TSH80, TSH81, TSH82, TSH84
Wide-band rail-to-rail operational amplifiers with standby function
Datasheet - production data
Applications
• Video buffers
• A/D converter drivers
SO8
SOT23-5
• Hi-fi applications
Description
TSSOP8
TSSOP14
Features
• Operating range from 4.5 to 12 V
• 3 dB-bandwidth: 100 MHz
• Slew rate 100 V/µs
• Output current up to 55 mA
• Input single supply voltage
• Output rail-to-rail
• Specified for 150 Ω loads
• Low distortion, THD 0.1%
• SOT23-5, SO8, and TSSOP packages
The TSH8x series offers single, dual and quad
operational amplifiers featuring high video
performance with large bandwidth, low distortion
and excellent supply voltage rejection. These
amplifiers also feature large output voltage
swings and a high output current capability to
drive standard 150 Ω loads.
Running at single or dual supply voltages ranging
from 4.5 to 12 V, these amplifiers are tested at 5 V
(±2.5 V) and 10 V (±5 V) supplies.
The TSH81 device also features a standby mode,
which provides the operational amplifier with
a low power consumption and high output
impedance. This function allows power saving or
signal switching/multiplexing for high-speed and
video applications.
For board space and weight saving, the TSH8x
series is proposed in SOT23-5, SO8, TSSOP8,
and TSSOP14 plastic micropackages.
• Automotive qualification
July 2014
This is information on a product in full production.
DocID009413 Rev 9
1/30
www.st.com
1
Contents
TSH80, TSH81, TSH82, TSH84
Contents
1
Package pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 6
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
Test conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1
Layout precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.2
Video capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5
Precautions on asymmetrical supply operation . . . . . . . . . . . . . . . . . 22
6
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1
SOT23-5 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2
SO8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.3
TSSOP8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.4
TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2/30
DocID009413 Rev 9
TSH80, TSH81, TSH82, TSH84
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical characteristics at VCC+ = +5 V, VCC- = GND, Vic = 2.5 V, Tamb = 25 °C
(unless otherwise specified) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical characteristics at VCC+ = +5 V, VCC- = -5 V, Vic = GND, Tamb = 25 °C
(unless otherwise specified) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Standby mode - VCC+, VCC-, Tamb = 25 °C (unless otherwise specified). . . . . . . . . . . . . . 12
TSH81 standby control pin status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Video results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SOT23-5 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SO8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TSSOP8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TSSOP14 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DocID009413 Rev 9
3/30
List of figures
TSH80, TSH81, TSH82, TSH84
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 16.
Figure 14.
Figure 15.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 31.
Figure 29.
Figure 30.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
Figure 37.
Figure 38.
Figure 39.
4/30
Pin connections for each package (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Closed loop gain and phase vs. frequency (gain = +2, VCC = ±2.5 V) . . . . . . . . . . . . . . . . 13
Overshoot vs. output capacitance (VCC = ±2.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Closed loop gain and phase vs. frequency (gain = -10, VCC = ±2.5 V) . . . . . . . . . . . . . . . 13
Closed loop gain and phase vs. frequency (gain = +11, VCC = ±2.5 V) . . . . . . . . . . . . . . . 13
Large signal measurement – positive slew rate (VCC = ±2.5 V) . . . . . . . . . . . . . . . . . . . . . 13
Large signal measurement – negative slew rate (VCC = ±2.5 V) . . . . . . . . . . . . . . . . . . . . 13
Small signal measurement – rise time (VCC = ±2.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Small signal measurement – fall time (VCC = ±2.5 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Channel separation (crosstalk) vs. frequency schematic (VCC = ±2.5 V) . . . . . . . . . . . . . . 14
Channel separation (crosstalk) vs. frequency (VCC = ±2.5 V) . . . . . . . . . . . . . . . . . . . . . . 14
Equivalent input noise voltage (VCC = ±2.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Maximum output swing (VCC = ±2.5 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Group delay (VCC = ±2.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Standby mode - Ton, Toff (VCC = ±2.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Third order intermodulation (VCC = ±2.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Closed loop gain and phase vs. frequency (gain = +2, VCC = ±5 V) . . . . . . . . . . . . . . . . . 16
Overshoot vs. output capacitance (VCC = ±5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Closed loop gain and phase vs. frequency (gain = -10, VCC = ±5 V) . . . . . . . . . . . . . . . . . 16
Closed loop gain and phase vs. frequency (gain = +11, VCC = ±5 V) . . . . . . . . . . . . . . . . 16
Large signal measurement - positive slew rate (VCC = ±5 V) . . . . . . . . . . . . . . . . . . . . . . . 16
