Technical Specification
PQ60018ETL45
48Vin
Input
1.8Vout
Output
45A
Current
2250Vdc
Isolation
Eighth-brick
DC/DC Converter
The PQ60018ETL45 PowerQor® Tera eighth-brick converter is a next-generation, board-mountable, isolated, fixed switching frequency DC/DC converter that uses synchronous rectification to achieve extremely high conversion efficiency. The power dissipated by the converter is so low that a heatsink is not required, which saves cost, weight, height, and application effort. All of the power and control components are mounted to the multi-layer PCB substrate with high-yield surface mount technology. Since the PowerQor converter has no explicit thermal interfaces, it is extremely reliable. RoHS Compliant (see page 14). Operational Features
• High efficiency, 87% at full rated load current • Delivers up to 45A of output current with minimal derating - no heatsink required • Wide input voltage range: 35-75V, with100V 100ms input voltage transient capability • Fixed frequency switching provides predictable EMI performance • No minimum load requirement - no preload resistors required
PQ60018ETL45 Module
Protection Features
• Input under-voltage lockout disables converter at low input voltage conditions • Output current limit and short circuit protection protects converter and load from permanent damage and consequent hazardous conditions • Active back bias limit prevents damage to converter from external load induced pre-bias • Output over-voltage protection protects load from damaging voltages • Thermal shutdown protects converter from abnormal environmental conditions
Mechanical Features
• Industry standard eighth-brick pin-out configuration • Open frame size: 0.90” x 2.3” (22.9x58.4mm) • Total height only 0.320” (8.13mm) L-option, permits better airflow and smaller card pitch • Open frame total weight: 0.85oz (24g) • Open f rame u nits h ave f langed p ins d esigned t o permit surface mount soldering (avoid wave solder) u sing F PiP t echnique
Safety Features
• 2250 V, 30 MΩ input-to-output isolation • Certified to 60950-1 requirements for basic insulation (see Standards and Qualifications page) • RoHS compliant (see Page 14)
Control Features
• On/Off control referenced to input side (positive and negative logic options are available) • Remote sense for the output voltage compensates for output distribution drops • Output voltage trim permits custom voltages and voltage margining
Product # PQ60018ETL45 Phone 1-888-567-9596
Contents
Mechanical Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 PQ60018ETL45 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . 4-5 PQ60-ET Family Standards and Qualifications (all output voltages) . . . . 5 PQ60018ETL45 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 Application Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Doc.# 005-2ET618F Rev. B 06/01/09
Page No.
www.synqor.com
Page 1
Technical Specification
Mechanical Drawing - Open Frame A option
.900±.022 [22,86± 0,55] .600 [15,24 ] .450 [ 11,43 ] .300 [ 7,62] .150 [ 3,81 ]
Input: Output: Current: Package:
35-75 V 1.8 V 45 A Eighth-brick
.145 [ 3,68 ] SEE NOTE 3
87654
2.30 [ 58,4 ]
2.00 [ 50,8 ]
TOP VIEW
SIDE VIEW
.14 [ 3,6 ]
1
2
3
.300 [ 7,62] .600 [ 15,24 ] .15 [ 3,8 ]
.397[ 10,08 ] OVERALL HEIGHT
.093 [ 2,36 ] BOTTOMSIDE CLEARANCE
NOTES
1) PINS 1-3, 5-7 ARE 0.040" (1.02mm) DIA. WITH 0.080" (2.03mm) DIA. STANDOFF SHOULDERS 2) PINS 4, 8 ARE 0.062" (1.57mm) DIA. WITH 0.100" (2.54mm) DIA. STANDOFF SHOULDERS 3) OTHER PIN EXTENSION LENGTHS AVAILABLE 4) ALL PINS: MATERIAL: COPPER ALLOY FINISH: TIN-LEAD OVER NICKEL PLATE 5) UNDIMENSIONED COMPONENTS ARE SHOWN FOR VISUAL REFERENCE ONLY 6) ALL DIMENSIONS IN INCHES(mm) TOLERANCES: X.XXIN +/-0.02 (X.Xmm +/-0.5mm) X.XXXIN +/-0.010 (X.XXmm +/-0.25mm) Pin 1 2 3 4 5 6 7 8 Notes: 1) 2) 3) Name Vin(+)
PIN DESIGNATIONS
Function Positive input voltage TTL input to turn converter on and off, referenced to Vin(–), with internal pull up. Negative input voltage Negative output voltage Negative remote sense(see note 1) Output voltage trim (see note 2) Positive remote sense (see note 3) Positive output voltage
ON/OFF Vin(–) Vout(–) SENSE(–) TRIM SENSE(+) Vout(+)
SENSE(–) should be connected to Vout(–) either remotely or at the converter. Leave TRIM pin open for nominal output voltage. SENSE(+) should be connected to Vout(+) either remotely or at the converter.
