VN340SPTR-E

VN340SP-33-E Quad high side smart Power solid state relay Features Type Vdemag(1) RDSon(1) 0.2Ω Iout(1) 1A VCC 36V PowerSO-10TM VN340SP-33-E VCC-55V 1. Per channel. ■ ■ ■ ■ ■ ■ ■ ■ ■ Output current : 1A per channel Digital I/O‘s clamped at 32V minimum voltage Shorted load and overtemperature protections Protection against loss of ground Built-in current limiter Undervoltage shut-down Open drain diagnostic output Fast demagnetization of inductive loads Conforms to IEC 61131-2 Description The VN340SP-33-E is a monolithic device made using STMicroelectronics VIPower technology, intended for driving four indipendent resistive or inductive loads with one side connected to ground. Active current limitation avoids dropping the system power supply in case of shorted load. Built-in thermal shut-down protects the chip from overtemperature and short circuit. The open drain diagnostic output indicates overtemperature conditions. Each I/O is pulled down when overtemperature condition of the relative channel is verified. Figure 1. Block diagram March 2007 Rev 3 1/16 www.st.com 16 Contents VN340SP-33-E Contents 1 2 3 4 5 6 7 8 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Switching time waveforms and truth table . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2/16 VN340SP-33-E Maximum ratings 1 Table 1. Symbol VCC -VCC IOUT IR IIN IDIAG VESD EAS Ptot TJ TSTG Maximum ratings Absolute maximum rating Parameter Power supply voltage Reverse supply voltage Output current (continuos) Reverse output current (per channel) Input current (per channel) Diag pin current Electrostatic discharge (R = 1.5KΩ; C = 100pF) Single pulse avalanche energy per channel not simultaneously Figure 4. Power dissipation at Tc = 25°C Junction operating temperature Storage temperature Value 45 -4 Internally limited -6 ± 10 ± 10 2000 400 Internally limited Internally limited -55 to 150 Unit V V A A mA mA V mJ w °C °C Table 2. Symbol RthJC RthJA Thermal data Parameter Thermal resistance junction-case (1) Thermal resistance junction-ambient (2) Max Max Max value 3 50 Unit °C/W °C/W 1. Per channel 2. When mounted using minimum recommended pad size on FR-4 board 3/16 Pin connections VN340SP-33-E 2 Figure 2. Pin connections Connection diagram (top view) Figure 3. VCC Current and voltage conventions IIN1 VIN1 10 VIN2 VIN3 VIN4 IIN2 IIN3 IIN4 IDIAG VDIAG 9 IN2 8 IN3 7 IN4 6 DIAG IN1 11 VCC 1 2 3 4 IOUT1 IOUT2 IOUT3 IOUT4 VOUT1 VOUT2 VOUT3 VOUT4 OUT1 OUT2 OUT3 OUT4 GND 5 4/16 VN340SP-33-E Electrical characteristics 3 Electrical characteristics 10V < VCC < 36V; -40°C < TJ < 125°C; unless otherwise specified Table 3. Symbol VCC RON Power section Parameter Supply voltage IOUT = 0.5A; TJ = 25°C On state resistance IOUT = 0.5A; TJ = 85°C IOUT = 0.5A; TJ = 125°C All channels OFF On state; VIN = 30V; IOUT = 0V (TJ = 125°C) VIN = VIL; RLOAD >= 10MΩ Test conditions Min 10 Typ Max 36 0.2 0.32 0.4 1 6 1.5 Unit V Ω Ω Ω mA mA V V mA IS VOL Vdemag ILGND Supply current Low state output voltage VCC-65 VCC-55 VCC-45 Output voltage at turn-off IOUT = 0.5A; LLOAD >= 1mH VCC = VINn = VGND = VSTAT = 18 to 30V Output current at turn-off 2 Tamb = - 25°C to 85°C Figure 6. Table 4. Symbol td(ON) tr td(OFF) tf Switching ( VCC = 24V) Parameter Turn-on delay time of Output current Rise time of output current Turn-off delay time of output current Fall time of output current Test conditions IOUT = 0.5A, resistive load input rise time < 0.1µs, TJ = 25°C IOUT = 0.5A, resistive load