Large signal measurement - negative slew rate (VCC = ±5 V) . . . . . . . . . . . . . . . . . . . . . . 16
Small signal measurement - rise time (VCC = ±5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Small signal measurement - fall time (VCC = ±5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Channel separation (crosstalk) vs. frequency schematic (VCC = ±5 V) . . . . . . . . . . . . . . . 17
Channel separation (crosstalk) vs. frequency (VCC = ±5 V) . . . . . . . . . . . . . . . . . . . . . . . . 17
Equivalent input noise voltage (VCC = ±5 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Maximum output swing (VCC = ±5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Group delay (VCC = ±5 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Standby mode - Ton, Toff (VCC = ±5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Third order intermodulation (VCC = ±5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CCIR330 video line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Measurement on Rohde and Schwarz VSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Asymmetrical supply schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Use of the TSH8x in a gain = -1 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SOT23-5 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SO8 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TSSOP8 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TSSOP14 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DocID009413 Rev 9
TSH80, TSH81, TSH82, TSH84
1
Package pin connections
Package pin connections
Figure 1. Pin connections for each package (top view)
Pin connections TSH80/SOT23-5
Pin connections TSH80/SO8
Pin connections TSH81 SO8/TSSOP8
Pin connections TSH82 SO8/TSSOP8
Pin connections TSH84 TSSOP14
DocID009413 Rev 9
5/30
Absolute maximum ratings and operating conditions
2
TSH80, TSH81, TSH82, TSH84
Absolute maximum ratings and operating conditions
Table 1. Absolute maximum ratings
Symbol
VCC
Vid
Vi
Parameter
Value
Supply voltage(1)
14
(2)
Differential input voltage
±2
(3)
Input voltage
V
±6
Toper
Operating free air temperature range
-40 to +85
Tstg
Storage temperature
-65 to +150
Tj
Unit
Maximum junction temperature
°C
150
junction-to-case(4)
Rthjc
Thermal resistance
SOT23-5
SO8
TSSOP8
TSSOP14
Rthja
Thermal resistance junction-to-ambient area
SOT23-5
SO8
TSSOP8
TSSOP14
250
157
130
110
ESD
HBM: human body model(5)
MM: machine model(6)
CDM: charged device model(7)
2
0.2
1.5
80
28
37
32
°C/W
kV
1. All voltage values, except differential voltage are with respect to the network ground terminal.
2. The differential voltage is the non inverting input terminal with respect to the inverting terminal.
3. The magnitude of input and output must never exceed VCC +0.3 V.
4. Short-circuits can cause excessive heating.
5. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through
a 1.5 kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
6. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between
two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of
connected pin combinations while the other pins are floating.
7. Charged device model: all pins and package are charged together to the specified voltage and then
discharged directly to ground through only one pin. This is done for all pins.
Table 2. Operating conditions
Symbol
VCC
VIC
Standby (pin 8)
6/30
Parameter
Value
Supply voltage
Common mode input voltage range
Threshold on pin 8 for TSH81
DocID009413 Rev 9
Unit
4.5 to 12
-
VCC to (VCC+ -1.1)
(VCC-) to (VCC+)
V
TSH80, TSH81, TSH82, TSH84
3
Electrical characteristics
Electrical characteristics
Table 3. Electrical characteristics at VCC+ = +5 V, VCC- = GND, Vic = 2.5 V, Tamb = 25 °C
(unless otherwise specified)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
10
12
mV
Input offset voltage
Tamb = 25 °C
Tmin < Tamb < Tmax
1.1
Input offset voltage drift vs.
temperature
Tmin < Tamb < Tmax
3
Iio
Input offset current
Tamb = 25 °C
Tmin < Tamb < Tmax
0.1
3.5
5
Iib
Input bias current
Tamb = 25 °C
Tmin < Tamb < Tmax
6
15
20
Cin
Input capacitance
ICC
Supply current per operator
Tamb = 25 °C
Tmin < Tamb < Tmax
CMR
Common mode rejection ratio
(ΔVic/ΔVio)
+0.1< Vic< 3.9 V and Vout = 2.5 V
Tamb = 25 °C
Tmin < Tamb < Tmax
SVR
Supply voltage rejection ratio Tamb = 25 °C
(ΔVCC/ΔVio)
Tmin < Tamb < Tmax
PSR
Power supply rejection ratio
(ΔVCC/ΔVout)
Positive and negative rail
Large signal voltage gain
RL = 150 Ω connected to 1.5 V and
Vout = 1 V to 4 V
Tamb = 25 °C
Tmin < Tamb < Tmax
75
70
84
|Source|
Vid = +1, Vout connected to 1.5 V
Tamb = 25 °C
Tmin < Tamb < Tmax
35
28
55
Sink
Vid = -1, Vout connected to 1.5 V
Tamb = 25 °C
Tmin < Tamb < Tmax
33
28
55
|Vio|
ΔVio/ΔT
Avd
Io
µV/°C
0.3
DocID009413 Rev 9
8.2
72
70
97
68
65
75
75
µA
pF
10.5
11.5
mA
dB
mA
7/30
Electrical characteristics
TSH80, TSH81, TSH82, TSH84
Table 3. Electrical characteristics at VCC+ = +5 V, VCC- = GND, Vic = 2.5 V, Tamb = 25 °C
(unless otherwise specified) (continued)
Symbol
Voh
Vol
GBP
Bw
SR
Parameter
High-level output voltage
Low-level output voltage
Gain bandwidth product
Test conditions
Tamb = 25 °C
RL = 150 Ω connected to GND
RL = 600 Ω connected to GND
RL = 2 kΩ connected to GND
RL = 10 kΩ connected to GND
RL = 150 Ω connected to 2.5 V
RL = 600 Ω connected to 2.5 V
RL = 2 kΩ connected to 2.5 V
RL = 10 kΩ connected to 2.5 V
Tmin < Tamb < Tmax
RL = 150 Ω connected to GND
RL = 150 Ω connected to 2.5 V
Min.