Product # PQ60018ETL45
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ET618F Rev. B
06/01/09
Page 2
Technical Specification
Mechanical Drawing - Open Frame L option
2.30
(58.4)
Input: Output: Current: Package:
35-75 V 1.8 V 45 A Eighth-brick
0.450
(11.43)
2.00
(50.8)
0.14
(3.6)
0.300
(7.62)
0.15
(3.8)
Top View
1 2 3 8 7 6 5 4
0.150
(3.81)
0.600
(15.24)
0.300
(7.62)
0.900 +0.022
(22.86 +0.55)
0.320 +0.015
(8.13 +0.38)
0.600
(15.24)
Overall Height
0.145
(3.68) See Note 3
0.016 +0.015
(0.41 +0.38)
Side View
Lowest Component Load Board Flanged Pin See Note 10
Bottom Side Clearance
NOTES
1) Pins 1-3, 5-7 are 0.040” (1.02mm) diameter. with 0.080” (2.03mm) diameter standoff shoulders. 2) Pins 4 and 8 are 0.062” (1.57 mm) diameter with 0.100” (2.54 mm) diameter standoff shoulders. 3) Other pin extension lengths available. Recommended pin length is 0.03” (0.76mm) greater than the PCB thickness. 4) All Pins: Material - Copper Alloy Finish - Matte Tin over Nickel plate 5) Undimensioned components are shown for visual reference only 6) All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) x.xxx +/-0.010 in. (x.xx +/-0.25mm) 7) Weight: 0.85 oz (24 g) typical 8) Workmanship: Meets or exceeds IPC-A-610C Class II 9) UL/TUV standards require a clearance greater than 0.04” (1.02mm) between input and output for Basic insulation. This issue should be considered if any copper traces are on the top side of the user’s board. Note that the ferrite core shown at left above is considered part of the input/primary circuit and that the two ferrite cores shown at the right above are considered part of the output/secondary circuit.
PIN DESIGNATIONS
Pin 1 2 3 4 5 Name Vin(+) ON/OFF Vin(–) Vout(–) SENSE(–) Function Positive input voltage TTL input to turn converter on and off, referenced to Vin(–), with internal pull up. Negative input voltage Negative output voltage Negative remote sense(see note 1) Output voltage trim (see note 2) Positive remote sense (see note 3) Positive output voltage
6 TRIM 7 SENSE(+) 8 Vout(+) Notes:
1) 2) 3)
SENSE(–) should be connected to Vout(–) either remotely or at the converter. Leave TRIM pin open for nominal output voltage. SENSE(+) should be connected to Vout(+) either remotely or at the converter.
10) The flanged pins are designed to permit surface mount soldering (allowing to avoid the wave soldering process) through the use of the flanged pin-in-paste technique.
Product # PQ60018ETL45 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2ET618F Rev. B 06/01/09 Page 3
Technical Specification
PQ60018ETL45 Electrical Characteristics
Input: Output: Current: Package:
35-75 V 1.8 V 45 A Eighth-brick
TA=25°C, airflow rate=300 LFM, Vin=48Vdc unless otherwise noted; full operating temperature range is -40°C to +100°C ambient temperature with appropriate power derating. Specifications subject to change without notice.
Parameter
ABSOLUTE MAXIMUM RATINGS
Min.
35 -40 -55 -2 35 31.5 29.6 1.9 0 1.785 1.774 0 48 10 180
Typ.
48 32.6 30.6 2.0 46 6 60 2 30 47 1.800 +0.1 \ 1.8 +0.2 \ 3.6 +5 1.800 35 15 52 1.0 4.6 10 67 120 200 1000 13 200 0 87 89 2250 30 3300
Max.
