NQ15W50SGA30PSG-G

Technical Specification NQ15W50SGA30 6.0-15.0V Input 0.8-5.0V Outputs 30 Amp Current Non Isolated SMT Surface Mount The NiQor® SMT DC/DC converter is a non-isolated buck regulator, which employs synchronous rectification to achieve extremely high conversion efficiency. The NiQor family of converters are used predominately in DPA systems using a front end DC/DC high power brick (48Vin to low voltage bus). The non-isolated NiQor converters are then used at the point of load to create the low voltage outputs required by the design. The wide trim module can be programmed to a variety of output voltages through the use of a single external resistor. RoHS compliant see last page. Operational Features • Ultra high efficiency, up to 93% at full rated load • Delivers up to 30 Amps of output current with minimal derating - no heatsink required • Input Voltage Range : 6.0 - 15.0V • Fast transient response time • On-board input and output filter capacitor • No minimum load requirement means no preload resistors required Non-Isolated NiQor surface mount module Protection Features • Input under-voltage lockout disables converter at low input voltage conditions • Temperature compensated over-current shutdown protects converter from excessive load current or short circuits • Output over-voltage protection protects load from damaging voltages • Thermal shutdown protects converter from abnormal environmental conditions Mechanical Features • DOSA standard SMT pin-out configuration • Industry standard size: 1.3” x 0.53” x 0.32” (33 x 13.5 x 8.12 mm) • Total weight: 0.18 oz. (5 grams), lower mass greatly reduces vibration and shock problems • Open frame construction maximizes air flow cooling • Also available in SIP packaging Safety Features • UL/cUL 60950-1 recognized (US & Canada) • TUV certified to EN60950-1 • Meets 72/23/EEC and 93/68/EEC directives which facilitates CE Marking in user’s end product • Board and plastic components meet UL94V-0 flammability requirements Control Features • On/Off control • Output voltage trim (industry standard) permits custom voltages and voltage margining • Remote Sense (standard option) • Active Current Sharing for Parallel Applications Product # NQ15W50SGA30 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2NS163E Rev. C 10/03/08 Page 1 Technical Specification MECHANICAL DIAGRAM Surface Mount Package 1.30 0.063 (1,6) Input: Outputs: Current: Package: 6.0 - 15.0V 0.8 - 5.0V 30A SMT Typ. (33,0) 0.320+.006 0.100 (2,54) (8,12+0,15) See Note 4 0.089 (2,26) 3 9 2 4 0.080 x 0.063” (2.0 x 1,6) 5 6 7 8 0.120 0.53 (13,5) 10 (3,05) 0.407 (10,33) 0.075 (1,91) 1 0.048 0.107 0.297 0.487 0.677 0.867 1.057 (26,85) (22,02) (17,20) (12,37) (7,54) (2,72) (1,22) 0.063 (1,6) 0.025 (0,64) 0.014+.009 (0,36+0,22) Bottomside Clearance Side View 1.196 (30,38) 1.177 (29,90) Bottom View Recommended SMT Pad Size: Minimum: 0.074” x 0.122” (1.88mm x 3.1mm) Maximum: 0.095” x 0.140” (2.41mm x 3.56mm) NOTES 1) SMT Contacts: Material - Brass Finish - Gold over Nickel plate 2) Undimensioned components are shown for visual reference only. 3) All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) x.xxx +/-0.010 in. (x.xx +/-0.25mm) 4) Coplanarity for pins 1-10 is 0.004” max 5) Weight: 0.18 oz. (5 g) typical 6) Workmanship: Meets or exceeds IPC-A-610C Class II SMT CONTACT DESIGNATIONS Pin No. Name Function 1 2 3 4 5 6 7 8 9 10 ON/OFF Vin(+) N/C GND Vout(+) TRIM SENSE(+) IShare GND GND Input to turn converter on/off Positive input voltage No Connection Ground Positive output voltage Output Voltage Trim Positive remote sense Current share Ground Ground Pins in Italics Shaded text are Optional Product # NQ15W50SGA30 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2NS163E Rev. C 10/03/08 Page 2 Technical Specification Input: