TSH22IDT

TSH22 HIGH PERFORMANCE DUAL BIPOLAR OPERATINAL AMPLIFIER ■ HIGH GAIN BANDWIDTH PRODUCT : 25MHz ■ HIGH SLEW RATE : 15V/µs ■ SINGLE OR DUAL SUPPLY OPERATION : 3V TO 30V (±1.5V to ±15V) ■ LOW VOLTAGE NOISE : 14nV/√Hz N DIP8 (Plastic Package) ■ NO PHASE INVERSION ■ ESD TOLERANCE : 2kV ■ LATCH-UP IMMUNITY ■ SPICE MACROMODEL INCLUDED IN THIS SPECIFICATION D SO8 (Plastic Micropackage) DESCRIPTION TheTSH22 is a dual bipolar operational amplifier offering a single supply operation from 3V to 30V with very good performances : medium speed (25MHz), unity gain stability and low noise. ORDER CODE The TSH22 is therefore an enhanced replacement of standard dual operational amplifiers. TSH22I Package Part Number Temperature Range -40°C, +125°C N D • • N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) PIN CONNECTIONS (top view) Output 1 1 Inverting input 1 2 - Non-inverting input 1 3 + V November 2001 CC - 4 8 VCC + 7 Output 2 - 6 Inverting input 2 + 5 Non-inverting input 2 1/11 TSH22 SCHEMATIC DIAGRAM (1/2 TSH22) ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply Voltage 1) Vid Differential Input Voltage Vi Input Voltage (see note 1) Output Short-circuit Duration Toper Tj 2) Operating Free-Air Temperature Range Maximum Junction Temperature Tstg Storage Temperature Range ptot Maximum Power Dissipation (see note 2) Value Unit ±18 to 36 V ±36 V ±18 V Infinite -40 to +125 °C +150 °C -65 to +150 °C 500 mW Value Unit 3 to 30 V Either or both input voltages must not exceed the magnitude of VCC+ or VCCPower dissipation must be considered to ensure maximum junction temperature (T j) is not exceeded 1. 2. OPERATING CONDITIONS Symbol VCC 2/11 Parameter Supply Voltage TSH22 ELECTRICAL CHARACTERISTICS VCC+ = 15V, V cc- = -15V, Tamb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Input Offset Voltage (Vic = 0V, Vo = 0V) Vio ∆Vio Unit mV Vcc+ = +15V, Vcc- = -15V Tmin ≤ Tamb ≤ Tmax 2.5 3.5 2.5 Vcc+ = +5V, Vcc- = 0V Input Offset Voltage Drift (Vic = 0V, Vo = 0V) µV/°C 2 Iio Input Offset Current (Vic = 0V, Vo = 0V) 3 65 nA Iib Input Bias Current (Vic = 0V, Vo = 0V) 100 650 nA Vicm Common Mode Input Voltage Range Vcc- to Vcc+-1.8V V 32 20 100 V/mV 13.4 13.9 -13.9 14 -14.7 Avd ±Vopp Large Signal Voltage Gain (RL = 2kΩ, Vo = 0V to +10V Tmin ≤ Tamb ≤ Tmax Output Voltage Swing (Vid = ±1V) Vcc+ = +15V, Vcc- = -15V RL = 2kΩ VOH VOL RL =10kΩ VOH VOL Vcc+=+5V, Vcc-=0V Io CMR SVR Icc SR GBP B ∅m en Vo1/Vo2 THD RL = 2kΩ VOH VOL Output Short Circuit Current (Vid = ±1V, Vo = 0V) V 13.4 -13.5 -14.1 3.7 0.15 0.2 mA Source Sink Common Mode Rejection Ratio (Vic = -15V to +13.2V) Supply Voltage Rejection Ratio Vcc+/Vcc- = +15V/-15V to +5V/-5V Supply Current (Vo = 0V, no load, each amplifier) 25 25 37 37 80 100 90 105 dB dB mA Vcc+ = +15V, Vcc- = -15V Tmin ≤ Tamb ≤ Tmax 2.15 2.75 3 2.75 Vcc+=+5V, Vcc-=0V Slew Rate (Vi = -10V to +10V, CL = 100pF, RL = 2kΩ, AV = +1) 8 15 Gain Bandwith Product (f = 100kHz, RL = 2kΩ, CL = 100pF) 17 25 MHz 5 MHz 50 40 Degrees Unity Gain Bandwith (Open loop) Phase Margin RL = 2kΩ RL = 2kΩ, CL = 100pF V/µs Equivalent Input Noise Voltage (Rs = 100Ω, f = 1kHz) 14 nV -----------Hz Channel Separation (f = 20Hz to 20kHz) 120 dB Total Harmonic