100 75 100 2250 100 125 18 75 33.7 32.5 2.1 2.6 75 10 0.1 20 1.0 \ 3.3 1.817 1.828 45 64 6.5 50 43 5 20 230 125 125 125
Units
V V V V °C °C V V V V V A mA mA A 2s mV mA mA A µH\µF µF V %\mV %\mV mV V mV mV A A V A mA mF mF dB mV mV µs ms ms % % % °C °C °C V MW pF
Notes & Conditions
Continuous Continuous 100ms transient, square wave Basic insulation, Pollution Degree 2
INPUT CHARACTERISTICS
Input Voltage Non-Operating Operating Operating Transient Protection Isolation Voltage (input to output) Operating Temperature Storage Temperature Voltage at ON/OFF input pin Operating Input Voltage Range Input Under-Voltage Lockout Turn-On Voltage Threshold Turn-Off Voltage Threshold Lockout Voltage Hysteresis Maximum Input Current No-Load Input Current Disabled Input Current Inrush Current Transient Rating Response to Input Transient Input Reflected Ripple Current Input Terminal Ripple Current Recommended Input Fuse Input Filter Component Values (L\C) Recommended External Input Capacitance
100% Load, 35 Vin, nominal Vout
OUTPUT CHARACTERISTICS
1000V/ms input transient RMS thru 10µH inductor; Figures 13 & 15 RMS; Figures 13 & 14 Fast blow external fuse recommended Internal values; see Figure E Typical ESR 0.1-0.2W; see Figure 13
DYNAMIC CHARACTERISTICS
Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise1 Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance Electrolytic Maximum Output Capacitance Ceramic Input Voltage Ripple Rejection Output Voltage during Load Current Transient For a Step Change in Output Current (0.1A/µs) For a Step Change in Output Current (1A/µs) Settling Time Turn-On Transient Turn-On Time Restart Inhibit Time Output Voltage Overshoot 100% Load 50% Load
Over sample, line, load, temperature & life 20MHz bandwidth; Figures 13 & 16 Full Load; see Figures 13 & 16 Full Load; see Figures 13 & 16 Subject to thermal derating; Figures 5 - 8 Output Voltage 10% Low Negative current drawn from output Negative current drawn from output 1.8Vout at 45A Resistive Load 1.8Vout at 45A Resistive Load 120 Hz; Figure 20 50% to 75% to 50% Iout max; Figure 11 50% to 75% to 50% Iout max; Figure 12 To within 1% Vout nom Full load, Vout=90% nom.; Figures 9 & 10 -40°C to +125°C; Figure F No load capacitance, Iout = 0A Figures 1 - 4 Figures 1 - 4 Package rated to 150°C UL rated max operating temp 130°C See Figures 5 - 8 for derating curves
EFFICIENCY
TEMPERATURE LIMITS FOR POWER DERATING CURVES
ISOLATION CHARACTERISTICS
Semiconductor Junction Temperature Board Temperature Transformer Temperature Isolation Voltage (dielectric strength) Isolation Resistance Isolation Capacitance2
Note 1: Output voltage ripple can exceed maximum specification during startup when output voltage is less than 0.7V. Additional output capacitance will mitigate this startup ripple behavior. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Higher values of isolation capacitance can be added external to the module.
Product # PQ60018ETL45
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ET618F Rev. B
06/01/09
Page 4
Technical Specification
PQ60018ETL45 Electrical Characteristics (Continued)
Parameter P
FEATURE CHARACTERISTICS
Input: Output: Current: Package:
35-75 V 1.8 V 45 A Eighth-brick
Min.
300 -2 2.4 2.4 -2 -20 117
Typ.
333 5 10 133 120 10 2.42 2.27
Max.
360 0.8 18 18 0.8 6 +10 +10 142
Units
kHz V V V V V kW % % % °C °C
Notes & Conditions
RELIABILITY CHARACTERISTICS
Switching Frequency ON/OFF Control (Option P) Off-State Voltage On-State Voltage ON/OFF Control (Option N) Off-State Voltage On-State Voltage ON/OFF Control (Either Option) Pull-Up Voltage Pull-Up Resistance Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection Over-Temperature Shutdown Over-Temperature Shutdown Restart Hysteresis Calculated MTBF (Telcordia) Calculated MTBF (MIL-217) Field Demonstrated MTBF
Figures A & B Measured across Pins 8 & 4; Figure C Measured across Pins 8 & 4 Over full temp range; % of nominal Vout Average PCB Temperature
106 Hrs. TR-NWT-000332; 80% load,300LFM, 40oC Ta 106 Hrs. MIL-HDBK-217F; 80% load, 300LFM, 40oC Ta 106 Hrs. See our website for latest values
PQ60-ET Family Standards and Qualifications (all output voltages)
Parameter
STANDARDS COMPLIANCE UL/cUL 60950-1 EN60950-1 Needle Flame Test (IEC 695-2-2) IEC 61000-4-2 File # E194341, Basic insulation Certified by TUV Test on entire assembly; board & plastic components UL94V-0 compliant ESD test, 8 kV - NP, 15 kV air - NP (Normal Performance)
Notes & Conditions
Note: An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or download from the SynQor website.
