MB2S

SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIERS Voltage Range - 200 to 1000 Volts Current - 0.5/0.8 Ampere FEATURES Ideal for printed circuit board Reliable low cost construction utilizing molded plastic technique High temperature soldering guaranteed: 260*/10 seconds at 5 lbs., (2.3kg) tension Small size, simple installation Leads solderable per MIL-STD-202, Method 208 High surge current capability MBS .193(4.90) .177(4.50) .033(0.84 .022(0.56) MBS SERIES .157(4.00) .142(3.60) .276(7.0) + MAX .102(2.60) .087(2.20) .106(2.70) .090(2.30) .053(1.53) .037(0.95) .014(0.35) .006(0.15) MECHANICAL DATA Case: Molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting Position: Any Weight:0.04 ounce, 1.0 grams .008(0.20) MAX .118(3.0) MAX .083(2.12) .043(1.10) .043(1.10) .028(0.70) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25* ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load, for capacitive load derate current by 20%. SYMBOLS MB2S 200 140 200 MB4S 400 280 400 MB6S 600 420 600 0.5 0.8 35 1.0 5.0 100 15 75 -55 to +150 -55 to +150 MB8S 800 560 800 MB10S 1000 700 1000 UNITS VOLTS VOLTS VOLTS Amps Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TA=30* On glass-epoxy P.C.B. On aluminum substrate Peak forward surge current, 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage drop per leg at 0.4A Maximum DC reverse current TA=25* at rated DC blocking voltage TA=100* Typical junction capactiance per leg(Note3) Typical thermal resistance per leg Operating temperature range storage temperature range VRRM VRMS VDC IF(AV) IFSM VF IR CJ R* JA TJ TSTG Amps Volts uA uA pF */W * * NOTES:1.On glass epoxy P.C.B. mounted on 0.05x0.05''(1.3x1.3mm) pads 2.On aluminum substrate P.C.B. with on area of 0.8''x0.8''(20x20mm) mounted on 0.05X0.05''(1.3X1.3mm) solder pad 3.Measured at 1.0MHz and applied reverse valtage of 4.0 volts. www.shunyegroup.com RATINGS AND CHARACTERISTIC CURVES MBS SERIES AVERAGE FORWARD RECTIFIED CURRENT(A) FIG. 1- DERATING CURVE OUTPUT RECTIFIED CURRENT FOR 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 Aluminum Substrate PEAK FORWARD SURGE CURRENT.(A) FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PERLEG 35 30 25 20 15 10 5 0 Ta=40* Single Half Sine-Wave (JEDEC Method) f=60Hz Glass Epoxy P.C.B. f=50Hz 1Cycle 1 10 100 0 20 40 60 80 100 120 140 160 AMBIENT TEMPERATURE,(*) NUMBER OF CYCLES INSTANTANEOUS REVERSE LEAKAGE CURRENT.(uA) FIG. 3-TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG 100 FIG. 4-TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD CURRENT(A) 10 TJ=150* TJ=25* 1 10 TJ=125* 1 0.1 TJ=25* Pulse Width=300*s 1% Duty Cycle 0.1 TJ=25* 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.01 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE.(V) PERCENT OF RATED PEAK REVERSE VOLTAGE(%) JUNCTION CAPACITANCE.(pF) FIG. 5-TYPICAL JUNCTION CAPACTITANE PER LEG 30 25 20 15 10 5 0 TJ=25* f=1.0MHZ Vsig=50mV p-p 0.1 1 10 100 200 REVERSE VOLTAGE.(V) www.shunyegroup.com