VND600PEP13TR

® VND600PEP DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY TARGET SPECIFICATION TYPE VND600PEP s s s RDS(on) 30mΩ Ilim 25A VCC 36V DC SHORT CIRCUIT CURRENT: 25A CMOS COMPATIBLE INPUTS PROPORTIONAL LOAD CURRENT SENSE s UNDERVOLTAGE AND OVERVOLTAGE SHUT-DOWN s OVERVOLTAGE CLAMP s THERMAL SHUT-DOWN s CURRENT LIMITATION s VERY LOW STAND-BY POWER DISSIPATION s PROTECTION AGAINST: nLOSS OF GROUND AND LOSS OF VCC s REVERSE BATTERY PROTECTION (*) DESCRIPTION The VND600PEP is a monolithic device made using STMicroelectronics VIPower M0-3 technology. It is intended for driving resistive or inductive loads with one side connected to ground. Active VCC pin voltage clamp protects the BLOCK DIAGRAM PowerSSO-24 ORDER CODES PACKAGE TUBE PowerSSO-24 VND600PEP T&R VND600PEP13TR device against low energy spikes (see ISO7637 transient compatibility table). This device has two channels in high side configuration; each channel has an analog sense output on which the sensing current is proportional (according to a known ratio) to the corresponding load current. Built-in thermal shut-down and outputs current limitation protect the chip from over temperature and short circuit. Device turns off in case of ground pin disconnection. VCC OVERVOLTAGE VCC C LAMP UNDERVOLTAGE PwCLAMP 1 DRIVER 1 INPUT 1 LOGIC INPUT 2 GND DRIVER 2 ILIM1 Vdslim1 IOUT1 K Ot1 OUTPUT 1 CURRENT SENSE 1 OUTPUT 2 Ot2 PwCLAMP 2 Ot1 ILIM2 Vdslim2 IOUT2 OVERTEMP. 1 OVERTEMP. 2 Ot2 K CURRENT SENSE 2 (*) See application schematic at page 8 October 2003 - Revision 1.4 (Working document) 1/11 This is preliminary information on a new product foreseen to be developed. Details are subject to change without notice. VND600PEP ABSOLUTE MAXIMUM RATING Symbol VCC -VCC - IGND IOUT IR IIN VCSENSE Parameter DC supply voltage Reverse supply voltage DC reverse ground pin current Output current Reverse output current Input current Current sense maximum voltage Electrostatic Discharge (Human Body Model: R=1.5KΩ; C=100pF) - INPUT VESD - CURRENT SENSE - OUTPUT Ptot Tj Tc TSTG - VCC Power dissipation at Tc=25°C Junction operating temperature Case operating temperature Storage temperature 4000 2000 5000 5000 96 Internally limited -40 to 150 -55 to 150 V V V V W °C °C °C Value 41 -0.3 -200 Internally limited -21 +/- 10 -3 +15 Unit V V mA A A mA V V CONNECTION DIAGRAM (TOP VIEW) VCC GND NC INPUT2 NC INPUT1 NC C.SENSE1 NC C.SENSE2 NC VCC 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 OUTPUT2 OUTPUT2 OUTPUT2 OUTPUT2 OUTPUT2 OUTPUT2 OUTPUT1 OUTPUT1 OUTPUT1 OUTPUT1 OUTPUT1 OUTPUT1 TAB = VCC CURRENT AND VOLTAGE CONVENTIONS IS VCC IIN1 INPUT1 VIN1 IIN2 VIN2 INPUT2 IOUT1 OUTPUT1 ISENSE1 IOUT2 OUTPUT2 VSENSE1 VOUT1 VCC CURRENT SENSE 1 V ISENSE2 OUT2 VSENSE2 CURRENT SENSE 2 GROUND IGND 2/11 VND600PEP THERMAL DATA Symbol Rthj-case (1) Rthj-case (2) Rthj-amb Parameter Thermal resistance junction-case Thermal resistance junction-case Thermal resistance junction-ambient (MAX) (MAX) (MAX) Value 1.8 1.3 60 (*) Unit °C/W °C/W °C/W (*) When mounted on a standard single-sided FR-4 board with 1cm2 of Cu (at least 35µm thick). Note: (1) one channel ON - (2) two channels ON ELECTRICAL CHARACTERISTICS (8V