V358I

TSV321-TSV358-TSV324 General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers ■ ■ ■ Operating at VCC = 2.5V to 6V Rail-to-rail input & output TSV321RILT Output VDD Non Inverting Input 1 2 3 4 Inverting Input 5 VCC Extended Vicm (VDD - 0.2V to V CC + 0.2V) ■ Capable of driving a 32Ω load resistor ■ ■ ■ High stability: 500pF Available in SOT23-5 micropackage Operating temperature range: -40, +125°C TSV321ID-TSV321IDT N.C. Inverting Input 1 2 3 4 _ + 8 7 6 5 N.C. VCC Output N.C. Description The TSV358 and TSV324 (dual & quad) are low voltage versions of LM358 and LM324 commodity operational amplifiers. TSV321 is the single version. The TSV321/358/324 are able to operate with voltage as low as 2.5V and features both I/O rail-to-rail. The common mode input voltage extends 200mV at 25°C beyond the supply voltages while the output voltage swing is within 100mV of each rail with 600 Ohm load resistor. These devices offer 1.3MHz of gain-bandwidth product and provide high output drive capability typically at 65mAload. These performances make the TSV3xx family ideal for active filters, general purpose low-voltage applications, general purpose portable devices. Non Inverting Input VDD TSV358IST-TSV358ID-TSV358IDT-TSV358IPT Output 1 Inverting Input 1 Non Inverting Input 1 VDD 1 2 3 4 _ + _ + 8 7 6 5 VCC Output 2 Inverting Input 2 Non Inverting Input 2 TSV324ID-TSV324IDT-TSV324IPT Output 1 Inverting Input 1 1 2 3 4 5 6 7 + _ + _ _ + _ + 14 Output 4 13 Inverting Input 4 12 Non Inverting Input 4 11 VDD 10 Non Inverting Input 3 9 8 Inverting Input 3 Output 3 Applications ■ ■ ■ ■ Non Inverting Input 1 VCC Battery-powered applications Audio driver (headphone driver) Sensor signal conditioning Laptop/notebook computers Non Inverting Input 2 Inverting Input 2 Output 2 December 2005 Rev. 3 1/15 www.st.com 15 Order Codes TSV321-TSV358-TSV324 1 Order Codes Part Number Temperature Range Package SOT23-5L SOT23-5L SO-8 Packaging Tape & Reel Tape & Reel Tube or Tape & Reel V358ID TSSOP8 (Thin Shrink Outline Package) -40°C to +125°C MiniSO-8 SO-8 (automotive grade level) TSSOP8 (automotive grade level) SO-14 TSSOP14 (Thin Shrink Outline Package) Tube or Tape & Reel Tape & Reel Tube or Tape & Reel Tape & Reel V358Y V324ID V324IP V358I Tape & Reel K175 Marking K174 K178 V321ID TSV321RILT TSV321RAILT TSV321ID/IDT TSV358ID/IDT TSV358IPT TSV358IST TSV358IYD/IYDT TSV358IYPT TSV324ID/IDT TSV324IPT 2/15 TSV321-TSV358-TSV324 Absolute Maximum Ratings 2 Table 1. Symbol VCC Vid Vi Tstg Tj Absolute Maximum Ratings Key parameters and their absolute maximum ratings Parameter Supply Voltage (1) Differential Input Voltage (2) Input Voltage Storage Temperature Maximum Junction Temperature Thermal Resistance Junction to Ambient(3) SOT23-5 SO-8 SO-14 TSSOP8 TSSOP14 MiniSO-8 HBM: Human Body Model(4) ESD MM: Machine Model(5) CDM: Charged Device Model Latch-up Immunity Lead Temperature (soldering, 10s) Output Short Circuit Duration 250 125 103 120 100 190 2 200 1.5 200 250 see note(6) Value 7 ±1 VDD -0.3 to VCC +0.3 -65 to +150 150 Unit V V V °C °C °C/W Rthja kV V kV mA °C 1. All voltages values, except differential voltage are with respect to network terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. If Vid > ±1V, the maximum input current must not exceed ±1mA. In this case (Vid > ±1V) an input series resistor must be added to limit input current. 3. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuit on all amplifiers. 4. Human body model, 100pF discharged through a 1.5kΩ resistor into pin of device. 5. Machine model ESD, a 200pF cap is charged to the specified voltage, then discharged directly into the IC with no external series resistor (internal resistor < 5Ω), into pin to pin of device. 6. Short-circuits from the output to VCC can cause excessive heating. The maximum output current is approximately 80mA, independent of the magnitude of VCC . Destructive dissipation can result from simultaneous short-circuits on all amplifiers. Table 2. Symbol VCC Vicm Vicm Toper Operating conditions Parameter Supply Voltage Common Mode Input Voltage Range (1) Common Mode Input Voltage Range (2) Value 2.5 to 6 VDD - 0.2 to VCC + 0.2 VDD to VCC -40 to + 125 Unit V V V °C Operating Free Air Temperature Range 1. At 25°C, for 2.5 ≤ VCC ≤ 6V, Vicm is extended to VDD - 0.2V, VCC + 0.2V. 2. In full temperature range, both Rails can be reached when VCC does not exceed 5.5V. 3/15 Electrical Characteristics TSV321-TSV358-TSV324 3 Table 3. Symbol Electrical Characteristics VCC = +3V, VDD = 0V, RL, CL connected to VCC/2, Tamb = 25°C (unless otherwise specified) Parameter Conditions Vicm = Vout = VCC /2 TSV321/358/324 TSV321A/358A/324A Min. Typ. Max. Unit Vio ∆Vio Iio Iib CMR SVR Avd Input Offset Voltage Input Offset Voltage Drift Input Offset Current Input Bias Current 1) (1) 0.2 0.1 2 3 1 mV µV/°C Vicm = Vout = V CC /2 Vicm = Vout = V CC /2 60 70 Vout = 0.5V to 2.5V RL = 2kΩ RL = 600Ω Vid = 100mV RL = 2kΩ RL = 600Ω Vid = -100mV RL = 2kΩ RL = 600Ω VID = 100mV, V O = VDD VID = -100mV, VO = VCC AVCL = 1, no load RL = 10kΩ, CL = 100pF, f = 100kHz RL = 10kΩ, CL = 100pF, AV = 1 CL = 100pF 1 0.42 20 20 80 74 2.82 2.80 3 4 80 85 92 95 2.95 2.95 88 115 80 30 125 nA nA dB dB dB Common Mode Rejection Ratio 0 ≤ Vicm ≤ VCC, Vout = VCC /2 Supply Voltage Rejection Ratio Large Signal Voltage Gain VOH High Level Output Voltage V VOL Low Level Output Voltage Output Source Current 120 160 mV Io ICC GBP SR φm en THD mA 80 420 1.3 0.6 53 27 0.01 650 µA MHz V/µs Degrees nV/√Hz % Output Sink Current Supply Current (per amplifier) Gain Bandwidth Product Slew Rate Phase Margin Input Voltage Noise Total Harmonic Distortion 1. Maximum values including unavoidable inaccuracies of the industrial test. 4/15 TSV321-TSV358-TSV324 Table 4. Symbol Electrical Characteristics VCC = +5V, VDD = 0V, RL, CL connected to VCC/2, Tamb = 25°C (unless otherwise specified) Parameter Conditions Vicm = Vout = VCC /2 TSV321/358/324 TSV321A/358A/324A Min. Typ. Max. Unit Vio ∆Vio Iio Iib CMR SVR Avd Input Offset Voltage Input Offset Voltage Drift Input Offset Current Input Bias Current 1) (1) 0.2 0.1 2 3 1 mV µV/°C Vicm = Vout = V CC /2 Vicm = Vout = V CC /2 65 70 Vout = 0.5V to 2.5V RL = 2kΩ RL = 600Ω Vid = 100mV RL = 2kΩ RL = 600Ω Vid = -100mV RL = 2kΩ RL = 600Ω VID = 100mV, V O = VDD VID = -100mV, VO = VCC AVCL = 1, no load RL = 10kΩ, CL = 100pF, f = 100kHz RL = 10kΩ, CL = 100pF, AV = 1 CL = 100pF 1 0.42 20 20 83 77 4.80 4.75 3 70 85 90 92 85 4.95 4.90 88 115 80 30 130 nA nA dB dB dB Common Mode Rejection Ratio 0 ≤ Vicm ≤ VCC, Vout = VCC /2 Supply Voltage Rejection