6A1

6A05 THRU 6A10 GENERAL PURPOSE SILICON RECTIFIER Reverse Voltage - 50 to 1000 Volts R-6 Forward Current - 6.0 Amperes FEATURES 1.0 (25.4) MIN. 0.360 (9.1) 0.340(8.6) DIA. 0.360(9.1) 0.340(8.6) The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 Construction utilizes void-free molded plastic technique Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 250 C/10 seconds,0.375”(9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.052 (1.3) 0.048 (1.2) DIA. MECHANICAL DATA Case: R-6 molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight:0.072 ounce, 2.05 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. SYMBOLS 6A05 6A1 6A2 6A4 6A6 6A8 6A10 UNITS VOLTS VOLTS VOLTS Amps Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375”(9.5mm) lead length at TA=60 C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 6.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Typical junction capacitance (NOTE 1) Typical thermal resistance (NOTE 2) Operating junction and storage temperature range VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 6.0 600 420 600 800 560 800 1000 700 1000 IFSM VF IR CJ RqJA TJ,TSTG 400 0.95 10.0 400 150 10.0 -65 to +175 Amps Volts uA pF C/W C Note:1.Measured at 1MHz and applied reverse voltage of 4.0V D.C. 2.Thermal resistance from junction to ambient at 0.375” (9.5mm)lead length,P.C.B. mounted www.shunyegroup.com RATINGS AND CHARACTERISTIC CURVES 6A05 THRU 6A10 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1- FORWARD CURRENT DERATING CURVE £PEAK FORWARD SURGE CURRENT, AMPERES 6.0 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 400 4.8 320 3.6 240 2.4 Single Phase Half Wave 60Hz Resistive or inductive Load 160 1.2 80 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 0 0 25 50 75 100 125 150 175 0 1 10 100 AMBIENT TEMPERATURE, C NUMBER OF CYCLES AT 60 Hz FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 200 1,000 100 FIG. 4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES 100 TJ=150 C 10 10 1 TJ=25 C PULSE WIDTH=300 ms 1%DUTY CYCLE TJ=100 C 1 0.1 0.5 0.7 0.9 1.1 1.3 1.4 0.1 TJ=25 C 0.01 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLEAGE, VOLTS PERCENT OF PEAK REVERSE VOLTAGE,% FIG. 5-TYPICAL JUNCTION CAPACITANCE TRANSIENT THERMAL IMPEDANCE, C/W 2000 1000 TJ=25 C 100 FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE JUNCTION CAPACITANCE, pF 10 100 1 0.1 0.01 0.1 1 10 100 10 0.1 1.0 10 100 REVERSE VOLTAGE,VOLTS t,PULSE DURATION,sec. www.shunyegroup.com