Technical S pecification
PQ30033EGA20
18-60V 3.3Vout
Input Output
20Amp
Current
2000Vdc
Isolation
Eighth-brick
DC/DC Conver ter
T h e P Q 3 0 0 3 3 E G A 2 0 P o w e r Qor ® M e g a e i g h t h - b r i c k converter is a next-generation, board-mountable, isolated, fixed switching frequency DC/DC converter that uses synchronous rectification to achieve extremely high conversion efficiency. The power dissipated by the converter is so low that a heatsink is not required, which saves cost, weight, height, and application effort. All of the power and control components are mounted to the multi-layer PCB substrate with high-yield surface mount technology. Since the PowerQor converter has no explicit thermal interfaces, it is extremely reliable. RoHS Compliant (see page 13). Operational Features
• High efficiency, 85% at full rated load current • Delivers up to 20 amps of output current with minimal derating - no heatsink required • Wide input voltage range: 18V – 60V, with 80V 100ms input voltage transient capability • Fixed frequency switching provides predictable EMI performance • No minimum load requirement means no preload resistors required
PQ30033EGA20 Module
Pr otection Features
• Input under-voltage lockout disables converter at low input voltage conditions • Output current limit and short circuit protection protects converter and load from permanent damage and consequent hazardous conditions • Active back bias limit prevents damage to converter from external load induced pre-bias • Output over-voltage protection protects load from damaging voltages • Thermal shutdown protects converter from abnormal environmental conditions
Mechanical Features
• Industry standard eighth-brick pin-out configuration • Industry standard size: 0.90” x 2.3” (22.9x58.4mm) • Total height only 0.335” (8.5mm), permits better airflow and smaller card pitch • Total weight: 0.68 oz. (19 grams) • Flanged pins designed to permit surface mount soldering (avoid wave solder) using FPiP technique
Contr ol Features
• On/Off control referenced to input side (positive and negative logic options are available) • Remote sense for the output voltage compensates for output distribution drops • Output voltage trim permits custom voltages and voltage margining
Product # PQ30033EGA20 Phone 1-888-567-9596 www.synqor.com
• 2000V, 30MΩ input-to-output isolation provides input/output ground separation • UL/cUL 60950-1 recognized (US & Canada) • TUV certified to EN60950-1 • Meets 72/23/EEC and 93/68/EEC directives which facilitates CE Marking in user’s end product • Board and plastic components meet UL94V-0 flammability requirements
Safety Features
Doc.# 005-2EG33MU Rev. A
3/18/08
Page 1
Technical Specification
MECHANICAL DIAGRAM
0.14 0.150
(3.81) (3.56)
Input: I nput: Output: Current: Package:
18-60 V 3.3 V 20 A Eighth-brick
2.30
(58.42)
0.300
(7.62)
2.00
(50.8)
0.150
(3.81)
0.450
(11.43)
0.600
(15.24)
0.90
(22.86)
Top View
0.600
(15.24)
0.300
(7.62)
0.335
Side View
Bottom side Clearance
(8.5)
0.019 +0.013
(0.48 +0.33)
Lowest Component
Load Board
Flanged Pin See Note 9
0.110
(2.79) See Note 3
NOTES
PIN DESIGNATIONS
1) Pins 1-3, 5-7 are 0.040” (1.02mm) diameter. with Pin No. Name Function 0.080” (2.03mm) diameter standoff shoulders. 1 Vin(+) Positive input voltage 2) Pins 4 and 8 are 0.062” (1.57 mm) diameter with 0.100” (2.54 mm) diameter standoff shoulders. 2 ON/OFF TTL input to turn converter 3) Other pin extension lengths available. Recommended pin on and off, referenced to length is 0.03” (0.76mm) greater than the PCB thickness. Vin(-), with internal pull up. 4) All Pins: Material - Copper Alloy 3 Vin(-) Negative input voltage Finish (RoHS 5/6) - Tin/Lead over Nickel plate 4 Vout(-) Negative output voltage Finish (RoHS 6/6) - Matte Tin over Nickel plate 5 SENSE(-) Negative remote sense1 5) Undimensioned components are shown for visual reference only. 6) All dimensions in inches (mm) 6 TRIM Output voltage trim2 Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) 7 SENSE(+) Positive remote sense3 x.xxx +/-0.010 in. (x.xx +/-0.25mm) 8 Vout(+) Positive output voltage 7) Weight: 0.68 oz. (19 g) typical 8) Workmanship: Meets or exceeds IPC-A-610C Class II Notes: 9) The flanged pins are designed to permit surface mount soldering (allowing to avoid the wave soldering process) 1. SENSE(–) should be connected to Vout(–) either remotely or at the converter. through the use of the flanged pin-in-paste technique. 2. Leave TRIM pin open for nominal output voltage. 3. SENSE(+) should be connected to Vout(+) either remotely or at the converter.
