1H3

1H1THRU 1H8 HIGH EFFICIENCY RECTIFIERS Reverse Voltage - 50 to 1000 Volts R-1 Forward Current - 1.0 Ampere FEATURES 1.0 (25.4) MIN. 0.102 (2.6) 0.091 (2.3) DIA. 0.140(3.50) 0.114(2.90) The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 High speed switching for high efficiency Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 250 C/10 seconds,0.375”(9.5mm) lead length, 5 lbs. (2.3kg) tension MECHANICAL DATA 1.0 (25.4) MIN. 0.025 (0.65) 0.021 (0.55) DIA. Dimensions in inches and (millimeters) Case: R-1 molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight:0.007 ounce, 0.20 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. SYMBOLS 1H1 1H2 1H3 1H4 1H5 1H6 1H7 1H8 UNITS VOLTS VOLTS VOLTS Amps Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375”(9.5mm) lead length at TA=25 C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 300 400 140 210 280 200 300 400 1.0 600 420 600 800 560 800 1000 700 1000 IFSM VF IR trr CJ RqJA TJ,TSTG 50 15.0 1.0 25.0 1.3 5.0 100.0 70 12.0 50.0 -65 to +150 1.70 Amps Volts uA ns pF C/W C Note:1.Reverse recovery condition IF=0.5A,IR=1.0A,Irr=0.25A 2.Measured at 1MHz and applied reverse voltage of 4.0V D.C. 3.Thermal resistance from junction to ambient at 0.375”(9.5mm)lead length,P.C.B. mounted www.shunyegroup.com RATINGS AND CHARACTERISTIC CURVES 1H1 THRU 1H8 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1- FORWARD CURRENT DERATING CURVE £PEAK FORWARD SURGE CURRENT, AMPERES 1.0 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 0.8 25 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 0.6 20 0.4 Single Phase Half Wave 60Hz Resistive or inductive Load 15 0.2 10 0 0 25 50 75 100 125 150 175 5.0 1 10 100 AMBIENT TEMPERATURE, C NUMBER OF CYCLES AT 60 Hz FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 1,000 10 FIG. 4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES TJ=25 C PULSE WIDTH=300 ms 1%DUTY CYCLE 100 1 TJ=100 C 10 0.1 1H1-1H3 1H4-1H5 1H6-1H8 0.01 0.2 0.6 1.0 1.4 1.8 2.0 1 TJ=25 C 0.1 0.01 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLEAGE, VOLTS PERCENT OF PEAK REVERSE VOLTAGE,% FIG. 5-TYPICAL JUNCTION CAPACITANCE 200 100 TJ=25 C FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/W 100 JUNCTION CAPACITANCE, pF 10 10 1 1H1-1H5 1H6-1H8 0.1 0.01 0.1 1 10 100 1 0.1 1.0 10 100 REVERSE VOLTAGE,VOLTS t,PULSE DURATION,sec. www.shunyegroup.com