SM89T16R1C25

SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Product List SM89T16R1L16, 16MHz 64KB internal flash MCU SM89T16R1C25, 25MHz 64KB internal flash MCU Feature Working Voltage: 3.3V or 5.0V. 80C51 Central Processor Unit (CPU), High-Speed Architecture (4 clocks / machine cycle), the maximum clock rate is 25 MHz. 64K x 8 on chip flash memory can be programmed at VPP = 12V 1280 x 8 RAM (On-Chip 256 bytes and Expand 1024 bytes), expandable externally to 64KB Two standard 16-bits timers/counters An additional 16-bits timer/counter coupled to a capture and compare register. Two 8-bits / 5-bits resolution Pulse-Width-Modulation (PWM) outputs. Four channels 6 bits Analog to Digital Converter (ADC). Four 8-bits I/O ports.(For PDIP package) Four 8-bits I/O ports plus one 4-bits I/O port. (For PLCC or PQFP package) Two Full-duplex Enhance UART Two DPTR (either data pointer can be incremented and decrement). 13 interrupt sources (default 6 + int2, int3, int4, int5, UART1, ADC, RTC) with 2 priority levels. RTC (Real Time Clock) function. Extended temperature range (-40℃ to +85℃) Software enable/disable ALE output pulse Wake-up from POWER-DOWN mode by external interrupt, RTCI or H/W Reset. General Description The SM89T16R1 is a high speed (4 clocks / machine cycle) single-chip 8-bits microcontroller manufactured in an advanced CMOS process with on chip flash memory. It supports a derivative of the 80C51 microcontroller family. The SM89T16R1 has the same instructions set as the 80C51. The SM89T16R1 contains a 64KB on chip program flash, a volatile 1280 x 8 bits data RAM, four 8-bits I/O ports, one 4-bits I/O port, two 16-bits timer/event counters, and an additional 16-bits timer coupled to capture and compare latches, a two-priority-level, nested interrupt structure, two pulse-width- modulation outputs, two UART and two DPTR, an on-chip oscillator and timing circuit. For system that requires extra capability the SM89T16R1 can be expanded using standard TTL compatible memory and logic. In addition, The SM89T16R1 has two software selectable modes of power saving – IDLE mode and POWER-DOWN mode. The IDLE mode freezes the CPU while allowing the RAM, timer, serial ports, and interrupt system to continue functioning. The POWER-DOWN mode saves the RAM contents but freezes the oscillator, causing all other chip functions to be inoperative. The Power Management Mode (PMM) is useful for portable or battery-powered applications. This feature allows software to select a lower speed clock as the main time base. Ordering Information SM89T16R1ihhkL yymmv i: process identifier {L=3.0V~3.6V,C=4.5V~ 5.5V} hh: working clock in MHz {16,25} k: package type postfix {as below table} yy: year mm: month v: version identifier { , A, B, ...} L: PB Free identifier {No text is Non-PB Free,”P” is PB Free} 1 Taiwan 6F, No.10-2 Li- Hsin 1st Road , Science-based Industrial Park, Hsinchu, Taiwan 30078 TEL: 886-3-567-1820 886-3-567-1880 FAX: 886-3-567-1891 886-3-567-1894 Specifications subject to change without notice contact your sales representatives for the most recent information. Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. Package Spec. Package 44L PQFP 44L PLCC SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Pin / PAD Figure 1 Figure 2 Figure 3 Frequency 16 MHz at 3.3V and 25MHz at 5V 16 MHz at 3.3V and 25MHz at 5V 16 MHz at 3.3V and 25MHz at 5V 40L PDIP Pin Configuration Figure 1 44L PQFP Package Figure 2 44L PLCC Package P1.4/INT2/PWM0 P1.2/RXD1 P1.3/TXD1 P1.1/T2EX P0.0/AD0 P0.1/AD1 P0.2/AD2 41 P2.7/A15/ADC3 P2.6/A14/ADC2 P2.5/A13/ADC1 ALE/X32OUT #PSEN/X32IN P0.6/AD6 P0.4/AD4 P0.5/AD5 P0.7/AD7 #EA P4.1 6 PWM1/#INT3/P1.5 22 P2.4/A12/ADC0 21 P2.3/A11 20 P2.2/A10 19 P2.1/A9 18 P2.0/A8 17 P4.0 16 VSS 15 XTAL1 14 XTAL2 13 P3.7/#RD 12 P3.6/#WE 5 4 3 2 1 44 43 42 33 AD3/P0.3 34 AD2/P0.2 35 AD1/P0.1 36 AD0/P0.0 37 VDD 38 P4.2 39 T2/P1.0 40 T2EX/P1.1 41 RXD1/P1.2 42 TXD1/P1.3 43 PWM0/INT2/P1.4 44 1 PWM1/#INT3/P1.5 32 31 30 29 28 27 26 25 24 23 7 8 9 10 11 12 13 14 15 16 17 18 #WE/P3.6 19 #RD/P3.7 20 XTAL2 21 XTAL1 22 VSS 23 P4.0 24 A8/P2.0 25 A9/P2.1 26 A10/P2.2 27 A11/P2.3 28 ADC0/A12/P2.4 P0.3/AD3 40 39 P0.4/AD4 38 P0.5/AD5 37 P0.6/AD6 36 P0.7/AD7 35 #EA 34 P4.1 33 ALE/X32OUT 32 #PSEN/X32IN 31 P2.7/A15/ADC3 30 P2.6/A14/ADC2 29 P2.5/A13/ADC1 P1.0/T2 INT4/P1.6 #INT5/P1.7 RES RXD/P3.0 P4.3 TXD/P3.1 #INT0/P3.2 #INT1/P3.3 T0/P3.4 T1/P3.5 2 INT4/P1.6 3 #INT5/P1.7 4 RES 5 RXD/P3.0 6 P4.3 7 TXD/P3.1 8 #INT0/P3.2 9 #INT1/P3.3 10 T0/P3.4 11 T1/P3.5 Figure 3 40L PDIP Package P2.7/A15/ADC3 P2.6/A14/ADC2 P2.5/A13/ADC1 P2.4/A12/ADC0 P0.1/AD1 P0.2/AD2 P0.3/AD3 #PSEN/X32IN ALE/X32OUT P0.0/AD0 P0.4/AD4 P0.5/AD5 P0.6/AD6 P0.7/AD7 P2.3/A11 P2.2/A10 P2.1/A9 40 39 38 37 36 35 34 33 32 31 #EA 30 29 28 27 26 25 24 23 22 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 XTAL2 T0/P3.4 T2/P1.0 TXD/P3.1 T1/P3.5 T2EX/P1.1 #WE/P3.6 XTAL1 RES TXD1/P1.3 INT4/P1.6 RXD/P3.0 RXD1/P1.2 #INT0/P3.2 PWM0/INT2/P1.4 Specifications subject to change without notice contact your sales representatives for the most recent information. PWM1/#INT3/P1.5 #INT5/P1.7 #INT1/P3.3 #RD/P3.7 VSS 20 21 P2.0/A8 VDD 2 Ver 2.1 SM89T16R1 08/2006 VDD P4.2 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Block Diagram RxD (3) T2EX INT5 INT4 INT3 INT2 TxD (3) T2 PWM0 PWM1 TxD1 RxD1 (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) Xtal1 Xtal2 EA CPU ALE PSEN RD (3) WR (3) UART Int-RAM 256x8 UART1 FLASH 64Kx8 Ext-RAM 1024x8 PWM Timer2 Expand Interrupt/ Wake Up C51 CORE iBUS Timer0 Timer1 INT / PDWU RTC Parallel I/O ports & Ext. Bus Port0 Port1 Port2 Port3 Port4 ADC (3) (3) (3) (3) (4) (4) (2) (2) (2) (2) X32OUT X32IN T0 T1 INT0 ADC3 ADC2 ADC1 ADC0 INT1 P0 P4 P1 P2 P3 Notes: Specifications subject to change without notice contact your sales representatives for the most recent information. RES (1): Alternate function of P1 (2): Alternate function of P2 (3): Alternate function of P3 (4): Alternate function of ALE, PSEN 3 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Pin Description MNEMONIC VDD P0.0 – P0.7 DIP 40 pin 40 39,38,37,36 35,34,33,32 PQFP 44 Pin 38 37,36,35,34 33,32,31,30 PLCC 44 pin 44 43,42,41,40 39,38,37,36 Names and Functions Power supply: +3.3V and +5V power supply pin during normal operations and power saving modes. Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to them become floating and can be used as high- impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external program and data memory. In this application, it uses strong internal pull-ups when emitting 1s. Port Pin Alternative function P0.0 AD0 P0.1 AD1 P0.2 AD2 P0.3 AD3 P0.4 AD4 P0.5 AD5 P0.6 AD6 P0.7 AD7 Port 1: An 8-bits bidirectional I/O port with internal pull-ups on all pins. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: IIL). Alternate function of SM89T16R1 include: Port Pin Alternative function P1.0 T2: TIMER2 clock output P1.1 T2EX: TIMER2 reload/capture DIR. P1.2 RxD1: UART1 input P1.3 TxD1: UART1 output P1.4 PWM0: PWM channel 0 output INT2: rising edge trigger P1.5 PWM1: PWM channel 1 output #INT3: falling edge trigger P1.6 INT4: rising edge trigger P1.7 #INT5: falling edge trigger Reset: A high on this pin for two machine cycles while the oscillator is running resets the device. An internal resistor to VSS permits a power-on reset using only an external capacitor to VCC. Port 2: Port 2 is an 8-bits bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 2 pins that are externally being pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: IIL). Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that uses 16-bits addresses (MOVX @DPTR). In this application, it uses strong internal pull-ups when emitting 1s. During accesses to external data memory that uses 8-bits addresses (MOV @Ri), port 2 emits the contents of the P2 special function register. Port Pin Alternative function P2.0 A8 P2.1 A9 P2.2 A10 P2.3 A11 P2.4 A12/ADC0 P2.5 A13/ADC1 P2.6 A14/ADC2 P2.7 A15/ADC3 P1.0 – P1.7 1,2,3,4, 5,6,7,8 40,41,42,43, 44,1,2,3 2,3,4,5, 6,7,8,9 RST 9 4 10 P2.0 – P2.7 21,22,23,24, 25,26,27,28 18,19,20,21 22,23,24,25 24,25,26,27, 28,29,30,31 MNEMONIC DIP 40 pin PQFP 44 Pin PLCC 44 pin 4 Names and Functions Ver 2.1 SM89T16R1 08/2006 Specifications subject to change without notice contact your sales representatives for the most recent information. SyncMOS Technologies International, Inc. P3.0 – P3.7 10,11,12,13 14,15,16,17 5,7,8,9, 10,11,12,13 11, 13,14,15, 16,17,18,19 SM89T16R1 Port 3: Port 3 is an 8-bits bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source current because of the pull-ups. (See DC Electrical Characteristics: IIL). Port 3 also serves the special features. Port Pin Alternative function P3.0 RxD UART input P3.1 TxD UART output P3.2 #EX0 external interrupt 0 P3.3 #EX1 external interrupt 1 P3.4 T0: Timer 0 external input P3.5 T1: Timer 1 external input P3.6 #WR External data memory write strobe P3.7 #RD External data memory read strobe Address Latch Enable: Output pulse for latching the low byte of the address during an access to external memory. In normal operation, ALE is emitted twice every machine cycle, and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory. Setting SFR SCONF.0 can disable ALE. With this bit set, ALE will be active only during a MOVX instruction. X32OUT: The 32.768KHz crystal output for RTC function. Program Store Enable: The read strobe to external program memory. When executing code from the external program memory, #PSEN is activated twice each machine cycle, except that two #PSEN activations are skipped during each access to external data memory. #PSEN is not activated during fetches from internal program memory. X32IN: The 32.768KHz crystal input for RTC function. External Access Enable: #EA must be externally held low to enable the device to fetch code from external program memory locations. If #EA is held high, the device executes from internal program memory. Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits. Crystal 2: Output from the inverting oscillator amplifier. 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded ALE/X32OUT 30 27 33 #PSEN/X32IN 29 26 32 #EA 31 29 35 XTAL1 XTAL2 19 18 15 14 21 20 SFR Mapping The special function register of SM89T16R1 fall into the following categories C51 CORE register: ACC, B, DPL, DPH, PSW, SP I/O ports: P0,P1, P2, P3, P4 Timer/Counter register: T2CON, T2MOD, TCON, TMOD, TH0, TH1, TH2, TL0, TL1, TL2, RCA2PL, RCAP2H The Second DPTR register: DPS, DPH1, DPL1 UART I/O register: SBUF, SCON UART1 I/O register: SBUF1, SCON1 ADC register: ADCSC, ADCD, P2CON Power and system control register: PCON, SCONF Interrupt system register: IP, IE, IP1, IE1, IFR Expand External Interrupt register: EIE, EIP, EXIF RTC register: RTCC, RTCS PWM output register: PWMC0, PWMC1, PWMD0, PWMD1, P1CON PMM (Power Management) register: PMR Specifications subject to change without notice contact your sales representatives for the most recent information. 5 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Table 1 SFR Map $F8 $F0 $E8 $E0 $D8 $D0 $C8 $C0 $B8 $B0 $A8 $A0 $98 $90 $88 $80 IP x000 0000 P3 1111 1111 IE 0000 0000 P2 1111 1111 SCON 0000 0000 P1 1111 1111 TCON 0000 0000 P0 1111 1111 IP1 0000 0000 IE1 0000 0000 RTCS 0000 0000 SBUF xxxx xxxx EXIF 0000 1xxx TMOD 0000 0000 SP 0000 0111 EIP xxxx 0000 IFR 0000 0000 RTCC 0000 0000 LEDP0 0000 0000 TL0 0000 0000 DPL 0000 0000 PWMD0 0000 0000 EIE 0000 0000 CKCON 0000 0001 P1CON 0000 0000 LEDP1 0000 0000 TL1 0000 0000 DPH 0000 0000 PWMD1 0000 0000 DPL1 0000 0000 P2CON 0000 0000 LEDP2 0000 0000 TH0 0000 0000 DPH1 0000 0000 LEDP3 0000 0000 TH1 0000 0000 DPS 0000 0000 LEDP4 0000 0000 ADCSC 0000 0000 SCONF 0000 0000 ACC 0000 0000 P4 xxxx 1111 PSW 0000 0000 T2CON 0000 0000 SCON1 0000 0000 B 0000 0000 SBUF1 xxxx xxxx SADEN 0000 0000 SADDR 0000 0000 PMR 01xx 0000 T2MOD 0000 0000 SADEN1 0000 0000 SADDR1 0000 0000 RCAP2L 0000 0000 PWMC0 0000 0000 RCAP2H 0000 0000 PWMC1 0000 0000 TL2 0000 0000 TH2 0000 0000 $FF $F7 $EF $E7 $DF $D7 $CF $C7 $BF $B7 $AF $A7 $9F $97 ADCD 0000 0000 PCON 00xx 0000 $8F $87 Table 2 All SFR list (ADC, RTC, PWM, LED Driving Capability Control) Symbol ADCSC ADCD RTCS RTCC PWMC0 PWMC1 PWMD0 PWMD1 LEDP 0 LEDP 1 LEDP 2 LEDP 3 LEDP 4 Description ADC status & control ADC data register RTC Status RTC Control PWM 0 Control PWM 1 Control PWM 0 Data PWM 1 Data LED output in P0 LED output in P1 LED output in P2 LED output in P3 LED output in P4 Direct 8EH 8FH A1H A2H D3H D4H B3H B4H 92H 93H 94H 95H 96H Bit 7 COM AD.5 RTCen Int_sel.1 Bit 6 Bit 5 Bit 4 A/D Converter CON ADCSS1 ADCSS0 AD.4 AD.3 AD.2 Real Timer Clock (RTC) Stable Sec.5 Sec.4 Int_sel.0 Min.5 Min.4 PWM output PWMD.5 PWMD.5 PWMD.4 PWMD.4 Bit 3 CH1 AD.1 Sec.3 Min.3 Bit 2 CH0 AD.0 Sec.2 Min.2 PBS PBS Bit 1 Bit 0 RESET 00H 00H Sec.1 Min.1 PFS1 PFS1 PWMD.1 PWMD.1 Sec.0 Min.0 PFS0 PFS0 PWMD.0 PWMD.0 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H PWMD.7 PWMD.7 PWMD.6 PWMD.6 PWMD.3 PWMD.3 PWMD.2 PWMD.2 LED Driving Capability Control Specifications subject to change without notice contact your sales representatives for the most recent information. 6 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Table 3 : All SFR list (8051, I/O, Timer, UART/UART1, System, Interrupt) Symbol ACC* B SP PSW* DPTR DPH DPL P0* P1* P2* P3* P4* P1CON P2CON TCON* THL0 TH0 TL0 THL1 TH1 TL1 T2CON* T2MOD RCAP2HL Description Accumulator B register Stack Pointer Process Status Data Pointer (2 Bytes) Data Pointer High Data Pointer Low Port 0 Port 1 Port 2 Port 3 Port 4 P1 Control P2 Control Timer Control register Timer 0 (2 Bytes) Timer 0 High Timer 0 Low Timer 1 (2 Bytes) Timer 1 High Timer 1 Low Timer 2 Control Timer 2 Mode Control Reload/Capture (2 bytes) RCAP2 High RCAP2 Low Time 2 (2 bytes) Timer 2 High Time 2 Low UART Control UART Buffer UART 1 Control UART 1 Buffer Slave Address Slave Address 1 Slave Address Mask Enable Slave Address 1 Mask Enable Data Pointer 1 (2 Bytes) Data Pointer 1 High Data Pointer 1 Low Data Point Select Power Control register System Control Power Management Register Interrupt Enable Interrupt Enable 1 Interrupt Flag 1 External Interrupt Enable Interrupt Priority Interrupt Priority 1 External Interrupt Priority Clock Control Direct E0 F0 81H D0H 83H 82H 80H 90H A0H B0H D8H 9BH 9CH 88H 8CH 8AH 8DH 8BH C8H C9H CBH CAH CDH CCH 98H 99H F8H F9H D9H DAH E9H EAH Bit 7 Bit 6 Bit 5 8051 Core Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RESET 00H 00H 07H 00H 00H 00H CY AC F0 RS1 RS0 OV P P0.7 P1.7 P2.7 P3.7 ADCE3 TF1 P0.6 P1.6 P2.6 P3.6 I/O PORT P0.5 P1.5 P2.5 P3.5 P0.4 P1.4 P2.4 P3.4 P0.3 P1.3 P2.3 P3.3 P4.3 P0.2 P1.2 P2.2 P3.2 P4.2 PWM1E PWM0E ADCE2 ADCE1 ADCE0 TIMER / Counter TF1 TF0 TR0 P0.1 P1.1 P2.1 P3.1 P4.1 IE0 P0.0 P1.0 P2.0 P3.0 P4.0 IT0 FFH FFH FFH FFH XFH 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H IE1 IT1 TF2 HC5 EXF2 HC4 RCLK HC3 TCLK HC2 EXEN2 T2CR TR2 CT2 T2OE CPRL2 DCEN RCAP2H RCAP2L THL2 TH2 TL2 SCON* SBUF SCON1 SBUF1 SADDR SADDR1 SADEN SADEN1 DPTR1 DPH1 DPL1 DPS PCON SCONF PMR IE* IE1 IFR EIE IP* IP1 EIP CKCON SM0/FE SM0_1/FE_1 SM1 UART & UART1 SM2 REN SM2_1 REN_1 TB8 TB8_1 RB8 RB8_1 TI TI_1 RI RI_1 SM1_1 00H XXH 00H XXH 00H 00H 00H 00H Data Point 1 A5H A4H A6H 87H BFH D1H A8H A9H AAH ABH B8H B9H BAH A3H SMOD SMOD1 CD1 EA Power and System SMOD0 PDWUE CD0 ES1 Interrupt system ET2 ES0 XTOFF ET1 EADC ADCIF EX5 PT1 PADC PX5 T0M EX1 ERTC RTCIF EX4 PX1 PRTC PX4 MD2 ET0 EX3 PT0 PX3 MD1 EX0 EX2 PX0 PX2 MD0 PD OME 00H 00H 00H 00H 00H 40H 00H 00H 00H 00H 00H 00H X0H 01H DPS.0 IDLE ALEI PS1 PT2 Clock Control T2M PS0 T1M Specifications subject to change without notice contact your sales representatives for the most recent information. 7 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Operating Conditions Symbol TA VCC33 VCC5 Fosc 16 Fosc 25 Description Operating temperature Supply voltage Supply voltage Oscillator Frequency Oscillator Frequency Min. -40 3.0 4.5 Typ. 25 3.3 5.0 Max. 85 3.6 5.5 16 25 Unit. ℃ V V MHz MHz Remarks Ambient temperature under bias For 3.3V application For 5.0V application DC Characteristic VCC = 5V (±10%), VSS=0V TA= -40℃ to 85℃ SYMBOL VCC ICC IID IPD Supply Voltage Supply current operating Supply current IDLE Mode Supply current Power-Down MODE RTC Disable Supply current Power-Down MODE RTC Enable Input LOW voltage, P0, P1, P2, P3, P4, /EA Input LOW voltage, RES, XTAL1 Input HIGH voltage, P0, P1, P2, P3, P4, /EA Input HIGH voltage, RES, XTAL1 Input current LOW level Port 1,2,3,4 Transition current High to Low Port 1,2,3,4 Input leakage current Output LOW voltage, Port 0,ALE, /PSEN Output LOW voltage, Port 1, 2, 3, 4 Output High voltage Port0 ALE, /PSEN Output High voltage Port 1,2,3,4 Internal RESET pull-down resistor Pin capacitance See notes 1 fCLK = 12MHz VCC = 5.0V See note 2 fCLK = 12MHz VCC = 5.0V See note 3；VCC = 5.5V See note 3；VCC = 5.5V INPUT VIL1 VIL2 VIH1 VIH2 IIL ITL ILI VOL1 VOL2 VOH1 VOH1 RRST CIO -0.5 0 2.0 70%VCC VIN = 0.45V VIN = 2.0 V 0.45V < VIN < VCC-0.3V OUTPUT IOL = 3.2mA，VCC=5.0V IOL = 1.6mA，VCC =5.0V IOH = -800uA，VCC =5.0V IOH = -60µA，VCC =5.0V Test freq=1MHz, TA=25℃ 0.8 0.8 Vcc+0.5 Vcc+0.5 -75 -650 ±10 0.45 0.45 2.4 2.4 50 V V V V µA µA µA V V V V kΩ pF PARAMETER TEST CONDITIONS LIMITS MIN MAX 4.5 5.5 30 15 30 100 UNIT V mA mA µA uA 300 10 VCC = 3.3V (±10%), VSS=0V , TA=-40℃ to 85℃ SYMBOL VCC ICC IID IPD Supply Voltage See notes 1 Supply current operating fCLK = 12MHz VCC = 3.6V See note 2 Supply current IDLE Mode fCLK = 12MHz VCC = 3.6V See note 3；VCC = 3.6V Supply current Power-Down MODE RTC Disable See note 3；VCC = 3.6V Supply current Power-Down MODE RTC Enable INPUT Input LOW voltage, P0, P1, P2, P3, P4, /EA Input LOW voltage, RST,XTAL1 Input HIGH voltage, P0, P1, P2, P3, P4, /EA Input HIGH voltage, RST Input HIGH voltage, XTAL1 VCC = 3.6V VCC = 3.6V VCC = 3.6V VCC = 3.6V VCC = 3.6V 0 0 0 0.6 VCC -0.4 0.6 VCC PARAMETER TEST CONDITIONS MIN 3.0 LIMITS MAX 3.6 20 10 20 30 0.2 VCC -0.2 0.2 VCC -0.2 0.2 VCC -0.2 VCC + 0.2 VCC + 0.2 UNIT V mA mA µA µA V V V V V VIL1 VIL2 VIH1 VIH2 VIH3 Specifications subject to change without notice contact your sales representatives for the most recent information. 