Outputs: Current: Package: 6.0 - 15.0V 0.8 - 5.0V 30A SMT ELECTRICAL CHARACTERISTICS - NQ15W50SGA30 Series Parameter ABSOLUTE MAXIMUM RATINGS Input Voltage Non-Operating Operating Operating Temperature Storage Temperature Voltage at ON/OFF input pin RECOMMENDED OPERATING CONDITIONS Input Voltage Range Input Fuse Rating External Input Capacitance Output Voltage Output Current INPUT CHARACTERISTICS Input Under-Voltage Lockout Turn-On Voltage Threshold Turn-Off Voltage Threshold Lockout Hysteresis Maximum Input Current “ “ No-Load Input Current “ “ Disabled Input Current Inrush Current Transient Rating Input Filter Capacitor Value Input Reflected-Ripple Current “ “ OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Range Operating Output Current Range Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise (pk-pk\RMS) “ “ Output DC Over Current Shutdown External Output Capacitance DYNAMIC CHARACTERISTICS Input Voltage Ripple Rejection Output Voltage during Current Transient For a Step Change in Output Current (0.1A/µs) For a Step Change in Output Current (3A/µs) Settling Time Turn on Transient Inhibit Time Rise Time Output Voltage Overshoot EFFICIENCY 100% Load “ “ 50% Load “ “ TA=25°C, airflow rate=300 LFM, Vin=12Vdc unless otherwise noted; full operating temperature range is -40°C to +105°C ambient temperature with appropriate power derating. Specifications subject to change without notice. Module All All All All All All All All All All All All All 1.8V 3.3V 5.0V 1.8V 3.3V 5.0V All All All 1.0V 2.5V 5.0V 0.8V All All All All All All 1.0V 2.5V 5.0V All All All All All All All All All 1.8V 3.3V 5.0V 1.8V 3.3V 5.0V Min. 0 -40 -55 -3 6 100 0.8 0 5.20 4.60 0.790 0.8 0 33 100 2 4 Typ. 5.60 5.00 0.6 102 156 232 3 20 36 68 98 0.800 27\5.0 43\11.6 67\20.4 40 50 250 250 100 85.0 90.0 93.0 86.0 91.0 93.0 Max. 16 15 105 125 15 15 40 5.0 30 6.00 5.40 6.0 18.0 28.0 0.1 0.810 5.5 30 0.5 0.6 1 3 47 10,000 4 8 0 Units V V °C °C V V A µF V A V V V A A A mA mA mA mA A2s µF mA mA mA V V A % % % % mV mV mV A µF dB mV mV µs ms ms V % % % % % % Notes & Conditions Continuous Continuous Fast blow external fuse recommended ESR1mW 120Hz 50%-75%-50% Iout max; 100uF 50%-75%-50% Iout max; 470uF To within 1.5% Vout nom. Resistive load “ “ Product # NQ15W50SGA30 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2NS163E Rev. C 10/03/08 Page 3 Technical Specification Parameter Module All All All All All All All All All All All All All All All All All All Input: Outputs: Current: Package: 6.0 - 15.0V 0.8 - 5.0V 30A SMT ELECTRICAL CHARACTERISTICS (continued) - NQ15W50SGA30 Series TEMP LIMITS FOR POWER DERATING Semiconductor Junction Temperature Board Temperature FEATURE CHARACTERISTICS Switching Frequency ON/OFF Control Negative Logic (N) ON/OFF Control Off-State Voltage On-State Voltage Pull-Up Voltage Pull-Up Resistance Positive Logic (P) ON/OFF Control Logic Low Voltage Range Logic High Voltage Range (internal pullup) Logic Low Sink Current Logic High Sink Current (leakage) Output Voltage Trim Range Output Over-Voltage Protection Over-Temperature Shutdown Over-Temperature Shutdown Restart Hysteresis RELIABILITY CHARACTERISTICS Calculated MTBF (Telcordia) Calculated MTBF (MIL-217) Field Demonstrated MTBF Min. 330 1.5 -3.0 -0.2 2.2 0.75 5.6 Typ. 360 Vin 49.9 0.7 6.0 128 10 14.0 10.8 Max. 125 125 390 6.5 0.6 1.0 10 5.5 6.4 Units °C °C kHz V V V kW V V mA µA V V °C °C Notes & Conditions Package rated to 150°C UL rated max operating temp 130°C Half on small duty cycle (e.g. 16Vin; 0.75Vout) See Figure A Open collector/drain input; see Figure A Vin = 15 V Measured Vout+ to common pins Over full temp range Average PCB Temperature 106 Hrs. TR-NWT-000332; 100% load, 200LFM, 40oC Ta 106 Hrs. MIL-HDBK-217F; 100% load, 200LFM, 40oC Ta 106 Hrs. See our website for details