VN380SP13TR

VN380SP Smart solenoid driver solid state relay Features Type Vload(cl) In Ron VN380SP 60 V 5A 0.11  • Load current up to 7 A • CMOS compatible • Thermal shutdown • Diagnostic output • Integrated clamps • Over current protection • Open coil detection • Overvoltage detection Table 1. Description The VN380SP is monolithic device made using STMicroelectonics VIPower™ Technology, intended for driving inductive loads. The inputs are CMOS compatible. The diagnostic output provides an indication of open-load and demagnetization mode. Built-in thermal shutdown protects the chip from over temperature. In case or over current or over temperature or overvoltage the product will automatically operate in recirculation mode. Device summary Order codes Package PowerSO-1O September 2013 Tube Tube (lead free) Tape and reel Tape and reel (lead free) VN380SP VN380SP-E VN380SP13TR VN380SPTR-E Doc ID 15602 Rev 2 1/12 www.st.com 12 Contents VN380SP Contents 1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 4 2.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1 Current cut off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.2 Open-load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.3 Thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.4 Overvoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.1 5 2/12 PowerSO-10 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Doc ID 15602 Rev 2 VN380SP 1 Block diagram and pin description Block diagram and pin description Figure 1. Block diagram Vpwr2 Vpwr1 OVERVOLT. INTERNAL SUPPLY DRIVER S2 S2 INPUT A INPUT A OVER CLAMP CURRENT 2 LOGIC INPUT B LOAD OPEN LOAD INPUT B CLAMP 1 OVERTEMP DRIVER S1 STATUS S1 DIAG Figure 2. GND Configuration diagram (top view) 5 4 3 INPUT A INPUT B DIAG Vpwr1 6 7 N.C. 10 8 9 2 GND GND N.C. Vpwr2 1 Vpwr2 11 LOAD PowerSO-10TM Doc ID 15602 Rev 2 3/12 Electrical specifications 2 VN380SP Electrical specifications Figure 3. Current and voltage conventions Ipwr1 Vpwr1 IINA VINA Ipwr2 INPUT A Vpwr1 ILOAD Vpwr2 LOAD IDIAG IINB INPUT B VINB 2.1 Vpwr2 VLOAD DIAG GND VDIAG Absolute maximum ratings Table 2. Absolute maximum ratings Symbol Parameter Value Unit Vload Maximum DC load voltage Internally clamped V Iload Maximum DC load current Internally clamped A Irload Reverse load current, Tcase = 25 °C -10 A Ec Maximum clamping energy, Tcase = 150 °C, f = 40 Hz, 1000 hours (f: input A frequency) 100 mJ Ec Maximum clamping energy, Tcase = -40 °C, f = 75 Hz, 5 minutes (f: input A frequency) 100 mJ Iin Inputs current +/-10 mA Idiag Diagnostic output current +/-10 mA VESD Electrostatic discharge (R = 1.5 k, C = 100 pF, all pins) 2000 V Vpwr1 Power voltage 1 60 V Vpwr2 Power voltage 2 60 V RVpwr Reverse power voltage -0.3 V Tj Junction operating temperature Tstg Storage temperature Vin -40 to 150(1) -55 to 150 °C Input voltages 8 V Vdiag Diagnostic output voltage 8 V Cload Load capacity 1 µF 1. Higher temperature is allowed during a short time before thermal shutdown. Permanent operation above oC 150 is not allowed. 4/12 °C Doc ID 15602 Rev 2 VN380SP 2.2 Electrical specifications Thermal data Table 3. Thermal data Symbol Parameter Rthj-case Thermal resistance junction-case max Rthj-amb Thermal resistance junction-ambient max(1) PowerSO-10 Unit 1.67 °C/W 50 °C/W 1. When mounted using minimum recommented pad size on FR-4 board. 2.3 Electrical characteristics 10 V < VPWR1 < 18 V; -40 °C < TJ < 150 °C unless otherwise specified Table 4. Symbol Electrical characteristics Parameter Test conditions Min Typ Max Unit 6 13 24 V Power Vpwr1 Operating voltage Ron1 On-state resistance (excitation path) Iload = In = 5 A VinA = VinB = 5 V 0.2  Ron2 On-state resistance (recirculation path) Vpwr1 = 13 V; Iload = In = 5 A VinA = 5 V; VinB = GND 0.4  V Vce(sat) Iload = In = 5 A Vpwr1 = Vpwr2 = 13 V Iload = 10 A; TJ > 125 °C Vpwr1 = Vpwr2 = 13 V 2 Saturation voltage of bipolar S2 2 V Isq Supply quiescent current Vpwr1 = 13 V; VinA = VinB = 5 V 25 mA Ilk Output leakage current Vpwr1 = 18 V; VinA = VinB = GND 5 mA Off-state supply current VinA = VinB = GND Vpwr1 = not connected 10 V < Vpwr2 < 24 V TJ = 25 °C 50 µA 50 µs 20 µs 50 µs 20 µs 1.5 V Ioff Switching (excitation path) td(on) Turn-on delay time Rload = 2.5 ; VinA = 5 V (see Figure 4) tr Rise time of output current Rload = 2.5 ; VinA = 5 V (see Figure 4) td(off) Turn-off delay time Rload = 2.5 ; VinA = 5 V (see Figure 4) tf Fall time of output current Rload = 2.5 ; VinA = 5 V (see Figure 4) 1 