Typ.
4.2
4.36
4.85
4.90
4.93
4.66
4.90
4.92
4.93
4.60(1)
4.5
48
54
55
56
220
105
76
61
Slew rate
AVCL = +2
RL = 150 Ω // CL to 2.5 V
CL = 5 pF
CL = 30 pF
V
150
400
mV
200
450
F = 10 MHz
AVCL= +11
AVCL= -10
AVCL= +1
RL = 150 Ω connected to 2.5 V
Unit
4.1
4.4
Tamb = 25 °C
RL = 150 Ω connected to GND
RL = 600 Ω connected to GND
RL = 2 kΩ connected to GND
RL = 10 kΩ connected to GND
RL = 150 Ω connected to 2.5 V
RL = 600 Ω connected to 2.5 V
RL = 2 kΩ connected to 2.5 V
RL = 10 kΩ connected to 2.5 V
Tmin < Tamb < Tmax
RL = 150 Ω connected to GND
RL = 150 Ω connected to 2.5 V
Bandwidth at -3 dB
Max.
65
55
MHz
87
60
104
105
V/ms
φm
Phase margin
RL = 150 Ω // 30 pF to 2.5 V
40
Degree
en
Equivalent input noise
voltage
F = 100 kHz
11
nV/√ Hz
THD
Total harmonic distortion
AVCL= +2, F = 4 MHz
RL = 150 Ω // 30 pF to 2.5 V
Vout = 1Vpp
Vout = 2Vpp
-61
-54
IM2
AVCL = +2, Vout = 2 Vpp
Second order intermodulation RL = 150 Ω connected to 2.5 V
product
Fin1 = 180 kHz, Fin2 = 280 kHz
spurious measurement at 100 kHz
8/30
DocID009413 Rev 9
-76
dB
dBc
TSH80, TSH81, TSH82, TSH84
Electrical characteristics
Table 3. Electrical characteristics at VCC+ = +5 V, VCC- = GND, Vic = 2.5 V, Tamb = 25 °C
(unless otherwise specified) (continued)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
IM3
Third order intermodulation
product
AVCL = +2, Vout = 2 Vpp
RL = 150 Ω to 2.5 V
Fin1 = 180 kHz, Fin2 = 280 kHz
spurious measurement at 400 kHz
ΔG
Differential gain
AVCL = +2, RL = 150 Ω to 2.5 V
F = 4.5 MHz, Vout = 2 Vpp
0.5
%
Df
Differential phase
AVCL = +2, RL = 150 Ω to 2.5 V
F = 4.5 MHz, Vout = 2 Vpp
0.5
Degree
Gf
Gain flatness
F = DC to 6 MHz, AVCL = +2
0.2
F = 1 MHz to 10 MHz
65
Vo1/Vo2 Channel separation
-68
dBc
dB
1. Tested on the TSH80ILT device only.
DocID009413 Rev 9
9/30
Electrical characteristics
TSH80, TSH81, TSH82, TSH84
Table 4. Electrical characteristics at VCC+ = +5 V, VCC- = -5 V, Vic = GND, Tamb = 25 °C
(unless otherwise specified)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
10
12
mV
Input offset voltage
Tamb = 25 °C
Tmin < Tamb < Tmax
0.8
Input offset voltage drift vs.
temperature
Tmin < Tamb < Tmax
2
Iio
Input offset current
Tamb = 25 °C
Tmin < Tamb < Tmax
0.1
3.5
5
Iib
Input bias current
Tamb = 25 °C
Tmin < Tamb < Tmax
6
15
20
Cin
Input capacitance
ICC
Supply current per operator
Tamb = 25 °C
Tmin < Tamb < Tmax
CMR
Common mode rejection ratio
(ΔVic/ΔVio)
-4.9 < Vic < 3.9 V and Vout = GND
Tamb = 25 °C
Tmin < Tamb < Tmax
81
72
106
SVR
Supply voltage rejection ratio
(ΔVCC/ΔVio)
Tamb = 25 °C
Tmin < Tamb < Tmax
71
65
77
PSR
Power supply rejection ratio
(ΔVCC/ΔVout)
Positive and negative rail
Large signal voltage gain
RL = 150 Ω connected to GND and
Vout = -4 to +4
Tamb = 25 °C
Tmin < Tamb < Tmax
75
70
86
|Source|
Vid = +1, Vout connected to 1.5 V
Tamb = 25 °C
Tmin < Tamb < Tmax
35
28
55
Sink
Vid = -1, Vout connected to 1.5 V
Tamb = 25 °C
Tmin < Tamb < Tmax
30
28
55
4.2
High-level output voltage
Tamb = 25 °C
RL = 150 Ω connected to GND
RL = 600 Ω connected to GND
RL = 2 kΩ connected to GND
RL = 10 kΩ connected to GND
Tmin < Tamb < Tmax
RL = 150 Ω connected to GND
4.36
4.85
4.9
4.93
|Vio|
ΔVio/ΔT
Avd
Io
Voh
Vol
10/30
Low-level output voltage
µV/°C
0.7
9.8
µA
pF
12.3
13.4
mA
dB
Tamb = 25 °C
RL = 150 Ω connected to GND
RL = 600 Ω connected to GND
RL = 2 kΩ connected to GND
RL = 10 kΩ connected to GND
Tmin < Tamb < Tmax
RL = 150 Ω connected to GND
DocID009413 Rev 9
75
mA
V
4.1
-4.63
-4.86
-4.9
-4.93
-4.4
mV
-4.3
TSH80, TSH81, TSH82, TSH84
Electrical characteristics
Table 4. Electrical characteristics at VCC+ = +5 V, VCC- = -5 V, Vic = GND, Tamb = 25 °C
(unless otherwise specified) (continued)
Symbol
GBP
Bw
SR
Parameter
Gain bandwidth product
Test conditions
Min.
