FR207-STR

FR201 - FR207-STR PRV : 50 - 1000 Volts Io : 2.0 Amperes FEATURES : * * * * * * High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency FAST RECOVERY RECTIFIER DIODES D2 0.161 (4.1) 0.154 (3.9) 1.00 (25.4) MIN. 0.284 (7.2) 0.268 (6.8) MECHANICAL DATA : * Case : D2 Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.465 gram 0.034 (0.86) 0.028 (0.71) 1.00 (25.4) MIN. Dimensions in inches and ( millimeters ) Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS RATING Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Current 0.375"(9.5mm) Lead Length Peak Forward Surge Current, 8.3ms Single half sine wave Superimposed on rated load (JEDEC Method) Maximum Peak Forward Voltage at IF = 2.0 Amps. Maximum DC Reverse Current at Rated DC Blocking Voltage Ta = 25 °C Ta = 100 °C Ta = 55 °C SYMBOL FR201 FR202 FR203 FR204 FR205 FR206 FR207 FR207 -STR UNIT VRRM VRMS VDC IF(AV) 50 35 50 100 70 100 200 140 200 400 280 400 2.0 600 420 600 800 560 800 1000 700 1000 1000 700 1000 V V V A IFSM VF IR IR(H) Trr 75 1.3 10 500 150 15 - 65 to + 150 - 65 to + 150 250 500 250 A V µA µA ns pf °C °C Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Junction Temperature Range Storage Temperature Range Notes : CJ TJ TSTG ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC Page 1 of 2 Rev. 01 : January 10, 2004 RATING AND CHARACTERISTIC CURVES ( FR201 - FR207-STR ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω + 0.5 A D.U.T. 50 Vdc (approx) 1Ω PULSE GENERATOR ( NOTE 2 ) OSCILLOSCOPE ( NOTE 1 ) 0 - 0.25 A Trr + - 1.0 A SET TIME BASE FOR 50-100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. 1 cm FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 2.0 75 FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES 8.3 ms SINGLE HALF SINE WAVE 60 Ta = 55 °C 45 AVERAGE FORWARD OUTPUT CURRENT, AMPERES 1.6 1.2 0.8 30 0.4 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 175 15 0 1 2 4 6 10 20 40 60 100 AMBIENT TEMPERATURE, ( °C) FIG.4 - TYPICAL FORWARD CHARACTERISTICS NUMBER OF CYCLES AT 60Hz FIG.5 - TYPICAL REVERSE CHARACTERISTICS 100 10 FORWARD CURRENT, AMPERES TJ = 25 °C 10 REVERSE CURRENT, MICROAMPERES Pulse Width = 300 µs 2% Duty Cycle TJ = 100 °C 1.0 1.0 0.1 TJ = 25 °C 0.1 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE, VOLTS Page 2 of 2 Rev. 01 : January 10, 2004