TS924, TS924A
Rail-to-rail output current quad operational amplifier
Datasheet - production data
• ESD internal protection: 3 kV
• Latch-up immunity
• Macromodel included in this specification
D
SO14
(plastic micropackage)
Related products
• See the TS921 device for the single version
and the TS922 device for the dual version
• See the TSX56x series for smaller packages
Applications
P
TSSOP14
(thin shrink small outline package)
• Headphone amplifiers
• Piezoelectric speaker drivers
• Sound cards
• MPEG boards, multimedia systems
Pin connections (top view)
• Line drivers, buffers
14 Output 4
Output 1 1
Inverting input 1 2
-
-
13 Inverting input 4
Non-inverting input 1 3
+
+
12 Non-inverting input 4
VCC + 4
Non-inverting input 2 5
Inverting input 2 6
• Cordless telephones and portable
communication equipment
• Instrumentation with low noise as key factor
11 VCC +
+
10 Non-inverting input 3
-
-
9
Inverting input 3
8
Output 3
Output 2 7
Features
• Rail-to-rail input and output
• Low noise: 9 nV/√Hz
• Low distortion
• High output current: 80 mA
(able to drive 32 Ω loads)
• High-speed: 4 MHz, 1.3 V/µs
Description
The TS924 and TS924A devices are rail-to-rail
quad BiCMOS operational amplifiers optimized
and fully specified for 3 V and 5 V operation.
High output current allows low load impedances
to be driven.
The TS924 and TS924A devices exhibit a very
low noise, low distortion, low offset, and high
output current capability, making these devices an
excellent choice for high-quality, low-voltage, and
battery-operated audio systems.
The devices are stable for capacitive loads up to
500 pF.
• Operating range from 2.7 V to 12 V
• Low input offset voltage: 900 µV max.
(TS924A)
June 2014
This is information on a product in full production.
DocID5065 Rev 11
1/18
www.st.com
Contents
TS924, TS924A
Contents
1
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 3
2
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Macromodel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4
3.1
Important note concerning this macromodel . . . . . . . . . . . . . . . . . . . . . . 10
3.2
Electrical characteristics from macromodelization . . . . . . . . . . . . . . . . . . 10
3.3
Macromodel code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1
SO14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2
TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2/18
DocID5065 Rev 11
TS924, TS924A
1
Absolute maximum ratings and operating conditions
Absolute maximum ratings and operating conditions
Table 1. Absolute maximum ratings
Symbol
VCC
Vid
Parameter
Supply voltage(1)
Differential input voltage
Tstg
Storage temperature
VCC- -0.3 to VCC+ +0.3
-65 to +150
°C
Maximum junction temperature
150
Thermal resistance junction-to-ambient(4)
SO14
TSSOP14
66
100
°C/W
3
kV
100
V
CDM: charged device model
SO14
TSSOP14
1.5
1
kV
Output short-circuit duration
See footnote(8)
HBM: human body model(5)
MM: machine model(6)
ESD
V
±1
(3)
Input voltage
Rthja
Unit
14
(2)
Vin
Tj
Value
(7)
Latch-up immunity
200
Soldering temperature (10 sec.), leaded version
250
Soldering temperature (10 sec.), unleaded version
260
mA
°C
1. All voltage values, except the differential voltage, are with respect to network ground terminal.
2. The differential voltage is the non-inverting input terminal with respect to the inverting input terminal. If
Vid > ±1 V, the maximum input current must not exceed ±1 mA. In this case (Vid > ±1 V), an input series
resistor must be added to limit input current.
3. Do not exceed 14 V.
4. Short-circuits can cause excessive heating and destructive dissipation. Rth are typical values.
5. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a
1.5 kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
6. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between
two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of
connected pin combinations while the other pins are floating.
7. Charged device model: all pins and the package are charged together to the specified voltage and then
discharged directly to ground through only one pin. This is done for all pins.
8. There is no short-circuit protection inside the device: short-circuits from the output to VCC can cause
excessive heating. The maximum output current is approximately 80 mA, independent of the magnitude of
VCC. Destructive dissipation can result from simultaneous short-circuits on all amplifiers.
Table 2. Operating conditions
Symbol
Parameter
VCC
Supply voltage
Vicm
Common mode input voltage range
Toper
Operating free air temperature range
Value
2.7 to 12
DocID5065 Rev 11
VCC- -0.2 to VCC+ +0.2
-40 to +125
Unit
V
°C
3/18
18
Electrical characteristics
2
TS924, TS924A
Electrical characteristics
Table 3. Electrical characteristics at VCC+ = +3 V with VCC- = 0 V, Vicm = VCC+/2, Tamb = 25 °C, and
RL connected to VCC+/2 (unless otherwise specified)
Symbol
Parameter
Min.
