VN460SP-E

VN460SP  SINGLE CHANNEL HIGH SIDE SMART SOLID STATE RELAY T YPE V de ma g R DS(o n) IO UT V CC VN460SP V CC -55V 20 m Ω 25 A 36 V ■ ■ ■ ■ ■ ■ ■ OUTPUT CURRENT (CONTINUOUS): 25 A @ TC = 25 o C 5 V LOGIC LEVEL COMPATIBLE INPUT UNDER VOLTAGE SHUT-DOWN OVER VOLTAGE SHUT-DOWN THERMAL SHUT-DOWN OPEN DRAIN DIAGNOSTIC OUTPUT VERY LOW STAND-BY POWER DISSIPATION u d o 1 r P e Power SO-10 TM DESCRIPTION The VN460SP is a monolithic device made using SGS-THOMSON Vertical Intelligent Power Technology, intended for driving resistive or inductive loads with one side connected to ground. Built-in thermal shut-down protects the chip from over temperature and short circuit. )- s ( t c u d o ) s ( ct 10 t e l o s b O The control input is 5V CMOS logic level compatible. The open drain diagnostic output indicates open circuit (no load) and overtemperature status. r P e BLOCK DIAGRAM t e l o s b O September 2013 DocID5691 Rev 3 1/9 VN460SP ABSOLUTE MAXIMUM RATING Symb ol Parameter VCC Power Supply Voltage (continuous) -V CC Reverse Supply Voltage (continuous) I OUT Output Current (continuous) Unit 45 V -0.3 V Internally Limited A IR Reverse Output Current -25 A I IN Input Current ±10 mA I STAT Status Pin Current ±10 mA -I GND Reverse Ground Current -200 mA V ESD Electrostatic Discharge (1.5 kΩ, 100 pF) 2000 V o P tot Power Dissipation at T c ≤ 25 C 112 Tj Junction Operating Temperature -40 to 150 Storage Temperature -55 to 150 T s tg r P e t e l o ) (s t c u d o r P e t e l o CURRENT AND VOLTAGE CONVENTIONS s b O ) s ( ct u d o CONNECTION DIAGRAM 2/9 Value s b O W o C o C VN460SP ELECTRICAL TRANSIENTS REQUIREMENTS ISO T/R 7637/1 Test Pu lse T EST LEVEL S I II III IV Delays an d Impedance 1 -25 V -50 V -75 V -100 V 2 ms, 10 Ω 2 +25 V +50 V +75 V +100 V 0.2 ms, 10 Ω 3a -25 V -50 V -100 V -150 V 0.1 µs, 50 Ω +50 V +75 V +100 V 0.1 µs, 50 Ω 3b +25 V 4 -4 V -5 V -6 V -7 V 100 ms, 0.01 Ω 5 +26.5 +46.5 +66.5 +86.5 400 ms, 2 Ω ISO T/R 7637/1 Test Pu lse TEST L EVELS RESUL TS I II III 1 C C C 2 C C C 3a C C 3b C C 4 C C 5 C (s) E (With a series resistor ≥ 1 KΩ in input and status pins). od CL ASS r P e C t e l o E t c u C -O u d o r P e IV let o s b ) s ( ct C C C C C C C E E CONT ENT S All function of the device are performed as designed after exposure to disturbance. One or more functions of the device is not performed as designed after exposure and cannot be returned to proper operation without replacing the device. s b O 3/9 VN460SP THERMAL DATA R t hj-ca se R thj-a (∗) Thermal Resistance Junction-case Max Thermal Resistance Junction-ambient Max 1.1 o C/W 50 o C/W (∗) When mounted using minimum recommended pad size on FR-4 board. ELECTRICAL CHARACTERISTICS (VCC = 13 V; -40 oC < TJ < 125 oC unless otherwise specified) POWER Symb ol Parameter VCC Operating Supply Voltage V usd Under Voltage Shut Down V ov Overvoltage Shut Down R on IS Test Cond ition s On State Resistance I OUT = 5 A I OUT = 5 A T J = 25 C Supply Current Off state On State TCase = 25 C t e l o Input Low Level Voltage (*) VI H Input High Level Voltage (see note 1) (*) V I(hyst.) Input Hysteresis Voltage V ICL Pr Input Clamp Voltage e t e ol O ) s ( t c u d o Input Current I IN bs Test Cond ition s VI L Max. Un it 13 36 V 3 4 36 39 Min. V 45 V 20 36 mΩ mΩ 15 1.4 30 3.3 µA mA Typ . Max. Un it 1.5 V 3.5 0.2 V 0.85 Tc ase = 25 oC VI N = 5 V I IN = 10 mA I IN = -10 mA ) s ( ct 5.5 u d o r P e o Parameter Typ . 5.5 o LOGIC INPUT Symb ol Min. 5 6 -0.7 1.5 V 100 µA 7 V V (*) : The input voltage is internally clamped at 6 V about. It is possible to connect this pin to an higher voltage via an external resistor provided the input current does not exceed 10 mA. SWITCHING (VCC = 13 V) s b O Symb ol Parameter Test Cond ition s Min. Typ . Max. Un it t d(on) Turn-on Delay Time Of Output Current I OUT = 5 A Resistive Load Input Rise T ime < 0.1 µs T j = 25 o C 25 90 250 µs Rise Time O f O utput Current I OUT = 5 A Resistive Load Input Rise T ime < 0.1 µs T j = 25 o C 80 300 650 µs Turn-off Delay Time O f I OUT = 5 A Resistive Load Output Current Input Rise T ime < 0.1 µs T j = 25 o C 300 750 1500 µs Fall T ime Of Output Current I OUT = 5 A Resistive Load o Input Rise T ime < 0.1 µs T j = 25 C 80 200 400 µs (di/dt) on Turn-on Current Slope I OUT = 5 A 0.02 0.05 A/µs (di/dt) off Turn-off Current Slope I OUT = 5 A 0.02 0.05 A/µs tr t d(of f) tf 4/9 VN460SP ELECTRICAL CHARACTERISTICS (continued) PROTECTIONS AND DIAGNOSTICS Symb ol Min. Typ . Max. T TSD Thermal Shut-down Temperature Parameter Test Cond ition s 150 170 190 T TR Thermal Reset Temperature 135 T RSD Thermal Hysteresis 5 15 50 Un it o C o C o C (HYST) Output Voltage Authorizing Openload Detection 8V≤VCC ≤30V 5.2 6.6 8 I OL Open Load Current Level 8V≤VCC ≤30V 100 800 1500 I OV Over Current R LOAD ≤10 mΩ o o - 40 C