TS3V902I

TS3V902 3V RAIL TO RAIL CMOS DUAL OPERATIONAL AMPLIFIER (WITH STANDBY POSITION) . . . . . . . . DEDICATED TO 3.3V OR BATTERY SUPPLY (specified at 3V and 5V) RAIL TO RAIL INPUT AND OUTPUT VOLTAGE RANGES STANDBY POSITION : REDUCED CONSUMPTION (0.5µA) AND HIGH IMPEDANCE OUTPUTS SINGLE (OR DUAL) SUPPLY OPERATION FROM 2.7V TO 16V EXTREMELY LOW INPUT BIAS CURRENT : 1pA TYP SPECIFIED FOR 600Ω AND 100Ω LOADS LOW SUPPLY CURRENT : 200µA/Ampli SPICE MACROMODEL INCLUDED IN THIS SPECIFICATION N DIP14 (Plastic Package) D SO14 (Plastic Micropackage) ORDER CODES Part Number TS3V902I/AI Temperature Range -40, +125 C o Package N • D • PIN CONNECTIONS (top view) DESCRIPTION The TS3V902 is a RAIL TO RAIL dual CMOS operational amplifier designed to operate with single or dual supply voltage. The input voltage range Vicm includes the two supply rails VCC+ and VCC-. The output reaches (VCC = 5V) : • VCC- +50mV VCC+ -50mV with RL = 10kΩ • VCC- +350mV VCC+ -400mV with RL = 600Ω This product offers a broad supply voltage operating range from 2.7V to 16V and a supply current of only 200µA/amp. (VCC = 3V). Source and sink output current capability is typically 40mA (at VCC = 3V), fixed by an internal limitation circuit. The TS3V902 can be put on STANDBY position (only 0.5µA and high impedance outputs). SGS-THOMSON is offering a quad op-amp with the same features : TS3V904. October 1997 Standby 1 Output 1 2 14 13 12 V CC+ Output 2 N.C. Inverting Input 2 Non-inverting Input 2 N.C. V CC - N.C. 3 Inverting Input 1 Non-inverting input 1 N.C. 4 5 6 + + 11 10 9 8 N.C. 7 1/11 TS3V902 SCHEMATIC DIAGRAM (1/2 TS3V902) VCC S ta ndby S ta ndby Non-inve rting Input Interna l Vref Inve rting Input S ta ndby Output S ta ndby VCC STANDBY POSITION VCC HIGH IMPEDANCE OUTPUT IN STANDBY MODE 1/2 TS 3V902 1 VCC S TBY ON Vsby VCC S TBY OFF VCC ABSOLUTE MAXIMUM RATINGS Symbol VCC Vid Vi Iin Io Toper Tstg Notes : Parameter Supply Voltage - (note 1) Differential Input Voltage - (note 2) Input Voltage - (note 3) Current on Inputs Current on Outputs Operating Free Air Temperature Range TS3V902I/AI Storage Temperature Value 18 ±18 -0.3 to 18 ±50 ± 130 -40 to +125 -65 to +150 Unit V V V mA mA o C o C 1. All voltage values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of input and output voltages must never exceed VCC+ +0.3V. OPERATING CONDITIONS Symbol VCC Vicm Parameter Supply Voltage Common Mode Input Voltage Range Value 2.7 to 16 + VCC -0.2 to VCC +0.2 Unit V V 2/11 TS3V902 ELECTRICAL CHARACTERISTICS VCC+ = 3V, VCC- = 0V, RL,CL connected to VCC/2, Standby OFF, Tamb = 25oC (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage (V ic = Vo = VCC/2) Tmin. ≤ Tamb ≤ Tmax. DVio Iio Iib ICC CMR SVR Avd VOH TS3V902 TS3V902A