STANDARDS COMPLIANCE Parameter P Notes File # E194341 Certified by TUV Test on entire assembly; board & plastic components UL94V-0 compliant ESD test, 8kV - NP, 15kV air - NP (Normal Performance) Section 7 - electrical safety, Section 9 - bonding/grounding STANDARDS COMPLIANCE UL/cUL 60950-1 EN60950-1 72/23/EEC 93/68/EEC Needle Flame Test (IEC 695-2-2) IEC 61000-4-2 GR-1089-CORE Telcordia (Bellcore) GR-513 • An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or download from the SynQor website. QUALIFICATION TESTING Parameter P # Units 32 5 5 10 5 5 5 15 pins Test Conditions 10-55Hz sweep, 0.060” total excursion,1 min./sweep, 120 sweeps for 3 axis QUALIFICATION TESTING Life Test Vibration Mechanical Shock Temperature Cycling Power/Thermal Cycling Design Marginality Humidity Solderability 95% rated Vin and load, units at derating point, 1000 hours 100g minimum, 2 drops in x and y axis, 1 drop in z axis -40°C to 100°C, unit temp. ramp 15°C/min., 500 cycles Toperating = min to max, Vin = min to max, full load, 100 cycles Tmin-10°C to Tmax+10°C, 5°C steps, Vin = min to max, 0-105% load 85°C, 85% RH, 1000 hours, continuous Vin applied except 5min./day MIL-STD-883, method 2003 • Extensive characterization testing of all SynQor products and manufacturing processes is performed to ensure that we supply robust, reliable product. Contact the factory for official product family qualification documents. Product # NQ15W50SGA30 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2NS163E Rev. C 10/03/08 Page 4 Technical Specification 100 95 10 12 Input: Outputs: Current: Package: 6.0 - 15.0V 0.8 - 5.0V 30A SMT Power Dissipation (W) 90 Efficiency (%) 8 85 80 75 70 65 60 0 3 6 9 12 15 18 21 24 27 30 5.0 Vout 3.3 Vout 1.8 Vout 6 4 5.0 Vout 3.3 Vout 1.8 Vout 0 0 3 6 9 12 15 18 21 24 27 30 2 Load Current (A) Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for nominal input voltage at 25°C. Figure 2: Power dissipation at nominal output voltage vs. load current for nominal input voltage at 25°C. 35 30 25 Iout (A) 20 15 10 5 0 0 25 40 55 70 85 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) Semiconductor junction temperature is within 1°C of surface temperature Ambient Air Temperature (°C) Figure 3: Maximum output power derating curves with nominal output set to 1.8Vo units under various thermal conditions and nominal input voltage (P option, see ordering page). 35 30 25 Figure 4: Thermal plot of the converter with nominal Vout set to 1.8Vo at nominal Vin and 21.2 amp load current mounted on a 55°C, 200 LFM, 6-Layer, 2 oz. copper board (typical installation). Iout (A) 20 15 10 5 0 0 25 40 55 70 85 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) Semiconductor junction temperature is within 1°C of surface temperature Ambient Air Temperature (°C) Figure 5: Maximum output power derating curves with nominal output set to 3.3Vo units under various thermal conditions and nominal input voltage (P option, see ordering page). Product # NQ15W50SGA30 Phone 1-888-567-9596 Figure 6: Thermal plot of the converter with nominal Vout set to 3.3Vo at nominal Vin and 18.4 amp load current mounted on a 55°C, 200 LFM, 6-Layer, 2 oz. copper board (typical installation). Doc.# 005-2NS163E Rev. C 10/03/08 Page 5 www.synqor.com Technical Specification 30 Input: Outputs: Current: Package: 6.0 - 15.0V 0.8 - 5.0V 30A SMT 25 20 Iout (A) 15 10 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 5 0 0 25 40 55 70 85 Semiconductor junction temperature is within 1°C of surface temperature Ambient Air Temperature (°C) Figure 7: Maximum output power derating curves with nominal output set to 5.0Vo units under various thermal conditions and nominal input voltage (P option, see ordering page). Figure 8: Thermal plot of the converter with nominal Vout set to 5.0Vo at nominal Vin and 16.1 amp load current mounted on a 55°C, 200 LFM, 6-Layer, 2 oz. copper board (typical installation). 