Parameter
QUALIFICATION TESTING Life Test Vibration Mechanical Shock Temperature Cycling Power/Thermal Cycling Design Marginality Humidity
# Units
32 5 5 10 5 5 5
Test Conditions
95% rated Vin and load, units at derating point, 1000 hours 10-55 Hz sweep, 0.060" total excursion, 1 min./sweep, 120 sweeps for 3 axis 100g minimum, 2 drops in x and y axis, 1 drop in z axis -40 °C to 100 °C, unit temp. ramp 15 °C/min., 500 cycles Toperating = min to max, Vin = min to max, full load, 100 cycles Tmin-10 °C to Tmax+10 °C, 5 °C steps, Vin = min to max, 0-105% load 85 °C, 85% RH, 1000 hours, continuous Vin applied except 5 min/day
Product # PQ60018ETL45
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ET618F Rev. B
06/01/09
Page 5
Technical Specification
100 95 90 94 93 92
Input: Output: Current: Package:
35-75 V 1.8 V 45 A Eighth-brick
Efficiency (%)
80 75 70 65 60 0 5 10 15 20 25 30 35 40 45 35 Vin 48 Vin 75 Vin
Efficiency (%)
85
91 90 89 88 87 86 100 200 300 400 25º C 40º C 55º C
Load Current (A)
Air Flow (LFM)
Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25°C.
Figure 2: Efficiency at nominal output voltage and 60% rated power vs. airflow rate for ambient air temperatures of 25°C, 40°C, and 55°C (nominal input voltage).
8 7
14 12
Power Dissipation (W)
Power Dissipation (W)
10 8 6 4 2 0 0 5 10 15 20 25 30 35 40 45 35 Vin 48 Vin 75 Vin
6 5 4 3 2 1 100 200 300 400 25º C 40º C 55º C
Load Current (A)
Air Flow (LFM)
Figure 3: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25°C.
Figure 4: Power dissipation at nominal output voltage and 60% rated power vs. airflow rate for ambient air temperatures of 25°C, 40°C, and 55°C (nominal input voltage).
50
40
Iout (A)
30
20 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 10 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 0 25 40 55 70 85
Ambient Air Temperature (ºC)
Figure 5: Maximum output power-derating curves vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM with air flowing from pin 3 to pin 1(nominal input voltage).
Product # PQ60018ETL45 Phone 1-888-567-9596
Figure 6: Thermal plot of an open frame converter at 36.5 amp load current (65.6W) with 70°C air flowing at the rate of 200 LFM. Air is flowing across the converter from 3 to pin 1 (nominal input voltage).
Doc.# 005-2ET618F Rev. B 06/01/09 Page 6
www.synqor.com
Technical Specification
50
Input: Output: Current: Package:
35-75 V 1.8 V 45 A Eighth-brick
40
Iout (A)
30
20 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 10 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 0 25 40 55 70 85
Ambient Air Temperature (ºC)
Figure 7: Maximum output power derating curves vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM with air flowing across the converter from pin input to output (nominal input voltage).
Figure 8: Thermal plot of an open frame converter at 35.6 amp load current (64.0W) with 70°C air flowing at the rate of 200 LFM. Air is flowing across the converter from input to output (nominal input voltage).
Figure 9: Turn-on transient at full load (resistive load) (5 ms/div). Load cap: 10 uF, 100 mW ESR tantalum capacitor and 1 uF ceramic capacitor. Input voltage pre-applied. Ch 1: Vout (500 mV/div), Ch 2: ON/OFF input (5 V/div).
Figure 10: Turn-on transient at zero load (5 ms/div). Load cap: 10 uF, 100 mW ESR tantalum capacitor and 1 uF ceramic capacitor. Ch 1: Vout (500 mV/div), Ch 2: ON/OFF input (5 V/div).
75%-50% of Iout(max); dI/dt = 0.1A/µs). Load cap: 10µF, 100 mW ESR tantalum cap and 1µF ceramic cap. Ch 1: Vout (100mV/div), Ch 2: Iout (20A/div).
Product # PQ60018ETL45 Phone 1-888-567-9596
Figure 11: Output voltage response to step-change in load current (50%-
Figure 12: Output voltage response to step-change in load current (50%-
75%-50% of Iout(max): dI/dt = 1A/µs). Load cap: 470µF, 30 mW ESR tantalum cap and 1µF ceramic cap. Ch 1: Vout (200mV/div), Ch 2: Iout (20A/div).
Doc.# 005-2ET618F Rev. B 06/01/09 Page 7
www.synqor.com
Technical Specification
See Fig. 15
source impedance
Input: Output: Current: Package:
35-75 V 1.8 V 45 A Eighth-brick
10 µH
See Fig. 14 See Fig. 16
iS
VSOURCE
iC
DC/DC Converter 1 µF
VOUT
15 µF,
electrolytic capacitor
47 µF,