APA151

Duct Smoke Detector Accessories Expand the versatility of the Innovair™ line of duct smoke detectors with System Sensor notification and test accessories. Available Accessories APA151 MHR MHW PS24LO PS24LOW PS12/24SLENSW RA400Z RTS451 RTS451KEY SSK451 Piezo Annunciator Mini-Horn, Red Mini-Horn, White Mini-Alert Add-on Strobe (red) Mini-Alert Add-on Strobe (white) Wall-Mount “SMOKE” Lens Remote Annunciator Remote Test Station Remote Test Station with Key Multi-Signaling Accessory These products add functionality to the duct detection system by allowing quick, convenient inspections at eye level and effective audible and visible notification options. All System Sensor duct detectors and accessories are UL listed. The APA151 piezo annunciator, which replaces the APA451 with a new, improved look, provides an audible alarm signal, a red LED to indicate alarm status, and a green LED to indicate power status. It is intended for use with System Sensor 4-wire conventional duct smoke detector applications without a system control panel, to comply with NFPA 90A. The MHR and MHW SpectrAlert® Advance mini-horns feature temporal or continuous tones at high and low volume settings. These horns are ideal for applications, where a small notification device is desired. Their small footprint allows mounting to single gang back boxes for aesthetically sensitive applications. The PS24LO and PS24LOW mini alert add-on strobes can be attached to the SSK451 multi-signaling accessory for visual alarm signaling. The PS12/24SLENSW “SMOKE” lens is available to meet special code requirements in certain jurisdictions. The RA400Z remote annunciator is designed for both conventional and intelligent applications. The red LED provides visual indication of an alarm condition. The RTS451 and RTS451KEY remote test stations are automatic fire detector accessories designed to test duct detectors from a more convenient location. For 4-wire detectors, the RTS451KEY test station features a multi-colored LED that alternates between steady green and red. For 2-wire detectors, the LED illuminates red for alarm. The SSK451 multi-signaling accessory is designed to work with System Sensor 4-wire conventional duct smoke detectors. It combines a horn feature with the key-activated test and reset functions. Green, amber, and red LEDs indicate power, trouble, and alarm conditions, respectively. Agency Listings Specifications, Duct Smoke Detector Accessories APA151 Piezo Annunciator Voltage Regulated 24 VDC Operating Voltage 16 to 33 VDC Maximum Alarm Current 30 mA Temperature Range 0°C to 49°C (32°F to 120°F) Relative Humidity 10 to 93% non-condensing Wire Gauge 12 to 18 AWG Dimensions 4.6 in H × 2.9 in W × .45 in D MHR/MHW SpectrAlert® Advance Mini-Horns Voltage Regulated 12 DC or FWR (Full Wave Rectified) or Regulated 24VDC or FWR Operating Voltage 8 to 33 VDC (9 to 33 VDC with Sync•Circuit™ Module) Sounder Current Draw 22 mA RMS max at 8 to 17.5 Volts DC 17 mA RMS max at 8 to 17.5 Volts FWR 29 mA RMS max at 16 to 33 Volts DC 25 mA RMS max at 16 to 33 Volts FWR Temperature Range 0°C to 49°C (32°F to 120°F) Humidity Range 10 to 93% non-condensing Nominal Sounder Frequency 3 kHz Wire Gauge 12 to 18 AWG Dimensions 4.6 in H × 2.9 in W × 0.45 in D PS24LO/PS24LOW Mini-Alert™ Add-on Strobes Voltage 24 VDC Temperature Range 0°C to 49°C (32°F to 120°F) Wire Gauge 12 to 18 AWG Dimensions 3.8 in H × 1.6 in W × 1.6 in D RA400Z Remote Annunciator Voltage Range Conventional System: 3.1 to 32 VDC Intelligent System: 18 to 32 VDC Maximum Alarm Current 10 mA Dimensions 4.6 in H × 2.8 in W × 1.3 in D RTS451 Remote Test Station Power Requirements Alarm LED: 2.8 to 32 VDC, 7.5 mA max. Total Current: 105 mA max. Test Switch 10 VA @ 32 VDC Reset Switch 10 VA @ 32 VDC Alarm Response Time 40 seconds max. Temperature Range –10°C to 60°C (14°F to 140°F) Relative Humidity 95% non-condensing Wire Gauge 14 to 18AWG Dimensions 4.6 in H × 2.75 in W × 1.8 in D RTS451KEY Remote Test Station with Key Power Requirements Power LED (Green): 14 to 35 VDC, 12 mA max. Alarm LED (Red): 2.8 to 32 VDC, 7.5 mA max. Total Current: 103 mA maximum Alarm Response Time 40 seconds maximum Temperature Range –10°C to 60°C (14°F to 140°F) Relative Humidity 95% non-condensing Wire Gauge 14 to 18 AWG Dimensions 4.6 in H × 2.75 in W × 1.8 in D SSK451 Multi-signaling Accessory Voltage 24 VDC Power Requirements Standby: 8 mA Trouble: 16 mA Alarm without strobe: 40 mA Alarm with strobe: 65 mA Sounder 87 dBA at ten feet Temperature Range –10°C to 60°C (14°F to 140°F) Relative Humidity 95% non-condensing Wire Gauge 14 to 22 AWG Dimensions 4.8 in H × 4.7 in W × 1.5 in D For the very latest product specifications and listing information, please visit the System Sensor web site at www.systemsensor.com. RTS451 UL S4011 RTS451KEY UL S2522 APA151 UL S4011 SSK451 UL S2522 RA400Z UL S2522 MHW UL S4011 MHR UL S4011 SSK451 with PS24LOW strobe and PS12/24 LENSW lens ©2008 System Sensor. Product specifications subject to change without notice. Visit systemsensor.com for current product information, including the latest version of this data sheet. A05-0375-003 • 6/08 • #1991 3825 Ohio Avenue • St. Charles, IL 60174 Phone: 800-SENSOR2 • Fax: 630-377-6495