TS882
TS884
Rail-to-rail 1.1 V dual and quad nanopower comparators
Datasheet - production data
Related product
• See the TS881 datasheet for single operator
with smaller package.
DFN8 (2 x 2 mm)
MiniSO8
Applications
• Portable systems
• Signal conditioning
TSSOP14
SO14
• Medical
• Automotive
QFN16 (3 x 3 mm)
Description
Features
• Ultra-low current consumption: 220 nA typ./op.
• Propagation delay: 2 µs typ.
• Rail-to-rail inputs
• Push-pull outputs
• Supply operation from 1.1 V to 5.5 V
• Wide temperature range: -40 to +125 °C
• ESD tolerance: 8 kV HBM / 300 V MM
• Dual version available in MiniSO8 and DFN8
(2 x 2 mm) package
The TS882 is a dual and the TS884 device a
quad comparator featuring ultra-low supply
current (220 nA typical per operator with output
high, VCC = 1.2 V, no load) with rail-to-rail input
and output capability. The performance of these
comparators allows them to be used in a wide
range of portable applications. The TS882 and
TS884 devices minimize battery supply leakage
and therefore enhance battery lifetime.
Operating from 1.1 to 5.5 V supply voltage, these
comparators can be used over a wide
temperature range (-40 to +125 °C) keeping the
current consumption at an ultra-low level.
• Quad version available in SO14, TSSOP14
and QFN16 3 x 3 mm package
Table 1. Device summary
Order code
Temperature range
TS882IST
TS882IYST(1)
Package
Packaging
MiniSO8
-40 to +125 °C
MiniSO8
(Automotive grade)
Marking
K514
Tape and reel
K524
TS882IQ2T
DFN8 2 x 2 mm
K56
TS884IDT
SO14
S884I
TS884IPT
-40 to +125 °C
TS884IQ4T
TSSOP14
QFN16 3 x 3 mm
Tape and reel
S884I
K514
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001
& Q002 or equivalent
July 2017
This is information on a product in full production.
DocID024119 Rev 4
1/25
www.st.com
Contents
TS882, TS884
Contents
1
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . 5
4
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5
2/25
4.1
DFN8 2 x 2 mm package information
. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.2
MiniSO8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.3
SO14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.4
QFN16 3 x 3 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.5
TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DocID024119 Rev 4
TS882, TS884
1
Pin description
Pin description
Figure 1. Pin connections TS882 (top view)
TS882IDT/IST/IQ2T
MiniSO8/DFN8
Figure 2. Pin connections TS884 (top view)
SO14 / TSSOP14
287 287
,1
,1
,1
,1
9&&
9&&
1&
1&
,1
,1
,1
,1
287 287
QFN16
DocID024119 Rev 4
3/25
25
Absolute maximum ratings and operating conditions
2
TS882, TS884
Absolute maximum ratings and operating conditions
Table 2. Absolute maximum ratings
Symbol
VCC
Parameter
Value
Unit
6
V
±6
V
(VCC-) - 0.3 to (VCC+) + 0.3
V
Supply voltage(1)
VID
Differential input voltage
VIN
Input voltage range
(2)
Thermal resistance junction to ambient (TS882)(3)
MiniSO8
DFN8 2 x 2 mm
RTHJA
190
57
Thermal resistance junction to ambient (TS884)(3)
SO14
TSSOP14
QFN16 3 x 3 mm
°C/W
105
100
45
TSTG
Storage temperature
-65 to +150
°C
TJ
Junction temperature
150
°C
260
°C
8
kV
TLEAD
Lead temperature (soldering 10 seconds)
(4)
Human body model (HBM)
ESD
Machine model
(MM)(5)
300
V
Charged device model (CDM)(6)
1300
Latch-up immunity
200
mA
1. All voltage values, except differential voltages, are referenced to VCC-. VCC is defined as the difference
between VCC+ and VCC-.