F = 10 MHz
AVCL = +11
AVCL = -10
Bandwidth at -3 dB
AVCL = +1
RL = 150 Ω // 30 pF to GND
Slew rate
AVCL = +2
RL = 150 Ω // CL to GND
CL = 5 pF
CL = 30 pF
RL = 150 Ω connected to GND
fm
Phase margin
en
Equivalent input noise voltage F = 100 kHz
AVCL = +2, F = 4 MHz
RL = 150 Ω // 30 pF to GND
Vout = 1 Vpp
Vout = 2 Vpp
Typ.
65
55
Max.
Unit
MHz
100
68
117
118
V/µs
40
Degree
11
nV/√ Hz
THD
Total harmonic distortion
IM2
AVCL = +2, Vout = 2 Vpp
Second order intermodulation RL = 150 Ω to GND
product
Fin1 = 180 kHz, Fin2 = 280 kHz
spurious measurement at 100 kHz
-76
IM3
Third order intermodulation
product
AVCL = +2, Vout = 2 Vpp
RL = 150 Ω to GND
Fin1 = 180 kHz, Fin2 = 280 kHz
spurious measurement at 400 kHz
-68
ΔG
Differential gain
AVCL = +2, RL = 150 Ω to GND
F = 4.5 MHz, Vout = 2 Vpp
0.5
%
Df
Differential phase
AVCL = +2, RL = 150 Ω to GND
F = 4.5 MHz, Vout = 2 Vpp
0.5
Degree
Gf
Gain flatness
F = DC to 6 MHz, AVCL = +2
0.2
Channel separation
F = 1 MHz to 10 MHz
65
Vo1/Vo2
DocID009413 Rev 9
-61
-54
dB
dBc
dB
11/30
Electrical characteristics
TSH80, TSH81, TSH82, TSH84
Table 5. Standby mode - VCC+, VCC-, Tamb = 25 °C (unless otherwise specified)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Vlow
Standby low level
VCC-
(VCC- +0.8)
Vhigh
Standby high level
(VCC- +2)
(VCC+)
Current consumption per
operator when standby is active
Pin 8 (TSH81) to VCC-
20
Zout
Output impedance (Rout//Cout)
Rout
Cout
10
17
Ton
Time from standby mode to
active mode
Toff
Time from active mode to
standby mode
ICC-STBY
V
µA
MΩ
pF
2
µs
Down to ICC-STBY = 10 µA
10
Table 6. TSH81 standby control pin status
12/30
55
Unit
TSH81 standby control pin 8 (STANDBY)
Operator status
Vlow
Standby
Vhigh
Active
DocID009413 Rev 9
TSH80, TSH81, TSH82, TSH84
Electrical characteristics
Figure 2. Closed loop gain and phase vs.
frequency (gain = +2, VCC = ±2.5 V)
RL = 150 Ω, Tamb = 25 °C
Figure 3. Overshoot vs. output capacitance
(VCC = ±2.5 V)
Gain = +2, Tamb = 25 °C
10
200
10
150Ω//33pF
150
Ω // 33 pF
150Ω//22pF
150
Ω // 22 pF
5
Gain
100
150Ω//10pF
150
Ω // 10 pF
Ph ase (°)
0
-5
Phase
150
Ω
150Ω
Gain (dB)
Gain (dB)
5
0
0
-100
-10
-15
-200
1E+4
1E+5
1E+6
1E+7
1E+8
-5
1E+9
1E+6
Frequency (Hz)
1E+7
1E+8
1E+9
Freq uen cy (Hz)
Figure 4. Closed loop gain and phase vs.
frequency (gain = -10, VCC = ±2.5 V)
Figure 5. Closed loop gain and phase vs.