TS3V902 TS3V902A Min. TS3V902I/AI Typ. Max. 10 5 12 7 5 1 100 200 1 150 300 200 300 400 60 80 10 2.97 2.7 2 Unit mV VOL Io GBP SR ∅m en VO1/VO2 Input Offset Voltage Drift Input Offset Current - (note 1) Tmin. ≤ Tamb ≤ Tmax. Input Bias Current - (note 1) Tmin. ≤ Tamb ≤ Tmax. Supply Current (per amplifier, AVCL = 1, no load) Tmin. ≤ Tamb ≤ Tmax. Common Mode Rejection Ratio Vic = 0 to 3V, Vo = 1.5V + Supply Voltage Rejection Ratio (VCC = 2.7 to 3.3V, VO = VCC /2) Large Signal Voltage Gain (RL = 10kΩ, VO = 1.2V to 1.8V) Tmin. ≤ Tamb ≤ Tmax. High Level Output Voltage (V id = 1V) RL = 10kΩ RL = 600Ω RL = 100Ω RL = 10kΩ Tmin. ≤ Tamb ≤ Tmax. RL = 600Ω Low Level Output Voltage (Vid = -1V RL = 10kΩ RL = 600Ω RL = 100Ω RL = 10kΩ Tmin. ≤ Tamb ≤ Tmax. RL = 600Ω − Output Short Circuit Current (Vid = ±1V) Source (Vo = VCC ) + Sink (Vo = VCC ) Gain Bandwidth Product (AVCL = 100, RL = 10kΩ, CL = 100pF, f = 100kHz) Slew Rate (AVCL = 1, RL = 10kΩ, CL = 100pF, Vi = 1.3V to 1.7V) Phase Margin Equivalent Input Noise Voltage (Rs = 100Ω, f = 1kHz) Channel Separation (f = 1kHz) µV/oC pA pA µA dB dB V/mV V 3 2 2.9 2.2 2.8 2.1 30 250 900 100 600 150 900 mV 40 40 0.7 0.5 30 30 120 mA MHz V/µs Degrees nV  Hz √ dB Note 1 : Maximum values including unavoidable inaccuracies of the industrial test. STANDBY MODE VCC+ = 3V, VCC- = 0V, Tamb = 25oC (unless otherwise specified) Symbol VinSBY/ON VinSBY/OFF ICC SBY Parameter Pin 1 Threshold Voltage for STANDBY ON Pin 1 Threshold Voltage for STANDBY OFF Total Consumption in Standby Position (STANDBY ON) Min. TS3V902I/AI Typ. 1.2 1.2 0.5 Max. Unit V V µA 3/11 TS3V902 ELECTRICAL CHARACTERISTICS VCC+ = 5V, VCC- = 0V, RL,CL connected to VCC/2, Standby OFF, Tamb = 25oC (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage (Vic = Vo = VCC/2) Tmin. ≤ Tamb ≤ Tmax. DVio Iio Iib ICC CMR SVR Avd VOH TS3V902 TS3V902A TS3V902 TS3V902A Min. TS3V902I/AI Typ. Max. 10 5 12 7 5 1 100 200 1 150 300 230 350 450 85 80 30 4.95 4.6 3.7 Unit mV VOL Io GBP SR ∅m Input Offset Voltage Drift Input Offset Current - (note 1) Tmin. ≤ Tamb ≤ Tmax. Input Bias Current - (note 1) Tmin. ≤ Tamb ≤ Tmax. Supply Current (per amplifier, A VCL = 1, no load) Tmin. ≤ Tamb ≤ Tmax. Common Mode Rejection Ratio Vic = 1.5 to 3.5V, Vo = 2.5V + Supply Voltage Rejection Ratio (VCC = 2.7 to 3.3V, VO = VCC /2) Large Signal Voltage Gain (RL = 10kΩ, VO = 1.5V to 3.5V) Tmin. ≤ Tamb ≤ Tmax. High Level Output Voltage (Vid = 1V) R L = 10kΩ R L = 600Ω R L = 100Ω R L = 10kΩ Tmin. ≤ Tamb ≤ Tmax. R L = 600Ω Low Level Output Voltage (Vid = -1V) R L = 10kΩ R L = 600Ω R L = 100Ω R L = 10kΩ Tmin. ≤ Tamb ≤ Tmax. R L = 600Ω − Output Short Circuit Current (Vid = ±1V) Source (Vo = VCC ) + Sink (Vo = VCC ) Gain Bandwidth Product (AVCL = 100, RL = 10kΩ, CL = 100pF, f = 100kHz) Slew Rate (AVCL = 1, R L = 10kΩ, CL = 100pF, Vi = 1V to 4V) Phase Margin µV/oC pA pA µA dB dB V/mV V 7 5 4.85 4.2 4.8 4.1 50 350 1400 100 680 150 900 mV 60 60 0.8 0.8 30 mA MHz V/µs Degrees Note 1 : Maximum values including unavoidable inaccuracies of the industrial test. STANDBY MODE VCC+ = 5V, VCC- = 0V, Tamb = 25oC (unless otherwise specified) Symbol VinSBY/ON VinSBY/OFF ICC SBY Parameter Pin 1 Threshold Voltage for STANDBY ON Pin 1 Threshold Voltage for STANDBY OFF Total Consumption in Standby Position (STANDBY ON) Min. TS3V902I/AI Typ. 5.2 5.2 0.5 Max. Unit V V µA 4/11 TS3V902 TYPICAL CHARACTERISTICS Figure 1a : Supply Current (each amplifier) versus Supply Voltage 600 500 400 300 200 100 0 4 8 12 16 Figure 1b : Supply Current (each amplifier) versus Supply Voltage (in STANDBY mode) 50 SUPPLY CURRENT, I CC ( µA) SUPPLY CURRENT, ICC ( mA) Ta mb = 25 C A VCL = 1 V o = VCC / 2 S tandby OFF 40 30 20 10 Ta mb = 25 C A VCL = 1 Sta ndby ON 0 4 8 12 16 S UPP LY VOLTAGE, VCC (V) SUPPLY VOLTAGE, V CC (V) Figure 2 : Input Bias Current versus Temperature 100 Figure 3a : High Level Output Voltage versus High Level Output Current 5 OUTPUT VOLTAGE, VOH (V) INPUT BIAS CURRENT, I ib (pA) VCC = 10V Vi = 5V No load Sta ndby OFF 4 3 2 T a mb = 25 C V id = 100mV S tandby OFF VCC = +5V 10 VCC = +3V 1 0 1 25 50 75 100 125 -70 -56 -4 2 -28 -1 4 0 TEMPERATURE , Tamb ( C) OUTPUT CURRENT, IOH (m A) Figure 3b : High Level Output Voltage versus High Level Output Current 20 OUTPUT VOLTAGE, VOH (V) T a mb = 25 C V id = 100mV S tandby OFF Figure 4a : Low Level Output Voltage versus Low Level Output Current 5 T a mb = 25 C V id = 1 00mV S tandby OFF 16 12 8 4 0 -70 VCC = +16V OUTPUT VOLTAGE, V OL (V) 4 3 2 1 VCC = +10 V VCC = +3V VCC = +5V -56 -42 -28 -14 0 0 14 28 42 56 70 OUTP UT CURRENT, IOH (m A) OUTPUT CURRENT, I OL (mA) 5/11 TS3V902 Figure 4b : Low Level Output Voltage versus Low Level Output Current 10 OUTPUT VOLTAGE, VOL (V) Figure 5a : Open Loop Frequency Response and Phase Shift 50 40 GAIN 0 GAIN (dB) 30 20 10 0 -10 P HASE Tamb = 25 C VCC = 10V R L = 10k Ω C L = 100pF AVCL = 100 S tandby OFF 6 4 2 V V CC = 16V P ha s e Margin 45 90 135 CC = 10V Ga in Bandwidth P roduct 180 0 14 28 42 56 70 10 2 10 3 OUTPUT CURRENT, I OL (mA) 10 10 10 FREQUENCY, f (Hz) 4 5 6 10 7 Figure 5b : Open Loop Frequency Response and Phase Shift 50 40 GAIN 0 45 P ha s e Margin Ga in Ba ndwidth P roduct Figure 6a : Gain Bandwidth Product versus Supply Voltage GAIN BANDW. PROD., GBP (kHz) 1800 1400 1000 GAIN (dB) 30 20 10 0 10 10 2 P HASE Ta mb = 25 C VCC = 10V R L = 60 0Ω C L = 10 0pF A VCL = 100 S ta nd by O FF 90 135 180 PHASE (Degrees) Ta mb = 25 C R L = 10k Ω C L = 100pF Sta ndby OFF 600 200 10 