SE5D

SE5A - SE5M PRV : 50 - 1000 Volts Io : 5.0 Amperes FEATURES : * * * * * * High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency SURFACE MOUNT HIGH EFFICIENT RECTIFIERS SMC (DO-214AB) 0.0 60(1.52) 0.0 30(0.76) 0.3 05(7.75) 0.320(8.13) 0.280(7.11) 0.260(6.60) 0.008(0.203) 0.004(0.102) 0.121(3.07) 0.115(2.92) 0.2 45(6.22) 0.2 20(5.59) 0.10 3(2.62 ) 0.07 9(2.00 ) 0.012(0.305) 0.006(0.152) MECHANICAL DATA : * * * * * * Case : SMC Molded plastic Epoxy : UL94V-O rate flame retardant Lead : Lead Formed for Surface Mount Polarity : Color band denotes cathode end Mounting position : Any Weight : 0.21 gram Dimensions in inches and (millimeter) Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS RATING Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Current Ta = 55 °C Maximum Peak Forward Surge Current, 8.3ms Single half sine wave superimposed on rated load (JEDEC Method) Maximum Forward Voltage at IF = 5.0 A Maximum DC Reverse Current at Rated DC Blocking Voltage Ta = 25 °C Ta = 100 °C SYMBOL SE5A SE5B SE5D SE5E SE5G SE5J SE5K SE5M UNIT VRRM VRMS VDC IF(AV) IFSM VF IR IR(H) Trr 50 35 50 100 70 100 200 140 200 300 210 300 5.0 200 400 280 400 600 420 600 800 560 800 1000 700 1000 V V V A A 1.1 10 50 50 50 - 65 to + 150 - 65 to + 150 1.7 V µA µA Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Junction Temperature Range Storage Temperature Range 75 ns pf °C °C CJ TJ TSTG Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC Page 1 of 2 Rev. 01 : January 10, 2004 RATING AND CHARACTERISTIC CURVES ( SE5A - SE5M ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω + 0.5 A D.U.T. 50 Vdc (approx) 1Ω 0 - 0.25 A Trr + PULSE GENERATOR ( NOTE 2 ) OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 25-35 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. 1 cm FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT AVERAGE FORWARD OUTPUT CURRENT, AMPERES 5 200 FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES 8.3 ms SINGLE HALF SINE WAVE Ta = 50 °C 160 4 3 120 2 80 1 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 175 40 0 1 2 4 6 10 20 40 60 100 AMBIENT TEMPERATURE, ( °C) NUMBER OF CYCLES AT 60Hz FIG.4 - TYPICAL FORWARD CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FIG.5 - TYPICAL REVERSE CHARACTERISTICS 100 10 TJ = 100 °C FORWARD CURRENT, AMPERES Pulse Width = 300 µs 2% Duty Cycle TJ = 25 °C 10 1.0 SE5A - SE5G 1.0 SE5J - SE5M 0.1 TJ = 25 °C 0.1 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE, VOLTS Page 2 of 2 Rev. 01 : January 10, 2004