SDC1205-100MF

SMD POWER INDUCTORS 1. PART NO. EXPRESSION : SDC1205 SERIES SDC1205-1R3YF (a) (b) (c) (d)(e) (a) Series code (b) Dimension code (c) Inductance code : 1R3 = 1.3uH (d) Tolerance code : M = ±20%, Y = ±30% (e) F : Lead Free 2. CONFIGURATION & DIMENSIONS : Clip Termination A C D L G 220 B E PCB Pattern Unit:m/m A 12.0±0.3 B 12.0±0.3 C 6.0 Max. D 5.0±0.2 E 7.6±0.2 G 7.0 Ref. H 5.4 Ref. L 12.6 Ref. 3. SCHEMATIC : 4. GENERAL SPECIFICATION : a) Temp. rise : 40°C Max. b) Ambient temp. : 25°C c) Rated current : Base on temp. rise & L/L0A = 30% Max. d) Operating temp. : -25°C to +85°C e) Storage temp. : -25°C to +85°C NOTE : Specifications subject to change without notice. Please check our website for latest information. H 12.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 1 SMD POWER INDUCTORS 5. ELECTRICAL CHARACTERISTICS : Part No. SDC1205-1R3YF SDC1205-2R1YF SDC1205-3R1YF SDC1205-4R4YF SDC1205-5R8YF SDC1205-7R5YF SDC1205-100MF SDC1205-120MF SDC1205-150MF SDC1205-180MF SDC1205-220MF SDC1205-270MF SDC1205-330MF SDC1205-390MF SDC1205-470MF SDC1205-560MF SDC1205-680MF SDC1205-820MF SDC1205-101MF SDC1205-121MF SDC1205-151MF SDC1205-181MF SDC1205-221MF SDC1205-271MF SDC1205-331MF SDC1205-391MF SDC1205-471MF SDC1205-561MF SDC1205-681MF SDC1205-821MF SDC1205-102MF Inductance ( µH ) 1.3 ±30% 2.1 ±30% 3.1 ±30% 4.4 ±30% 5.8 ±30% 7.5 ±30% 10 ±20% 12 ±20% 15 ±20% 18 ±20% 22 ±20% 27 ±20% 33 ±20% 39 ±20% 47 ±20% 56 ±20% 68 ±20% 82 ±20% 100 ±20% 120 ±20% 150 ±20% 180 ±20% 220 ±20% 270 ±20% 330 ±20% 390 ±20% 470 ±20% 560 ±20% 680 ±20% 820 ±20% 1000 ±20% Test Frequency ( Hz ) 1V / 7.96M 1V / 7.96M 1V / 7.96M 1V / 7.96M 1V / 7.96M 1V / 7.96M 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K 1V / 1K SDC1205 SERIES DCR () Max. 0.012 0.014 0.017 0.020 0.021 0.024 0.025 0.027 0.030 0.034 0.036 0.051 0.057 0.068 0.075 0.110 0.120 0.140 0.160 0.170 0.230 0.290 0.400 0.460 0.510 0.690 0.770 0.860 1.200 1.340 1.530 IDC (A) Max. 8.00 7.00 6.00 5.00 4.40 4.20 4.00 3.50 3.30 3.00 2.80 2.30 2.10 2.00 1.80 1.70 1.50 1.40 1.30 1.10 1.00 0.90 0.80 0.75 0.68 0.65 0.58 0.54 0.48 0.43 0.40 NOTE : Specifications subject to change without notice. Please check our website for latest information. 12.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 2 SMD POWER INDUCTORS 6. RELIABILITY AND TEST CONDITIONS : SDC1205 SERIES ITEM Electrical Characteristics Test Inductance DCR Heat Rated Current (Irms) PERFORMANCE Refer to standard electrical characteristics list TEST CONDITION HP4284A, CH11025, CH3302, CH1320, CH1320S LCR meter. CH16502, Agilent33420A Micro-Ohm Meter. Irms(A) will cause the coil temperature rise approximately T=40°C without core loss 1. Applied the allowed DC current 2. Temperature measured by digital surface thermometer Isat(A) will cause Lo to drop approximately 20% max. Saturation Current (Isat) Mechanical Performance Test Solderability Test More than 90% of the terminal electrode should be covered with solder. Preheating Dipping 230°C Natural cooling Preheat : 150°C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 230±5°C Flux for lead free : rosin Dip Time : 4±1sec. 150°C 60 seconds 4±1 seconds Solder Heat Resistance 1. Appearance : No significant abnormality 2. Inductance change : Within ±20% Preheating 260°C Dipping Natural cooling Preheat : 150°C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 260±5°C Flux for lead free : rosin Dip Time : 10±0.5sec. 150°C 60 seconds 10±0.5 seconds Reliability Test High Temperature Life Test Low Temperature Life Test Thermal Shock Temperature : 85±5°C Time : 500±12 hours Measure at room temperature after placing for 2 to 3 hrs. 1. Appearance : No damage 2. Inductance : Within ±20% of initial value. No disconnection or short circuit. Temperature : -25±5°C Time : 500±12 hours Measure at room temperature after placing for 2 to 3 hrs. Conditions of 1 cycle. Step 1 2 3 4 Temperature (°C) -25±3 Room Temperature +85±3 Room Temperature Times (min.) 30±3 Within 3 30±3 Within 3 Total : 5 cycles Measure at room temperature after placing for 2 to 3 hrs. Humidity Resistance 1. Appearance : No damage 2. Inductance : Within ±20% of initial value. No disconnection or short circuit. Temperature : 40±5°C Humidity : 90% to 95% Applied Current : Rated Curent Time : 500±12 hours Measure at room temperature after placing for 2 to 3 hrs. NOTE : Specifications subject to change without notice. Please check our website for latest information. 12.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 3 SMD POWER INDUCTORS 7. SOLDERIND AND MOUNTING : 7-1. Recommended PC Board Pattern 12.6 7.0 SDC1205 SERIES 7-2. Soldering Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. 7-2.1 Solder Re-flow : Recommended temperature profiles for re-flow soldering in Figure 1. 7-2.2 Soldering Iron (Figure 2) : Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. Note : a) Preheat circuit and products to 150°C. b) 280°C tip temperature (max) c) Never contact the ceramic with the iron tip d) 1.0mm tip diameter (max) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f) Limit soldering time to 3 secs. Preheating TEMPERATURE °C 250~260 230 180 150 60~120s Soldering 5.4 TEMPERATURE °C 10s max. Natural cooling Preheating 280 260 150 Soldering Natural cooling 30~60s Over 1min. Gradual Cooling Within 3secs. Figure 1. Re-flow Soldering Figure 2. Iron Soldering NOTE : Specifications subject to change without notice. Please check our website for latest information. 12.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 4 SMD POWER INDUCTORS 8. PACKAGING INFORMATION : 8-1. Tape and Reel Dimension SDC1205 SERIES COVER TAPE 2.0±0.5 D B ØC A EMBOSSED CARRIER 220 220 220 220 220 Type 13" x 24mm A(mm) 24.0±0.1 B(mm) 100±1 C(mm) 13±0.5 D(mm) 330 8-3. Packaging Quantity Size Chip / Reel Reel Style SDC1205 500 13" x 24mm NOTE : Specifications subject to change without notice. Please check our website for latest information. 12.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 5