input rise time < 0.1µs, TJ = 25°C IOUT = 0.5A, resistive load input rise time < 0.1µs, TJ = 25°C IOUT = 0.5A, resistive load input rise time < 0.1µs, TJ = 25°C Min Typ 52 Max 100 Unit µs µs µs µs 94 250 34 50 8 20 Table 5. Symbol VIL VIH VI(HYST) IIN VICL Logical input Parameter I/O Input low level voltage I/O Input high level voltage (1) I/O Input hysteresis voltage I/O Input current I/O Input clamp voltage (1) VIN = 30V IIN = 1mA IIN = -1mA 32 36 -0.7 3.5 0.5 25 Test conditions Min Typ Max 2 Unit V V V µΑ V V 1. The input voltage is internally clamped at 32V minimum, it is possible to connect the input pins to an higher voltage via an external resistor calculate to not exceed 10mA 5/16 Electrical characteristics VN340SP-33-E Table 6. Symbol VDIAG(1) VSCL(1) VUSD ILIM IOVPK IDIAGH ILOAD tSC TTSD TR Protection and diagnostic Parameter Test conditions Min Typ Max 1 32 5 VCC = 24V; RLOAD < 10mΩ 1 36 -0.7 8 2 4 25 50 100 150 135 170 155 Unit V V V V A A µΑ µΑ µs °C °C Status voltage output low IDIAG = 5mA ( Fault condition ) Status clamp voltage Undervoltage shut down DC Short circuit current Leakage ondiag pin in high state Output leakage current Delay time of current limiter Thermal shut down temperature Thermal reset temperature Peak short circuit current VCC = 24V; VIN = 30; RLOAD < 10mΩ VDIAG = 24V VCC = 10 to 36V; VIN = VIL IDIAG = 1mA IDIAG = 1mA 1. Status determination > 100µs after the switching edge. Note: If INPUT pin is floating the corrisponding channel will automatically switch OFF. If GND pin is disconnected, the channel will switch OFF provided VCC not exceed 36V. 6/16 VN340SP-33-E Test circuits 4 Figure 4. Test circuits Avalance energy test circuit Figure 5. Peak short circuit test diagram 7/16 Test circuits VN340SP-33-E ILGND test configuration Figure 6. 8/16 VN340SP-33-E Switching time waveforms and truth table 5 Figure 7. Switching time waveforms and truth table Switching waveforms Figure 8. Switching parameter test conditions 9/16 Switching time waveforms and truth table VN340SP-33-E Table 7. Truth table MCOUTn I/On L H L L L H L H OUTPUTn L H L L L L L H Diagnostic H H H L H H H H Normal operation Overtemperature Undervoltage Shorted load ( Current limitation ) L H L H L H L H Figure 9. Driving circuit 10/16 VN340SP-33-E Package mechanical data 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 11/16 Package mechanical data VN340SP-33-E Table 8. Dim PowerSO-10 Mechanical data Mm Min Typ Max 3.65 0.10 0.60 0.32 9.60 7.60 9.50 7.40 7.60 6.35 6.10 1.27 1.25 13.80 0.50 1.20 1.70 0° 8° 1.80 0.047 0.067 1.35 14.40 0.049 0.543 0.002 0.071 Min 0.132 0.000 0.016 0.009 0.370 0.291 0.366 0.283 0.283 0.240 0.232 0.050 0.053 0.567 Inch Typ Max 0.144 0.004 0.024 0.012 0.378 0.300 0.374 0.291 0.300 0.250 0.240 A A1 B c D D1 E E1 E2 E3 E4 e F H h L q a 3.35 0.00 0.40 0.23 9.40 7.40 9.30 7.20 7.20 6.10 5.90 Figure 10. Package dimension 12/16 VN340SP-33-E Figure 11. PowerSO-10TM Suggested Pad and Tube Shipment (No Suffix) Package mechanical data Figure 12. Tape and Reel Shipment (Suffix “TR“) 13/16 Order codes VN340SP-33-E 7 Table 9. Order codes Order codes Part number VN340SP-E VN340SPTR-E Package PowerSO-10TM PowerSO-10TM Packaging Tube Tape and reel 14/16 VN340SP-33-E Revision history 8 Revision history Table 10. Date Revision history Revision 2 3 Final release Document reformatted, typo in Note 1 on page 6 Changes 5-Sep-2005 19-Mar-2007 15/16 VN340SP-33-E Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16