1 Logic input Vil Input low level voltage Doc ID 15602 Rev 2 5/12 Electrical specifications Table 4. VN380SP Electrical characteristics (continued) Symbol Parameter Test conditions Min Typ Max Unit Vih Input high level voltage 3.5 Vi(hyst) Input hysteresis voltage 0.5 0.8 2 V Vi(CL) Input clamp voltage Iin = 10 mA 8 9.5 11 V Input current VinA = VinB = 2 V VinA = VinB = 5 V 20 250 µA µA 200 °C 30 A Iin V Protections and diagnostics Ttsd Thermal shutdown temperature 160 Ilim Current cut off level 15 Vov Overvoltage threshold VinA = VinB = 5 V Vdiag Status output voltage Diagnostic output active (low) Idiag = 2 mA Vdiag(CL) Status output clamp voltage Idiag = 10 mA Status propagation delay Demagnetization mode (fast turn-off) Vdiag = 1 V (seeFigure 6) Vcl1 Switch S1 detection clamp Iload = In = 5 A 60 Vcl2 Output inductive clamp voltage Iload = In = 5 A 24 Vfb Flyback diagnostic threshold Demagnetization mode (fast turn-off) Vcl = Vcl1 or Vcl2 Iol Open-load current level Td Table 5. 180 27 V 0.5 V 11 V 70 µs 70 80 V 28.5 33 V Vcl-5 Vcl V 5 700 mA 8 9.5 Truth table Conditions In A In B S1 S2 Standby modes L L L H Off Off Off Off Excitation mode H H On Off Recirculation mode H L Off On Demagnetization mode (fast turn-off) Vpwr2 +Vcl2 Vcl1 L L L L Off On On On Thermal shutdown H H Off On Current cut off H H Off On Open-load Overvoltage 6/12 See open-load waveforms on Figure 5 H Doc ID 15602 Rev 2 H Off On VN380SP Functional description 3 Functional description 3.1 Current cut off When the load current rise above the current cut off level, S1 is automatically switched off and the devices operates in recirculation mode (S2 active). S1 is latched off until A goes low and high again. This default is not displayed by diagnostic flag. 3.2 Open-load If the load current is below the open-load current level, the flag of the open-load block is activated but this default is displayed by the diagnostic output on the falling edge of input B and the diagnostic output is latched at low level until input A goes low and high again. In case an open-load is detected during an active phase of input B, but disappears before a falling edge of input B, this default is not dispayed by the diagnostic flag (see open-load waveforms on Figure 5). 3.3 Thermal shutdown The device is internally protected against over temperatures by the thermal circuit protection. When the device junction temperature exceeds the protection limit, S1 is automatically switched off. Therefore the device operates in recirculation mode (S2 active). S1 remain latched off until Vpwr1 goes low and high again. This default is not dispayed by the diagnostic flag. 3.4 Overvoltage During the on-state of S1 switch, if Vpwr1 or Vpwr2 is rising above the threshold detection S1 is automatically switched off, therefore the device operates in recirculation mode. Figure 4. Switching parameter test conditions Doc ID 15602 Rev 2 7/12 Functional description Figure 5. VN380SP Switching waveforms OPEN LOAD NORMAL MODES INPUT A INPUT A INPUT B INPUT B IOL IOL ILOAD IOL ILOAD connected LOAD Vpwr2 +VCL2 < VCL1 disconnected DIAG Vpwr2 Vpwr2 +VCL2 < VCL1 VLOAD DIAG VLOAD ON S1 OFF S2 OFF S1 ON OFF S2 ON OFF ON THERMAL SHUTDOWN CURRENT CUT OFF INPUT A Vpwr1 INPUT B INPUT A ILIM INPUT B ILOAD VLOAD Tj DIAG VLOAD ON S1 OFF ON S2 TTSD OFF ON S1 OFF S2 ON OFF DIAG OVERVOLTAGE INPUT A INPUT B VOV Vpwr1 or Vpwr2 Iload VLOAD ON S1 OFF S2 OFF ON DIAG Figure 6. Demagnetization mode Fast turn off INPUT A INPUT B td 1V DIAG 8/12 Doc ID 15602 Rev 2 VN380SP 4 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 4.1 PowerSO-10 mechanical data Table 6. PowerSO-10 mechanical data mm inch Dim. Min. Typ. Max. Min. Typ. Max. A 3.35 3.65 0.132 0.144 A1 0.00 0.10 0.000 0.004 B 0.40 0.60 0.016 0.024 c 0.35 0.55 0.013 0.022 D 9.40 9.60 0.370 0.378 D1 7.40 7.60 0.291 0.300 E 9.30 9.50 0.366 0.374 E1 7.20 7.40 0.283 0.291 E2 7.20 7.60 0.283 0.300 E3 6.10 6.35 0.240 0.250 E4 5.90 6.10 0.232 0.240 e 1.27 0.050 F 1.25 1.35 0.049 0.053 H 13.80 14.40 0.543 0.567 h L 0.50 1.20 q  0.002 1.80 1.70 0° 0.047 0.071 0.067 8° Doc ID 15602 Rev 2 9/12 Package information Figure 7. 10/12 VN380SP PowerSO-10 package dimension Doc ID 15602 Rev 2 VN380SP 5 Revision history Revision history Table 7. Document revision history Date Revision Changes 10-Jun-2009 1 Initial release. 20-Sep-2013 2 Updated Disclaimer. Doc ID 15602 Rev 2 11/12 VN380SP Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 12/12 Doc ID 15602 Rev 2