8 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. -0.4 IIN1 ITL ILI VOL1 VOL2 VOH1 VOH2 ISK1 ISK2 ISR1 ISR2 RRST CIO Input current LOW level Port 1,2,3,4 Transition current High to Low Port 1,2,3,4 Input leakage current P0, /EA Output Low voltage, Port 0,ALE, /PSEN Output Low voltage Port 1,2,3,4 Output High voltage Port0, ALE, /PSEN Output High voltage Port 1,2,3,4 Sink Current Port 1, 2, 3, 4 Sink Current Port 0,ALE, /PSEN Source Current Port 1, 2, 3, 4 Source Current Port 0,ALE, /PSEN Internal RESET pull-down resistor Pin capacitance VCC = 3.0V ~3.6V, VIN = 0.45V. See note 4 VCC = 3.6V, VIN = 1.2 V VCC = 3.0V ~3.6V, 0.45V0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 tMCS =0 Specifications subject to change without notice contact your sales representatives for the most recent information. 10 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. 2.5 tCLCL–5 -5 1.0 tCLCL -5 1.0 tCLCL -5 2.0 tCLCL -5 0 1.0 tCLCL -5 SM89T16R1 tMCS >0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 tMCS =0 tMCS >0 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded tQVWX tWHQX tRLAZ tWHLH 9 9 8 8,9 Data valid to /WR transition Data hold after /WR /RD LOW to address float /RD or /WR HIGH to ALE HIGH ns ns 0.5 tCLCL–5 10 1.0 tCLCL +5 ns ns Notes: tMCS is time period related to the Stretch memory cycle selection. The following table shows the value of tMCS for each Stretch selection. M2 0 0 0 0 1 1 1 1 M1 0 0 1 1 0 0 1 1 M0 0 1 0 1 0 1 0 1 Figure 10 10 10 10 10 MOVX Cycles 2 machine cycles 3 machine cycles 4 machine cycles 5 machine cycles 6 machine cycles 7 machine cycles 8 machine cycles 9 machine cycles Symbol tXLXL tQVXH tXHQX tXHDX tXHDV Min tMCS 0 4 tCLCL 8 tCLCL 12 tCLCL 16 tCLCL 20 tCLCL 24 tCLCL 28 tCLCL Typ 12 tCLCL 4 tCLCL 12 tCLCL 4 tCLCL 12 tCLCL 4 tCLCL 12 tCLCL 4 tCLCL 12 tCLCL 4 tCLCL Max Unit ns ns ns ns ns ns ns ns ns ns Parameter Serial Port Clock Cycle Time SM2=0,12 clocks per cycle SM2=1,4 clocks per cycles Output Data Setup to Clock Rising SM2=0,12 clocks per cycle SM2=1,4 clocks per cycles Output Data Hold to Clock Rising SM2=0,12 clocks per cycle SM2=1,4 clocks per cycles Input Data Hold to Clock Rising SM2=0,12 clocks per cycle SM2=1,4 clocks per cycles Clock Rising Edge to Input Data Valid SM2=0,12 clocks per cycle SM2=1,4 clocks per cycles tCHCX VIH1 0.8V tCLCH tCHCL tCLCX tCLCL Figure 4 External Clock Drive waveform 2.0V 0.8V Notes: Test Points 0.8V 2.0V Floating 2.0V 0.8V Notes: The float state is define as the point which PORT 0 pins sinks 3.2mA or source 400µA at the voltage test level. 2.0V 0.8V AC inputs during testing are driven at 2.4V for logic “HIGH” and 0.45V for logic “LOW”. Timing measurements are at 2.0V for logic “HIGH” and 0.8V for logic “LOW” Figure 5 AC Testing Input/Output Figure 6 AC Testing, Floating Waveform Specifications subject to change without notice contact your sales representatives for the most recent information. 11 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. t LHLL ALE t LLPL t AVLL /PSEN t PLAZ t LLAX t LLIV PORT0 A0-A7 t AVIV2 t AVIV1 PORT2 A8-A15 A8-A15 INSTR IN t PXIZ t PXIX t PLIV t PLPH SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded A0-A7 A8-A15 Figure 7 External Program Memory Read Cycle t LLHL2 ALE t WHLH /PSEN t LLWL t LLAX1 /RD t AVLL t LLDV t RLRH t RLDV t t AVWL1 RLAZ t RHDZ t RHDX DATA IN A0-A7 PORT0 Instruction IN A0-A7 t AVIV1 t AVIV2 PORT2 A8-A15 A8-A15 A8-A15 Figure 8 External Data Memory Read cycle t LLHL2 ALE t WHLH /PSEN t LLAX2 t LLWL /WR t AVLL t AVWL1 PORT0 Instruction IN A0-A7 t AVDV2 PORT2 A8-A15 A8-A15 A8-A15 DATA OUT t QVWX t LWHQX A0-A7 t WLWH Figure 9 External Data Memory Write cycle UART (Synchronous Mode) High Speed Operation SM2=1 => TXD Clock =XTAL/4 ALE /PSEN WRITE_TO_SBUF t TXD_DATA_OUT D0 t TXD_CLOCK t TI WRITE_TO_SCON_TO_CLEAN_RI QVXH D1 XHQX D2 t D3 XHDX D4 D5 D6 D7 D8 XLXL RXD_DATA_IN D0 t D1 XHDV D2 D3 D4 D5 D6 D7 D8 TXD_CLOCK RI Figure 10 UART Mode 1Timing Specifications subject to change without notice contact your sales representatives for the most recent information. 12 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 UART (Synchronous Mode) SM2=0 => TXD Clock =XTAL/12 ALE /PSEN WRITE_TO_SBUF TXD_DATA_OUT TXD_CLOCK TI WRITE_TO_SCON_TO_CLEAN_RI 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded D0 D1 D6 D7 RXD_DATA_IN TXD_CLOCK RI D0 D1 D6 D7 Figure 11 UART Mode 0 Timing Function Description The SM89T16R1 is a High-Speed (4 clocks/machine cycle) stand-alone high-performance microcontroller designed for use in 3V/5V application, such as LCD monitor, instrumentation, or high-end consumer applications. In addition to the 80C51 standard functions, the device provides a number of dedicated hardware functions for these applications. The SM89T16R1 is a control-oriented CPU with on-chip program and data memory. It can be extended with external data memory up to 64K bytes. For system requiring extra capability, the SM89T16R1 can be enhanced by using external memory and peripherals. The SM89T16R1 has two software selectable modes of saving power consumption-IDLE and POWER-DOWN. The IDLE mode freezes the CPU while allowing the RAM, timer, serial ports and interrupt system to continue functioning. The POWER-DOWN mode save the RAM contents but freezes the oscillator causing all other chip functions to be inoperative. The POWER-DOWN mode can be terminated by H/W reset, or by any one of the six external interrupt or RTC function. CPU The CPU of SM89T16R1 is High-Speed 80C51. The structure of this CPU is shown as FIGURE 12. It contains Instruction Register (IR), Instruction Decoder, Program Counter (PC), Accumulator (ACC), B Register, and control logic. This CPU provides an 8-bits bi-direction bus to communicate with other blocks in the chip. The address and data are transferred through on the same 8-bits bus. Specifications subject to change without notice contact your sales representatives for the most recent information. 13 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded PROG. ADDR. ACC IRQ RES CLK Timing & Reset CONTROL LOGIC TMP2 TMP1 PROGRAM ADDR.REGISTER BUFFER CTRL. BUS PROGRAM INCREMENT PROGRAM COUNTER PSW DPTR DATA IN/OUT PCON POWER CTRL Signal INSTRUCTION DECODER SP INSTRUCTION REGISTER B Register ALU Figure 12 The CPU Structure CPU Timing The machine cycle consists of a sequence of 4 states, numbered S1 through S4. Only one-oscillator periods for each state time. Thus a machine cycle takes 4 oscillator periods. FIGURE 13 Shows relationships between oscillator, phase, and S1-S4. Sequence S1 S2 S3 S4 S1 S2 S3 S4 S1 S2 S3 S4 S1 S2 S3 S4 S1 S2 S3 S4 OSC (Xtal2) Machine Cycle M1 M2 M3 M4 M5 Figure 13 Sequences and Phases FIGURE 14 shows the fetch / execute sequences in states and phases for various kinds of instructions. Normally the program fetches are generated during each machine cycle, even if the instruction being executed doesn’t require it. If the instruction being executed doesn’t need more code bytes, the CPU simply ignores the extra fetch, and the PROGRAM COUNTER is incremented accordingly. Due to the reduced time for each instruction execution, both of the clocks edges are used for internal timing. Hence it is important that the duty cycle of the clock be as close to 50% as possible to avoid timing conflicts. The SM89T16R1 dose one op-code fetch per machine cycle. Therefore, in most of the instructions, the number of machine cycles needed to execute the instruction is equal to the number of bytes in the instruction. Of the 256 available op-codes, 128 of them are signal cycle instruction. See Figure14 shows the different cycle (A-D) instruction timing. Specifications subject to change without notice contact your sales representatives for the most recent information. 14 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. A.) Signal Cycle Instruction Timing Single_Cycle S1 CLK ALE /PSEN AD7-0 PORT_2 A7-A0 A15-A8 Data S2 S3 S4 SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded B.) Two Cycles Instruction Timing Instruction_Fetch S1 CLK ALE /PSEN AD7-0 PORT_2 A7-A0 OP-CODE A15-A8 A7-A0 OPERAND A15-A8 S2 S3 S4 S1 Operand_Fetch S2 S3 S4 C.) Three Cycles Instruction Timing Instruction_Fetch S1 CLK ALE /PSEN AD7-0 PORT_2 A7-A0 OP-CODE A15-A8 Instruction_Fetch S1 CLK ALE /PSEN AD7-0 PORT_2 A7-A0 OP-CODE A15-A8 A7-A0 OPERAND A15-A8 A7-A0 OPERAND A15-A8 A7-A0 OPERAND A15-A8 S2 S3 S4 S1 Operand_Fetch S2 S3 S4 S1 A7-A0 OPERAND A15-A8 Operand_Fetch S2 S3 S4 S1 A7-A0 OPERAND A15-A8 Operand_Fetch S2 S3 S4 S2 S3 S4 S1 Operand_Fetch S2 S3 S4 S1 Operand_Fetch S2 S3 S4 D.) Four Cycles Instruction Timing Figure 14 Timing of various instructions In standard 8032, the MOVX instructions take two machine cycles to execute. However in the SM89T16R1, the user has a facility to stretch the duration of this instruction from 2 machines cycle to 9 machines. The /RD and /WR strobe lines are also proportionately elongated. This gives the user flexibility in accessing both fast and slow peripherals without the use of external circuitry and with minimum software overhead. See FIGURE 15 Specifications subject to change without notice contact your sales representatives for the most recent information. 