Z00607MA2BL2

Z00607 Standard 0.8 A Triacs Datasheet - production data Description A2 The Z00607 is suitable for low power AC switching applications. Typical applications include home appliances (electrovalve, pump, door lock, small lamp control), fan speed controllers,... G A1 A2 G A2 A2 A1 TO-92 Z00607MA Thanks to the low gate triggering current these triacs can be driven directly by microcontrollers. A1 G SOT-223 Z00607MN Features • On-state rms current = 0.8 A • Repetitive peak off-state voltage = 600 V • Gate triggering current = 5 mA June 2014 This is information on a product in full production. DocID6629 Rev 9 1/8 www.st.com Characteristics 1 Z00607 Characteristics Table 1. Absolute maximum ratings Symbol IT(RMS) ITSM I²t Parameter On-state rms current (full sine wave) SOT-223 Ttab = 85 °C TO-92 TL = 50 °C Non repetitive surge peak on-state current (full cycle, Tj initial = 25 °C) F = 50 Hz t = 20 ms F = 60 Hz t = 16.7 ms I²t Value for fusing tp = 10 ms Value Unit 0.8 A 9 A 9.5 0.45 A ²s dI/dt Critical rate of rise of on-state current IG F = 120 Hz = 2 x IGT , tr ≤ 100 ns Tj = 110 °C 20 A/µs IGM Peak gate current Tj = 110 °C 1 A Tj = 110 °C 0.1 W - 40 to + 150 - 40 to + 110 °C PG(AV) Tstg Tj tp = 20 µs Average gate power dissipation Storage junction temperature range Operating junction temperature range Table 2. Electrical characteristics (Tj = 25 °C, unless otherwise specified) Symbol IGT (1) Test Conditions Quadrant I - II - III VD = 12 V, RL = 30 Ω IH (2) IV VD = VDRM, RL = 3.3 kΩ, Τj = 110 °Χ ALL MAX 1.3 V ALL MIN 0.2 V MX. 5 mA IT = 200 mA dV/dt (2) (dV/dt)c (2) IG = 1.2 IGT mA 7 I - III - IV IL Unit 5 MAX VGT VGD Value 10 MAX II mA 20 VD = 67% VDRM, gate open Τj = 110 °Χ MIN 10 V/µs (δς/δτ)χ = 0.35 Α/μσ, Τj = 110 °Χ MIN 1.5 V/µs 1. minimum IGT is guaranteed at 5% of IGT max. 2. for both polarities of A2 referenced to A1. Table 3. Static characteristics Symbol VTM(1) Vto (1) Rd (1) IDRM IRRM Test Conditions ITM = 1.1 A tp = 380 µs Unit Tj = 25 °C MAX. 1.5 V Threshold voltage Tj = 110 °C MAX. 0.95 V Dynamic resistance Tj = 110 °C MAX. 420 mΩ 5 µA 0.1 mA VDRM = VRRM = 600 V Tj = 25 °C Tj = 110 °C 1. for both polarities of A2 referenced to A1. 2/8 Value DocID6629 Rev 9 MAX. Z00607 Characteristics Table 4. Thermal resistances Symbol Parameter Value Rth(j-t) Junction to tab (AC) SOT-223 25 Rth(j-I) Junction to lead (AC) TO-92 60 SOT-223 60 Rth(j-a) Junction to ambient TO-92 150 Unit °C/W S(1) = 5 cm² °C/W 1. S = Copper surface under tab. Figure 1. Maximum power dissipation versus RMS on-state current (full cycle) Figure 2. Relative variation of gate trigger, holding and latching current versus junction temperature IGT, IH, IL [Tj] / IGT, IH, IL [Tj=25°C] P(W) 2.5 1.0 Typical values 0.9 2.0 0.8 0.7 IGT 1.5 0.6 0.5 IH & IL 1.0 0.4 0.3 0.2 0.5 0.1 Tj (°C) IT(RMS)(A) 0.0 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Figure 3. Surge peak on-state current versus number of cycles -40 -20 0 20 40 60 80 100 120 Figure 4. Non-repetitive surge peak on-state current and corresponding value of I2t ITSM (A), I2t (A2s) ITSM (A) 200.0 10 100.0 9 Tj initial = 25°C t=20ms 8 dI/dt limitation: 20A/µs One cycle 7 ITSM Non repetitive Tj initial = 25°C 6 10.0 5 4 Repetitive Tamb = 25°C 3 1.0 I2t 2 1 Number of cycles 0 1 10 100 Sinusoidal pulse with width tp < 10 ms 0.1 1000 0.01 DocID6629 Rev 9 0.10 1.00 tp (ms) 10.00 3/8 8 Characteristics Z00607 Figure 5. On-state characteristics (maximum values) Figure 6. Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values) ITM(A) (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c 10.0 10.0 8.0 6.0 Tj = Tjmax. 1.0 4.0 Tj=max. Vt0=0.95 V Rd=420 mΩ Tj = 25°C 2.0 VTM (V) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 4 3 2 1 Tj (°C) 4/8 20 30 40 50 60 10.0 Figure 8. SOT-223 Thermal resistance junction to ambient versus copper surface under tab 130 120 110 100 90 80 70 60 50 40 30 20 10 0 5 10 1.0 Rth(j-a)(°C/W) (dI/dt)c [Tj] / (dI/dt)c [Tj Specified] 6 0 0.1 5.0 Figure 7. Relative variation of critical rate of decrease of main current versus junction temperature 0 (dV/dt)c (V/µs) 0.0 0.1 70 80 90 100 110 Printed circuit board FR4, copper thickness = 35 µm S(cm²) 0.0 DocID6629 Rev 9 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Z00607 2 Ordering information scheme Ordering information scheme Figure 9. Ordering information scheme Z 006 07 M A Blank 1BA2 Triac series Current 006 = 0.8A Sensitivity 07 = 5mA Voltage M = 600V Package A = TO-92 N = SOT-223 Packing mode 1BA2 = TO-92 Bulk 2BL2 = TO-92 Ammopack 5BL2 = TO-92 Tape and reel 5AA4 = SOT-223 Tape and reel DocID6629 Rev 9 5/8 8 Packaging information 3 Z00607 Packaging information • Epoxy meets UL94, V0 • Lead-free package In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 5. SOT-223 dimensions Dimensions Ref. V A A1 Millimeters Min. c Typ. A B A1 e1 Inches Max. Min. Typ. Max. 1.80 0.071 0.02 0.10 0.001 0.004 B 0.60 0.70 0.85 0.024 0.027 0.033 B1 2.90 3.00 3.15 0.114 0.118 0.124 c 0.24 0.26 0.35 0.009 0.010 0.014 D(1) 6.30 6.50 6.70 0.248 0.256 0.264 D B1 4 H E 1 2 3 e e 2.3 0.090 e1 4.6 0.181 E(1) 3.30 3.50 3.70 0.130 0.138 0.146 H 6.70 7.00 7.30 0.264 0.276 0.287 V 10° max 1. Do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15mm (0.006inches) Figure 10. Footprint (dimensions in mm) 3.25 1.32 5.16 7.80 1.32 2.30 6/8 DocID6629 Rev 9 0.95 Z00607 Ordering information Table 6. TO-92 dimensions DIMENSIONS Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A a B A 1.35 B C 4.70 C F 4 D E 0.053 0.185 2.54 0.100 D 4.40 0.173 E 12.70 0.500 F 3.70 0.146 a 0.50 0.019 Ordering information Table 7. Ordering information 5 Ordering type Marking Z00607MA 1BA2 Z0607MA Z00607MA 2BL2 Z0607MA Z00607MA 5BL2 Z0607MA Z00607MN 5AA4 Z06M Package TO-92 SOT-223 Weight 0.2 g 0.12 g Base quantity Delivery mode 2500 Bulk 2000 Ammopack 2000 Tape and reel 1000 Tape and reel Revision history Table 8. Document revision history Date Revision Changes Oct-2001 4 Last update. 25-Mar-2005 5 Package: TO-92 tape and reel delivery mode 5BL2 added. 21-Jun-2005 6 Markings updated from Z006xxxx to Z06xxxx 13-Sep-2005 7 Z00607MA 2BL2: marking corrected from 00607mA to Z0607MA 12-Apr-2007 8 Reformatted to current standard. Added SOT-223 package. Changed Tj from +125 to +110 in Table 1 19-Jun-2014 9 Updated marking for Z00607MN 5AA4 in Table 7. DocID6629 Rev 9 7/8 8 Z00607 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2014 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 8/8 DocID6629 Rev 9