TS924AIPT

TS924 Rail-to-rail high output current quad operational amplifier Features ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Rail-to-rail input and output Low noise: 9 nV/√Hz Low distortion High output current: 80 mA (able to drive 32 Ω loads) High-speed: 4 MHz, 1.3 V/µs Operating range from 2.7 V to 12 V Low input offset voltage: 900 µV max (TS924A) ESD internal protection: 3 kV Latch-up immunity Macromodel included in this specification P TSSOP14 (Thin shrink small outline package) D SO-14 (Plastic micropackage) N DIP14 (Plastic package) Applications ■ ■ ■ ■ ■ ■ ■ Headphone amplifier Piezoelectric speaker driver Sound cards MPEG boards, multimedia systems Line driver, buffer Cordless telephones and portable communication equipment Instrumentation with low noise as key factor Pin connections (top view) Output 1 1 Inverting Input 1 2 Non-inverting Input 1 3 VCC + 4 Non-inverting Input 2 5 Inverting Input 2 6 Output 2 7 + + + + 14 Output 4 13 Inverting Input 4 12 Non-inverting Input 4 11 VCC 10 Non-inverting Input 3 9 8 Inverting Input 3 Output 3 Description The TS924 is a rail-to-rail quad BiCMOS operational amplifier optimized and fully specified for 3 V and 5 V operation. High output current allows low load impedances to be driven. The TS924 exhibits a very low noise, low distortion, low offset and high output current capability making this device an excellent choice for high quality, low voltage or battery operated audio systems. The device is stable for capacitive loads up to 500 pF. March 2008 Rev 5 1/14 www.st.com 14 Absolute maximum ratings and operating conditions TS924 1 Absolute maximum ratings and operating conditions Table 1. Symbol VCC Vid Vin Tstg Tj Supply voltage (1) Differential input voltage Input voltage (3) (2) Absolute maximum ratings Parameter Value 14 ±1 VDD -0.3 to VCC+0.3 -65 to +150 150 103 66 100 3 100 (7) Unit V V V °C °C Storage temperature Maximum junction temperature Thermal resistance junction to DIP14 SO-14 TSSOP14 HBM: human body model(5) ambient(4) Rthja °C/W kV V kV (8) ESD MM: machine model(6) CDM: charged device model Output short-circuit duration Latch-up immunity 1 see note 200 250 260 mA °C °C Soldering temperature (10 sec), leaded version Soldering temperature (10 sec), unleaded version 1. All voltage values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. If Vid > ±1 V, the maximum input current must not exceed ±1 mA. In this case (Vid > ±1 V), an input series resistor must be added to limit input current. 3. Do not exceed 14 V. 4. Short-circuits can cause excessive heating and destructive dissipation. Rth are typical values. 5. Human body model: A 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating. 6. Machine model: A 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of connected pin combinations while the other pins are floating. 7. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly to the ground through only one pin. This is done for all pins. 8. There is no short-circuit protection inside the device: short-circuits from the output to VCC can cause excessive heating. The maximum output current is approximately 80 mA, independent of the magnitude of VCC. Destructive dissipation can result from simultaneous short-circuits on all amplifiers. Table 2. Symbol VCC Vicm Toper Operating conditions Parameter Supply voltage Common mode input voltage range Operating free air temperature range Value 2.7 to 12 VDD -0.2 to VCC +0.2 -40 to +125 Unit V V °C 2/14 TS924 Electrical characteristics 2 Electrical characteristics Table 3. Electrical characteristics at VCC = +3V with VDD = 0V, Vicm = VCC/2, Tamb = 25°C, and RL connected to VCC/2 (unless otherwise specified) Parameter Input offset voltage TS924 TS924A Tmin ≤ Tamb ≤ Tmax TS924 TS924A Input offset voltage drift Input offset current - Vout = VCC/2 Input bias current - Vout = VCC/2 High level output voltage RL= 10kΩ RL = 600Ω RL = 32Ω Low level output voltage RL= 10kΩ RL = 600Ω RL = 32Ω Large signal voltage gain (Vout = 2Vpk-pk) RL= 10kΩ RL = 600Ω RL = 32Ω Total supply current - no load, Vout = VCC/2 Gain bandwidth product - RL = 600Ω Common mode rejection ratio Supply voltage rejection ratio - VCC = 2.7 to 3.3V Output short-circuit current Slew rate Phase margin at unit gain - RL = 600Ω, CL =100pF Gain margin - RL = 600Ω, CL =100pF Equivalent input noise voltage - f = 1kHz Total harmonic distortion Vout = 2Vpk-pk, F = 1kHz, Av = 1, RL =600Ω Channel separation 60 60 50 0.7 2.90 2.87 2.63 50 100 180 200 35 16 4.5 4 80 85 80 1.3 68 12 9 0.005 120 7 2 1 15 30 100 Min. Typ. Max. Unit Symbol Vio 3 0.9 5 1.8 mV DVio Iio Iib µV/°C nA nA VOH V VOL mV Avd V/mV ICC GBP CMR SVR Io SR φm Gm en THD Cs mA MHz dB dB mA V/µs Degrees dB nV ----------Hz % dB 3/14 Electrical characteristics Table 4. Symbol Input offset voltage TS924 TS924A Tmin ≤ Tamb ≤ Tmax TS924 TS924A Input offset voltage drift Input offset current - Vout = VCC/2 Input bias current - Vout = VCC/2 High level output voltage RL= 10kΩ RL = 600Ω RL = 32Ω Low level output voltage RL= 10kΩ RL = 600Ω RL = 32Ω Large signal voltage gain (Vout = 2Vpk-pk) RL= 10kΩ RL = 600Ω RL = 32Ω Total supply current - no load, Vout = VCC/2 Gain bandwidth product - RL = 600Ω Common mode rejection ratio Supply voltage rejection ratio - VCC = 3V to 5V Output short-circuit current Slew rate Phase margin at unit gain - RL = 600Ω, CL =100pF Gain margin -RL = 600Ω, CL =100pF Equivalent input noise voltage - f = 1kHz Total harmonic distortion Vout = 2Vpk-pk, F = 1kHz, Av = 1, RL =600Ω Channel separation 60 60 50 0.7 4.90 4.85 4.4 50 120 300 200 40 17 4.5 4 80 85 80 1.3 68 12 9 0.005 120 7 2 1 15 30 100 TS924 VCC = +5V, VDD = 0V, Vicm = VCC/2, Tamb = 25°C, RL connected to VCC/2 (unless otherwise specified) Parameter Min. Typ. Max. Unit Vio 3 0.9 5 1.8 mV DVio Iio Iib µV/°C nA nA VOH V VOL mV Avd V/mV ICC GBP CMR SVR Io SR φm Gm en THD Cs mA MHz dB dB mA V/µs Degrees dB nV ----------Hz % dB 4/14 TS924 Electrical characteristics Figure 1. 100 Output short circuit current vs. output voltage Figure 2. Output short circuit current vs. output voltage 100 80 80 Output Short-Circuit Current (mA) 60 Output Short-Circuit Current (mA) Sink 40 60 40 20 0 -20 -40 -60 -80 Sink Vcc=0/12V 20 0 -20 -40 -60 -80 -100 0 2 4 6 8 10 12 Vcc=0/3V Source Source -100 0 0,5 1 1,5 2 2,5 3 Output Voltage (V) Output Voltage (V) Figure 3. Voltage gain and phase vs. frequency Figure 4. 