Ratio Large Signal Voltage Gain VOH High Level Output Voltage V VOL Low Level Output Voltage Output Source Current 130 188 mV Io ICC GBP SR φm en THD mA 80 500 1.4 0.6 55 27 0.01 835 µA MHz V/µs Degrees nV/√Hz % Output Sink Current Supply Current (per amplifier) Gain Bandwidth Product Slew Rate Phase Margin Input Voltage Noise Total Harmonic Distortion 1. Maximum values including unavoidable inaccuracies of the industrial test. 5/15 Electrical Characteristics Figure 1. Supply current/amplifier vs. supply Figure 2. voltage 550 TSV321-TSV358-TSV324 Supply current/amplifier vs. temperature 600 500 Supply Current (µA) Vcc = 5V Supply Current (µA) 500 Vcc = 3V 450 400 350 300 250 -40 400 300 200 100 0 0 2 4 Supply Voltage (V) 6 8 Tamb = 25°C -20 0 20 40 60 80 100 120 140 Temperature (°C) Figure 3. Output power vs. supply voltage Figure 4. Input offset voltage drift vs. temperature 60 RL = 32 ohms 50 Output Power (mW) 1% distortion 40 30 0.1% distortion 20 10 10% distortion Input Voltage Drift (µV) 200 150 100 50 0 -50 -100 Vcc = 5V Vcc = 3V 0 1 2 3 4 5 6 Supply Voltage (V) -150 -40 -20 0 20 40 60 80 100 120 140 Temperature (°C) Figure 5. 10.0 Input bias current vs. temperature Vcc = 3V Vicm = 1.5V Figure 6. 110 Open loop gain vs. temperature RL = 2 kOhms Input bias current (nA) 0.0 Vcc = 5V Vicm = 2.5V Open Loop Gain (dB) 100 -10.0 90 RL = 600 ohms -20.0 -30.0 80 -40.0 -40 -20 0 20 40 60 80 100 Temperature (°C) 120 140 70 -40 -20 0 20 40 60 80 100 120 140 Temperature (°C) 6/15 TSV321-TSV358-TSV324 Figure 7. Open loop gain vs. temperature Figure 8. Electrical Characteristics High level output voltage vs. temperature 110 Voltage Referenced to VCC (mV) 110 Vcc = 3V Vicm = 1.5V Open Loop Gain (dB) 100 RL = 600 ohms 100 90 80 70 60 50 40 -40 Vcc = 5V RL = 2 kOhms Vcc = 3V 90 RL = 600 Ohms 80 70 -40 -20 0 20 40 60 80 100 120 140 -20 0 20 40 60 80 100 120 140 Temperature (°C) Temperature (°C) Figure 9. Low level output voltage vs. temperature Figure 10. Output current vs. temperature 110 Voltage Referenced to Gnd (mV) RL = 600 ohms 100 90 80 Vcc = 3V 70 60 50 40 -40 Vcc = 5V 100 Isink Output Current (mA) 50 Vcc = 5V Vid = 1V 0 -50 Isource -100 -20 0 20 40 60 80 100 120 140 -40 -20 0 20 40 60 80 100 120 140 Temperature (°C) Temperature (°C) Figure 11. Output current vs. temperature 100 Isink Figure 12. Output current vs. temperature 100 T = -40 °C sink T = 125 °C Vcc = 5V Vid = 0.1V Vicm = 2.5V T = 125 °C -50 T = 25 °C T = -40 °C source 2.0 3.0 Output Voltage (V) 4.0 5.0 T = 25 °C Output Current (mA) 60 80 100 120 140 Output Current (mA) 50 Vcc = 3V Vid = 1V 0 Isource -50 50 0 -100 -40 -20 0 20 40 Temperature (°C) -100 0.0 1.0 7/15 Electrical Characteristics Figure 13. Output current vs. temperature 100 T = -40 °C T = 25 °C Output Current (mA) 50 T = 125 °C Vcc = 3V Vid = 0.1V Vicm = 1.5V T = 125 °C -50 T = 25 °C T = -40 °C -100 0.0 0.5 1.0 1.5 2.0 2.5 source 3.0 3.5 sink TSV321-TSV358-TSV324 Figure 14. Gain & phase vs. frequency 70 60 50 Gain (dB) 40 gain 30 20 10 0 1E+3 phase 100 80 60 40 1E+4 1E+5 1E+6 Frequency (Hz) RL = 10K CL = 100 pF Vcc = 5V 180 160 140 Phase (°) Phase (°) 120 0 Output Voltage (V) Figure 15. Gain & phase vs. frequency 70 60 50 Gain (dB) 40 gain 30 20 10 0 1E+3 phase 100 80 60 40 1E+4 1E+5 Frequency (Hz) 1E+6 RL = 10K