Product # PQ30033EGA20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG33MU Rev. A
3/18/08
Page 2
Technical Specification
PQ30033EGA20 ELECTRICAL CHARACTERISTICS
Parameter
ABSOLUTE MAXIMUM RATINGS
Input: I nput: Output: Current: Package:
18-60 V 3.3 V 20 A Eighth-brick
TA=25°C, airflow rate=300 LFM, Vin=48Vdc unless otherwise noted; full operating temperature range is -40°C to +100°C ambient temperature with appropriate power derating. Specifications subject to change without notice.
Min. Typ. Max.
80 60 80 2000 100 125 18 24\48 16.6 15.0 3.5 40 4 150 3 420 2.2\1.5 47 3.267 3.300 60 17.5 15.9 4.5 4.5 60 7 0.01
Units
V V V V °C °C V V V V V A mA mA A 2s mV mA mA A µF\µH µF V %\mV %\mV mV V mV mV A A V A mA µF dB mV mV µs
Notes & Conditions
Continuous Continuous 100ms transient, square wave Basic insulation, Pollution Degree 2
Input Voltage Non-Operating Operating Operating Transient Protection Isolation Voltage (input to output) Operating Temperature Storage Temperature Voltage at ON/OFF input pin Operating Input Voltage Range Input Under-Voltage Lockout Turn-On Voltage Threshold Turn-Off Voltage Threshold Lockout Voltage Hysteresis Maximum Input Current No-Load Input Current Disabled Input Current Inrush Current Transient Rating Response to Input Transient Input Reflected Ripple Current Input Terminal Ripple Current Recommended Input Fuse Input Filter Component Values (C\L) Recommended External Input Capacitance
-40 -55 -2 18 15.7 14.1 2.5
INPUT CHARACTERISTICS
100% Load, 18 Vin
20
OUTPUT CHARACTERISTICS
1000V/ms input transient RMS thru 10µH inductor; Figures 17 & 19 RMS; Figures 17 & 18 Fast blow external fuse recommended Internal values; see Figure E Typical ESR 0.1-0.2Ω; see Figure 17
Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise1 Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance
3.333
3.207
+0.05 \ 2 +0.15 \ 5 +0.05 \ 2 +0.15 \ 5 +17 +50 3.393 70 15 24 2.4 0.5 10 70 150 150 800 9 200 0 85.0 87. 82.0 83.5 125 125 125 2000 30 470 13 240 130 25 20 26.5 50 20,000
0 21.5
Over sample, line, load, temperature & life 20MHz bandwidth; Figures 17 & 20 Full Load; Figures 17 & 20 Full Load; Figures 17 & 20 Subject to thermal derating; Figures 5 - 12 Output Voltage 10% Low; Figure 21 Negative current drawn from output Negative current drawn from output 3.3Vout at 15A Resistive Load 120 Hz; Figure 24 50% to 75% to 50% Iout max; Figure 15 50% to 75% to 50% Iout max; Figure 16 To within 1% Vout nom Full load, Vout=90% nom.; Figures 13 & 14 -40°C to +125°C; Figure F 20,000 µF load capacitance, Iout = 0A Figures Figures Figures Figures 1 1 1 1 4 4 4 4
DYNAMIC CHARACTERISTICS
Input Voltage Ripple Rejection Output Voltage during Load Current Transient For a Step Change in Output Current (0.1A/µs) For a Step Change in Output Current (5A/µs) Settling Time Turn-On Transient Turn-On Time Start-Up Inhibit Time 180 Output Voltage Overshoot EFFICIENCY 100% Load 24Vin 50% Load 24Vin 100% Load 48Vin 50% Load 48Vin TEMPERATURE LIMITS FOR POWER DERATING CURVES Semiconductor Junction Temperature Board Temperature Transformer Temperature Isolation Voltage (dielectric strength) Isolation Resistance Isolation Capacitance2
ms ms % % % % % °C °C °C V MΩ pF
Package rated to 150°C UL rated max operating temp 130°C See Figures 5 - 12 for derating curves
ISOLATION CHARACTERISTICS
Note 1: For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Higher values of isolation capacitance can be added external to the module.