100 80 Output short circuit current vs. output voltage Output Short-Circuit Current (mA) CL=500pF VCC=±1.5V 60 40 20 0 -20 -40 -60 -80 -100 0 1 Sink Phase Vcc=0/5V Gain Source 2 3 4 5 Output Voltage (V) Figure 5. Voltage gain and phase vs. frequency RL=10κ CL=100pF VCC=±1.5V Figure 6. THD + noise vs. frequency RL=2k Vo=10Vpp VCC=±6V Av= -1 Phase Gain 5/14 Electrical characteristics TS924 Figure 7. THD + noise vs. frequency Figure 8. THD + noise vs. frequency RL=2k Vo=10Vpp VCC=±6V Av= 1 RL=32Ω Vo=2Vpp VCC=±1.5V Av= 10 Figure 9. THD + noise vs. Vout Figure 10. THD + noise vs. frequency RL=32Ω f=1kHz VCC=±1.5V Av= -1 RL=32Ω Vo=4Vpp VCC=±2.5V Av= 1 Figure 11. THD + noise vs. Vout Figure 12. THD + noise vs. Vout RL=2kΩ f=1kHz VCC=±1.5V Av= -1 6/14 TS924 Macromodel 3 3.1 Macromodel Important note concerning this macromodel Please consider the following remarks before using this macromodel. ● ● ● All models are a trade-off between accuracy and complexity (i.e. simulation time). Macromodels are not a substitute to breadboarding; rather, they confirm the validity of a design approach and help to select surrounding component values. A macromodel emulates the nominal performance of a typical device within specified operating conditions (temperature, supply voltage, for example). Thus the macromodel is often not as exhaustive as the datasheet, its purpose is to illustrate the main parameters of the product. Data derived from macromodels used outside of the specified conditions (VCC, temperature, for example) or even worse, outside of the device operating conditions (VCC, Vicm, for example), is not reliable in any way. Section 3.2 presents the electrical characteristics resulting from the use of these macromodels. 3.2 Electrical characteristics from macromodelization Table 5. Symbol Vio Avd ICC Vicm VOH VOL Isink Isource GBP SR φm RL = 10kΩ RL = 10kΩ VO = 3V VO = 0V RL = 600kΩ , RL = 10kΩ CL = 100pF RL = 600kΩ RL = 10kΩ No load, per operator Macromodel simulation at VCC = 3V, VDD = 0V, RL, CL connected to VCC/2, and Tamb = 25°C (unless otherwise specified) Conditions Value 0 200 1.2 -0.2 to 3.2 2.95 25 80 80 4 1 68 Unit mV V/mV mA V V mV mA mA MHz V/µs Degrees 7/14 Macromodel TS924 3.3 Macromodel code ** Standard Linear Ics Macromodels, 1996. ** CONNECTIONS: * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT TS92X 1 2 3 4 5 * .MODEL MDTH D IS=1E-8 KF=2.664234E-16 CJO=10F * * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 8.125000E+00 RIN 15 16 8.125000E+00 RIS 11 15 2.238465E+02 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 153.5u VOFN 13 14 DC 0 IPOL 13 5 3.200000E-05 CPS 11 15 1e-9 DINN 17 13 MDTH 400E-12 VIN 17 5 -0.100000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 0.400000E+00 FCP 4 5 VOFP 1.865000E+02 FCN 5 4 VOFN 1.865000E+02 FIBP 2 5 VOFP 6.250000E-03 FIBN 5 1 VOFN 6.250000E-03 * GM1 STAGE *************** FGM1P 119 5 VOFP 1.1 FGM1N 119 5 VOFN 1.1 RAP 119 4 2.6E+06 RAN 119 5 2.6E+06 * GM2 STAGE *************** G2P 19 5 119 5 1.92E-02 G2N 19 5 119 4 1.92E-02 R2P 19 4 1E+07 R2N 19 5 1E+07 ************************** VINT1 500 0 5 GCONVP 500 501 119 4 19.38 VP 501 0 0 GCONVN 500 502 119 5 19.38 VN 502 0 0 8/14 TS924 ********* orientation isink isource VINT2 503 0 5 FCOPY 503 504 VOUT 1 DCOPYP 504 505 MDTH 400E-9 VCOPYP 505 0 0 DCOPYN 506 504 MDTH 400E-9 VCOPYN 0 506 0 *************************** F2PP 19 5 poly(2) VCOPYP VP 0 0 0 0 F2PN 19 5 poly(2) VCOPYP VN 0 0 0 0 F2NP 19 5 poly(2) VCOPYN VP 0 0 0 