frequency (gain = +11, VCC = ±2.5 V)
RL = 150 Ω, Tamb = 25 °C
RL = 150 Ω , Tamb = 25 °C
30
200
30
Phase
0
Ph as e
Phase
150
20
20
Phase (°)
50
Gain (dB)
10
-50
Gain
Gain
Phase (°)
Gain (dB)
100
Gain
10
-100
0
0
0
-50
- 10
-10
1E+4
1E+5
1E+7
1E+6
1E+8
-150
1E+4
-100
1E+9
1E+5
1E+6
1E+7
1E+8
1E+9
Frequency (Hz)
Frequency (Hz)
Figure 6. Large signal measurement – positive Figure 7. Large signal measurement – negative
slew rate (VCC = ±2.5 V)
slew rate (VCC = ±2.5 V)
Gain = +2, ZL = 150 Ω //5.6 pF, Vin = 400 mVpk
Gain = +2, ZL = 150 Ω //5.6 pF, Vin = 400 mVpk
3
2
2
1
1
Vout (V )
Vout (V)
3
0
-1
0
-1
-2
-2
-3
0
10
20
30
40
50
60
70
80
-3
Ti me (ns)
0
10
20
30
40
50
60
70
Time (ns)
DocID009413 Rev 9
13/30
Electrical characteristics
TSH80, TSH81, TSH82, TSH84
Figure 9. Small signal measurement – fall time
(VCC = ±2.5 V)
Gain = +2, RL = 150 Ω, Vin = 400 mVpk
Gain = +2, RL = 150 Ω , Vin = 400 mVpk
0.06
0.06
0.04
0.04
0.02
0.02
0
Vout
Vin
-0.02
Vin ,Vout (V)
Vin, Vout (V)
Figure 8. Small signal measurement – rise time
(VCC = ±2.5 V)
Vout
Vin
0
- 0.02
-0.04
-0.04
-0.06
-0.06
0
10
20
30
40
50
60
0
10
20
Time (ns)
30
40
50
60
Time (ns)
Figure 10. Channel separation (crosstalk) vs.
frequency schematic (VCC = ±2.5 V)
Figure 11. Channel separation (crosstalk) vs.
frequency (VCC = ±2.5 V)
Measurement configuration: crosstalk = 20 log (V0/V1)
Gain = +11, ZL = 150 Ω //27 pF
-20
-30
-40
4/1
output
4/1output
Xtalk (dB)
-50
3/1
output
3/1output
-60
-70
-80
2/1output
2/1
output
-90
-100
-110
1E+4
1E+5
1E+6
1E+7
Frequency (Hz)
Figure 12. Equivalent input noise voltage
(VCC = ±2.5 V)
Figure 13. Maximum output swing
(VCC = ±2.5 V)
Gain = +100, no load
Gain = +11, RL = 150 Ω
30
3
2
+
_
Vin,Vout (V)
en (nV/
Hz)
25
20
15
10
Vin
0
-1
-2
5
0.1
1
10
100
1000
-3
0.0E+0
5.0E-2
1. 0E-1
Time (ms)
Frequency (kHz)
14/30
Vout
1
DocID009413 Rev 9
1.5 E- 1
2.0E-1
TSH80, TSH81, TSH82, TSH84
Electrical characteristics
Figure 14. Standby mode - Ton, Toff
(VCC = ±2.5 V)
Open loop
Figure 15. Third order intermodulation
(VCC = ±2.5 V)(1)
Gain = +2, ZL = 150 Ω //27 pF, Tamb = 25 °C
0
3
-10
-20
2
0
Vout
-1
-40
IM3 (dBc)
V in, Vout (V)
-30
1
7 40kHz
740
kHz
-50
80kHz
80
kHz
-60
-70
-2
-80
-3
Ton
0
2 E-6
Standby
4E-6
-90
Toff
6E-6
8 E-6
1E-5
640kHz
640
kHz
380kHz
380
kHz
-100
0
time (s)
1
2
3
4
Vout peak(V)
1. The IFR2026 synthesizer generates a two-tone signal (F1 = 180 kHz, F2 = 280 kHz), each tone having the same
amplitude. The HP3585 spectrum analyzer measures the intermodulation products as a function of the output voltage. The
generator and the spectrum analyzer are phase locked for better accuracy.
Figure 16. Group delay (VCC = ±2.5 V)
Gain = +2, ZL = 150 Ω //27 pF, Tamb = 25 °C
DocID009413 Rev 9
15/30
Electrical characteristics
TSH80, TSH81, TSH82, TSH84
Figure 17. Closed loop gain and phase vs.
frequency (gain = +2, VCC = ±5 V)
Figure 18. Overshoot vs. output capacitance
(VCC = ±5 V)
Gain = +2, Tamb = 25 °C
RL = 150 Ω , Tamb = 25 °C
10
20
200
150Ω//33pF
150
W // 33 pF
5
10
Gain
150Ω//22p
150
Ω // F22 pF
100
150Ω//10pF
150
Ω // 10 pF
0
Phase
-10
Gain (dB)
-5
Phase (°)
Gain (dB)
0
0
150
Ω
150Ω
-10
-100
-20
-15
-20
1E+4
1E+5
1E+6
1E+7
1E+8
-200
1E+9
-30
1E+4
1E+5
Frequency (Hz)
1E+6
1E+7
1E+8
1E+9
Frequency (Hz)
Figure 19. Closed loop gain and phase vs.