Typ.
Max.
Unit
DC performance
Vio
Input offset voltage
TS924
TS924A
Tmin ≤ Tamb ≤ Tmax
TS924
TS924A
3
0.9
5
1.8
Input offset voltage drift
2
Iio
Input offset current - Tmin ≤ Tamb ≤ Tmax
1
30
Iib
Input bias current - Tmin ≤ Tamb ≤ Tmax
15
100
DVio
CMR
Vicm from 0 to 3 V
Tmin ≤ Tamb ≤ Tmax
60
56
80
SVR
Supply voltage rejection ratio - VCC+ = 2.7 to 3.3 V
Tmin ≤ Tamb ≤ Tmax
60
60
85
Avd
Large signal voltage gain (Vout = 2 Vpk-pk)
RL= 10 kΩ, Tmin ≤ Tamb ≤ Tmax
RL = 600 Ω, Tmin ≤ Tamb ≤ Tmax
RL = 32 Ω
70
15
200
35
16
VOH
High level output voltage
RL= 10 kΩ, Tmin ≤ Tamb ≤ Tmax
RL = 600 Ω, Tmin ≤ Tamb ≤ Tmax
RL = 32 Ω
VOL
Io
ICC
mV
µV/°C
nA
dB
V/mV
2.90
2.87
V
2.63
Low level output voltage
RL= 10 kΩ, Tmin ≤ Tamb ≤ Tmax
RL = 600 Ω, Tmin ≤ Tamb ≤ Tmax
RL = 32 Ω
50
100
mV
1.5
1.6
mA
180
Output short-circuit current
50
Supply current /operator - no load, Vout = VCC+/2
Tmin ≤ Tamb ≤ Tmax
80
1
AC performance
Gain bandwidth product - RL = 600 Ω
4
MHz
φm
Phase margin at unit gain - RL = 600 Ω, CL =100 pF
68
Degrees
Gm
Gain margin - RL = 600 Ω, CL =100 pF
12
dB
SR
Slew rate
1.3
V/µs
en
Equivalent input noise voltage - f = 1 kHz
9
nV
-----------Hz
GBP
4/18
0.7
DocID5065 Rev 11
TS924, TS924A
Electrical characteristics
Table 3. Electrical characteristics at VCC+ = +3 V with VCC- = 0 V, Vicm = VCC+/2, Tamb = 25 °C, and
RL connected to VCC+/2 (unless otherwise specified) (continued)
Symbol
THD
Cs
Parameter
Total harmonic distortion
Vout = 2 Vpk-pk, F = 1 kHz, Av = 1, RL = 600 Ω
Channel separation
DocID5065 Rev 11
Min.
Typ.
Max.
Unit
0.005
%
120
dB
5/18
18
Electrical characteristics
TS924, TS924A
Table 4. VCC+ = +5 V, VCC- = 0 V, Vicm = VCC/2, Tamb = 25 °C, RL connected to VCC/2
(unless otherwise specified)
Symbol
Parameter
Min.
Typ.
Max.