5.0Vout 5.0Vout 3.3Vout 3.3Vout 1.8Vout 1.8Vout 0.8Vout 0.8Vout on/off on/off Figure 9: Turn-on transient at full load (resistive load) (2 ms/div). Ch 1: ON/OFF input (5V/div) Ch 2-4: Vout (1V/div) Figure 10: Turn-on transient at zero load (2 ms/div). Ch 1: ON/OFF input (5V/div) Ch 2-4: Vout (1V/div) 5.0Vout 3.3Vout 1.8Vout 0.8Vout Iout 5.0Vout 3.3Vout 1.8Vout 0.8Vout Iout Figure 11: Output voltage response for 1.5V, 2.5V, 5V units to step-change in load current (50-75-50% of Iout max; di/dt=0.1A/µs). Load cap: 100 µF, 100mW ESR tant, 22 µF cer. Ch 1: Iout (10A/div), Ch 2-4: Vout (100mV/div). Product # NQ15W50SGA30 Phone 1-888-567-9596 Figure 12: Output voltage response for 1.5V, 2.5V, 5V units to step-change in load current (50-75-50% of Iout max; di/dt=3A/µs). Load cap: 100 µF, 100mW ESR tant, 22 µF cer. Ch 1: Iout (10A/div), Ch 2-4: Vout (100mV/div). Doc.# 005-2NS163E Rev. C 10/03/08 Page 6 www.synqor.com Technical Specification See Fig. 14 source impedance Input: Outputs: Current: Package: 6.0 - 15.0V 0.8 - 5.0V 30A SMT 1 µH See Fig. 15 See Fig. 16 5.0Vout iS VSOURCE VIN DC/DC Converter VOUT 22 µF 100 µF 100mW ESR tantalum capacitor 3.3Vout 1.8Vout C* ceramic capacitor 0.8Vout * See values for recommended external input capacitance. Inductor optional as needed. Figure 13: Test set-up diagram showing measurement points for Input Reflected Ripple Current (Figure 14), Input Terminal Ripple Voltage (Figure 15), and Output Voltage Ripple (Figure 16). Figure 14: Input Reflected Ripple Current, is, through a 1 µH source inductor at nominal input voltage and rated load current (100 mA/div). See Figure 13. 0.8Vout 5.0Vout 1.8Vout 3.3Vout 3.3Vout 1.8Vout 5.0Vout 0.8Vout Figure 15: Input Terminal Ripple Voltage at nominal input voltage and rated load current (200 mV/div). Load capacitance: 22 µF ceramic cap and 100 µF tantalum cap. Bandwidth: 20 MHz. See Figure 13. Figure 16: Output Voltage Ripple at nominal input voltage and rated load current (50 mV/div). Load capacitance: 22 µF ceramic cap and 100 µF tantalum cap.. Bandwidth: 20 MHz. See Figure 13. Product # NQ15W50SGA30 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2NS163E Rev. C 10/03/08 Page 7 Technical Specification BASIC OPERATION AND FEATURES The NiQor series non-isolated converter uses a buck-converter that keeps the output voltage constant over variations in line, load, and temperature. The NiQor modules employ synchronous rectification for very high efficiency. Dissipation throughout the converter is so low that it does not require a heatsink or metal baseplate for operation. The NiQor converter can thus be built more simply and reliably using high yield surface mount techniques on a single PCB substrate. The NiQor series of SIPs and SMT converters uses the established industry standard footprint and pin-out configurations. Input: Outputs: Current: Package: 6.0 - 15.0V 0.8 - 5.0V 30A SMT For a desired increase of the nominal output voltage, the value of the resistor should be: Rtrim-up = 1200 VDES - 0.8 or 1200 _ 100 (W) VOUT = 0.8+ where Rtrim-up + 100 (W) VDES = Desired Output Voltage CONTROL FEATURES REMOTE ON/OFF: The ON/OFF input permits the user to control when the converter is on or off. There are currently two options available for the ON/OFF input described in the table below. Others may become available if demand exists. To maintain the accuracy of the output voltage over load current, it is vital that any trim-up resistor be terminated directly to the converter’s ground foot, not at the connection to the load. A separate Kelvin connection to the PCB pad for the ground foot is optimal. Trim-down resistors should be terminated at the converter’s Sense+ pin. We do not recommend bypassing the trim pin directly to ground with a capacitor. The voltage gain from the trim pin to output is rather large, 15:1. Ground bounce through a bypass capacitor could introduce significant noise to the converter’s control circuit. PROTECTION FEATURES OUTPUT VOLTAGE TRIM: The TRIM input permits the user to adjust the output voltage according to the trim range specifications by using an external resistor. If the TRIM feature is not being used, leave the TRIM pin disconnected. TRIM-UP: To increase the output voltage from the nominal setpoint of 0.8V using an external resistor, connect the resistor Rtrim-up between the TRIM and the Ground pin according to the diagram below. Input Under-Voltage Lockout: The converter is designed to turn off when the input voltage is too low, helping avoid an input system instability problem, described in more detail in the application note titled “Input System Instability”. The lockout circuitry is a comparator with DC hysteresis. When the input voltage is rising, it must exceed the typical Turn-On Voltage Threshold value (listed on the specification page) before the converter will turn on. Once the converter is on, the input voltage must fall below the typical Turn-Off Voltage Threshold value before the converter will turn off. Output Current Limiting: To provide protection in an output over load fault condition, the unit is equipped with internal overcurrent protection. When the over-current protection is triggered, the unit enters hiccup mode. The units operate normally once the fault condition is removed. Internal Over-Voltage Protection: To fully protect from excessive output voltage, this series contains contains an Output Over-Voltage Shutdown circuitry. This OVP is independent of the trimmed setpoint. As such, the converter’s load is protected from faults in the external trim circuitry (such as a trim pin shorted to ground). Since the setpoint of this OVP does not track trim, it is set at 6.0V. For more detailed information contact SynQor technical support. Vin Vout Sense+ Trim On/Off Gnd Rtrim-up Product # NQ15W50SGA30 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2NS163E Rev. C 10/03/08 Page 8 Technical Specification Over-Temperature Shutdown: A temperature sensor on the converter senses the average temperature of the module. The thermal shutdown circuit is designed to turn the converter off when the temperature at the sensed location reaches the Over-Temperature Shutdown value. It will allow the converter to turn on again when the temperature of the sensed location falls by the amount of the Over-Temperature Shutdown Restart Hysteresis value. Input: Outputs: Current: Package: 6.0 - 15.0V 0.8 - 5.0V 30A SMT APPLICATION CONSIDERATIONS Input Filtering/Capacitance/Damping: The filter circuit of Figure E is often added to the converter’s input to prevent switching noise from reaching the input voltage bus. Figure H: Converter with Additional Output Capacitance Active Load Sharing: For additional power requirements, the SGA30 series of converters have a parallel feature available. To implement forced load sharing, the following connections should be made: • The share pins of all units in parallel must be connected together. The path of these connections should be as direct as possible. • All ON/OFF pins should be connected together. Figure E: converter with Input Filter In the SGA30 (surface mount) converters Cin = 20µF of high quality ceramic capacitors. With Lin of 1µH, Cd should be 100-200µF and Rd should be 0.1-0.2W, in most applications. For more information on designing the input filter and choosing proper values, contact SynQor technical support. Adding significant external pure ceramic capacitance directly across the converter’s input pins is not