frequency (gain = -10, VCC = ±5 V)
Figure 20. Closed loop gain and phase vs.
frequency (gain = +11, VCC = ±5 V)
RL = 150 Ω , Tamb = 25 °C
RL = 150 Ω , Tamb = 25 °C
20 0
30
30
0
Phase
Phase
Phase
15 0
10
50
-50
Gain
Phase (°)
10 0
Gain
Gain
Gain (dB)
20
Phase (°)
Gain (dB)
20
10
-100
0
0
0
- 10
-10
1E+4
-5 0
1E+4
1E+5
1 E+6
1E+7
1 E+8
1E+9
1E+5
1E+6
1E+7
1E+8
-150
1E+9
Frequency (Hz)
Frequency (Hz)
Figure 21. Large signal measurement - positive Figure 22. Large signal measurement - negative
slew rate (VCC = ±5 V)
slew rate (VCC = ±5 V)
Gain = +2, ZL = 150 Ω //5.6 pF, Vin = 400 mVpk
5
5
4
4
3
3
2
2
1
Vout (V)
Vout (V)
Gain = +2, ZL = 150 Ω //5.6 pF, Vin = 400 mVpk
0
-1
-1
-2
-2
-3
-3
-4
-4
-5
-5
0
20
40
60
80
100
0
20
40
60
Time (ns)
Time (ns)
16/30
1
0
DocID009413 Rev 9
80
100
TSH80, TSH81, TSH82, TSH84
Electrical characteristics
Figure 23. Small signal measurement - rise time Figure 24. Small signal measurement - fall time
(VCC = ±5 V)
(VCC = ±5 V)
Gain = +2, RL = 150 Ω , Vin = 400 mVpk
0.0 6
0.06
0.0 4
0.04
0.0 2
0.02
0
Vin, Vout ( V)
Vin, Vout ( V)
Gain = +2, RL = 150 Ω , Vin = 400 mVpk
Vout
V in
- 0 .02
Vout
Vin
0
-0.02
-0.04
- 0 .04
-0.06
- 0 .06
0
10
20
30
40
50
0
60
10
20
30
40
50
60
Time (ns)
Ti m e (ns)
Figure 25. Channel separation (crosstalk) vs.
frequency schematic (VCC = ±5 V)
Figure 26. Channel separation (crosstalk) vs.
frequency (VCC = ±5 V)
Gain = +11, ZL = 150 Ω //27 pF
Measurement configuration: crosstalk = 20 log (V0/V1)
-2 0
-3 0
-4 0
output
4/14/1output
-5 0
3/1output
3/1
output
Xtalk (dB)
-6 0
-7 0
-8 0
2/1out
put
2/1
output
-9 0
-1 00
-110
1E+4
1E+5
1E+6
1E+7
Frequency (Hz)
Figure 27. Equivalent input noise voltage
(VCC = ±5 V)
Figure 28. Maximum output swing
(VCC = ±5 V)
Gain = +11, RL = 150 Ω
Gain = +100, no load
5
30
4
25
3
+
_
Vout
Vin, Vout (V)
en (nV /
Hz)
2
20
15
10
1
Vin
0
-1
-2
-3
-4
5
0.1
1
10
100
1000
-5
0.0E+0
Frequency (kHz)
5.0E-2
1.0E-1
1.5E-1
20
. E-1
Time (ms)
DocID009413 Rev 9
17/30
Electrical characteristics
TSH80, TSH81, TSH82, TSH84
Figure 29. Standby mode - Ton, Toff
(VCC = ±5 V)
Figure 30. Third order intermodulation
(VCC = ±5 V)(1)
Open loop
Gain = +2, ZL = 150 Ω //27 pF, Tamb = 25 °C
0
-10
5
-20
-40
IM3 (dBc)
Vin, Vout (V)
-30
Vout
0
80kHz
80 kHz
-50
740740kHz
kHz
-60
-70
-80
-5
Ton
-90
Toff
Standby
0
2E-6
4E-6
6E- 6
8E-6
380kHz
380
kHz
640kHz
640
kHz
-10 0
0
1
2
3
4
Vout peak(V)
time (s)
1. The IFR2026 synthesizer generates a two-tone signal (F1 = 180 kHz, F2 = 280 kHz), each tone having the same
amplitude. The HP3585 spectrum analyzer measures the intermodulation products as a function of the output voltage. The
generator and the spectrum analyzer are phase locked for better accuracy.
Figure 31. Group delay (VCC = ±5 V)
Gain = +2, ZL = 150 Ω //27 pF, Tamb = 25 °C
18/30
DocID009413 Rev 9
TSH80, TSH81, TSH82, TSH84
4
Test conditions
4.1
Layout precautions
Test conditions
To make the best use of the TSH8x circuits at high frequencies, some precautions have to
be taken with regard to the power supplies.
•
In high-speed circuit applications, the implementation of a proper ground plane on both
sides of the PCB is mandatory to ensure low inductance and low resistance common
return.
•
Power supply bypass capacitors (4.7 µF and ceramic 100 pF) should be placed as
close as possible to the IC pins in order to improve high frequency bypassing and
reduce harmonic distortion. The power supply capacitors must be incorporated for both
the negative and positive pins.