Distortion (Vcc = ±15V, f = 1kHz, AVCL = 20dB, RL = 600Ω, Vo = 3Vrms) 0.003 % 3/11 TSH22 MACROMODEL ** Standard Linear Ics Macromodels, 1993. CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT TSH22 1 3 2 4 5 (analog) ******************************************************** * .MODEL MDTH D IS=1E-8 KF=7.976636E-15 CJO=10F * INPUT STAGE CIP 2 5 1.200000E-11 CIN 1 5 1.200000E-11 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 1.083333E+00 RIN 15 16 1.083333E+00 RIS 11 15 8.942641E+00 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0 VOFN 13 14 DC 0 IPOL 13 5 2.400000E-04 CPS 11 15 10.5E-09 DINN 17 13 MDTH 400E-12 VIN 17 5 -0.200000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 1.800000E+00 FCP 4 5 VOFP 7.750000E+00 FCN 5 4 VOFN 7.750000E+00 FIBP 2 5 VOFN 5.000000E-04 FIBN 5 1 VOFP 5.000000E-04 * AMPLIFYING STAGE FIP 5 19 VOFP 6.708333E+02 FIN 5 19 VOFN 6.708333E+02 GVNEG 5 19 5 13 1.395908E-05 GVPOS 5 19 4 13 1.395908E-05 RG1 19 5 8.056996E+04 RG2 19 4 8.056996E+04 CC 19 29 1.100000E-08 HZTP 30 29 VOFP 6.545046E+01 HZTN 5 30 VOFN 6.545046E+01 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 4.054054E+03 VIPM 28 4 1.500000E+02 HONM 21 27 VOUT 4.054054E+03 VINM 5 27 1.500000E+02 RPM1 5 80 1E+06 RPM2 4 80 1E+06 GAVPH 5 82 19 80 6.00E-07 RAVPHGH 82 4 3333222 RAVPHGB 82 5 3333222 RAVPHDH 82 83 1000000 RAVPHDB 82 84 1000000 CAVPHH 4 83 0.12243E-12 CAVPHB 5 84 0.12243E-12 EOUT 26 23 82 5 1 VOUT 23 5 0 ROUT 26 3 2.472597E+01 COUT 3 5 1.000000E-12 DOP 19 25 MDTH 400E-12 VOP 4 25 1.824860E+00 DON 24 19 MDTH 400E-12 VON 24 5 1.824860E+00 .ENDS ELECTRICAL CHARACTERISTICS Vcc = ±15V, Tamb = 25°C (unless otherwise specified) Symbol Conditions Vid Avd RL = 2kΩ Icc No load, per operator Value Unit 0 mV 100 dB 2 mA -15.2 to 13.8 V RL = 2kΩ +13.9 V VOL RL = 2kΩ -13.9 V Isink Vo = 0V 40 mA Isource Vo = 0V 40 mA GBP RL = 2kΩ, CL = 100pF 34 MHz Vicm VOH SR RL = 2kΩ, CL = 100pF 10 V/µs ∅m RL = 2kΩ, CL = 100pF 36 Degrees ∅m RL = 2kΩ, CL = 300pF 26 Degrees 4/11 TSH22 APPLICATIONS INFORMATION TSH22 IN COMPARATOR APPLICATION The TSH22 is a dual high performances operational amplifier featuring speed of 30MHz and single supply operation from 3V to 30V. Most of operational amplifiers are not suited for comparator use because of low transition speed, output signal incompatible with standard logics level and mainly, phase inversion. The phase inversion occures when a strong differential signal is applied to the device inputs. The output level is then inverted and shows a wrong logic state. TSH22 does not present this problematic behaviour. Displayed curves below show the device response in standard comparator configuration without external components. Transition speed : Typical transition speed under a single 5V supply voltage is about 2µs from 50mV overdrive. VOH min. is 3.7V and V OL max. is 0.2V (2kΩ load) making it compatible with standard logic families. Figures 3 & 4 show output signal transition for a 50mV and 250mV input signal overdrive respectively of 3µs and 1µs. Figure 1 : Basic comparator application Figure 2 : Operating conditions +5V Vin+ TSH22 Vout Vref 2kW Figure 3 : Transition speed@ 50mV overdrive Figure 4 : Transition