TSM109_04

TSM109/A Dual Comparator and Voltage Reference COMPARATOR s s s s s s s Low supply current (1.1ma) independent of supply voltage Low input bias current: 25nA typ Low input offset voltage: ±1mV typ Input common-mode voltage range includes ground Low output saturation voltage: 250mV typ (Io = 4mA) Differential input voltage range equal to the supply voltage Wide power supply range: ±1V to ±18V Package Reference N DIP-8 VOLTAGE REFERENCE s s s Fixed Vref to 2.5V 0.4% and 1% voltage precision Sink current capability: 1 to 100mA D SO-8 ORDER CODE Part Number TSM109 TSM109A DESCRIPTION The TSM109 is a monolithic IC that includes two comparators and a shunt voltage reference. This device offers space and cost savings in many applications including power supply management or data acquisition systems. Temperature Range -40°C, +105°C -40°C, +105°C Package N • • D • • Note: N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) PIN CONNECTIONS (top view) 1 Out Vcc 8 2 Vref Out 7 3 Ve+ Ve- 6 4 Gnd Ve+ 5 February 2004 1/7 TSM109/A 1 ABSOLUTE MAXIMUM RATINGS Parameter Supply voltage Input Voltage Continuous Cathode current range Maximum Junction Temperature Thermal Resistance Junction to Ambient (SO package) Electrostatic Discharge Protection Absolute Maximum Ratings Symbol VCC Vin Ik Tj Rthja ESD Value 36 -0.3 to Vcc +0.3 -100 to 150 150 175 1.5 Unit V V mA °C °C/W kV OPERATING CONDITIONS Symbol Vcc Toper DC Supply Conditions Operational temperature Parameter Value 2 to 36 -40 to105 Unit V °C ELECTRICAL CHARACTERISTICS VCC+ = 5V, VCC- = 0V, Tamb = 25°C (unless otherwise specified) Symbol ICC Parameter Total Supply Current, excluding current in the Voltage Reference VCC = +5V, no load VCC = +30V, no load Min Typ Max Unit 0.4 1 1 2.5 mA 2/7 Electrical Characteristics 2 ELECTRICAL CHARACTERISTICS TSM109/A COMPARATOR (independent comparator) VCC+ = +5V, VCC-= GND, Tamb = +25°C (unless otherwise specified) Symbo l Vio Input Offset Voltage - note 1 Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Offset Current Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Bias Current (I+ or I-) - note 2 Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Large Signal Voltage Gain VCC = 15V, RL = 15kΩ, Vo = 1V to 11V Input Common Mode Voltage Range - note 3 VCC = 30V Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Differential Input Voltage -note 4 Low Level Output Voltage Vid = -1V, Isink = 4mA Tamb = +25°C Tmin ≤ Tamb ≤ Tmax High Level Output Current (Vid = 1V) IOH VCC = Vo = 30V Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Output Sink Currrent Vid= 1V, Vo = 1.5V Response Time - note RL= 5.1kΩ connected to VCC+ Large Signal Response Time RL= 5.1kΩ connected to VCC+, el = TTL, V(ref) = +1.4v 5 TSM109 Parameter Min. Typ. 1 Unit Max. 5 9 25 100 250 400 mV Iio 3 nA Iib 25 nA Avd 50 200 V/mV Vicm 0 0 VCC+ -1.5 VCC+ -2 VCC+ V Vid VOL 250 400 700 mV 30 150 1 nA µA mA Isink tre 10 20 1.3 µs trel 300 ns 1) 2) 3) 4) At output switch point, Vo ≈ 1.4V, Rs = 0 with VCC + from 5V to 30V, and over the full common-mode range (0V to VCC+ -1.5V). The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output, so no loading charge exists on the reference of input lines. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ -1.5V. Positive voltage excursions of one input may exceed the power supply level. As long as the other input voltage remains within the common-mode range, the comparator will provide an appropriate output state. The low input voltage state must not be less than -0.3V (or 0.3V below the negative power supply, if used). The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals, 300ns can be obtained 5) 3/7 TSM109/A Electrical Characteristics COMPARATOR (comparator with inverting input connected to the internal Vref)) VCC+ = +5V, VCC-= GND, Tamb = +25°C (unless otherwise specified) Symbo l Vio Input Offset Voltage - note 1 Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Bias Current for positive input note 2 Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Large Signal Voltage Gain VCC = 15V, RL = 15kΩ, Vo = 1V to 11V Differential Input Voltage -note 50 TSM109 Parameter Min. Typ. 1 Unit Max. 5 9 250 400 mV Iib 25 nA Avd Vid 200 VCC+ -2.5V V/mV V VOL Low Level Output Voltage Vid = -1V, Isink = 4mA Tamb = +25°C Tmin ≤ Tamb ≤ Tmax High Level Output Current (Vid = 1V) VCC = Vo = 30V Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Output Sink Currrent Vid= 1V, Vo = 1.5V Response Time - note RL= 5.1kΩ connected to VCC+ Large Signal Response Time RL= 5.1kΩ connected to VCC+, el = TTL, V(ref) = +1.4v 3 250 400 700 mV IOH 30 150 1 nA µA mA Isink tre 10 20 1.3 µs trel 300 ns 1) 2) 3) At output switch point, Vo ≈ 1.4V, Rs = 0 with VCC + from 5V to 30V, and over the full common-mode range (0V to VCC+ -1.5V). The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output, so no loading charge exists on the reference of input lines. The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals, 300ns can be obtained. 4/7 Electrical Characteristics ELECTRICAL CHARACTERISTICS VOLTAGE REFERENCE Symbol IK Cathode Current TSM109/A Conditions Value 1 to 100 Unit mA Tamb = 25°C (unless otherwise specified) Symbo l TSM109A Parameter Min. Reference Input Voltage, IK = 10 mA Tamb = 25°C Tmin ≤ Tamb ≤ Tmax Reference Input Voltage Deviation OverTemperature Range IK = 10 mA Tmin ≤Tamb ≤ Tmax TSM109 Unit Typ. Max. V Typ. Max. Min. Vref 2.490 2.500 2.510 2.475 2.500 2.525 2.48 2.52 2.45 2.55 ∆Vref 7 30 7 30 mV Temperature Coefficient of Reference Input Voltage IK = 10 mA, ∆ Vref ------------------- Tmin ≤Tamb ≤ Tmax Vref ∆ T Imin |ZVref| Minimum Cathode Current for Regulation Dynamic Impedance - note ∆Vref, ∆IK = 1 to 100mA, f < 1KHz 1 ±13 0.5 0.3 ±90 1 0.65 ±13 0.5 0.3 ±90 1 0.65 ppm/°C mA Ω 1) The dynamic impedance is defined as [Z Vref| = ∆VVref/∆IK 5/7 TSM109/A 3 PACKAGE MECHANICAL DATA PACKAGE MECHANICAL DATA Plastic DIP-8 MECHANICAL DATA mm. DIM. MIN. A a1 B B1 b b1 D E e e3 e4 F I L Z 0.44 3.3 1.6 0.017 8.8 2.54 7.62 7.62 7.1 4.8 0.130 0.063 0.38 0.7 1.39 0.91 0.5 0.5 9.8 0.346 0.100 0.300 0.300 0.280 0.189 0.015 1.65 1.04 TYP 3.3 0.028 0.055 0.036 0.020 0.020 0.386 0.065 0.041 MAX. MIN. TYP. 0.130 MAX. inch P001F 6/7 PACKAGE MECHANICAL DATA PACKAGE MECHANICAL DATA SO-8 MECHANICAL DATA DIM. A A1 A2 B C D E e H h L k ddd 0.1 5.80 0.25 0.40 mm. MIN. 1.35 0.10 1.10 0.33 0.19 4.80 3.80 1.27 6.20 0.50 1.27 8˚ (max.) 0.04 0.228 0.010 0.016 TYP MAX. 1.75 0.25 1.65 0.51 0.25 5.00 4.00 MIN. 0.053 0.04 0.043 0.013 0.007 0.189 0.150 0.050 0.244 0.020 0.050 inch TYP. MAX. 0.069 0.010 0.065 0.020 0.010 0.197 0.157 TSM109/A 0016023/C Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners. © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain Sweden - Switzerland - United Kingdom - United States http://www.st.com 7/7