0 F2NN 19 5 poly(2) VCOPYN VN 0 0 0 0 * COMPENSATION ************ CC 19 119 25p * OUTPUT *********** DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 6.250000E+02 VIPM 28 4 5.000000E+01 HONM 21 27 VOUT 6.250000E+02 VINM 5 27 5.000000E+01 VOUT 3 23 0 ROUT 23 19 6 COUT 3 5 1.300000E-10 DOP 19 25 MDTH 400E-12 VOP 4 25 1.052 DON 24 19 MDTH 400E-12 VON 24 5 1.052 .ENDS ;TS92X ******* Macromodel 0.5 0.5 1.75 1.75 9/14 Package information TS924 4 Package information In order to meet environmental requirements, STMicroelectronics offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics trademark. ECOPACK specifications are available at: www.st.com. 4.1 DIP14 package information Figure 13. DIP14 package mechanical drawing Table 6. Ref. DIP14 package mechanical data Millimeters Min. Typ. Max. Min. 0.020 1.65 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 0.130 0.100 0.335 0.100 0.600 0.280 0.201 0.055 0.020 0.010 0.787 0.065 Inches Typ. Max. a1 B b b1 D E e e3 F I L Z 0.51 1.39 10/14 TS924 Package information 4.2 SO-14 package information Figure 14. SO-14 package mechanical drawing Table 7. SO-14 package mechanical data Dimensions Ref. Min. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 8.55 5.8 0.35 0.19 0.1 Millimeters Typ. Max. 1.75 0.2 1.65 0.46 0.25 0.5 45° (typ.) 8.75 6.2 1.27 7.62 4.0 5.3 1.27 0.68 8° (max.) 0.149 0.181 0.019 0.336 0.228 0.013 0.007 0.003 Min. Inches Typ. Max. 0.068 0.007 0.064 0.018 0.010 0.019 0.344 0.244 0.050 0.300 0.157 0.208 0.050 0.026 11/14 Package information TS924 4.3 TSSOP14 package information Figure 15. TSSOP14 package mechanical drawing A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 Figure 16. TSSOP14 package mechanical data Dimensions Ref. Min. A A1 A2 b c D E E1 e K L1 0° 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8° 0.75 0° 0.018 0.024 1 Millimeters Typ. Max. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8° 0.030 0.004 0.039 Min. Inches Typ. Max. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176 12/14 TS924 Ordering information 5 Ordering information Table 8. Order codes Temperature range Package Packaging Marking TS924IN DIP14 TS924AIN TS924ID TS924IDT SO-14 TS924AID TS924AIDT TS924IYD (1) TS924IYDT (1) TS924AIYD (1) TS924AIYDT (1) TS924IPT (2) TS924AIPT (2) Order code TS924IN Tube TS924AIN 924I Tube or Tape and reel 924AI 924IY -40°C, +125°C SO-14 (Automotive grade) Tube or Tape and reel 924AIY 924I TSSOP14 TSSOP14 (Automotive grade) Tape and reel 924AI 924IY Tape and reel 924AIY TS924IYPT (2) TS924AIYPT (2) 1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent. 2. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent are on-going. 6 Revision history Table 9. Date 28-May-2001 12-May-2005 31-Jul-2005 Document revision history Revision 1 2 3 First release. Modifications on AMR Table on page 2 (explanation of Vid and Vin limits, ESD MM and CDM values added, Rthja added). PPAP references inserted in the datasheet see Table 1 on page 3. Package mechanical data modified. TS924IYPT/TS924AYIPT PPAP reference inserted in order code table. Macromodel modified. Added footnotes for automotive grade order codes in order code table. Updated document format. Changes 30-Nov-2005 4 11-Mar-2008 5 13/14 TS924 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 14/14