2. The magnitude of input and output voltages must never exceed the supply rail ±0.3 V.
3. Short-circuits can cause excessive heating. These values are typical.
4. According to JEDEC standard JESD22-A114F.
5. According to JEDEC standard JESD22-A115A.
6. According to ANSI/ESD STM5.3.1.
Table 3. Operating conditions
Symbol
4/25
Parameter
Toper
Operating temperature range
VCC
Supply voltage
-40 °C < Tamb < +125 °C
VICM
Common mode input voltage range
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
DocID024119 Rev 4
Value
Unit
-40 to +125
°C
1.1 to 5.5
(VCC-) - 0.2 to (VCC+) + 0.2
(VCC-) to (VCC+) + 0.2
V
V
TS882, TS884
3
Electrical characteristics
Electrical characteristics
Table 4. VCC = +1.2 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1)
Symbol
Parameter
Test conditions
Input offset voltage(2)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
Input offset voltage drift
-40 °C < Tamb < +125 °C
Input hysteresis voltage(3)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
IIO
Input offset current(4)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
IIB
Input bias current(4)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
VIO
ΔVIO
VHYST
ICC
6
3
4.2
1
220
1.0
1.7
Isource = 0.2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
VOL
Output voltage low
Isink = 0.2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
Common mode rejection ratio
0 < VICM < VCC
-40 °C < Tamb < +125 °C
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
Propagation delay
(high to low)
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
Rise time (10% to 90%)
mV
mV
10
100
pA
10
100
pA
450
nA
Output voltage high
Propagation delay
(low to high)
Unit
µV/°C
2.4
1.5
No load, output high, VID = +0.1 V
-40 °C < Tamb < +125 °C
VOH
TR
-6
Supply current per operator
Source
Sink
TPHL
Max.
1
300
Short-circuit current
TPLH
Typ.
No load, output low, VID = -0.1 V
-40 °C < Tamb < +125 °C
ISC
CMRR
Min.
CL = 30 pF, RL = 1 MΩ
DocID024119 Rev 4
350
1.13
1.10
1.00
mA
1.15
V
35
50
60
70
68
dB
50
5.5
11
13
2.1
3.1
3.4
5.1
8
10
1.9
100
mV
µs
µs
2.6
3.1
ns
5/25
25
Electrical characteristics
TS882, TS884
Table 4. VCC = +1.2 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1) (continued)
Symbol
TF
TON
Parameter
Fall time (90% to 10%)
Test conditions
Min.
CL = 30 pF, RL = 1 MΩ
Typ.
Max.
110
Power-up time
1.1
Unit
ns
1.7
ms
1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed
at the temperature range limits.
2. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to
change the output state in each direction).
3. The hysteresis is a built-in feature of the TS882 device. It is defined as the voltage difference between the trip points.
4. Maximum values include unavoidable inaccuracies of the industrial tests.
Table 5. VCC = +2.7 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1)
Symbol
Parameter
Test conditions
Input offset voltage(2)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
Input offset voltage drift
-40 °C < Tamb < +125 °C
Input hysteresis voltage(3)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
IIO
Input offset current(4)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
IIB
Input bias current(4)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
VIO
ΔVIO
VHYST
ICC
-6
6
3
2.7
1.6
4.2
1
No load, output high, VID = +0.1 V
-40 °C < Tamb < +125 °C
220
10
13
mV
mV
10
100
pA
10
100
pA
450
nA
VOH
Output voltage high
Isource = 2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
VOL
Output voltage low
Isink = 2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
Common mode rejection ratio
0 < VICM < VCC
-40 °C < Tamb < +125 °C
Propagation delay
(low to high)
Unit
µV/°C
Supply current per operator
Source
Sink
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
6/25
Max.
1
310
Short-circuit current
TPLH
Typ.
No load, output low, VID = -0.1 V
-40 °C < Tamb < +125 °C
ISC
CMRR
Min.
DocID024119 Rev 4
350
2.48
2.40
2.10
mA
2.51
V
130
210
230
310
74
dB
55
6.4
2.3
mV
12
14
3.0
3.7
µs
TS882, TS884
Electrical characteristics
Table 5. VCC = +2.7 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1) (continued)
Symbol
TPHL
Parameter
Propagation delay
(high to low)
Test conditions
Min.
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
Typ.
Max.
