(Vin+ + Vin-)/2] remains within the specified range, the comparator will provide a stable output state. However, the maximum current through the ESD diodes (IF) of the input stage must strictly be observed. 4. Guaranteed by design. 5. Pd is calculated with Tamb = +25 °C, Tj = +150 °C and Rthja = 150 °C/W for SO14 package Rthja = 175 °C/W for TSSOP14 package. 6. Human body model, 100pF discharged through a 1.5 kΩ resistor into pin of device. 7. Machine model ESD, a 200 pF cap is charged to the specified voltage, then discharged directly into the IC with no external series resistor (internal resistor < 5 Ω), into pin to pin of device. DocID4065 Rev 5 3/11 11 Typical application schematics 2 TS339 Typical application schematics Figure 1. Schematic diagram (for 1/4 TS339) VCC + T10 T1 T9 T2 T17 R1 T11 T12 Input T3 T T18 Input + Output 4 T20 T13 T8 T19 T5 T7 T14 T15 T6 VCC - 4/11 DocID4065 Rev 5 T16 TS339 3 Electrical characteristics Electrical characteristics Table 3. VCC+ = 3 V, VCC- = 0 V, Tamb = 25 °C (unless otherwise specified) Symbol Parameter Vio Input offset voltage(1) Vic = 1.5 V Tmin. ≤ Tamb ≤ Tmax. Iio Input offset current(2) Vic = 1.5 V Tmin. ≤ Tamb ≤ Tmax. Min. Typ. Max. Unit 5 6.5 mV 1 300 pA (2) Iib Input bias current Vic = 1.5 V Tmin. ≤ Tamb ≤ Tmax. 1 600 VCC+-1.2 VCC+ -1.5 Vicm Input common mode voltage range Tmin. ≤ Tamb ≤ Tmax 0 0 CMR Common-mode rejection ratio Vic = Vicm min. 70 SVR Supply voltage rejection ratio VCC+ = 3 V to 5 V 70 IOH High level output current Vid = +1 V, VOH = 3 V Tmin. ≤ Tamb ≤ Tmax. 2 40 1000 nA VOL Low level output voltage Vid = -1 V, IOL = +6 mA Tmin. ≤ Tamb ≤ Tmax. 400 550 800 mV ICC Supply current (each comparator) No load - outputs low Tmin. ≤ Tamb ≤ Tmax. 9 20 25 μA tPLH Response time low to high Vic = 0 V, f = 10 kHz, Tmin. ≤ Tamb ≤ TmaxCL = 50 pF, overdrive = 5 mV TTL input 1.5 0.7 tPHL Response time high to low Vic = 0 V, f = 10 kHz, RL = 5.1 kΩ, CL = 50 pF, overdrive = 5 mV TTL input 2.5 0.08 V dB μs 1. The specified offset voltage is the maximum value required to drive the output up to 2.5 V or down to 0.3 V. 2. Maximum values including unavoidable inaccuracies of the industrial test. DocID4065 Rev 5 5/11 11 Electrical characteristics TS339 Table 4. VCC+ = 5 V, VCC- = 0 V, Tamb = 25 °C (unless otherwise specified) Symbol Parameter Vio Input offset voltage(1) Vic = 2.5 V, Vcc+ = 5 V to 10 V Tmin. ≤ Tamb ≤ Tmax. Iio Input offset current(2) Vic = 2.5 V Tmin. ≤ Tamb ≤ Tmax. Min. Typ. Max. Unit 1.4 5 6.5 mV 1 300 pA current(2) Iib Input bias Vic = 2.5 V Tmin. ≤ Tamb ≤ Tmax. 1 600 VCC+-1.2 VCC+ -1.5 Vicm Input common mode voltage range Tmin. ≤ Tamb ≤ Tmax CMR Common-mode rejection ratio Vic = 0 V 75 SVR Supply voltage rejection ratio VCC+ = +5 V to +10 V 85 IOH High level output voltage Vid = 1 V, VOH = +5 V Tmin. ≤ Tamb ≤ Tmax. 27 40 1000 nA VOL Low level output voltage Vid = -1 V, IOL = 6 mA Tmin. ≤ Tamb ≤ Tmax. 260 400 650 mV ICC Supply current (each comparator) No load - outputs low Tmin. ≤ Tamb ≤ Tmax. 10 20 25 μA tPLH Response time low to high Vic = 0 V, f = 10 kHz, RL = 5.1 kΩ, CL = 15 pF, overdrive = 5 mV Overdrive = 10 mV Overdrive = 20 mV Overdrive = 40 mV TTL input 1.5 1.2 1.1 0.9 0.8 tPHL Response time high to low Vic = 0 V, f = 10 kHz, RL = 5.1 kΩ, CL = 15 pF, overdrive = 5 mV Overdrive = 10 mV Overdrive = 20 mV Overdrive = 40 mV TTL input 2.5 1.9 1.2 0.8 0.08 tf 0 0 dB Fall time f = 10 kHz, CL = 50 pF, RL = 5.1 kΩ, overdrive 50 mV 30 1. The specified offset voltage is the maximum value required to drive the output up to 4.5 V or down to 0.3 V. 2. Maximum values including unavoidable inaccuracies of the industrial test. 6/11 V DocID4065 Rev 5 μs ns TS339 4 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. DocID4065 Rev 5 7/11 11 Package information 4.1 TS339 SO14 package information Figure 2. SO14 package outline Table 5. SO14 package mechanical data Dimensions Symbol mm Min. Typ. A a1 inch Max. Typ. 1.75 0.1 0.2 a2 Max. 0.068 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M 0.68 S 8/11 Min. 8° (max.) DocID4065 Rev 5 0.026 TS339 4.2 Package information TSSOP14 package information Figure 3. TSSOP14 package outline $ $ $ E H . / F ( ' ( 3,1,'(17,),&$7,21  ' Table 6. TSSOP14 package mechanical data Dimensions Symbol mm. Min. Typ. A inch Max. Min. Typ. 1.2 A1 0.05 A2 0.8 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 1 0.65 BSC K 0° L 0.45 0.60 0.0256 BSC 8° 0° 0.75 0.018 DocID4065 Rev 5 8° 0.024 0.030 9/11 11 Revision history 5 TS339 Revision history Table 7. Document revision history Date Revision Jan. 2003 1 Initial release. 2 1 - PPAP references inserted in the datasheet see Table 1: Order codes on page 1. 2 - ESD protection inserted in Table 2 Key parameters and their absolute maximum ratings on page 2. 3 Updated Features, Table 1, removed TS339IYD and TS339IYDT from Table 1. Updated ECOPACK text, reformatted Section 4: Package information. Minor corrections throughout document. 21-Feb-2014 4 Removed DIP package Features: updated fast response time Device summary: removed order codes TS339CN, TS339IN, and TS339ID; added temperature range for order codes TS339IDT and TS339IPT 16-Mar-2021 5 Updated the device summary table in cover page. Aug. 2005 04-Sep-2012 10/11 Changes DocID4065 Rev 5 TS339 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2021 STMicroelectronics – All rights reserved DocID4065 Rev 5 11/11 11