recommended. Parasitic inductance associated with the input pin geometry and PCB traces can create a high-Q CLC circuit with any external capacitors. Just a few nano-Henries of parasitic inductance can create a resonance (or an overtone) near the converter’s switching frequency. To avoid this high-frequency resonance, any external input filter should exhibit a net source impedance of at least 20mW resistive through this frequency range. This requirement is easily met with the damping elements discussed above. Adding a small amount (a few µF) of high-frequency external ceramic will not violate it. If using converters at higher powers, consider the ripple current rating of Cd. Contact SynQor technical support for details. Output Capacitance: It is recommended to add at least 100µF of capacitance, with an ESR in the 0.1W range, to the output of the SGA30 series of converters. In many applications, however, additional external output capacitance is required to reduce the response to load transients to an allowable level. For minimal overshoot upon recovery, Cd should be related to the minimum in-circuit net ESR. For more detailed derivations of these values contact SynQor technical support. The share bus is not designed for redundant operation and the system will be non-functional upon failure of one of the units when multiple units are in parallel. When not using the parallel feature, leave the share pin open. SURFACE MOUNT INFORMATION PCB Layout Considerations: SynQor recommends that the customer use a non-solder mask defined pad design. The minimum recommended pad size is 0.074” x 0.122” (1.88mm x 3.1mm) and the maximum pad size is 0.095” x 0.140” (2.41mm x 3.56mm), see the mechanical diagram on page 2. Interconnection to internal power planes is typically required. This can be accomplished by placing a number of vias between the SMT pad and the relevant plane. The number and location of the vias should be determined based on electrical resistance, current and thermal requirements. “Via-in-pad” design should be avoided in the SMT pads. Solder mask should be used to eliminate solder wicking into the vias. Pick and Place: The NiQor surface mount modules are designed for automated assembly using standard SMT pick and place equipment. The modules have a centrally located inductor component with a flat surface area to be used for component pick-up. The units use open frame construction and have a low mass that is within the capability of standard pick and place equipment. Those modules however have a larger mass than most conventional SMT components and so variables such as nozzle size, tip style, handling speed, and placement pressure should be optimized for best results. A conformal tipped placement nozzle design is recommended. Coplanarity of better than 0.004” (0.1mm) is achieved through the SMT NiQor’s terminal design. Product # NQ15W50SGA30 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2NS163E Rev. C 10/03/08 Page 9 Technical Specification Reflow Soldering Guidelines: Figure J shows a typical reflow profile for a eutectic solder process. Due to variations in customer applications, materials and processes, it is not feasible for SynQor to recommend a specific reflow profile. The customer should use this profile as a guideline only. Since the NiQor surface mount modules have a larger thermal mass and lower thermal resistance than standard SMT components, it may be necessary to optimize the solder reflow profile based on limitations of the other components on the customer board. Sufficient reflow time must be allowed to fuse the plating on the connection to ensure a reliable solder joint. The solder reflow profile should be confirmed by accurately measuring the SMT interconnect leads. Maximum case temperature of 260°C (exposure for 