6.4
12
14
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
2.2
Unit
µs
3.0
3.7
TR
Rise time (10% to 90%)
CL = 30 pF, RL = 1 MΩ
120
ns
TF
Fall time (90% to 10%)
CL = 30 pF, RL = 1 MΩ
130
ns
TON
Power-up time
1.1
1.7
ms
1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed
at the temperature range limits.
2. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to
change the output state in each direction).
3. The hysteresis is a built-in feature of the TS882. It is defined as the voltage difference between the trip points.
4. Maximum values include unavoidable inaccuracies of the industrial tests.
Table 6. VCC = +5 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1)
Symbol
Parameter
Test conditions
Input offset voltage(2)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
Input offset voltage drift
-40 °C < Tamb < +125 °C
Input hysteresis voltage(3)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
IIO
Input offset current(4)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
IIB
Input bias current(4)
Tamb = +25 °C
-40 °C < Tamb < +125 °C
VIO
ΔVIO
VHYST
ICC
Typ.
Max.
1
-6
6
3
4.2
1
350
No load, output high, VID = +0.1 V
-40 °C < Tamb < +125 °C
250
32
32
Unit
mV
µV/°C
3.1
1.6
No load, output low, VID = -0.1 V
-40 °C < Tamb < +125 °C
mV
10
100
pA
10
100
pA
500
Supply current per operator
nA
ISC
Short-circuit current
Source
Sink
VOH
Output voltage high
Isource = 2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
VOL
Output voltage low
Isink = 2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
Common mode rejection ratio
0 < VICM < VCC
-40 °C < Tamb < +125 °C
CMRR
Min.
DocID024119 Rev 4
400
4.86
4.75
4.60
4.88
V
90
78
55
mA
130
170
280
mV
dB
7/25
25
Electrical characteristics
TS882, TS884
Table 6. VCC = +5 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1) (continued)
Symbol
SVR
TPLH
Parameter
Supply voltage rejection
Propagation delay
(low to high)
Test conditions
ΔVCC = 1.2 V to 5 V
-40 °C < Tamb < +125 °C
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
TPHL
Propagation delay
(high to low)
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
Min.
Typ.
Max.
80
dB
65
8.3
13
22
2.5
3.4
4.1
9.0
16
19
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
2.6
Unit
µs
µs
3.5
4.2
TR
Rise time (10% to 90%)
CL = 30 pF, RL = 1 MΩ
160
ns
TF
Fall time (90% to 10%)
CL = 30 pF, RL = 1 MΩ
150
ns
TON
Power-up time
1.1
1.7
ms
1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed
at the temperature range limits.
2. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to
change the output state in each direction).
3. The hysteresis is a built-in feature of the TS882 device. It is defined as the voltage difference between the trip points.
4. Maximum values include unavoidable inaccuracies of the industrial tests.
8/25
DocID024119 Rev 4
TS882, TS884
Electrical characteristics
Figure 3. Current consumption per operator vs. Figure 4. Current consumption per operator vs.
supply voltage - output low
supply voltage - output high
Figure 5. Current consumption per operator vs. Figure 6. Current consumption per operator vs.
input common mode voltage at VCC = 1.2 V
input common mode voltage at VCC = 5 V
Figure 7. Current consumption per operator vs. Figure 8. Current consumption per operator vs.
temperature
toggle frequency
DocID024119 Rev 4
9/25
25
Electrical characteristics
TS882, TS884
Figure 9. Input offset voltage vs. input common
mode voltage at VCC = 1.2 V
Figure 10. Input hysteresis voltage vs. input
common mode voltage at VCC = 1.2 V
Figure 11. Input offset voltage vs. input
common mode voltage at VCC = 5 V
Figure 12. Input hysteresis voltage vs. input
common mode voltage at VCC = 5 V
Figure 13. Input offset voltage vs. temperature
Figure 14. Input hysteresis voltage vs.