15 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded A) Data Memory Write with Stretch Value = 0(MOVX Instruction execute 2 machine cycles) MOVX_Instruction_cycle Last_Instruction S1 CLK ALE /PSEN WR_width /WR MOVX_Data_out MOVX_Inst. AD7-0 A7-A0 D7-D0 MOVX_Inst._Address Next_Inst._Address PORT_2 A15-A8 A15-A8 A15-A8 A15-A8 A7-A0 D7-D0 Next_inst._Read A7-A0 D7-D0 MOVX_Data_Address A7-A0 D7-D0 S2 S3 S4 First_Machine_cycle S1 S2 S3 S4 S1 S2 S3 S4 Next_Instruction Second_Machine_cycle S1 S2 S3 S4 B) Data Memory Write with Stretch Value = 1(MOVX Instruction execute 3 machine cycles)(Default) MOVX_Instruction_Cycle Second_Machine_cycle Last_Instruction S1 CLK ALE /PSEN WR_width /WR Next_inst._Read MOVX_Inst. AD7-0 A7-A0 D7-D0 A7-A0 D7-D0 A7-A0 MOVX_Data_out D7-D0 MOVX_Data_Address Next_Inst._Address PORT_2 A15-A8 A15-A8 A15-A8 A15-A8 A7-A0 D7-D0 S2 S3 S4 S1 S2 S3 S4 First_Machine_cycle S1 S2 S3 S4 S1 S2 S3 S4 Next_Instruction Third_Machine_Cycle S1 S2 S3 S4 MOVX_Inst._Address C) Data Memory Write with Stretch Value = 2(MOVX Instruction execute 4 machine cycles) MOVX_Instruction_Cycle 2'nd_Machine_cycle 1'st_Machine_cycle Last_Instruction S2 S1 CLK ALE /PSEN WR_width /WR Next_inst._Read MOVX_Inst. AD7-0 A7-A0 Next_Instruction 4'th_Machine_Cycle 3'rd_Machine_Cycle S4 S3 S1 S2 S3 S4 S1 S2 S3 S4 S1 S2 S3 S4 S1 S2 S3 S4 S1 S2 S3 S4 MOVX_Data_out D7-D0 A7-A0 D7-D0 A7-A0 D7-D0 MOVX_Data_Address A7-A0 D7-D0 MOVX_Inst._Address Next_Inst._Address PORT_2 A15-A8 A15-A8 A15-A8 A15-A8 Figure 15: MOVX Instruction Timing (Stretch=0~Stretch=2) Specifications subject to change without notice contact your sales representatives for the most recent information. 16 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Instruction Set The SM89T16R1 is High-Speed 80C51; it’s contained 4 clocks per machine. The SM89T16R1 dose one op-code fetch per machine cycle .It consists of 111 instructions used 40 single-cycle, 38 used two-cycles, 19 used three-cycles, and 10 used four-cycles. A summary of the instruction set is given in Table 4. Addressing Mode Notes on instruction set and address modes: Rn Direct @Ri #data #data16 addr11 Rel Bit Register R7-R0 of the currently selected register bank. 8-bits internal data location’s address. This could be internal DATA RAM location (0-127) or a SFR[i.e., I/O port, control register, status register, etc.(128-255) ] 8-bits RAM location addressed indirectly through register R1 or R0 of the actual register bank 8-bits constant included in the instruction 16-bits constant included in the instruction 11-bits destination address. Used by ACALL and AJMP. The branch can be anywhere within the same 2 Kbytes page of program memory as the first byte of the following instruction. Signed (2’s complement) 8-bits offset byte. Used by SJMP and all conditional jumps. Range is -128 to +127 bytes relative to first byte of the following instruction. Direct addressed bit in internal data RAM or SFR Table 4: summary of the instruction Mnemonic Arithmetic Instructions ADD A,Rn ADD A,direct ADD A,@Ri ADD A,#data ADDC A,Rn ADDC A,direct ADDC A,@Ri ADDC A,#data SUBB A,Rn SUBB A,direct SUBB A,@Ri SUBB A,#data INC A INC Rn INC direct INC @Ri DEC A DEC Rn DEC direct DEC @Ri INC DPTR DEC DPTR MUL AB DIV AB DA A Logical Instructions ANL A,Rn ANL A,direct ANL A,@Ri ANL A,#data ANL direct,A ANL direct,#data ORL A,Rn ORL A,direct ORL A,@Ri ORL A,#data ORL direct,A ORL direct,#data OPERATION A = A + Rn A = A + direct A = A + A = A + #data A = A + Rn + C A = A + direct + C A = A + @Ri + C A = A + #data + C A = A － Rn － C A = A － direct － C A = A － － C A = A－#data － C A=A+1 Rn = Rn + 1 direct = direct + 1 = + 1 A=A － 1 Rn = Rn － 1 direct = direct － 1 = － 1 DPTR = DPTR + 1 DPTR = DPTR － 1 B:A = A × B A = INT (A/B),B = MOD (A/B) Decimal adjust ACC A .AND. Rn A .AND. direct A .AND. A .AND. #data direct .AND. A direct .AND. #data A .OR. Rn A .OR. direct A .OR. A .OR. #data direct .OR. A direct .OR. #data BYTE 1 2 1 2 1 2 1 2 1 2 1 2 1 1 2 1 1 1 2 1 1 1 1 1 1 1 2 1 2 2 3 1 2 1 2 2 3 CYCLE 1 2 1 2 1 2 1 2 1 2 1 2 1 1 2 1 1 1 2 1 1 1 1 3 1 1 2 1 2 2 3 1 2 1 2 2 3 Specifications subject to change without notice contact your sales representatives for the most recent information. 17 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. XRL A,Rn XRL A,direct XRL A,@Ri XRL A,#data XRL direct,A XRL direct,#data CLR A CPL A RL A RLC A RR A RRC A SWAP A Data Transfers Instructions MOV A,Rn MOV A,direct MOV A,@Ri MOV A,#data MOV Rn,A MOV Rn,direct MOV Rn,#data MOV direct,A MOV direct,Rn MOV direct,direct MOV direct,@Ri MOV direct,#data MOV @Ri,A MOV @Ri,direct MOV @Ri,#data MOV DPTR,#data16 MOVC A,@A+DPTR MOVC A,@A+PC MOVX A,@Ri MOVX A,@DPTR MOVX @Ri,A MOVX @DPTR,A PUSH direct POP direct XCH A,Rn XCH A,direct XCH A,@Ri XCHD A,@Ri Boolean Instructions CLR C CLR bit SETB C SETB bit CPL C CPL bit ANL C,bit ANL C,/bit ORL C,bit ORL C,/bit MOV C,bit MOV bit,C JC rel JNC rel JB bit,rel JNB bit,rel JBC bit,rel Jump Instructions JZ rel JNZ rel JMP @A+DPTR A .XOR. Rn A .XOR. direct A .XOR. A .XOR. #data direct .XOR. A direct .XOR. #data A=0 A = /A Rotate ACC Left 1 bit Rotate Left through Carry Rotate ACC Right 1 bit Rotate Right through Carry Swap Nibbles in A A = Rn A = direct A = A = #data Rn = A Rn = direct Rn = #data direct = A direct = Rn direct = direct direct = direct = #data = A = direct = #data DPTR = #data16 A = code memory[A+DPTR] A = code memory[A+PC] A = external memory[Ri] (8-bits address) A = external memory[DPTR] (16-bits address) external memory[Ri] = A (8-bits address) external memory[DPTR] = A (16-bits address) INC SP: MOV “@’SP’, < direct > MOV < direct >, “@SP”: DEC SP ACC and < Rn > exchange data ACC and < direct > exchange data ACC and < Ri > exchange data ACC and @Ri exchange low nibbles C=0 bit = 0 C=1 bit = 1 C = /C bit = /bit C = C .AND. bit C = C .AND. /bit C = C .OR. bit C = C .OR. /bit C = bit bit = C Jump if C= 1 Jump if C= 0 Jump if bit = 1 Jump if bit = 0 Jump if C = 1 Jump if A = 0 Jump if A ≠ 0 Jump to A+ DPTR 1 2 1 2 2 3 1 1 1 1 1 1 1 1 2 1 2 1 2 2 2 2 3 2 3 1 2 2 3 1 1 1 1 1 1 2 2 1 2 1 1 1 2 1 2 1 2 2 2 2 2 2 2 2 2 3 3 3 2 2 1 SM89T16R1 1 2 1 2 2 3 1 1 1 1 1 1 1 1 2 1 2 1 2 2 2 2 3 2 2 1 2 2 3 3 3 2~9 2~9 2~9 2~9 2~9 2~9 1 2 1 1 1 2 1 2 1 2 2 2 2 2 2 2 3 3 4 4 4 3 3 2 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Specifications subject to change without notice contact your sales representatives for the most recent information. 18 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. DJNZ DJNZ CJNE CJNE CJNE CJNE ACALL AJMP LCALL LJMP SJMP RET RETI NOP Ri,rel Direct,rel A,direct,rel A,#data,rel @Ri,#data,rel Ri,#data,rel Address11 Address11 Address16 Address16 rel Decrement and jump if Rn not zero Decrement and jump if direct not zero Jump if A ≠ < direct > Jump if A ≠ < #data > Jump if Rn ≠ < #data > Jump if @Ri ≠ < #data > Call Subroutine only at 2k bytes Address Jump only At 2k bytes addressing Call Subroutine in max 64K bytes Address Jump to max 64K bytes Address Jump on at 256 bytes Return from subroutine Return from interrupt No Operation 2 3 3 3 3 3 2 2 3 3 2 1 1 1 SM89T16R1 3 4 4 4 4 4 3 3 4 4 3 3 3 1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Memory organization Program memory The program memory of SM89T16R1 consists of 64K bytes FLASH memory on chip. If during RESET, the /EA pin was held HIGH, the SM89T16R1 does not execute out of the internal program memory. If the /EA pin was held LOW during RESET the SM89T16R1 fetch all instructions from the external program memory. Internal Data memory The Data memory of SM89T16R1 consists of 1280 bytes internal data memory (256 bytes standard RAM and 1024 bytes AUX-RAM). The AUX-RAM is enable by SCONF.1 ($BF.1), and read/write by MOVX (Stretch=0, 2 machine fixed) Analog to Digital Converter (ADC) The ADC Block Diagram Shown as below: Those are only 4 pins mirror to Port 2[7:4] at Vin. The Digital output DATA [7:0] were put into ADCD ($8FH). And the ADC interrupt vector is 4BH. The ADC SFR is shown as below: ADSCR ($8EH) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 COM CON ADCSS1 ADCSS0 CH1 CH0 COM: Read only. When conversion complete, it will be set. CON: when set, the ADC will conversion continuous, else it will conversion only once. ADCSS [1:0]: ADC clock select. (ADC_CLK range 500 KHz~2.5 MHz).If over frequency of ADC_CLK, the conversion data may be unstable. ADCSS1 0 0 1 1 ADCSS0 0 1 0 1 CH0 0 1 0 1 ADC_CLK FOSC/4 FOSC/8 FOSC/16 FOSC/32 Input select CH0 CH1 CH2 CH3 CH [1:0]: ADC channel select. CH1 0 0 1 1 ADCD ($8FH) Bit7 AD.5 Bit6 AD.4 Bit5 AD.3 Bit4 AD.2 19 Bit3 AD.1 Bit2 AD.0 Bit1 Bit0 Specifications subject to change without notice contact your sales representatives for the most recent information. Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded V D D (= V re f) A D C SS1 A D C SS0 A D C _CLK 0 0 F o s c /4 0 1 F o s c /8 1 0 F o s c /1 6 1 1 F o s c /3 2 A D C S S [1 :0 ]= { A D S C R [5 :4 ]} A D C_CLK 6 6 -b it S A R A D C 4 3 C o m p le te { A D S C R .7 } D A T A < 5 :0 > { A D C D [7 :2 ]} V A I N < 3 : 0 > { P 2 .4 ~ P 2 .7 } C H < 2 :0 > { A D S C R [3 :2 ]} C o n t i n u o u s { A D S C R .6 } V SS Figure 16 ADC Block Diagram Dual UART Serial Port in the SM89T16R1 is a full duplex port. The SM89T16R1 provides the user with additional features such as the Frame Error Detection and the Automatic Address Recognition. The serial ports are capable of synchronous as well as asynchronous communication. In Synchronous mode the SM89T16R1 generates the clock and operates in a half duplex mode. In the asynchronous mode, full duplex operation is available. This means that it can simultaneously transmit and receive data. The transmit register and the receive buffer are both addressed as SBUF Special Function Register. However any write to SBUF will be to the transmit register, while a read from the receive buffer register. The serial port can operate in four different modes as described below. Mode 0 This mode provides synchronous communication with external devices. In this mode serial data is transmitted and received on the RxD line. TxD is used to transmit the shift clock. The TxD clock is provided by the SM89T16R1 whether the device is transmitting or receiving. This mode is therefore a half duplex mode of serial communication. In this mode, 8 bits are transmitted or received per frame. The LSB is transmitted / received first. The baud rate is fixed at 1/12 or 1/4 of the oscillator frequency. This baud rate is determined at the SM2 bit (SCON.5). When this bit is set to 0, then the serial port runs at 1/12 of the clock. When set to 1, the serial port runs at 1/4 of the clock. This additional facility of programmable baud rate in mode 0 is the only difference between the standard 8051 and the SM89T16R1. The function block diagram is shown below. Data enters and leaves the Serial port on the RxD line. The TxD line is used to output the shift clock. The shift clock is used to shift data into and out of the SM89T16R1 and the device at the other end of the line. Any instruction that causes a write to SBUF will start the transmission. The shift clock will be activated and data will shifted out on the RxD pin till all 8 bits are transmitted. If SM2 = 1, then the data on RxD will appear 1 clock period before the falling edge of shift clock on TxD. The clock on TxD then remains low for 2 clock periods, and then goes high again. If SM2 = 0, the data on RxD will appear 3 clock periods before the falling edge of shift clock on TxD. The clock on TxD then remains low for 6 clock periods, and then goes high again. This ensures that at the receiving end the data on RxD line can either be clocked on the rising edge of the shift clock on TxD or latched when the TxD clock is low. The TI flag is set high following the end of transmission of the last bit. The serial port will receive data when REN is 1 and RI is zero. The shift clock (TxD) will be activated and the serial port will latch data on the rising edge of the shift clock. The external device should therefore present data on the falling edge on the shift clock. This process continues till all the 8 bits have been received. The RI flag is set following the last rising edge of the shift clock on TxD. This will stop reception, till the RI is cleared by software. Specifications subject to change without notice contact your sales representatives for the most recent information. 20 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. Serial Port Mode 0: Clock Source Mode Input 1/4 osc/1 1/64 osc/16 1/1024 osc/256 1/12 SM2 0 1 1/4 TX CLOCK Internal Data Bus Write to SBUF PARIN LOAD CLOCK Transmit Shift Register TX START TX SHIFT TI SOUT SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded RxD P3.0 Alternate Input function Serial Port Interrupt RI TxD P3.1 Alternate Input function Serial Control SHIFT CLOCK RX CLOCK LOAD SBUF /RI RX START REN RxD P3.0 Alternate Input function CLOCK PAROUT SIN Receive Shift Register RX SHIFT READ SBUF SBUF SBUF Internal Data Bus Mode 1 In mode 1, the full duplex asynchronous mode is used. Serial communication frames are made up of 10 bits transmitted on TxD and received on RxD. The 10 bits consist of a start bit (0), 8 data bits (LSB first), and a stop bit (1). On receive; the stop bit goes into RB8 in the SFR SCON. The baud rate in this mode is variable. The serial baud can be programmed to be 1/16 or 1/32 of the Timer 1 overflow. Since the Timer 1 can be set to different reload values, a wide variation in baud rates is possible. Transmission begins with a write to SBUF. The serial data is brought out on to TxD pin following the first rollover of divide by 16 counter. The next bit is placed on TxD pin following the next rollover of the divide by 16 counter. Thus the transmission is synchronized to the divide by 16 counter and not directly to the write to SBUF signal. After all 8 bits of data are transmitted the stop bit is transmitted. The TI flag is set after the stop bit has been put out on TxD pin. This will be at the 10th rollover of the divide by 16 counter after a write to SBUF. Reception is enabled only if REN is high. The serial port actually starts the receiving of serial data, with the detection of the falling edge on the RxD pin; the 1-to-0 detector continuously monitors the RxD line, sampling it at the rate of 16 times the selected baud rate. When a falling edge is detected, the divide by 16 counter is immediately reset. This helps to align the bit boundaries with the rollovers of the divide by 16 counter. The 16 states of the counter effectively divide the bit time into 16 slices. The bit detection is done on a best of three bases. The bit detector samples the RxD pin, at the 8th, 9th and 10th counter states. By using a majority 2 or 3 voting system, the bit value is selected. This is done to improve the noise rejection feature of the serial port. If the first bit detected after the falling edge of RxD pin is not 0, then this indicates an invalid start bit, and the reception is immediately aborted. The serial port again looks for a falling edge in the RxD line. If a valid start bit is detected, then the rest of the bits are also detected and shifted into the SBUF. After shifting in 8 data bits, there is one more shift to do, after which the SBUF and RB8 are loaded and RI is set. However certain conditions must be met before the loading and setting of RI can be done. RI must be 0 and Either SM2 = 0, or the received stop bit = 1. If these conditions are met, then the stop bit goes to RB8; the 8 data bits go into SBUF and RI is set. Otherwise the received frame may be lost. After the middle of the stop bit, the receiver goes back to looking for a 1-to-0 transition on the RxD pin. Specifications subject to change without notice contact your sales representatives for the most recent information. 21 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. Serial Port Mode 1: Timer 1 Overflow 1/2 SMOD= (SMOD 1) 0 TCLK 1 1 1/16 1/16 TX START TX CLOCK TX SHIFT TI Timer 2 Overflow (for Serial Port 0 only) Internal Data Bus STOP PARIN START LOAD CLOCK Transmit Shift Register SOUT SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Write to SBUF RxD P3.0 Alternate Input function Serial Port Interrupt RCLK SAMPLE 1- To-0 Detector RX CLOCK RX START CLOCK PAROUT SIN D8 RB8 SBUF 0 1 Serial Control RI SHIFT CLOCK LOAD SBUF RX SHIFT TxD P3.1 Alternate Input function READ SBUF SBUF Internal Data Bus RxD P3.0 Alternate Input function Bit Detector Receive Shift Register Mode 2 This mode uses a total of 11 bits in asynchronous full-duplex communication. The functional description is shown in the figure below. The frame consists of one start bit (0), 8 data bits (LSB first), a programmable 9th bit (TB8) and a stop bit (0). The 9th bit received is put into RB8. The baud rate is programmable to 1/32 or 1/64 of the oscillator frequency, which is determined by the SMOD bit in PCON SFR. Transmission begins with a write to SBUF. The serial data is brought out on to TxD pin following the first rollover of the divide by 16 counter. Thus the transmission is synchronized to the divide by 16 counter, and not directly to the write to SBUF signal. After all 9 bits of data are transmitted the stop bit is transmitted. The TI flag is set after the stop bit has been put out on TxD pin. This will be at the 11th rollover of the divide by 16 counter after a write to SBUF. Reception is enabled only if REN is high. The serial port actually starts the receiving of serial data, with the detection of a falling edge on the RxD pin. The 1-to-0 detector continuously monitors the RxD line, sampling it at the rate of 16 times the selected baud rate. When a falling edge is detected, the