3 10 10 10 FREQUENCY, f (Hz) 4 5 6 10 7 0 4 8 12 16 S UPP LY VOLTAGE, VCC (V) Figure 6b : Gain bandwidthProduct versus Supply Voltage GAIN BANDW. PROD., GBP (kHz) 1800 1400 1000 Figure 7a : Phase Margin versus Supply Voltage PHASE MARGIN, φ m (Degrees) 60 50 40 30 20 Ta mb = 25 C R L = 600Ω C L = 100pF Sta ndby OFF Tamb = 2 5 C R L = 1 0kΩ C L = 1 00p F Sta ndby OFF 6 00 200 0 4 8 12 16 0 4 8 12 16 SUPP LY VOLTAGE, VCC (V) S UPP LY VOLTAGE, VCC (V) 6/11 PHASE (Degrees) 8 T a mb = 25 C V id = 100mV S ta ndby OFF TS3V902 Figure 7b : Phase Margin versus Supply Voltage PHASE MARGIN,φ m (Degrees) 60 50 40 30 20 Figure 8 : Input Voltage Noise versus Frequency Ta mb = 25 C R L = 600Ω C L = 100 pF Sta ndby OFF EQUIVALENT INPUT VOLTAGE NOISE (nV/VHz) 150 100 VCC = 10V Tamb = 25 C R S = 100Ω Sta ndby OFF 50 0 0 4 8 12 16 10 SUP PLY VOLTAGE, VCC (V) 1000 100 FREQUENCY (Hz) 10000 STANDBY APPLICATION The two operators of the TS3V902 are both put on STANDBY. The standby pin 1 should never stay unconnected. The ”standby OFF” state, is reached when the pin 1 voltage is higher than Vin SBY/OFF. The ”standby ON” state is assured by a pin 1 voltage lower than Vin SBY/ON. (see electrical characteristics) . . . . In this configuration (standby ON) : The total consumption of the circuit is considerably reduced down to 0.5µA (VCC = 3V). This standby consumption versus VCC curve is given figure 1b. The both outputs are in high impedance state. No output current can then be sourced or sinked by the device. ORDERING INFORMATION 3 T S V 9 0 2 A I N 3V FAMILY RAIL TO RAIL OP AMPs OFFS ET VOLTAGE S ELECTION I ”Nothing” A 10mV max. 5mV max. TEMPERATURE RANGE -40 C to +125 C P ACKAGES N D DT DIP S0 S 0 Ta pe & Ree l 12 02 DUAL - 200µA/amp - 0.7MHz DUAL - 200µA/amp - 0.7MHz + S TANDBY position with High Impe dance Outputs 7/11 TS3V902 MACROMODEL . . . RAIL TO RAIL INPUT AND OUTPUT VOLTAGE RANGES STANDBY POSITION : REDUCED CONSUMPTION (0.5µA) AND HIGH IMPEDANCE OUTPUTS SINGLE (OR DUAL) SUPPLY OPERATION FROM 2.7V TO 16V (±1.35V to ±8V) . . . . . EXTREMELY LOW INPUT BIAS CURRENT : 1pA TYP LOW INPUT OFFSET VOLTAGE : 5mV max. SPECIFIED FOR 600Ω AND 100Ω LOADS LOW SUPPLY CURRENT : 200µA/Ampli SPEED : 0.7MHz - 0.5V/µs Applies to : TS3V902I,AI ** Standard Linear Ics Macromodels, 1993. ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIV E POWER SUPPLY * 5 NEGATIVE POWER SUPPLY * 6 STANDBY .SUBCKT TS3V902 1 3 2 4 5 6 (analog) ********************************************************** .MODEL MDTH D IS=1E-8 KF=6.563355E-14 CJO=10F * INPUT STAGE CIP 2 5 1.500000E-12 CIN 1 5 1.500000E-12 EIP 10 0 2 0 1 EIN 16 0 1 0 1 RIP 10 11 6.500000E+00 RIN 15 16 6.500000E+00 RIS 11 15 7.655100E+00 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0.000000E+00 