temperature
10/25
DocID024119 Rev 4
TS882, TS884
Electrical characteristics
Figure 15. Output voltage drop vs. sink current
at VCC = 1.2 V
Figure 16. Output voltage drop vs. source
current at VCC = 1.2 V
Figure 17. Output voltage drop vs. sink current
at VCC = 2.7 V
Figure 18. Output voltage drop vs. source
current at VCC = 2.7 V
Figure 19. Output voltage drop vs. sink current
at VCC = 5 V
Figure 20. Output voltage drop vs. source
current at VCC = 5 V
DocID024119 Rev 4
11/25
25
Electrical characteristics
TS882, TS884
Figure 21. Propagation delay TPLH vs. input
common mode voltage at VCC = 1.2 V
Figure 22. Propagation delay TPLH vs. input
common mode voltage at VCC = 1.2 V
Figure 23. Propagation delay TPLH vs. input
common mode voltage at VCC = 5 V
Figure 24. Propagation delay TPHL vs. input
common mode voltage at VCC = 5 V
Figure 25. Propagation delay TPLH vs. input
signal overdrive at VCC = 1.2 V
Figure 26. Propagation delay TPHL vs. input
signal overdrive at VCC = 1.2 V
12/25
DocID024119 Rev 4
TS882, TS884
Electrical characteristics
Figure 27. Propagation delay TPLH vs. input
signal overdrive at VCC = 5 V
Figure 28. Propagation delay TPHL vs. input
signal overdrive at VCC = 5 V
Figure 29. Propagation delay TPLH vs. supply
voltage for signal overdrive 10 mV
Figure 30. Propagation delay TPHL vs. supply
voltage for signal overdrive 10 mV
Figure 31. Propagation delay TPLH vs. supply
voltage for signal overdrive 100 mV
Figure 32. Propagation delay TPHL vs. supply
voltage for signal overdrive 100 mV
DocID024119 Rev 4
13/25
25
Electrical characteristics
TS882, TS884
Figure 33. Propagation delay vs. temperature
for signal overdrive 10 mV
14/25
Figure 34. Propagation delay vs. temperature
for signal overdrive 100 mV
DocID024119 Rev 4
TS882, TS884
4
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
DocID024119 Rev 4
15/25
25
Package information
4.1
TS882, TS884
DFN8 2 x 2 mm package information
Figure 35. DFN8 2 x 2 mm package outline
4&"5*/( $
1-"/&
EEE
"
"
$
"
%
F
1*/*%
&
&
C
%
Table 7. DFN8 2 x 2 mm package mechanical data (pitch 0.5 mm)
Dimensions
Symbol
A
Millimeters
Min.
Typ.
Max.
Min.
Typ.
Max.
0.51
0.55
0.60
0.020
0.022
0.024
A1
0.05
A3
0.002
0.15
0.006
b
0.18
0.25
0.30
0.007
0.010
0.012
D
1.85
2.00
2.15
0.073
0.079
0.085
D2
1.45
1.60
1.70
0.057
0.063
0.067
E
1.85
2.00
2.15
0.073
0.079
0.085
E2
0.75
0.90
1.00
0.030
0.035
0.039
e
16/25
Inches
0.50
0.020
L
0.50
0.020
ddd
0.08
0.003
DocID024119 Rev 4
TS882, TS884
Package information
Figure 36. DFN8 2 x 2 mm footprint recommendation
PP
PP
PP
PP
PP
DocID024119 Rev 4
PP
17/25
25
Package information
4.2
TS882, TS884
MiniSO8 package information
Figure 37. MiniSO8 package outline
Table 8. MiniSO8 package mechanical data
Dimensions
Symbol
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.10
A1
0
A2
0.75
b
Max.
0.043
0.15
0
0.95
0.030
0.22
0.40
0.009
0.016
c
0.08
0.23
0.003
0.009
D
2.80
3.00
3.20
0.11
0.118
0.126
E
4.65
4.90
5.15
0.183
0.193
0.203
E1
2.80
3.00
3.10
0.11
0.118
0.122
e
L
0.85
0.65
0.40
0.60
0.006
0.033
0.80
0.016
0.024
0.95
0.037
L2
0.25
0.010
ccc
0°
0.037
0.026
L1
k
18/25
Inches
8°
0.10
DocID024119 Rev 4
0°
0.031
8°
0.004
TS882, TS884
4.3
Package information
SO14 package information
Figure 38. SO14 package outline
Table 9. SO14 package mechanical data
Dimensions(1)
Millimeters
Inches
Symbol
Note
Min.