•
All inputs and outputs must be properly terminated with output resistors. Thus, the
amplifier load is resistive only and the stability of the amplifier is improved.
All leads must be wide and must be as short as possible, especially for op-amp inputs
and outputs, in order to decrease parasitic capacitance and inductance.
•
Time constants result from parasitic capacitance. To reduce time constants in lowergain applications, use a low feedback resistance (under 1 kΩ).
•
Choose the smallest component size possible (SMD).
•
On the output, the load capacitance must be negligible to maintain good stability. Place
ca serial resistance as close as possible to the output pin to minimize the effect of the
load capacitance.
Figure 32. CCIR330 video line
DocID009413 Rev 9
19/30
Test conditions
4.2
TSH80, TSH81, TSH82, TSH84
Video capabilities
To characterize the differential phase and differential gain, a CCIR330 video line is used.
The video line contains of five (flat) levels of luminance onto which the chrominance signal
is superimposed. The luminance gives various amplitudes which define the saturation of the
signal. The chrominance gives various phases which define the color of the signal.
Differential phase (or differential gain) distortion is present if a signal chrominance phase
(gain) is affected by the luminance level. The differential phase and gain represent the
ability to uniformly process the high frequency information at all luminance levels.
When a differential gain is present, color saturation is not correctly reproduced.
The input generator is the Rohde & Schwarz CCVS. The output measurement is made by
the Rohde and Schwarz VSA.
Figure 33. Measurement on Rohde and Schwarz VSA
20/30
DocID009413 Rev 9
TSH80, TSH81, TSH82, TSH84
Test conditions
Table 7. Video results
Parameter
Value (VCC = ±2.5 V)
Value (VCC = ±5 V)
Lum NL
0.1
0.3
Lum NL Step1
100
100
Lum NL Step2
100
99.9
Lum NL Step3
99.9
99.8
Lum NL Step4
99.9
99.9
Lum NL Step5
99.9
99.7
Diff Gain pos
0
0
Diff Gain neg
-0.7
-0.6
Diff Gain pp
0.7
0.6
Diff Gain Step1
-0.5
-0.3
Diff Gain Step2
-0.7
-0.6
Diff Gain Step3
-0.3
-0.5
Diff Gain Step4
-0.1
-0.3
Diff Gain Step5
-0.4
-0.5
Diff Phase pos
0
0.1
Diff Phase neg
-0.2
-0.4
Diff Phase pp
0.2
0.5
Diff Phase Step1
-0.2
-0.4
Diff Phase Step2
-0.1
-0.4
Diff Phase Step3
-0.1
-0.3
Diff Phase Step4
0
0.1
Diff Phase Step5
-0.2
-0.1
DocID009413 Rev 9
Unit
%
Degree
21/30
Precautions on asymmetrical supply operation
5
TSH80, TSH81, TSH82, TSH84
Precautions on asymmetrical supply operation
The TSH8x device can be used with either a dual or a single supply. If a single supply is
used, the inputs are biased to the mid-supply voltage (+VCC/2). This bias network must be
carefully designed so as to reject any noise present on the supply rail.
As the bias current is 15 µA, use a high resistance R1 (approximately 10 kΩ) to avoid
introducing an offset mismatch at the amplifier’s inputs.
Figure 34. Asymmetrical supply schematic diagram
IN Cin
Cout OUT
+
Vcc+
-
R1
R5
R2
R3
C3
RL
Cf
C1
C2
R4
AM00845
C1, C2, C3 are bypass capacitors intended to filter perturbations from VCC. The following
capacitor values are appropriate:
C1 = 100 nF and C2 = C3 = 100 µF
R2 and R3 are such that the current running through them must be superior to 100 times the
bias current. Therefore, use the following resistance values:
R2 = R3 = 4.7 kΩ
Cin and Cout are chosen to filter the DC signal by the low-pass filters (R1, Cin) and
(Rout, Cout). With R1 = 10 kΩ, Rout = RL = 150 Ω, and Cin = 2 µF, Cout = 220 µF the cutoff
frequency obtained is lower than 10 Hz.
Figure 35. Use of the TSH8x in a gain = -1 configuration
IN
-
OUT
+
R1
R2
R3
C3
C1
C2
AM00846
22/30
DocID009413 Rev 9
TSH80, TSH81, TSH82, TSH84
6
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
DocID009413 Rev 9
23/30
Package information
6.1
TSH80, TSH81, TSH82, TSH84
SOT23-5 package information
Figure 36. SOT23-5 package outline
Table 8. SOT23-5 package mechanical data
Dimensions
Symbol
A
Millimeters
Min.
Typ.
Max.
Min.
Typ.
Max.
