TSV612AIST

TSV611, TSV611A, TSV612, TSV612A Rail-to-rail input/output 10 µA, 120 kHz CMOS operational amplifiers Features ■ ■ ■ ■ ■ ■ ■ ■ Rail-to-rail input and output Low power consumption: 10 µA typ at 5 V Low supply voltage: 1.5 to 5.5 V Gain bandwidth product: 120 kHz typ Unity gain stable Low input offset voltage: 800 µV max (A version) Low input bias current: 1 pA typ Temperature range: -40 to +85° C TSV611ILT - TSV611ICT In+ 1 VCC- 2 In- 3 + _ 5 VCC+ 4 Out SOT23-5/SC70-5 TSV612IST - TSV612ID/DT Out1 In1In1+ VCC1 2 3 4 _ + _ + 8 7 6 5 VCC+ Out2 In2In2+ Applications ■ ■ ■ ■ ■ ■ ■ Battery-powered applications Smoke detectors Proximity sensors Portable devices Signal conditioning Active filtering Medical instrumentation MiniSO-8/SO-8 Description The TSV61x family of single and dual operational amplifiers offers low voltage, low power operation and rail-to-rail input and output. The devices also feature an ultra-low input bias current as well as a low input offset voltage. The TSV61x have a gain bandwidth product of 120 kHz while consuming only 10 µA at 5 V. These features make the TSV61x family ideal for sensor interfaces, battery supplied and portable applications, as well as active filtering. January 2010 Doc ID 15768 Rev 2 1/19 www.st.com 19 Absolute maximum ratings and operating conditions TSV611, TSV611A, TSV612, TSV612A 1 Absolute maximum ratings and operating conditions Table 1. Symbol VCC Vid Vin Tstg Supply voltage (1) (2) Absolute maximum ratings Parameter Value 6 ±VCC VCC- -0.2 to VCC++0.2 -65 to +150 (4)(5) Unit V V V °C Differential input voltage Input voltage (3) Storage temperature Thermal resistance junction to ambient SC70-5 205 250 190 125 150 4 200 1.5 200 °C kV V kV mA model(6) model(8) °C/W Rthja SOT23-5 MiniSO-8 SO-8 Tj ESD Maximum junction temperature HBM: human body MM: machine model(7) CDM: charged device Latch-up immunity 1. All voltage values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. Vcc-Vin must not exceed 6 V. 4. Short-circuits can cause excessive heating and destructive dissipation. 5. Rth are typical values. 6. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 7. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating. 8. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to ground. Table 2. Symbol VCC Vicm Toper Operating conditions Parameter Supply voltage Common mode input voltage range Operating free air temperature range Value 1.5 to 5.5 VCC- -0.1 to VCC+ +0.1 -40 to +85 Unit V V °C 2/19 Doc ID 15768 Rev 2 TSV611, TSV611A, TSV612, TSV612A Electrical characteristics 2 Electrical characteristics Table 3. Electrical characteristics at VCC+ = +1.8 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25° C, and RL connected to VCC/2 (unless otherwise specified) Parameter Conditions Min. Typ. Max. Unit Symbol DC performance TSV61x TSV61xA Vio Offset voltage Tmin. < Top < Tmax. TSV61x Tmin. < Top < TmaxTSV61xA Input offset voltage drift Input offset current (Vout = Vcc/2) Input bias current (Vout = Vcc/2) Common mode rejection ratio 20 log (ΔVic/ΔVio) 2 1 Tmin. < Top < Tmax. 1 1 Tmin. < Top < Tmax. 0 V to 1.8 V, Vout = 0.9 V Tmin. < Top < Tmax. , RL = 10 kΩ Vout = 0.5 V to 1.3 V Tmin. < Top < Tmax. VOH VOL High level output voltage Low level output voltage Isink Iout Isource Supply current (per operator) RL = 10 kΩ Tmin. < Top < Tmax. RL = 10 kΩ Tmin. < Top < Tmax. Vo = 1.8 V Tmin. < Top < Tmax. Vo = 0 V Tmin. < Top < Tmax. No load, Vout = Vcc/2 Tmin. < Top < Tmax. 9 9 8 8 6.5 6 55 53 78 74 35 50 4 7 13 83 1 71 4 0.8 mV 5 2 μV/°C 10 (1) DVio Iio pA pA pA pA dB dB dB dB mV 100 10(1) 100 Iib CMR Avd Large signal voltage gain 35 50 mV mA 10 9 12 12.5 µA µA ICC AC performance GBP φm Gm SR Gain bandwidth product Phase margin Gain margin Slew rate RL = 10 kΩ CL = 20 pF , RL = 10 kΩ, CL = 20 pF RL = 10 kΩ, CL = 20 pF RL = 10 kΩ, CL = 20 pF, Vout = 0.5V to 1.3V 100 60 9.5 0.03 kHz Degrees dB V/μs Doc ID 15768 Rev 2 3/19 Electrical characteristics Table 3. TSV611, TSV611A, TSV612, TSV612A Electrical characteristics at VCC+ = +1.8 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25° C, and RL connected to VCC/2 (unless otherwise specified) (continued) Parameter Equivalent input noise voltage Total harmonic distortion + noise Conditions f = 1 kHz Fin = 1 kHz, Av = 1, Vout = 1 Vpp, RL = 100 kΩ, BW = 22 kHz Min. Typ. 110 Max. Unit nV ----------Hz Symbol en THD+N 0.07 % 1. Guaranteed by design. 4/19 Doc ID 15768 Rev 2 TSV611, TSV611A, TSV612, TSV612A Table 4. Symbol DC performance TSV61x TSV61xA Vio Offset voltage Tmin