TS3702I

TS3702C,I,M MICROPOWER DUAL CMOS VOLTAGE COMPARATORS . . . . . . . . . PUSH-PULL CMOS OUTPUT (NO EXTERNAL PULL-UP RESISTOR REQUIRED) EXTREMELY LOW SUPPLY CURRENT : 9µA TYP / COMPARATOR WIDE SINGLE SUPPLY RANGE (3V TO 16V) OR DUAL SUPPLIES (± 1.5V TO ± 8V) EXTREMELY LOW INPUT BIAS CURRENT : 1pA TYP EXTREMELY LOW INPUT OFFSET CURRENT : 1pA TYP INPUT COMMON-MODE VOLTAGE RANGE INCLUDES GND HIGH INPUT IMPEDANCE : 1012Ω TYP FAST RESPONSE TIME : 2µs TYP FOR 5mV OVERDRIVE PIN-TO-PIN AND FUNCTIONALLY COMPATIBLE WITH BIPOLAR LM393 N DIP8 (Plastic Package) D SO8 (Plastic Micropackage) ORDER CODES Part Number TS3702C TS3702I TS3702M Example : TS3702CN Temperature Range 0 C, +70 C -40oC, +125oC -55 C, +125 C o o o o Package N q q q D q q q PIN CONNECTIONS (top view) Output 1 1 2 3 4 + + 8 7 6 5 V CC + Output 2 Inverting Input 2 Non-inverting Input 2 DESCRIPTION The TS3702 is a micropower CMOS dual voltage comparator with extremely low consumption of 9µA typ / comparator (20 times less than bipolar LM393). The push-pull CMOS output stage allows power and space saving by eliminating the external pull-up resistor required by usual open-collector output comparators. Thus response times remain similar to the LM393. October 1997 Inverting Input 1 Non-inverting Input 1 VCC - 1/5 TS3702C,I,M SCHEMATIC DIAGRAM (for 1/2 TS3702) VCC + T 10 T1 T2 T9 T 17 R1 Input T3 T4 T 11 T12 Input + T 18 T 21 Output T 13 T8 T 19 T 20 T5 T6 T7 T 14 T 15 T 16 V CC - MAXIMUM RATINGS Symbol VCC+ Vid Vi VO IO Toper Supply Voltage - (note 1) Differential Input Voltage - (note 2) Input Voltage - (note 3) Output Voltage Output Current Operating Free-Air Temperature Range TS3702C TS3702I TS3702M Tstg Notes : 1. 2. 3. 4. Parameter Value 18 ±18 18 18 20 0 to +70 -40 to +125 -55 to +125 -65 to +150 Unit V V V V mA o C Storage Temperature Range o C All voltage values, except differential voltage, are with respect to network ground terminal. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. The magnitude of the input and the output voltages must never exceed the magnitude of the positive supply voltage. Short circuit from outputs to VCC+ can cause excessive heating and eventual destruction. OPERATING CONDITIONS Symbol VCC+ Vicm 2/5 Supply Voltage Common Mode Input Voltage Range Parameter TS3702C,I TS3702M Value 3 to 16 4 to 16 0 to VCC -1.5 + Unit V V TS3702C,I,M ELECTRICAL CHARACTERISTICS VCC+ = 5V, VCC- = 0V, Tamb = 25°C (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage Vic = Vicm min., VCC+ = 5V to 10V - (note 1) Tmin. ≤ Tamb ≤ Tmax. Input Offset Current - (note 2) Vic = 2.5 V Tmin. ≤ Tamb ≤ Tmax. Input Bias Current - (note 2) Vic = 2.5 V Tmin. ≤ Tamb ≤ Tmax. Input Common Mode Voltage Range Tmin. ≤ Tamb ≤ Tmax. Common-mode Rejection Ratio Vic = Vicm min. Supply Voltage Rejection Ratio + VCC = +5V to +10V High Level Output Voltage Vid = 1V, IOH = -4mA Tmin. ≤ Tamb ≤ Tmax. Low Level Output Voltage Vid = -1V, IOL = 4mA Tmin. ≤ Tamb ≤ Tmax. Supply Current (2 comparators) No load - Outputs low Tmin. ≤ Tamb ≤ Tmax. Response Time Low to High Vic = 0V, f = 10kHz, CL = 50pF, Overdrive Overdrive Overdrive Overdrive TTL Input = 5mV = 10mV = 20mV = 40mV 4.5 4.3 + 0 to VCC -1.2 + 0 to VCC -1.5 Min. Typ. 1.2 Max. 5 6.5 Unit mV Iio pA 1 300 pA 1 600 V dB 82 dB 90 V 4.7 mV 220 300 375 40 50 µA µs 1.5 1.1 0.9 0.7 0.6 2.2 1.6 1.1 0.75 0.17 30 µs Iib Vicm CMR SVR VOH VOL ICC 18 tPLH tPHL Response Time High to Low Vic = 0V, f = 10kHz, CL = 50pF, Overdrive = 5mV Overdrive = 10mV Overdrive = 20mV Overdrive = 40mV TTL Input tf Fall time f = 10kHz, CL = 50pF, Overdrive 50mV ns Note : 1. The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V. 2. Maximum values including unavoidable inaccuracies of the industrial test. 3/5 TS3702C,I,M PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Dimensions A a1 B b b1 D E e e3 e4 F i L Z Min. 0.51 1.15 0.356 0.204 7.95 Millimeters Typ. 3.32 Max. Min. 0.020 0.045 0.014 0.008 0.313 Inches Typ. 0.131 Max. 1.65 0.55 0.304 10.92 9.75 2.54 7.62 7.62 6.6 5.08 3.81 1.52 0.065 0.022 0.012 0.430 0.384 0.100 0.300 0.300 0260 0.200 0.150 0.060 3.18 0.125 4/5 DIP8.TBL PM-DIP8.EPS TS3702C,I,M PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) Dimensions A a1 a2 a3 b b1 C c1 D E e e3 F L M S Min. 0.1 0.65 0.35 0.19 0.25 4.8 5.8 Millimeters Typ. Max. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 45 (typ.) 5.0 6.2 o Min. 0.004 0.026 0.014 0.007 0.010 0.189 0.228 Inches Typ. Max. 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.197 0.244 1.27 3.81 3.8 0.4 4.0 1.27 0.6 8 (max.) o 0.050 0.150 0.150 0.016 0.157 0.050 0.024 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned in this publication are subject to change without notice. This publ ication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. ORDER CODE : © 1997 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 5/5 SO8.TBL PM-SO8.EPS