0.90
1.20
1.45
0.035
0.047
0.057
A1
24/30
Inches
0.15
0.006
A2
0.90
1.05
1.30
0.035
0.041
0.051
B
0.35
0.40
0.50
0.013
0.015
0.019
C
0.09
0.15
0.20
0.003
0.006
0.008
D
2.80
2.90
3.00
0.110
0.114
0.118
D1
1.90
0.075
e
0.95
0.037
E
2.60
2.80
3.00
0.102
0.110
0.118
F
1.50
1.60
1.75
0.059
0.063
0.069
L
0.10
0.35
0.60
0.004
0.013
0.023
K
0°
10°
DocID009413 Rev 9
TSH80, TSH81, TSH82, TSH84
6.2
Package information
SO8 package information
Figure 37. SO8 package outline
62
Table 9. SO8 package mechanical data
Dimensions
Symbol
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.75
0.069
A1
0.10
A2
1.25
b
0.28
0.48
0.011
0.019
c
0.17
0.23
0.007
0.010
D
4.80
4.90
5.00
0.189
0.193
0.197
E
5.80
6.00
6.20
0.228
0.236
0.244
E1
3.80
3.90
4.00
0.150
0.154
0.157
e
0.25
Max.
0.004
0.010
0.049
1.27
0.050
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
L1
k
ccc
1.04
1°
0.040
8°
0.10
DocID009413 Rev 9
1°
8°
0.004
25/30
Package information
6.3
TSH80, TSH81, TSH82, TSH84
TSSOP8 package information
Figure 38. TSSOP8 package outline
76623
Table 10. TSSOP8 package mechanical data
Dimensions
Symbol
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.20
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
1.05
0.031
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.008
D
2.90
3.00
3.10
0.114
0.118
0.122
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.177
e
0°
L
0.45
aaa
1.00
0.65
k
L1
26/30
Inches
0.60
0.006
0.039
0.041
0.0256
8°
0°
0.75
0.018
1
8°
0.024
0.030
0.039
0.10
DocID009413 Rev 9
0.004
TSH80, TSH81, TSH82, TSH84
6.4
Package information
TSSOP14 package information
Figure 39. TSSOP14 package outline
76623
Table 11. TSSOP14 package mechanical data
Dimensions
Symbol
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.20
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.90
5.00
5.10
0.193
0.197
0.201
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.176
e
L
0.65
0.45
L1
k
aaa
1.00
0.60
0.0256
0.75
0.018
1.00
0°
0.024
0.030
0.039
8°
0.10
DocID009413 Rev 9
0°
8°
0.004
27/30
Ordering information
7
TSH80, TSH81, TSH82, TSH84
Ordering information
Table 12. Order codes
Type
Temperature
range
TSH80ILT
Package
Packaging
SOT23-5
K303
TSH80IYLT(1)
SOT23-5
(automotive grade level)
K310
TSH80IYDT(1)
SO8
(automotive grade level)
TSH81IPT
TSH82IDT
TSH82IYDT(1)
-40 to +85 °C
Tape and reel
SH80IY
TSSOP8
SO8
SH81I
Tape and reel
SO8
(automotive grade level)
TSH82IPT
TSSOP8
TSH84IPT
TSSOP14
DocID009413 Rev 9
TSH82I
TSH82IY
Tape and reel
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening
according to AEC Q001 and Q002 or equivalent.
28/30
Marking
SH82I
SH84I
TSH80, TSH81, TSH82, TSH84
8
Revision history
Revision history
Table 13. Document revision history
Date
Revision
1-Feb-2003
1
First release.
2-Aug-2005
2
PPAP references inserted in the datasheet, see Table 12: Order
codes on page 28.
12-Apr-2007
3
Corrected temperature range for TSH80IYD/IYDT and
TSH82IYD/IYDT order codes in Table 12: Order codes on page 28.
24-Oct-2007
4
TSH81IYPT PPAP references inserted in the datasheet, see
Table 12: Order codes on page 28.
19-May-2009
5
Added data relating to the quad TSH84 device.
Removed TSH81IYPT, TSH81IYD-IYDT, TSH82IYPT and
TSH82IYD-IYDT order codes in Table 12: Order codes.
6
Added TSSOP14 package to figure on page 1, updated titles of
Figure 2 to Figure 31, updated Section 6: Package information,
removed TSH80ID-IDT, TSH80IYD, TSH81ID-IDT and TSH82ID
order codes from Table 12: Order codes. Modified note 1 below
Table 12: Order codes, minor corrections throughout document.
7
Updated TSH80IYLT order code (status qualified) in Table 12.
Removed TSH80IYD, TSH80IYDT, TSH80ID/DT, TSH81ID/DT, and
TSH82ID order code from Table 12.
Replaced TSH82DT by TSH82IDT order code in Table 12.
Minor corrections throughout document.
30-Apr-2013
8
Updated Features: added automotive qualification
Figure 1: Pin connections for each package (top view): updated pin
connections of SO8/TSSOP8 packages for TSH81 device.
Replaced Figure 36: SOT23-5 package outline
Table 12: Order codes: added automotive order code TSH82IYDT
03-Jul-2014
9
Updated CDM to 1.5 kV in Table 1: Absolute maximum ratings
Table 12: Order codes: added automotive order code TSH80IYDT
and removed shipping option in tubes from TSH82IDT
24-Jul-2012
13-Sep-2012
Changes
DocID009413 Rev 9
29/30
TSH80, TSH81, TSH82, TSH84
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
30/30
DocID009413 Rev 9