Unit
DC performance
Vio
Input offset voltage
TS924
TS924A
Tmin ≤ Tamb ≤ Tmax
TS924
TS924A
3
0.9
5
1.8
Input offset voltage drift
2
Iio
Input offset current - Tmin ≤ Tamb ≤ Tmax
1
30
Iib
Input bias current - Tmin ≤ Tamb ≤ Tmax
15
100
DVio
CMR
Vicm from 0 to 5 V
Tmin ≤ Tamb ≤ Tmax
60
56
80
SVR
Supply voltage rejection ratio - VCC+ = 3 V to 5 V
Tmin ≤ Tamb ≤ Tmax
60
60
85
Avd
Large signal voltage gain (Vout = 2Vpk-pk)
RL= 10 kΩ, Tmin ≤ Tamb ≤ Tmax
RL = 600 Ω, Tmin ≤ Tamb ≤ Tmax
RL = 32 Ω
70
20
200
40
17
VOH
High level output voltage
RL= 10 kΩ, Tmin ≤ Tamb ≤ Tmax
RL = 600 Ω, Tmin ≤ Tamb ≤ Tmax
RL = 32 Ω
VOL
Io
ICC
mV
µV/°C
nA
dB
V/mV
4.90
4.85
V
4.4
Low level output voltage
RL= 10 kΩ, Tmin ≤ Tamb ≤ Tmax
RL = 600 Ω, Tmin ≤ Tamb ≤ Tmax
RL = 32 Ω
50
120
mV
1.5
1.6
mA
300
Output short-circuit current
50
Supply current / operator - no load, Vout = VCC+/2
Tmin ≤ Tamb ≤ Tmax
80
1
AC performance
Gain bandwidth product - RL = 600 Ω
4
MHz
φm
Phase margin at unit gain - RL = 600 Ω, CL =100 pF
68
Degrees
Gm
Gain margin -RL = 600 Ω, CL =100 pF
12
dB
SR
Slew rate
1.3
V/µs
en
Equivalent input noise voltage - f = 1 kHz
9
nV
-----------Hz
0.005
%
120
dB
GBP
THD
Cs
6/18
0.7
Total harmonic distortion
Vout = 2 Vpk-pk, F = 1 kHz, Av = 1, RL = 600 Ω
Channel separation
DocID5065 Rev 11
TS924, TS924A
Electrical characteristics
Figure 1. Output short-circuit current
vs. output voltage (VCC = 0/12 V)
Figure 2. Output short-circuit current
vs. output voltage (VCC = 0/3 V)
Figure 3. Voltage gain and phase vs. frequency
(CL = 500 pF, VCC = ±1.5 V)
Figure 4. Output short-circuit current
vs. output voltage (VCC = 0/5 V)
Phase
d
CL = 500 pF
VCC = ±1.5 V
Gain
Figure 5. Voltage gain and phase vs. frequency Figure 6. THD + noise vs. frequency (RL = 2 kΩ,
(RL = 10 kΩ, CL = 100 pF, VCC = ±1.5 V)
VO = 10 Vpp, VCC = ±6 V, Av = -1)
RL =10 kΩ
CL = 100 pF
VCC = ±1.5 V
RL = 2 kΩ, VO = 10 Vpp
VCC = ±6 V, Av = -1
Phase
Gain
DocID5065 Rev 11
7/18
18
Electrical characteristics
TS924, TS924A
Figure 7. THD + noise vs. frequency (RL = 2 kΩ, Figure 8. THD + noise vs. frequency (RL = 32 Ω,
VO = 10 Vpp, VCC = ±6 V, Av = 1)
VO = 2 Vpp, VCC = ±1.5 V, Av = 10)
RL = 32 Ω, VO = 2 Vpp
VCC = ±1.5 V, Av = 10
RL = 2 kΩ, VO = 10 Vpp
VCC = ±6 V, Av = 1
Figure 9. THD + noise vs. Vout (RL = 32 Ω,
f = 1 kHz, VCC = ±1.5 V, Av = -1)
Figure 10. THD + noise vs. frequency (RL = 32 Ω,
VO = 4 Vpp, VCC = ±2.5 V, Av = 1)
RL = 32 Ω, VO = 4 Vpp
VCC = ±2.5 V, Av = 1
RL = 32 Ω, f = 1 kHz
VCC = ±1.5 V, Av = -1
Figure 11. THD + noise vs. Vout (RL = 600 Ω,
f = 1 kHz, VCC = ±1.5 V , Av = -1)
Figure 12. THD + noise vs. Vout (RL = 2 kΩ,
f = 1 kHz, VCC = ±1.5 V, Av = -1)
RL = 2 kΩ, f = 1 kHz
VCC = ±1.5 V, Av = -1
8/18
DocID5065 Rev 11
TS924, TS924A
Electrical characteristics
Figure 13. PSRR for TS924/TS924A at VCC = 5 V, Vicm = 2.5 V, T = 25 °C, RI = 100 kΩ,
and CI = 100pF
ϭϮϬ
ϭϬϬ
ϴϬ
W^ZZ;ĚͿ
ϲϬ
sZ'WŽƐ
sZ'EĞŐ
ϰϬ
ϮϬ
Ϭ
ͲϮϬ
ϭϬ
ϭϬϬ
ϭϬϬϬ
ϭϬϬϬϬ
ϭϬϬϬϬϬ
ϭϬϬϬϬϬϬ
ϭϬϬϬϬϬϬϬ
&ƌĞƋƵĞŶĐLJ;ŚnjͿ
DocID5065 Rev 11
9/18
18
Macromodel
TS924, TS924A
3
Macromodel
3.1
Important note concerning this macromodel
Note the following remarks before using this macromodel:
•
All models are a trade-off between accuracy and complexity (that is, simulation time).