divide by 16 counter is immediately reset. This helps to align the bit boundaries with the rollovers of the divide by 16 counter. The 16 states of the counter effectively divide the bit time into 16 slices. The bit detection is done on a best of three bases. The bit detector samples the RxD pin, at the 8th, 9th and 10th counter states. By using a majority 2 of 3 voting system, the bit value is selected. This is done to improve the noise rejection feature of the serial port. If the first bit detected after the falling edge of RxD pin, is not 0, then this indicates an invalid start bit, and the reception is immediately aborted. The serial port again looks for a falling edge in the RxD line. If a valid start bit is detected, then the rest of the bits are also detected and shifted into the SBUF. After shifting in 9 data bits, there is one more shift to do, after which the SBUF and RB8 are loaded and RI is set. However certain conditions must be met before the loading and setting of RI can be done. RI must be 0 and Either SM2 = 0, or the received 9th bit = 1. If these conditions are met, then the 9th bit goes to RB8, the 8 data bits go into SBUF and RI is set. Otherwise the received frame may be lost. After the middle of the stop bit, the receiver goes back to looking for a 1-to-0 transition on the RxD pin. Specifications subject to change without notice contact your sales representatives for the most recent information. 22 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. Serial Port Mode 2: Clock Source Mode Input 1/4 osc/2 1/64 osc/32 1/1024 osc/512 1/2 SMOD= (SMOD 1) 0 1 1/16 1/16 Write to SBUF TX START TX CLOCK TX SHIFT TI RI TB8 Internal Data Bus D8 STOP PARIN START LOAD CLOCK Transmit Shift Register SOUT SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded RxD P3.0 Alternate Input function Serial Port Interrupt TxD P3.1 Alternate Input function READ SBUF SBUF CLOCK PAROUT SIN D8 RB8 SBUF Internal Data Bus Serial Control SHIFT CLOCK SAMPLE RX CLOCK 1- To-0 Detector RX START LOAD SBUF RX SHIFT RxD P3.0 Alternate Input function Bit Detector Receive Shift Register Mode 3 This mode is similar to Mode 2 in all respects; expect that the baud rate is programmable. The user must first initialize the Serial related SFR SCON before any communication can take place. This involves selection of the Mode and Baud rate. The Timer 1 should also be initialized if modes 1 and 3 are used. In all four modes, transmission is started by any instruction that uses SBUF as a destination register. Reception is initiated in Mode 0 by the condition RI = 0 and REN = 0. This will generate a clock on the TxD pin and shift in 8 bits on the RxD pin. Reception is initiated in the other modes by the incoming start bit if REN = 1. The external device will start the communication by transmitting the start bit. Pulse Width Modulation (PWM) The PWM output pins are P1.4 and P1.5. The PWM clock is {Fosc/ (2xDivider)}, the PWM output frequency is {(PWM clock)/32} at 5 bits resolution and {(PWM clock)/256} at 8 bits resolution. The PWM SFR is shown as below: PWMC ($D3H and $D4H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 PBS Bit1 PFS1 Bit0 PFS0 PBS: when set, the PWM is 5 bits resolution. PFS [1:0]: The PWM clock divider select. PFS1 0 0 1 1 PFS0 0 1 0 1 PWM clock divider select 1 2 4 8 Specifications subject to change without notice contact your sales representatives for the most recent information. 23 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. PWMD ($B3H and $B4H) Bit7 PWMD.7 Bit6 PWMD.6 Bit5 PWMD.5 Bit4 PWMD.4 Bit3 PWMD.3 Bit2 PWMD.2 SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Bit1 PWMD.1 Bit0 PWMD.0 Real Time Clock (RTC) The on-chip RTC keeps time of second and minute functions. Its time base is a 32.768 KHz crystal between pins X32OUT (alternate function of ALE) and X32IN (alternate function of PSEN). The RTC maintains time to a second. It also allows a user to read or write values of seconds and minute. The RTC function used SFR descriptor as below: RTCS ($A1H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 RTCen Stable SEC.5 SEC.4 SEC.3 SEC.2 SEC.1 SEC.0 RTCen: When set to ‘1’, enable the enable RTC function. When this bit set, the ALE and PSEN pins output will disable, and the ALE and PSEN pins will use for RTC function as X32OUT and X32IN. Stable: Read only. The Stable bit will set to 1 when the RTC module stable. Please wait 2 seconds before used the RTC function. SEC [5:0]: show the current second counter at RTC function. The range is from 00H to 3BH. RTCC ($A2H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 INT_SEL1 INT_SEL0 MIN.5 MIN.4 MIN.3 MIN.2 MIN.1 INT_SEL [1:0]: the interrupt distribution selection bit, the interrupt vector is 43H. 00: the interrupt is set as 0.5 second 01: the interrupt is set as 1 second 10: the interrupt is set as 30 second 11: the interrupt is set as 60 second MIN [5:0]: show the current minute counter at RTC function. The range is from 00H to 3BH. Bit0 MIN.0 Starting and stopping the RTC: RTCS ($A1H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 RTCen Stable SEC.5 SEC.4 SEC.3 SEC.2 SEC.1 SEC.0 The RTC Function is enable by set the RTCS.7 (RTCen=1), then the ALE and /PSEN pins will switch to X32OUT and X32IN that for RTC function used, the ALE and PSEN signal output will disable; the crystal frequency is 32768Hz. See figure 17. R SW 1 1 2 J1 1 X 3 2 in ( /P S E N ) Y1 32768Hz J2 1 X 3 2 o u t(A L E ) 1 2 RTCen 3 2 7 6 8 H z C lo c k in I n C h ip Figure 17 The RTC Crystal connect diagram The stable bit (RTCS.6) will set to 1 when the RTC module stable. The design is about 31.25msec; suggest waiting 2 Specifications subject to change without notice contact your sales representatives for the most recent information. 24 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded second to use the RTC function. This bit will clear when RTCen bit set again. The SEC [5:0] will show the second counter (range from 00H to 3BH), and the MIN [5:0] will show the minute counter (range from 00H to 3BH) of RTC function. This two register will clear when RTCen bit set. Interrupt: The RTC can select each of 4 interrupt sources: 0.5 second, 1 second, 0.5 minute, and 1 minute. The interrupt vector is 43H, it’s can wake-up CPU from POWER-DOWN mode. The Interrupt functions are test at each test item. Like the int0 to int5 are test in PDWU function, the RTC interrupt are test at RTC function test, the ADC interrupt are test at ADC function test. This test item is focus in the priority test and only checks the lower voltage by each crystal. The interrupt SFRs show as below: IE1 ($A9H) Bit3 Bit2 Bit1 Bit0 EADC ERTC ERTC: When set to ‘1’, enable the RTC interrupt. If you want to use the RTC interrupt function, must enable the EA bit in IE.7 and enable the ERTC bit in IE1.2. EADC: When set to ‘1’, enable the ADC interrupt. If you want to use the ADC interrupt function, must enable the EA bit in IE.7 and enable the EADC bit in IE1.3 Bit7 Bit6 Bit5 Bit4 RTCC ($A2H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 INT_SEL1 INT_SEL0 MIN.5 MIN.4 MIN.3 MIN.2 MIN.1 MIN.0 Then select the interrupt distribution in INT_SEL [1:0] in RTCC [7:6]. The RTC can select each of 4 interrupt sources: 0.5 second, 1 second, 0.5 minute, and 1 minute. The interrupt vector is 43H, it can wake-up CPU from POWER-DOWN mode. IFR ($AAH) Bit3 Bit2 Bit1 Bit0 ADCIF RTCIF ADCIF: When interrupt occupy the ADC interrupt flag (IFR.3) will set, and the CPU will execute the interrupt subroutine at the interrupt vector 4BH. The ADC Interrupt Flag must clear by software. RTCIF: When interrupt occupy the RTC interrupt flag (IFR.2) will set, and the CPU will execute the interrupt subroutine at the interrupt vector 43H. The RTC Interrupt Flag must clear by software. Bit7 Bit6 Bit5 Bit4 IP1 ($B9H) Bit7 Bit6 Bit5 Bit4 Bit3 PADC Bit2 PRTC Bit1 Bit0 The interrupt priority can be set at IP1.2 or IP1.3. PADC: When set to ‘1’, enable the ADC interrupt priority. PRTC: When set to ‘1’, enable the RTC interrupt priority. Specifications subject to change without notice contact your sales representatives for the most recent information. 