TS420-600B

® TS420 Series 4A SCRs SENSITIVE MAIN FEATURES: Symbol IT(RMS) VDRM/VRRM IGT Value 4 600 and 700 200 Unit A V µA KA G A G A K A DPAK (TS420-B) K A DESCRIPTION Thanks to highly sensitive triggering levels, the TS420 series is suitable for all applications where the available gate current is limited, such as motor control for hand tools, kitchen aids, overvoltage crowbar protection for low power supplies, ... Available in through-hole or surface-mount packages, they provide an optimized performance in a limited space area. A G IPAK (TS420-H) K A G TO-220AB (TS420-T) ABSOLUTE RATINGS (limiting values) Symbol IT(RMS) IT(AV) ITSM Parameter RMS on-state current (180° conduction angle) Average on-state current (180° conduction angle) Non repetitive surge peak on-state current I²t Value for fusing Critical rate of rise of on-state current IG = 2 x IGT , tr ≤ 100 ns Peak gate current Average gate power dissipation Storage junction temperature range Operating junction temperature range tp = 8.3 ms Tj = 25°C tp = 10 ms tp = 10 ms F = 60 Hz tp = 20 µs Tj = 25°C Tj = 125°C Tj = 125°C Tj = 125°C 30 4.5 50 1.2 0.2 - 40 to + 150 - 40 to + 125 A2 S A/µs A W °C Tl = 115°C Tl = 115°C Value 4 2.5 33 A Unit A A I ²t dI/dt IGM PG(AV) Tstg Tj September 2000 - Ed: 3 1/8 TS420 Series ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise specified) Symbol IGT VGT VGD VRG IH IL dV/dt VTM Vt0 Rd IDRM IRRM VD = VDRM IRG = 10 µA IT = 50 mA IG = 1 mA ITM = 8 A RGK = 1 kΩ RGK = 1 kΩ RGK = 220 Ω Tj = 125°C Tj = 25°C Tj = 125°C Tj = 125°C Tj = 25°C Tj = 125°C tp = 380 µs RL = 3.3 kΩ RGK = 220 Ω Tj = 125°C VD = 12 V RL = 33 Ω Test Conditions MAX. MAX. MIN. MIN. MAX. MAX. MIN. MAX. MAX. MAX. MAX. TS420 200 0.8 0.1 8 5 6 5 1.6 0.85 90 5 1 Unit µA V V V mA mA V/µs V V mΩ µA mA VD = 67 % VDRM Threshold voltage Dynamic resistance VDRM = VRRM RGK = 220 Ω THERMAL RESISTANCES Symbol Rth(j-c) Rth(j-a) Junction to case (DC) Junction to ambient (DC) S = 0.5 cm² DPAK IPAK TO-220AB S = copper surface under tab Parameter Value 3.0 70 100 60 Unit °C/W °C/W PRODUCT SELECTOR Voltage (xxx) Part Number 600 V TS420-xxxB TS420-xxxH TS420-xxxT X X X 700 V X X X 200 µA 200 µA 200 µA DPAK IPAK TO-220AB Sensitivity Package ORDERING INFORMATION SCR SERIES PACKAGE: B: DPAK H: IPAK T: TO-220AB CURRENT: 4A SENSITIVITY: 20: 200µA VOLTAGE: 600: 600V 700: 700V PACKING MODE Blank: Tube -TR: DPAK tape & reel 2/8 TS420 Series OTHER INFORMATION Part Number TS420-x00B TS420-x00B-TR TS420-x00H TS420-x00T Note: x = voltage Marking TS420x00 TS420x00 TS420x00 TS420x00T Weight 0.3 g 0.3 g 0.4 g 2.3 g Base Quantity 75 2500 75 50 Packing mode Tube Tape & reel Tube Tube Fig. 1: Maximum average power dissipation versus average on-state current. P(W) 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.0 0.5 1.0 IT(av)(A) 1.5 2.0 α 360° Fig. 2-1: Average and D.C. on-state current versus case temperature. IT(av)(A) 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 α = 180° DC α = 180° Tcase(°C) 0 25 50 75 100 125 2.5 3.0 Fig. 2-2: Average and D.C. on-state current versus ambient temperature (device mounted on FR4 with recommended pad layout) (DPAK). IT(av)(A) 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 Fig. 3: Relative variation of thermal impedance junction to ambient versus pulse duration (recommended pad layout, FR4 PC board) for DPAK. DC α = 180° DPAK (S = 0.5cm 2) IPAK DC α = 180° Tamb(°C) 0 25 50 75 100 125 3/8 TS420 Series Fig. 4: Relative variation