Product # PQ30033EGA20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG33MU Rev. A
3/18/08
Page 3
Technical Specification
ELECTRICAL CHARACTERISTICS (Continued)
Parameter P
FEATURE CHARACTERISTICS
Input: I nput: Output: Current: Package:
18-60 V 3.3 V 20 A Eighth-brick
Min.
260 -2 2.4 2.4 -2
Typ.
290
Max.
320 0.8 18 18 0.8
Units
kHz V V V V V kΩ % % % °C °C
6
Notes & Conditions
Buck stage and isolation stage
Switching Frequency ON/OFF Control (Option P) Off-State Voltage On-State Voltage ON/OFF Control (Option N) Off-State Voltage On-State Voltage ON/OFF Control (Either Option) Pull-Up Voltage Pull-Up Resistance Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection Over-Temperature Shutdown Over-Temperature Shutdown Restart Hysteresis Load Current Scale Factor Calculated MTBF (Telcordia) Calculated MTBF (MIL-217) Field Demonstrated MTBF
-10 117
Vin/6.5 40 122 125 10 800 2.4 1.4
9.2 +10 +10 127
Figures A & B Measured across Pins 8 & 4; Figure C Measured across Pins 8 & 4 Over full temp range; % of nominal Vout Average PCB Temperature See web App Note: Output Load Current Calc.
RELIABILITY CHARACTERISTICS
10 Hrs. TR-NWT-000332; 80% load,300LFM, 40oC Ta 106 Hrs. MIL-HDBK-217F; 80% load, 300LFM, 40oC Ta 106 Hrs. See our website for details
STANDARDS COMPLIANCE
Parameter P
STANDARDS COMPLIANCE
Notes
File # E194341, Basic insulation & pollution degree 2 Certified by TUV Test on entire assembly; board & plastic components UL94V-0 compliant ESD test, 8kV - NP, 15kV air - NP (Normal Performance) Section 7 - electrical safety, Section 9 - bonding/grounding
UL/cUL 60950-1 EN60950-1 72/23/EEC 93/68/EEC Needle Flame Test (IEC 695-2-2) IEC 61000-4-2 GR-1089-CORE Telcordia (Bellcore) GR-513
• An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or download from the SynQor website.
QUALIFICATION TESTING
Parameter P
QUALIFICATION TESTING
# Units
32 5 5 10 5 5 5 15 pins
Test Conditions
10-55Hz sweep, 0.060” total excursion,1 min./sweep, 120 sweeps for 3 axis
Life Test Vibration Mechanical Shock Temperature Cycling Power/Thermal Cycling Design Marginality Humidity Solderability
95% rated Vin and load, units at derating point, 1000 hours
100g minimum, 2 drops in x and y axis, 1 drop in z axis -40°C to 100°C, unit temp. ramp 15°C/min., 500 cycles Toperating = min to max, Vin = min to max, full load, 100 cycles Tmin-10°C to Tmax+10°C, 5°C steps, Vin = min to max, 0-105% load 85°C, 85% RH, 1000 hours, 2 minutes on and 6 hours off MIL-STD-883, method 2003
• Extensive characterization testing of all SynQor products and manufacturing processes is performed to ensure that we supply robust, reliable product. Contact the factory for official product family qualification documents.
OPTIONS
SynQor provides various options for this family of dc-dc converters. Please consult the last page for additional information.
PATENTS
SynQor is protected under various patents. Please consult the last page for further details.
Product # PQ30033EGA20
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG33MU Rev. A
3/18/08
Page 4
Technical Specification
100 95 86.8 90 87.0
Input: I nput: Output: Current: Package:
18-60 V 3.3 V 20 A Eighth-brick
Efficiency (%)
Efficiency (%)
18 Vin 24 Vin 48 Vin 60 Vin
85 80 75 70 65 60 0 4 8 12 16 20
86.6
86.4
86.2
25 ºC 40 ºC 55 ºC
86.0 100 200 300 400
Load Current (A)
Air Flow (LFM)
Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25°C.
Figure 2: Efficiency at nominal output voltage and 60% rated power vs. airflow rate for ambient air temperatures of 25°C, 40°C, and 55°C (nominal input voltage).