VOFN 13 14 DC 0 FPOL 13 0 VSTB 1 CPS 11 15 3.82E-08 DINN 17 13 MDTH 400E-12 VIN 17 5 -0.5000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 -0.5000000E+00 FCP 4 5 VOFP 8.6E+00 FCN 5 4 VOFN 8.6E+00 ISTB0 5 4 900NA * AMPLIFYING STAGE FIP 0 19 VOFP 5.500000E+02 FIN 0 19 VOFN 5.500000E+02 RG1 19 120 5.087344E+05 GCOM1 120 5 POLY(1) 110 109 LEVEL=1 6.25E+11 RG2 121 19 5.087344E+05 GCOM2 121 4 POLY(1) 110 109 LEVEL=1 6.25E+11 CC 19 29 2.200000E-08 HZTP 30 29 VOFP 12.33E+02 HZTN 5 30 VOFN 12.33E+02 8/11 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 3135 VIPM 28 4 150 HONM 21 27 VOUT 3135 VINM 5 27 150 EOUT 26 23 19 5 1 VOUT 23 5 0 ROUT 26 103 65 COUT 103 5 1.000000E-12 GCOM 103 3 POLY(1) 110 109 LEVEL=1 6.25E+11 * OUTPUT SWING DOP 19 68 MDTH 400E-12 VOP 4 25 1.924 HSCP 68 25 VSCP1 1E8 DON 69 19 MDTH 400E-12 VON 24 5 2.4419107 HSCN 24 69 VSCN1 1.5E8 VSCTHP 60 61 0.1375 DSCP1 61 63 MDTH 400E-12 VSCP1 63 64 0 ISCP 64 0 1.000000E-8 DSCP2 0 64 MDTH 400E-12 DSCN2 0 74 MDTH 400E-12 ISCN 74 0 1.000000E-8 VSCN1 73 74 0 DSCN1 71 73 MDTH 400E-12 VSCTHN 71 70 -0.75 ESCP 60 0 2 1 500 ESCN 70 0 2 1 -2000 * STAND BY RMI1 4 111 1E+12 RMI2 5 111 1E+12 RSTBIN 6 0 1E+12 ESTBIN 106 0 6 0 1 ESTBREF 106 107 111 0 1 DSTB1 107 108 MDTH 400E-12 VSTB 108 109 0 ISTB 109 0 40U RSTB 109 110 1 DSTB2 0 110 MDTH 400E-12 .ENDS TS3V902 ELECTRICAL CHARACTERISTICS VCC+ = 5V, VCC- = 0V, RL,CL connected to VCC/2, standby off, Tamb = 25oC (unless otherwise specified) Symbol Vio Avd ICC Vicm VOH VOL Isink Isource GBP SR ∅m ICC STBY RL = 10kΩ RL = 10kΩ VO = 10V VO = 0V RL = 10kΩ, CL = 100pF RL = 10kΩ, CL = 100pF RL = 10kΩ, CL = 100pF VSTBY = 0V RL = 10kΩ No load, per operator Conditions Value 0 30 230 -0.2 to 5.2 4.95 50 60 60 0.8 0.8 30 500 Unit mV V/mV µA V V mV mA mA MHz V/µs Degrees nA 9/11 TS3V902 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP Dimensions a1 B b b1 D E e e3 F i L Z Min. 0.51 1.39 Millimeters Typ. Max. 1.65 Min. 0.020 0.055 Inches Typ. Max. 0.065 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100 DIP14.TBL 10/11 PM-DIP14.EPS TS3V902 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO) Dimensions A a1 a2 b b1 C c1 D E e e3 F G L M S Min. 0.1 0.35 0.19 Millimeters Typ. Max. 1.75 0.2 1.6 0.46 0.25 45o (typ.) Min. 0.004 0.014 0.007 Inches Typ. Max. 0.069 0.008 0.063 0.018 0.010 0.5 8.55 5.8 1.27 7.62 3.8 4.6 0.5 4.0 5.3 1.27 0.68 8 (max.) o 0.020 8.75 6.2 0.336 0.228 0.050 0.300 0.150 0.181 0.020 0.157 0.208 0.050 0.027 0.334 0.244 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. ORDER CODE : © 1997 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved SGS-THOM SON Microelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 11/11 SO14.TBL PM-SO14.EPS