•
Macromodels are not a substitute to breadboarding; rather, they confirm the validity of
a design approach and help to select surrounding component values.
•
A macromodel emulates the nominal performance of a typical device within specified
operating conditions (for example, temperature, supply voltage). Thus, the
macromodel is often not as exhaustive as the datasheet, its purpose is to illustrate the
main parameters of the product.
Data derived from macromodels used outside of the specified conditions (such as VCC and
temperature) or worse, outside of the device operating conditions (such as VCC and Vicm),
are not reliable in any way.
Section 3.2 presents the electrical characteristics resulting from the use of these
macromodels.
3.2
Electrical characteristics from macromodelization
Table 5. Macromodel simulation at VCC+ = 3 V, VCC- = 0 V, RL, CL connected to VCC/2,
and Tamb = 25 °C (unless otherwise specified)
Symbol
Conditions
Vio
Unit
0
mV
Avd
RL = 10 kΩ
200
V/mV
ICC
No load, per operator
1.2
mA
-0.2 to 3.2
Vicm
10/18
Value
V
VOH
RL = 10 kΩ
2.95
VOL
RL = 10 kΩ
25
Isink
VO = 3 V
80
Isource
VO = 0 V
80
GBP
RL = 600 kΩ
4
MHz
SR
RL = 10 kΩ, CL = 100 pF
1
V/µs
φm
RL = 600 kΩ
68
Degrees
DocID5065 Rev 11
mV
mA
TS924, TS924A
3.3
Macromodel
Macromodel code
** Standard Linear Ics Macromodels, 1996.
** CONNECTIONS:
* 1 INVERTING INPUT
* 2 NON-INVERTING INPUT
* 3 OUTPUT
* 4 POSITIVE POWER SUPPLY
* 5 NEGATIVE POWER SUPPLY
.SUBCKT TS92X 1 2 3 4 5
*
.MODEL MDTH D IS=1E-8 KF=2.664234E-16 CJO=10F
*
* INPUT STAGE
CIP 2 5 1.000000E-12
CIN 1 5 1.000000E-12
EIP 10 5 2 5 1
EIN 16 5 1 5 1
RIP 10 11 8.125000E+00
RIN 15 16 8.125000E+00
RIS 11 15 2.238465E+02
DIP 11 12 MDTH 400E-12
DIN 15 14 MDTH 400E-12
VOFP 12 13 DC 153.5u
VOFN 13 14 DC 0
IPOL 13 5 3.200000E-05
CPS 11 15 1e-9
DINN 17 13 MDTH 400E-12
VIN 17 5 -0.100000e+00
DINR 15 18 MDTH 400E-12
VIP 4 18 0.400000E+00
FCP 4 5 VOFP 1.865000E+02
FCN 5 4 VOFN 1.865000E+02
FIBP 2 5 VOFP 6.250000E-03
FIBN 5 1 VOFN 6.250000E-03
* GM1 STAGE ***************
FGM1P 119 5 VOFP 1.1
FGM1N 119 5 VOFN 1.1
RAP 119 4 2.6E+06
RAN 119 5 2.6E+06
* GM2 STAGE ***************
G2P 19 5 119 5 1.92E-02
G2N 19 5 119 4 1.92E-02
R2P 19 4 1E+07
DocID5065 Rev 11
11/18
18
Macromodel
TS924, TS924A
R2N 19 5 1E+07
**************************
VINT1 500 0 5
GCONVP 500 501 119 4 19.38
VP 501 0 0
GCONVN 500 502 119 5 19.38
VN 502 0 0
********* orientation isink isource *******
VINT2 503 0 5
FCOPY 503 504 VOUT 1
DCOPYP 504 505 MDTH 400E-9
VCOPYP 505 0 0
DCOPYN 506 504 MDTH 400E-9
VCOPYN 0 506 0
***************************
F2PP 19 5 poly(2) VCOPYP VP 0 0 0 0 0.5
F2PN 19 5 poly(2) VCOPYP VN 0 0 0 0 0.5
F2NP 19 5 poly(2) VCOPYN VP 0 0 0 0 1.75
F2NN 19 5 poly(2) VCOPYN VN 0 0 0 0 1.75
* COMPENSATION ************
CC 19 119 25p
* OUTPUT ***********
DOPM 19 22 MDTH 400E-12
DONM 21 19 MDTH 400E-12
HOPM 22 28 VOUT 6.250000E+02
VIPM 28 4 5.000000E+01
HONM 21 27 VOUT 6.250000E+02
VINM 5 27 5.000000E+01
VOUT 3 23 0
ROUT 23 19 6
COUT 3 5 1.300000E-10
DOP 19 25 MDTH 400E-12
VOP 4 25 1.052
DON 24 19 MDTH 400E-12
VON 24 5 1.052
.ENDS ;TS92X
12/18
DocID5065 Rev 11
TS924, TS924A
4
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
DocID5065 Rev 11
13/18
18
Package information
4.1
TS924, TS924A
SO14 package information
Figure 14. SO14 package outline
Table 6. SO14 package mechanical data
Dimensions
Symbol
Millimeters
Min.