Typ.
Max.
Min.
Typ.
Max.
A
1.35
1.75
0.05
0.068
A1
0.10
0.25
0.004
0.009
A2
1.10
1.65
0.04
0.06
B
0.33
0.51
0.01
0.02
C
0.19
0.25
0.007
0.009
D
8.55
8.75
0.33
0.34
E
3.80
4.0
0.15
0.15
e
1.27
0.05
H
5.80
6.20
0.22
0.24
L
0.40
1.27
0.015
0.05
k
0°
8°
0°
8°
ddd
(2)
0.10
0.004
1. Drawing dimensions include “Single” and “Matrix” versions.
2. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs
shall not exceed 0.15 mm per side.
DocID024119 Rev 4
19/25
25
Package information
4.4
TS882, TS884
QFN16 3 x 3 package information
Figure 39. QFN16 3 x 3 mm (pitch 0.5 mm) package outline
6($7,1*
3/$1(
&
GGG&
$
$
$
'
3,1,'
&
'
H
H
(
E
/
E
/
'
%277209,(:
20/25
DocID024119 Rev 4
(
(
TS882, TS884
Package information
Table 10. QFN16 3 x 3 mm (pitch 0.5 mm) package mechanical data
Dimensions
Symbol
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
0.80
0.90
1.00
0.031
0.035
0.039
A1
0.02
0.05
0.001
0.002
A3
0.20
A
0.008
b
0.18
0.25
0.30
0.007
0.010
0.012
D
2.85
3.00
3.15
0.112
0.118
0.124
D1
1.50
0.059
D2
See exposed pad variation
See exposed pad variation
E
2.85
3.00
3.15
0.112
0.118
0.124
E1
1.50
0.059
E2
See exposed pad variation
See exposed pad variation
e
0.45
0.50
0.55
0.018
0.020
0.022
L
0.30
0.40
0.50
0.012
0.016
0.020
ddd
0.08
DocID024119 Rev 4
0.003
21/25
25
Package information
TS882, TS884
Figure 40. QFN16 3 x 3 mm (pitch 0.5 mm) footprint recommendation
%
22/25
DocID024119 Rev 4
$
TS882, TS884
4.5
Package information
TSSOP14 package information
Figure 41. TSSOP14 package outline
'
(
$ $ $
DDD&
E
F
6($7,1*
3/$1(
PP
*$*(3/$1(
&
(
N
3,1,'(17,),&$7,21
/
/
H
76623
Table 11. TSSOP14 package mechanical data
Dimensions
Symbol
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.20
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.90
5.00
5.10
0.193
0.197
0.201
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.176
e
L
0.65
0.45
L1
k
aaa
1.00
0.60
0.0256
0.75
0.018
1.00
0°
0.024
0.030
0.039
8°
0.10
DocID024119 Rev 4
0°
8°
0.004
23/25
25
Revision history
5
TS882, TS884
Revision history
Table 12. Document revision history
24/25
Date
Revision
Changes
18-Jan-2013
1
Initial release.
02-May-2013
2
Added TS884 device to header, Description, and Table 1: Device
summary.
Updated title (added “quad” comparator).
Updated Features and Table 2 (ESD tolerance: “6 kV” HBM replaced
by “8 kV” HBM).
Updated Description in accordance with added TS884 device.
Added SO14, TSSOP14 and QFN16 3 x 3 mm package to Features,
figure on page 1, Section 4: Package information. and Table 1:
Device summary.
Moved Figure 1: Pin connections TS882 (top view) to page 3.
Added Figure 2: Pin connections TS884 (top view).
Updated Table 2: Absolute maximum ratings (added TS884 device
RTHJA values).
Minor corrections throughout document.
14-Jul-2014
3
Updated Table 1: Device summary on page 1.
06-Jul-2017
4
Added order code TS882IYST in Table 1: Device summary and
“Automotive” in Applications.
DocID024119 Rev 4
TS882, TS884
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2017 STMicroelectronics – All rights reserved
DocID024119 Rev 4
25/25
25