RGP10B

RGP10A - RGP10M PRV : 50 - 1000 Volts Io : 1.0 Ampere FEATURES : * * * * * * High current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Pb / RoHS Free FAST RECOVERY RECTIFIERS DO - 41 1.00 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) 0.205 (5.2) 0.166 (4.2) MECHANICAL DATA : * Case : DO-41 Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.339 gram Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. 0.034 (0.86) 0.028 (0.71) 1.00 (25.4) MIN. Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS RATING Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Current 0.375"(9.5mm) Lead Length Ta = 55 °C Peak Forward Surge Current, 8.3ms Single half sine wave Superimposed on rated load (JEDEC Method) Maximum Peak Forward Voltage at IF = 1.0 A Maximum Full load Reverse Current, Full Cycle Average 0.375",(9.5mm) Lead Length Maximum DC Reverse Current at Rated DC Blocking Voltage Ta = 55°C Ta = 25 °C Ta = 150 °C SYMBOL VRRM VRMS VDC IF(AV) IFSM VF IR(AV) IR IR(H) Trr RGP 10A 50 35 50 RGP 10B 100 70 100 RGP 10D 200 140 200 RGP 10G 400 280 400 1.0 30 1.3 100 5.0 200 RGP 10J 600 420 600 RGP 10K 800 560 800 RGP 10M 1000 700 1000 UNIT V V V A A V µA µA µA 250 500 ns pf Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance ( Note 3 ) Junction Temperature Range Storage Temperature Range 150 15 50 - 65 to + 175 - 65 to + 175 CJ RθJA TJ TSTG °C/W °C °C Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC ( 3 ) Thermal Resistance from Junction to Ambient at 0.375" (9.5mm) Lead Lengths, P.C. Board Mounted. Page 1 of 2 Rev. 02 : March 25, 2005 R ATING AND CHARACTERISTIC CURVES ( RGP10A - RGP10M ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω + 0.5 D.U.T. 50 Vdc (approx.) 1Ω PULSE GENERATOR ( NOTE 2 ) O SCILLOSCOPE ( NOTE 1 ) 0 - 0.25 Trr + - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. 1 FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 1.0 30 FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 0.8 24 0.6 TJ = 2 5 °C 0.4 18 12 8.3 ms SINGLE HALF SINE-WAVE (JEDEC) METHOD 0.2 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTHS 0 0 25 50 75 100 125 150 175 6 TJ = TJ m ax. 0 1 2 4 6 10 20 40 60 100 AMBIENT TEMPERATURE, ( °C) FIG.4 - TYPICAL FORWARD CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES 10 Pulse W idth = 300 µs 2% Duty Cycle TJ = 2 5 °C 1.0 10 NUMBER OF CYCLES AT 60Hz FIG.5 - TYPICAL REVERSE CHARACTERISTICS TJ = 1 00 °C 1.0 0.1 0.1 TJ = 2 5 °C 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.01 0 20 40 60 80 100 120 140 FORWARD VOLTAGE, VOLTS PERCENT OF RATED REVERSE VOLTAGE, (%) P age 2 of 2 R ev. 02 : March 25, 2005