25 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. U2 int 0.5sec int 1sec Divider 16384 Divider 2 Divider 30 4 3 2 1 15 14 13 12 11 10 9 7 D0 D1 D2 D3 D4 D5 D6 D7 A B C G SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Y Y 5 6 int out int 0.5min Divider 2 int 1min 32768Hz Clock in int sel0 int sel1 RTCen 74151 5 bits shif register sec0 sec1 sec2 second register sec3 sec4 sec5 5 bits shif register min0 min1 min2 minute register min3 min4 min5 Figure 18 The RTC Block Diagram LED Driving Capability Control This function is set the sink current more then 10mA for each pin, 26mA for whole Port 0, 15mA for whole Port 1 or whole Port2 or whole Port3 or whole Port4, and total 71mA for whole chip. The SFR shown as below: Port Name Port0 Port1 Port2 Port3 Port4 SFR Address $92H $93H $94H $95H $96H Iol(max) of pre port 26 mA 15 mA 15 mA 15 mA 15 mA Power Saving Mode The SM89T16R1 has several features that help the user to control the power consumption of the device. The powers saving features are basically the Power Down mode, Economy mode and the Idle mode of operation. Idle Mode The user can put the device into idle mode by writing 1 to the bit PCON.0. The instruction that sets the idle bit is the last instruction that will be executed before the device goes into Idle Mode. In the Idle Mode, the clock to the CPU is halted, but not to the Interrupt, Timer and Serial port blocks. This forces the CPU state to be frozen; the Program counter, the Stack Pointer, the Program Status Word, the Accumulator and the other registers hold their contents. The ALE and PSEN pins are held high during the idle state. The port pins hold the logical states they had at the time idle was activated. The idle mode can be terminated in two ways. Since the interrupt controller is still active, the activation of any enabled interrupt can wake up the processor. This will automatically clear the idle bit, terminate the idle mode, and the Interrupt Service Routine (ISR) will be executed. After the ISR, execution of the program will continue from the instruction that put the device into idle mode. The Idle mode can also be exited by activating the reset. The device can be put into reset either applying a high on the external RST pin or a Power on reset condition. The external reset pin has to be held high for at least two machine cycles to be recognized as a valid reset. In the reset condition the program counter is reset to 0000H and all the SFRs are set to the reset condition. Since the clock is already running there is no delay and execution start immediately. When the SM89T16R1 is exiting from an idle mode with a reset, the instruction following the one that put the device into idle mode is not executed. So there is no danger of unexpected writes. Specifications subject to change without notice contact your sales representatives for the most recent information. 26 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded The Power Down Wake Up (PDWU) function The device can be put into Power Down mode by writing 1 to bit PCON.1. The instruction that does this will be the last instruction to be executed before the device goes into Power Down mode. In the Power Down mode, all the clocks are stopped and the device comes to a halt. All activity is completely stopped and the power consumption is reduced to the lowest possible value. In this state the ALE and PSEN pins are pulled low. The port pins output the values held by their respective SFRs. The SM89T16R1 will exit the Power Down mode with a reset or by a RTC (Real Time Clock) interrupt or by an external interrupts pin enabled as level detects. 1. An external reset can be used to exit the Power Down state. The high on RST pin terminates the Power Down mode, and restarts the clock. The program execution will restart from 0000H. 2. An external interrupt pin and RTC interrupt can be used to exit the Power Down state when the external interrupt or RTC interrupt actives and provided the corresponding interrupt is enabled, while the global enable (EA) bit is set and the external input has been set to a level detect mode or RTC interrupt set. If these conditions are met, then the low level on the external pin or RTC interrupt re-starts the oscillator. Then device executes the interrupt service routine for the corresponding external interrupt or RTC interrupt. After the interrupt service routine is completed, the program execution returns to the instruction after the one that put the device into Power Down mode and continues from there. The status of external pins during Idle and Power Down: Mode Idle Idle Power Down Power Down Program Memory Internal External Internal External ALE 1 1 0 0 /PSEN 1 1 0 0 PORT0 Data Float Data Float PORT1 Data Data Data Data PORT2 Data Address Data Data PORT3 Data Data Data Data PORT4 Data Data Data Data PCON ($87H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 SMOD SMOD0 SMOD: This bit set to ‘1’ to make the UART baud-rate double. SMOD0: This bit define the SCON.7 and SCON1.7 use as FE (FE1) or SM0 (SM0_1) PD: When set to ‘1’, the MCU will into Power Down mode IDLE: When set to ‘1’, the MCU will into IDLE mode Bit1 PD Bit0 IDLE IE ($A8H) Bit7 Bit6 Bit5 Bit4 EA ES1 ET2 ES0 EA: When set to ‘1’, enable interrupt global. ES1: When set to ‘1’, enable UART1 interrupt. ET2: When set to ‘1’, enable Timer2 interrupt. ES0: When set to ‘1’, enable UART interrupt. ET1: When set to ‘1’, enable Timer1 interrupt. EX1: When set to ‘1’, enable external interrupt 1. ET0: When set to ‘1’, enable Timer0 interrupt. EX0: When set to ‘1’, enable external interrupt 0. Bit3 ET1 Bit2 EX1 Bit1 ET0 Bit0 EX0 IP ($B8H) Bit7 Bit6 Bit5 PT2 Bit4 PS0 Bit3 PT1 Bit2 PX1 Bit1 PT0 Bit0 PX0 PT2: Timer2 interrupt priority. PS0: UART interrupts priority. Specifications subject to change without notice contact your sales representatives for the most recent information. 27 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. PT1: Timer1 interrupt priority. PX1: external interrupt 1 priority. PT0: Timer0 interrupt priority. PX0: external interrupt 0 priority. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded EIP ($BAH) Bit7 Bit6 Bit5 Bit4 Bit3 PX5 Bit2 PX4 Bit1 PX3 Bit0 PX2 PX5: When set to ‘1’, external interrupt 5 priorities. PX4: When set to ‘1’, external interrupt 4 priorities. PX3: When set to ‘1’, external interrupt 3 priorities. PX2: When set to ‘1’, external interrupt 2 priorities. EIE ($ABH) Bit7 Bit6 Bit5 Bit4 Bit3 EX5 Bit2 EX4 Bit1 EX3 Bit0 EX2 EX5: When set to ‘1’, enable external interrupt 5. EX4: When set to ‘1’, enable external interrupt 4. EX3: When set to ‘1’, enable external interrupt 3. EX2: When set to ‘1’, enable external interrupt 2. TCON ($88H) Bit7 Bit6 Bit5 TF1 TR1 TF0 TF1: Timer 1 overflow flag. TR1: Timer 1 run control bit. TF0: Timer 0 overflow flag. TR0: Timer 0 run control bit. IE1: External Interrupt 1 edge flag. IT1: Interrupt 1 type control bit. IE0: External Interrupt 0 edge flag. IT0: Interrupt 0 type control bit. Bit4 TR0 Bit3 IE1 Bit2 IT1 Bit1 IE0 Bit0 IT0 CKCON ($8EH) Bit5 Bit4 Bit3 Bit2 Bit1 T2M T1M T0M MD2 MD1 T2M: Timer 2 clock select. When “1” used divide by 4 clock; when “0” used divide by 12 clock. T1M: Timer 1 clock select. When “1” used divide by 4 clock; when “0” used divide by 12 clock. T0M: Timer 0 clock select. When “1” used divide by 4 clock; when “0” used divide by 12 clock. MD [2:0]: Stretch MOVX selects bits MD2 0 0 0 0 1 1 1 1 MD1 0 0 1 1 0 0 1 1 MD0 0 1 0 1 0 1 0 1 Stretch Value 0 1 2 3 4 5 6 7 MOVX duration 2 machine cycles 3 machine cycles (Default) 4 machine cycles 5 machine cycles 6 machine cycles 7 machine cycles 8 machine cycles 9 machine cycles Bit7 Bit6 Bit0 MD0 Specifications subject to change without notice contact your sales representatives for the most recent information. 28 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Dual DPTR Function The DPS.0 define the instruction of INC DPTR AND DEC DPTR are working in DPTR0 or DPTR1. DPS ($A6H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 DPS DPS = 1 the instruction of INC DPTR and DEC DPTR are working in DPTR1. = 0 the instruction of INC DPTR and DEC DPTR are working in DPTR0. DPH ($83H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 DPL ($82H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 DPH1 ($A5H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 DPL1 ($A4H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Data SRAM The SCONF.1 must set to ‘1’ to enable the Expand 1024 bytes RAM, and this Expand RAM area must read/write by using the MOVX instruction. SCONF ($BFH) Bit7 Bit6 Bit5 Bit4 Bit3 SMOD_1 PDWUE SMOD_1: This bit set to ‘1’ to make the serial port 1 baud-rate double. PDWUE: When set to ‘1’, enable the PDWU function. OME: When set to ‘1’, enable the 1024 bytes expanded RAM. ALEI: When set to ‘1’, it will stop ALE clock output for EMI reduce. Bit2 Bit1 OME Bit0 ALEI Power Management Mode (PMM) Power Management Mode offers a complete scheme of reduced internal clock speeds that allow the CPU to run software but to use substantially less power. Normally, during default operation, the SM89T16R1 uses 4 clocks per machine cycle. Thus the instruction cycle (machine cycle clock) rate is clock/4. At 16 MHz crystal speed, the instruction cycle speed is 4 MHz. In Power Management Mode (PMM) the instruction cycle (machine cycle clock) rate is clock/1024. At same 16 MHz crystal speed, the instruction cycle speed is 15.6 KHz. The operation current is down from 20mA to 5mA. See Table 5. Crystal Speed 11.0592 MHz 16 MHz 25 MHz Table 5 Full Operation (4 clocks/machine cycle) Instruction rate/operation current 2.765 MHz/19.6 mA 4.0 MHz/20 mA 6.25 MHz/30 mA PMM (1024 clocks/machine cycle) Instruction rate/operation current 10.8 KHz/4.78 mA 15.6 kHZ/5 mA 24.4 kHz/5.6 mA Specifications subject to change without notice contact your sales representatives for the most recent information. 