of gate trigger current and holding current versus junction temperature. IGT,IH,IL [Tj] / IGT ,IH,IL [Tj = 25 °C] 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -40 Fig. 5: R elative variation of holding current versus gate-cathode resistance (typical values). IH[Rgk] / IH[Rgk = 1kΩ] IGT IH & IL Rgk = 1k Ω Tj(°C) -20 0 20 40 60 80 100 120 140 Rgk(kΩ) Fig. 6: Relative variation of dV/dt immunity versus gate-cathode resistance (typical values). dV/dt[Rgk] / dV/dt [Rgk = 220Ω] 10.00 Tj=125°C VD=0.67xVDRM Fig. 7: Relative variation of dV/dt immunity versus gate-cathode resistance (typical values). dV/dt[Cgk] / dV/dt [Rgk = 220 Ω] 10 8 VD = 0.67 x VDRM Tj = 125°C Rgk = 220 Ω 1.00 6 4 0.10 2 Rgk(Ω) Cgk(nF) 0 1.2 1.4 1.6 1.8 2.0 0.01 0 0.2 0.4 0.6 0.8 1.0 0 2 4 6 8 10 12 14 16 18 20 22 Fig. 8: Surge peak on-state current versus number of cycles. Fig. 9: Non-repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms, and corresponding values of I²t. ITSM(A),I 2t(A2s) 300 Tj initial = 25 °C dI/dt limitattion ITSM ITSM(A) 35 30 25 20 15 10 5 0 1 Repetitive Tcase = 115 °C Non repetitiv e Tj initial = 25 °C tp = 10ms One cycle 100 10 I2t Number of cycles 10 100 1000 tp(ms) 1 0.01 0.10 1.00 10.00 4/8 TS420 Series Fig. 10: On-state characteristics (maximum values). Fig. 11: Thermal resistance junction to ambient versus copper surface under tab (Epoxy printed circuit board FR4, copper thickness: 35 µm) (DPAK). Rth(j-a) ( °C/W) 100 ITM(A) 50.0 Tj max.: Vto = 0.85V Rd = 90m Ω 10.0 Tj = Tj max. 80 60 40 Tj = 25°C 1.0 20 0.1 0.0 VTM(V) 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 S(cm 2) 0 0 2 4 6 8 10 12 14 16 18 20 5/8 TS420 Series PACKAGE MECHANICAL DATA DPAK (Plastic) DIMENSIONS REF. Millimeters Min. A A1 A2 B B2 C C2 D E G H L2 L4 R V2 Max Min. Inches Max. R R 2.20 2.40 0.90 1.10 0.03 0.23 0.64 0.90 5.20 5.40 0.45 0.60 0.48 0.60 6.00 6.20 6.40 6.60 4.40 4.60 9.35 10.10 0.80 typ. 0.60 1.00 0.2 typ. 0° 8° 0.086 0.094 0.035 0.043 0.001 0.009 0.025 0.035 0.204 0.212 0.017 0.023 0.018 0.023 0.236 0.244 0.251 0.259 0.173 0.181 0.368 0.397 0.031 typ. 0.023 0.039 0.007 typ. 0° 8° FOOTPRINT DIMENSIONS (in millimeters) DPAK (Plastic) 6.7 6.7 3 3 1.6 2.3 2.3 1.6 6/8 TS420 Series PACKAGE MECHANICAL DATA IPAK (Plastic) DIMENSIONS REF. Millimeters Min. A E B2 L2 C2 Inches Min. 0.086 0.035 0.027 0.025 0.204 0.035 Typ. Max. 0.094 0.043 0.051 0.035 0.212 0.033 0.037 0.023 0.023 0.244 0.260 0.181 0.641 0.370 0.047 0.031 0.039 10° Typ. Max. 2.4 1.1 1.3 0.9 5.4 0.85 D H L L1 B6 B3 B V1 A1 B5 G C A3 A A1 A3 B B2 B3 B5 B6 C C2 D E G H L L1 L2 V1 2.2 0.9 0.7 0.64 5.2 0.3 0.45 0.48 6 6.4 4.4 15.9 9 0.8 0.8 10° 0.95 0.6 0.6 6.2 6.6 4.6 16.3 9.4 1.2 1 0.017 0.019 0.236 0.252 0.173 0.626 0.354 0.031 7/8 TS420 Series PACKAGE MECHANICAL DATA TO-220AB (Plastic) DIMENSIONS REF. H2 Dia L5 C L7 L6 L2 F2 F1 L9 L4 F G1 G M E D A Millimeters Min. Max. Min. Inches Max. A C D E F F1 F2 G G1 H2 L2 L4 L5 L6 L7 L9 M Diam. 4.40 4.60 1.23 1.32 2.40 2.72 0.49 0.70 0.61 0.88 1.14 1.70 1.14 1.70 4.95 5.15 2.40 2.70 10 10.40 16.4 typ. 13 14 2.65 2.95 15.25 15.75 6.20 6.60 3.50 3.93 2.6 typ. 3.75 3.85 0.173 0.181 0.048 0.051 0.094 0.107 0.019 0.027 0.024 0.034 0.044 0.066 0.044 0.066 0.194 0.202 0.094 0.106 0.393 0.409 0.645 typ. 0.511 0.551 0.104 0.116 0.600 0.620 0.244 0.259 0.137 0.154 0.102 typ. 0.147 0.151 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2000 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom http://www.st.com 8/8