CL = 100 pF Vcc = 3V 180 160 140 Phase (°) 120 Figure 16. Slew rate vs. temperature 0.75 0.70 Slew Rate (V/µs) 0.65 0.60 0.55 0.50 0.45 0.40 0.35 -40 Vcc = 5V gain = +1 Vin = 2 to 3V RL = 10kohms CL = 100 pF positive Slew Rate negative Slew Rate -20 0 20 40 60 80 100 120 140 Temperature (°C) Figure 17. Slew rate vs. temperature 0.70 0.65 Slew Rate (V/µs) 0.60 0.55 0.50 0.45 0.40 0.35 -40 Vcc = 3V gain = +1 Vin = 1 to 2V RL = 10kohm CL = 100 pF positive Slew Rate Figure 18. Distortion vs. frequency 0.150 0.125 0.100 0.075 0.050 0.025 0.000 1E+1 Vcc = 3V Vout = 1Vpp RL = 32 ohms gain = -1 negative Slew Rate Distortion (%) -20 0 20 40 60 80 100 120 140 1E+2 1E+3 Frequency (Hz) 1E+4 1E+5 Temperature (°C) 8/15 TSV321-TSV358-TSV324 Package Mechanical Data 4 Package Mechanical Data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 4.1 SO-8 Package SO-8 MECHANICAL DATA DIM. A A1 A2 B C D E e H h L k ddd 0.1 5.80 0.25 0.40 mm. MIN. 1.35 0.10 1.10 0.33 0.19 4.80 3.80 1.27 6.20 0.50 1.27 8˚ (max.) 0.04 0.228 0.010 0.016 TYP MAX. 1.75 0.25 1.65 0.51 0.25 5.00 4.00 MIN. 0.053 0.04 0.043 0.013 0.007 0.189 0.150 0.050 0.244 0.020 0.050 inch TYP. MAX. 0.069 0.010 0.065 0.020 0.010 0.197 0.157 0016023/C 9/15 Package Mechanical Data TSV321-TSV358-TSV324 4.2 TSSOP8 Package TSSOP8 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L L1 0˚ 0.45 0.60 1 0.05 0.80 0.19 0.09 2.90 6.20 4.30 3.00 6.40 4.40 0.65 8˚ 0.75 0˚ 0.018 0.024 0.039 1.00 TYP MAX. 1.2 0.15 1.05 0.30 0.20 3.10 6.60 4.50 0.002 0.031 0.007 0.004 0.114 0.244 0.169 0.118 0.252 0.173 0.0256 8˚ 0.030 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.008 0.122 0.260 0.177 inch 0079397/D 10/15 TSV321-TSV358-TSV324 Package Mechanical Data 4.3 MiniSO-8 Package 11/15 Package Mechanical Data TSV321-TSV358-TSV324 4.4 SO-14 Package SO-14 MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 8.55 5.8 1.27 7.62 4.0 5.3 1.27 0.68 8 ˚ (max.) 0.149 0.181 0.019 8.75 6.2 0.35 0.19 0.5 45˚ (typ.) 0.336 0.228 0.050 0.300 0.157 0.208 0.050 0.026 0.344 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010 PO13G 12/15 TSV321-TSV358-TSV324 Package Mechanical Data 4.5 TSSOP14 Package TSSOP14 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0˚ 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8˚ 0.75 0˚ 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8˚ 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 13/15 Package Mechanical Data TSV321-TSV358-TSV324 4.6 SOT23-5 Package SOT23-5L MECHANICAL DATA mm. DIM. MIN. A A1 A2 b C D E E1 e e1 L 0.35 0.90 0.00 0.90 0.35 0.09 2.80 2.60 1.50 0 .95 1.9 0.55 13.7 TYP MAX. 1.45 0.15 1.30 0.50 0.20 3.00 3.00 1.75 MIN. 35.4 0.0 35.4 13.7 3.5 110.2 102.3 59.0 37.4 74.8 21.6 TYP. MAX. 57.1 5.9 51.2 19.7 7.8 118.1 118.1 68.8 mils 14/15 TSV321-TSV358-TSV324 Revision History 5 Revision History Table 5. Date Aug. 2005 Sept. 2005 Document revision history Revision 1 2 Changes – First Release - Products in full production – Addition of TS321A/TS324A/TS358A data in tables in Chapter 3: Electrical Characteristics on page 4. – Minor formatting and grammatical changes. – Missing PPAP references inserted see Table 1: Order Codes on page 2. Dec. 2005 3 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners © 7 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 15/15