7.0
15 14 13 12
Power Dissipation (W)
10 9 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 18 Vin 24 Vin 48 Vin 60 Vin
Power Dissipation (W)
11
6.0
5.0
4.0
25 ºC 40 ºC 55 ºC
3.0 100 200 300 400
Load Current (A)
Air Flow (LFM)
Figure 3: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25°C.
Figure 4: Power dissipation at nominal output voltage and 60% rated power vs. airflow rate for ambient air temperatures of 25°C, 40°C, and 55°C (nominal input voltage).
22 20 18 16 14
Iout (A)
12 10 8 6 4 2 0 25 40 55 70 85 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s)
Semiconductor junction temperature is within 1°C of surface temperature
Ambient Air Temperature (°C)
Figure 5: Maximum output power derating curves vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM with air flowing across the converter from pin 3 to pin 1 (24V input voltage).
Product # PQ30033EGA20 Phone 1-888-567-9596
Figure 6: Thermal plot of converter at 17.7 amp load current with 55°C air flowing at the rate of 200 LFM. Air is flowing across the converter sideways from pin 3 to pin 1 (24V input voltage).
Doc.# 005-2EG33MU Rev. A 3/18/08 Page 5
www.synqor.com
Technical Specification
22 20 18 16 14
Input: I nput: Output: Current: Package:
18-60 V 3.3 V 20 A Eighth-brick
Iout (A)
12 10 8 6 4 2 0 25 40 55 70 85 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s)
Semiconductor junction temperature is within 1°C of surface temperature
Ambient Air Temperature (°C)
Figure 7: Maximum output power derating curves vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM with air flowing across the converter from pin 3 to pin 1 (48V input voltage).
22 20 18 16
Figure 8: Thermal plot of converter at 16.3 amp load current with 55°C air flowing at the rate of 200 LFM. Air is flowing across the converter sideways from pin 3 to pin 1 (48V input voltage).
Iout (A)
14 12 10 8 6 4 2 25 40 55 70 85 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s)
Semiconductor junction temperature is within 1°C of surface temperature
Ambient Air Temperature (°C)
Figure 9: Maximum output power-derating curves vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM with air flowing from input to output (24V input voltage).
22 20 18 16
Figure 10: Thermal plot of converter at 17.4 amp load current with 55°C air flowing at the rate of 200 LFM. Air is flowing across the converter from input to output (24V input voltage).
Iout (A)
14 12 10 8 6 4 2 25 40 55 70 85 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s)
Semiconductor junction temperature is within 1°C of surface temperature
Ambient Air Temperature (°C)
Figure 11: Maximum output power-derating curves vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM with air flowing from input to output (48V input voltage).
Product # PQ30033EGA20 Phone 1-888-567-9596
Figure 12: Thermal plot of converter at 14.5 amp load current with 55°C air flowing at the rate of 200 LFM. Air is flowing across the converter from input to output (48V input voltage).
Doc.# 005-2EG33MU Rev. A 3/18/08 Page 6
www.synqor.com
Technical Specification
Input: I nput: Output: Current: Package:
18-60 V 3.3 V 20 A Eighth-brick
Figure 13: Turn-on transient at full load (resistive load) (5 ms/div). Input voltage pre-applied. Ch 1: Vout (1V/div). Ch 2: ON/OFF input (5V/div)
Figure 14: Turn-on transient at zero load (5 ms/div). Ch 1: Vout (1V/div) Ch 2: ON/OFF input (5V/div)
Figure 15: Output voltage response to step-change in load current (50%-75%-50% of Iout(max); dI/dt = 0.1A/µs). Load cap: 10µF, 100 mΩ ESR tantalum capacitor and 1µF ceramic capacitor. Ch 1: Vout (200mV/div), Ch 2: Iout (5A/div).
Figure 16: Output voltage response to step-change in load current (50%-75%50% of Iout(max): dI/dt = 5A/µ s). Load cap: 470µ F, 30 mΩ ESR tantalum capacitor and 1µ F ceramic cap. Ch 1: Vout (200mV/div), Ch 2: Iout (5A/div).
See Fig. 15
source impedance
10 µH
See Fig. 14 See Fig. 16
iS
VSOURCE
iC
DC/DC Converter 1 µF
VOUT
ceramic 100mΩ ESR capacitor tantalum capacitor
electrolytic capacitor
47 µF,