5 seconds or less) is not exceeded for the NiQor units. Moisture Sensitivity: The NiQor surface mount modules have an MSL rating 1 per IPC/ JEDEC J-STD-033A. Input: Outputs: Current: Package: Maximum Temperature (+210-260oC) 6.0 - 15.0V 0.8 - 5.0V 30A SMT Eutectic Solder Melting Point (+183oC) (+150-155oC) Pre-heat Soak • 0.5-0.6oC/sec Reflow • 1.3-1.6oC/sec • 30 Cool Down • < 2.5oC/sec • 60 to 90 sec., typ., 2 min max to 60 sec., typ., 90 sec max 2 to 4 min. Figure J: Typical Eutectic (96.5Sn/3.0Ag/0.5Cu) Solder Profile Cleaning and Drying: When possible, a no-clean solder paste system should be used to solder the NiQor SMT units to their application board. The modules are suitable for aqueous washing, however, the user must ensure sufficient drying to remove all water from the converter before powering up. Inadequate cleaning and drying can affect the reliability of the converter and the testing of the final assembly. Product # NQ15W50SGA30 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2NS163E Rev. C 10/03/08 Page 10 Technical Specification PART NUMBERING SYSTEM The part numbering system for SynQor’s dc-dc converters follows the format shown in the example below. NQ 15 W 5 0 S G A 3 0 PSD -G 6/6 RoHS Options (see Ordering Information) Output Current Thermal Design Performance Level Package Size Output Voltage Input Voltage Product Family Model Number NQ15W50SGA30xyz-G Input: Outputs: Current: Package: ORDERING INFORMATION 6.0 - 15.0V 0.8 - 5.0V 30A SMT The tables below show the valid model numbers and ordering options for converters in this product family. When ordering SynQor converters, please ensure that you use the complete 15 character part number consisting of the 12 character base part number and the additional 3 characters for options. A “-G” suffix indicates the product is 6/6 RoHS compliant. Input Voltage 6.0 - 15 V Output Voltage 0.8 - 5.0 V Max Output Current 30 A The first 12 characters comprise the base part number and the last 3 characters indicate available options. The “-G” suffix indicates 6/6 RoHS compliance. The following options must be included in place of the x y z spaces in the model numbers listed above. Options Description: x y z Enable Logic N - Negative P - Pos/Open Pin Style S - Standard Feature Set D - Sense, Share G - Sense, Share, GND pins Application Notes A variety of application notes and technical white papers can be downloaded in pdf format from our website. RoHS Compliance: The EU led RoHS (Restriction of Hazardous Substances) Directive bans the use of Lead, Cadmium, Hexavalent Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. This SynQor product is 6/6 RoHS compliant. For more information please refer to SynQor’s RoHS addendum available at our RoHS Compliance / Lead Free Initiative web page or e-mail us at rohs@synqor.com. Not all combinations make valid part numbers, please contact SynQor for availability. PATENTS SynQor holds the following patents, one or more of which might apply to this product: 5,999,417 6,594,159 6,927,987 7,119,524 6,222,742 6,731,520 7,050,309 7,269,034 6,545,890 6,894,468 7,072,190 7,272,021 6,577,109 6,896,526 7,085,146 7,272,023 Contact SynQor for further information: Phone: Toll Free: Fax: E-mail: Web: Address: 978-849-0600 888-567-9596 978-849-0602 power@synqor.com www.synqor.com 155 Swanson Road Boxborough, MA 01719 USA Phone 1-888-567-9596 Warranty SynQor offers a two (2) year limited warranty. Complete warranty information is listed on our website or is available upon request from SynQor. Information furnished by SynQor is believed to be accurate and reliable. However, no responsibility is assumed by SynQor for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SynQor. Product # NQ15W50SGA30 www.synqor.com Doc.# 005-2NS163E Rev. C 10/03/08 Page 11