29 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Economy Mode The power consumption of microcontroller relates to operating frequency. The SM89T16R1 offers an Economy mode to reduce the internal clock rate dynamically without external components. By default, one machine cycle needs 4 clocks. In Economy mode, software can select 4, 64, or 1024 clocks per machine cycle. It keeps the CPU operating a acceptable speed but eliminates the power consumption. In the Idle mode, the clock of the core logic is stopped, but all clocked peripherals such as timer are still running at a rate of clock/4. In the Economy mode, all clocks peripherals run at the same reduced clocks rate as in core logic. So the Economy mode may provide lower power consumption than Idle mode. Software invokes the Economy mode by setting the appropriate bits in the SFRs. Setting the bits CD0 (PMR.6), CD1 (PMR.7) decides the instruction cycle rate as below: PMR ($D1H) Bit7 CD1 Bit6 CD0 Bit5 Bit4 Bit3 XTOFF Bit2 Bit1 Bit0 CD1 0 0 1 1 CD0 0 1 0 1 Clocks/machine cycle Reserved 4 64 1024 Change Clock Test Internal RC oscillator and External crystal switching EXIF ($91H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 IE5 IE4 IE3 IE2 XT/~RG IE5: When set to ‘1’, external interrupt 5 flag. IE4: When set to ‘1’, external interrupt 4 flag. IE3: When set to ‘1’, external interrupt 3 flag. IE2: When set to ‘1’, external interrupt 2 flag. XT/~RG: When set to ‘1’, the MCU used External Crystal. When clear to ‘0’, the MCU used Internal RC Oscillator This selection of instruction rate is going to take effect after a delay of one instruction cycle. Switching to divide by 64 or 1024 mode must first go from divide by 4 modes. This means software cannot switch directly between clock/64 and clock/1024 mode. The CPU has to return clock/4 mode first, then go to clock/64 or clock/1024 mode. The SM89T16R1 allows the user to use internal RC oscillator instead of external crystal. Setting the XT/~RG bit (EXIF.3) selects the crystal or RC oscillator as the clock source. When invoking RC oscillator in Economy mode, software may set the XTOFF bit to turn off the crystal amplifier for saving power. The CPU would run at the clock rate of approximately 2-4 MHz divided by 4, 64 or 1024. The RC oscillator is not precise so that cannot be invoked to the operation that needs the accurate time-base such as serial communication. If crystal amplifier is disabled and RC oscillator is present clock source, software must first clear the XTOFF bit to turn on crystal amplifier before switch to crystal operation. PMR ($D1H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 CD1 CD0 XTOFF XTOFF: External Crystal off; if the XT/~RG bit set to 1, this bit (XTOFF) don’t care. Bit1 Bit0 Specifications subject to change without notice contact your sales representatives for the most recent information. 30 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded Internal Clock Source XT/~RG XTOFF 0 0 1 1 0 1 0 1 Internal RC Oscillator Internal RC Oscillator(Ext-Crystal OFF) External Crystal External Crystal The Priority structure and vector locations of interrupts: Source External interrupt 0 Timer 0 overflow External interrupt 1 Timer 1 overflow UART interrupt Timer 2 overflow UART 1 interrupt RTC interrupt ADC interrupt External interrupt 2 External interrupt 3 External interrupt 4 External interrupt 5 Flag IE0 TF0 IE1 TF1 RI+TI TF2+EXF2 RI_1+TI_1 RTCIF ADCIF IE2 IE3 IE4 IE5 Priority level 1(highest) 2 3 4 5 6 7 8 9 10 11 12 13(lowest) Vector Address 03H 0BH 13H 1BH 23H 2BH 33H 43H 4BH 5BH 63H 6BH 73H T2MOD ($C9H) Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 HC5 HC4 HC3 HC2 T2CR T2OE DCEN HC5: Hardware Clear /INT5 flag HC4: Hardware Clear /INT4 flag HC3: Hardware Clear /INT3 flag HC2: Hardware Clear /INT2 flag T2CR: Timer 2 Capture Reset. In the Timer2 Capture Mode this bit enables/disables hardware automatically reset Timer2 while the value in TL2 and TH2 have been transferred into the capture register. T2OE: Timer2 clock Output Enable bit. If set to 1, the Timer2 clock will output to P1.0. DCEN: Down Count Enable. When set this bit then allows Timer2 to be configured as an up/down counter. Application Reference X'tal C1 C2 R 3MHz 30 pF 30 pF open Valid for SM89T16R1 6MHz 9MHz 30 pF 30 pF 30 pF 30 pF open open 12MHz 22 pF 22 pF open XI X'tal SM89T16R1 R X'tal 16MHz 25MHz C1 C2 C1 30 pF 15 pF C2 30 pF 15 pF R open open Note: Oscillation circuit may differs with different crystal or ceramic resonator in higher oscillation frequency which was due to each crystal or ceramic resonator has its own characteristics. User should check with the crystal or ceramic resonator manufacturer for appropriate value of external components. X2 Specifications subject to change without notice contact your sales representatives for the most recent information. 31 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded PDIP 40L (600mil) Package Information： Symbol A1 A2 b b1 b2 b3 c c1 D E E1 e eB L S Q1 θ Dimension in mm Min 0.254 3.683 0.356 0.356 1.016 1.016 0.203 0.203 52.07 14.99 13.69 － Dimension in MIL Min 10 145 14 14 40 40 8 8 2050 590 539 － Nom － Max － Nom － Max － 3.810 0.500 0.457 1.270 1.321 0.254 0.254 52.2 15.24 13.87 2.540 16.26 3.302 1.981 1.778 － 3.937 0.660 0.508 1.524 1.626 0.432 0.356 52.32 15.49 13.94 － 150 20 18 50 52 10 10 2055 600 546 100 640 130 78 70 － 155 26 22 60 64 17 14 2060 610 549 － Note: 1. Refer to JEDEC STD.MS-011(AC). 2. Dimension D and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. D and E1 are maximum plastic body size dimension include mold mismatch. 3. Dimension b3 does not include dambar protrusion. Allowable dambar protrusion shall not cause the lead width to exceed the maximum b3 dimension by more than 0.2mm. 15.75 2.921 1.727 1.651 0° 16.76 3.683 2.235 1.905 10° 620 115 68 65 0° 660 145 88 75 10° Specifications subject to change without notice contact your sales representatives for the most recent information. 32 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded PLCC 44L Package Information： UNIT SYMBOL A A1 A2 B B1 c D D1 D2 E E1 E2 e y θ INCH(REF) 0.180(MAX) 0.024 ±0.005 0.105 ±0.005 0.018 + 0.004 - 0.002 0.028 + 0.004 - 0.002 0.010(TYP) 0.690 ±0.010 0.653 ±0.003 0.610 ±0.020 0.690 ±0.010 0.653 ±0.003 0.610 ±0.010 0.050(TYP) 0.003(MAX) 0~5° MM(BASE) 4.572(MAX) 0.52 ±0.14 2.667 ±0.127 0.457 + 0.102 - 0.051 0.711 + 0.102 - 0.051 0.254(TYP) 17.526 ±0.254 16.586 ±0.076 15.494 ±0.508 17.526 ±0.254 16.586 ±0.076 15.494 ±0.254 1.270(TYP) 0.076(MAX) 0~5° Specifications subject to change without notice contact your sales representatives for the most recent information. 33 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded QFP 44L(10x10x2.0mm) Package Information： Symbol A A1 A2 b b1 c Note: 1. Refer to JEDC STD.MS-022(AB). 2. Dimension E1 do not include mold protrusion. Allowable protrusion is 0.25mm per side.E1 are maximum plastic body size dimension include mold mismatch . 3. Dimension b does not include dambar protrusion .Allowable dambar protrusion shall not cause the lead width to exceed the maximum b3 dimension by more than 0.1 mm. Dimension in mm Min － Dimension in MIL Min － Nom － Max 2.45 0.25 2.10 0.45 0.41 0.23 0.19 13.40 10.10 － Nom － Max 964 9.6 82.7 17.7 16.1 9.1 7.5 528 398 － 0.05 1.90 0.29 0.29 0.11 0.11 13.00 9.90 － 0.15 2.00 0.32 0.30 0.17 0.15 13.20 10.00 0.800 0.88 1.60 － － 2.1 74.8 11.4 11.4 4.3 4.3 512 390 － 6.0 78.7 12.6 11.8 6.7 5.9 520 394 31.5 34.6 63.0 － － c1 E E1 【e】 L L1 y θ 0.73 1.50 － 1.03 1.70 0.076 7° 28.7 59.1 － 40.6 66.9 3 7° 0° 0° Specifications subject to change without notice contact your sales representatives for the most recent information. 34 Ver 2.1 SM89T16R1 08/2006 SyncMOS Technologies International, Inc. SM89T16R1 8-Bits Micro-controller With 64KB Flash ROM & 1KB RAM & Two UART & RTC & ADC & PWM embedded e MCU writer list Company Advantech 7F, No.98, Ming-Chung Rd., Shin-Tien City, Taipei, Taiwan, ROC Web site: http://www.aec.com.tw Hi-Lo 4F, No. 20, 22, LN, 76, Rui Guang Rd., Nei Hu, Taipei, Taiwan, ROC. Web site: http://www.hilosystems.com.tw Leap 6th F1-4, Lane 609, Chunghsin Rd., Sec. 5, Sanchung, Taipei Hsien, Taiwan, ROC Web site: http://www.leap.com.tw Xeltek Electronic Co., Ltd 338 Hongwu Road, Nanjing, China 210002 Web site: http://www.xeltek-cn.com Contact info Tel:02-22182325 Fax:02-22182435 E-mail: aecwebmaster@advantech.com.tw Programmer Model Number Lab Tool - 48XP (1 * 1) Lab Tool - 848 (1*8) Tel:02-87923301 Fax:02-87923285 E-mail: support@hilosystems.com.tw All - 11 (1*1) Gang - 08 (1*8) Tel:02-29991860 Fax:02-29990015 E-mail: service@leap.com.tw Leap-48 (1*1) SU - 2000 (1*8) Tel:+86-25-84408399, 84543153-206 E-mail: xelclw@jlonline.com, xelgbw@jlonline.com Superpro/2000 (1*1) Superpro/280U (1*1) Superpro/L+(1*1) Specifications subject to change without notice contact your sales representatives for the most recent information. 35 Ver 2.1 SM89T16R1 08/2006