speed@ 250mV overdrive 5/11 TSH22 PHASE INVERSION Figure 5 & 6 show the behaviour in follower stage with saturation output of TSH22 versus 15MHz standard operational amplifier. Figure 5 : Behaviour with TSH22 Figure 6 : Saturation behaviour with 15MHz standard operational amplifier Input & Ouput Voltages, Vid (V), Vo (V) At high differential input voltage, the TSH22 keeps the right output level thanks to its specific input structures. The advantage is obvious on the following figures and can be also an advantage in linear use when saturation might occure. 6/11 8 Vid 6 4 2 0 -2 -4 Vo -6 -8 Time (50µs/div) TSH22 INPUT OFFSET VOLTAGE DRIFT VERSUS TEMPERATURE SUPPLY CURRENT VERSUS SUPPLY VOLTAGE (BOTH OP-AMPS) 0.4 Input Offset Voltage, Vio (mV) 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -50 -25 0 25 50 75 100 125 Temperature, Tamb (˚C) SINK CURRENT SOURCE CURRENT Output Sink Current, Isink (mA) 50 45 40 35 30 25 20 15 Tamb = 25˚C Vcc = ±15V Vid = 1V 10 5 0 -15 -12 -9 -6 -3 0 3 6 Applied Output Voltage, Vo (V) 9 12 SLEW RATE @ 30V 15 SLEW RATE @ 3V 20 0.8 Output Voltage, Vo (V) 10 5 0 -5 -10 -15 Tamb = 25˚C Vcc = +2V/-1V Av = +1 RL = 2kΩ CL = 100pF 0.6 Output Voltage, Vo (V) Tamb = 25˚C Vcc = ±15V Av = +1 RL = 2kΩ CL = 100pF 15 0.4 0.2 0 -0.2 -0.4 -0.6 -20 Time (0.5µs/div) -0.8 Time (0.2µs/div) 7/11 TSH22 LARGE SIGNAL VOLTAGE GAIN @NO LOAD LARGE SIGNAL VOLTAGE GAIN @ LOAD 20 Output Voltage, Vo (V) 15 10 5 0 -5 Tamb = 25˚C Vcc = ±15V No Load -10 -15 -20 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 Differential Input Voltage, Vid (mV) SMALL SIGNAL RESPONSE @ 30V SMALL SIGNAL RESPONSE @ 3V UNITY GAIN BANDWITH @ 30V UNITY GAIN BANDWITH @ 3V 45 Tamb = 25˚C Vcc = +2V/-1V AVCL = 100 RL = 2kΩ CL = 100pF 35 Voltage Gain (dB) 30 0 30 25 Gain 20 60 15 90 120 10 Phase 5 150 0 180 -5 10k 100k 1M Frequency, F (Hz) 8/11 10M Phase (degrees) 40 TSH22 CLOSED LOOP BANDWITH @ 30V CLOSED LOOP BANDWITH @ 3V 21 21 18 15 AVCL = +5 15 9 AVCL = +2 6 3 9 AVCL = +2 6 3 AVCL = +1 0 -3 -3 -6 -6 -9 Tamb = 25˚C Vcc = +2V/-1V AVCL = 5,2,1 RL = 2kΩ CL = 100pF AVCL = +5 12 Voltage Gain (dB) Voltage Gain (dB) 12 0 18 Tamb = 25˚C Vcc = ±15V AVCL = 5,2,1 RL = 2kΩ CL = 100pF AVCL = +1 -9 100k 1M Frequency, F (Hz) 10M 100k 1M Frequency, F (Hz) 10M 9/11 TSH22 PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Millimeters Inches Dim. Min. A a1 B b b1 D E e e3 e4 F i L Z 10/11 Typ. Max. Min. 3.32 0.51 1.15 0.356 0.204 1.65 0.55 0.304 10.92 9.75 7.95 0.020 0.045 0.014 0.008 Max. 0.065 0.022 0.012 0.430 0.384 0.313 2.54 7.62 7.62 3.18 Typ. 0.131 0.100 0.300 0.300 6.6 5.08 3.81 1.52 0.125 0260 0.200 0.150 0.060 TSH22 PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) s b1 b a1 A a2 C c1 a3 L E e3 D M 5 1 4 F 8 Millimeters Inches Dim. Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S Typ. Max. 0.65 0.35 0.19 0.25 1.75 0.25 1.65 0.85 0.48 0.25 0.5 4.8 5.8 5.0 6.2 0.1 Min. Typ. Max. 0.026 0.014 0.007 0.010 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.189 0.228 0.197 0.244 0.004 45° (typ.) 1.27 3.81 3.8 0.4 0.050 0.150 4.0 1.27 0.6 0.150 0.016 0.157 0.050 0.024 8° (max.) Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States © http://www.st.com 11/11