Typ.
Inches
Max.
Min.
Max.
A
1.35
1.75
0.05
0.068
A1
0.10
0.25
0.004
0.009
A2
1.10
1.65
0.04
0.06
B
0.33
0.51
0.01
0.02
C
0.19
0.25
0.007
0.009
D
8.55
8.75
0.33
0.34
E
3.80
4.0
0.15
0.15
e
1.27
0.05
H
5.80
6.20
0.22
0.24
h
0.25
0.50
0.009
0.02
L
0.40
1.27
0.015
0.05
k
ddd
14/18
Typ.
8° (max.)
0.10
DocID5065 Rev 11
0.004
TS924, TS924A
4.2
Package information
TSSOP14 package information
Figure 15. TSSOP14 package outline
Table 7. TSSOP14 package mechanical data
Dimensions
Symbol
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.20
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.90
5.00
5.10
0.193
0.197
0.201
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.176
e
L
0.65
0.45
L1
k
aaa
1.00
0.60
0.0256
0.75
0.018
1.00
0°
0.024
0.030
0.039
8°
0.10
DocID5065 Rev 11
0°
8°
0.004
15/18
18
Ordering information
5
TS924, TS924A
Ordering information
Table 8. Order codes
Order code
Temperature range
TS924ID
TS924IDT
TS924AID
TS924AIDT
TS924IYDT(1)
TS924AIYDT
(1)
TS924IPT
-40 °C, 125 °C
Package
Packaging
SO14
Tube or
tape and reel
TS924AIPT
(1)
TS924IYPT
TS924AIYPT(1)
TSSOP14
(automotive grade)
924I
924AI
924IY
SO14
(automotive grade)
TSSOP14
Marking
924AIY
924I
Tape and reel
924AI
924IY
924AIY
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening
according to AEC Q001 and Q 002 or equivalent.
16/18
DocID5065 Rev 11
TS924, TS924A
6
Revision history
Revision history
Table 9. Document revision history
Date
Revision
28-May-2001
1
First release.
12-May-2005
2
Modifications on AMR Table on page 3 (explanation of Vid and Vin limits, ESD MM
and CDM values added, Rthja added).
31-Jul-2005
3
PPAP references inserted in the datasheet, see order codes table.
30-Nov-2005
4
Package mechanical data modified.
TS924IYPT/TS924AYIPT PPAP reference inserted in order code table.
Macromodel modified.
11-Mar-2008
5
Added footnotes for automotive grade order codes in
Table 8: Order codes.
Updated document format.
6
ESD tolerance improved for machine model in
Table 1: Absolute maximum ratings.
Removed TS914AIN order code and corrected footnotes in
Table 8: Order codes.
08-Oct-2009
7
Added part number TS924A on cover page.
Added limits on full temperature range in Table 3 and Table 4.
Removed order codes TS924IYD and TS924AIYD from Table 8.
15-Apr-2011
8
Modified CMR parameter values in Table 3 and Table 4.
19-May-2011
9
Added A version in title and header.
04-Dec-2012
10
Added DIP14 package to Figure on page 1.
Added Related products to Features.
Added DIP14 with value for Rthja in Table 1.
Added conditions to titles of Figure 1 to Figure 12.
Replaced VCC by VCC+ and VDD by VCC- in title of Table 5.
Qualified status of TS924IYPT and TS924AIYPT order codes in Table 8.
Minor corrections throughout document.
05-Jun-2014
11
Removed DIP14 package and order code pertaining to it
Added Figure 13
19-Dec-2008
Changes
DocID5065 Rev 11
17/18
18
TS924, TS924A
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
18/18
DocID5065 Rev 11