RC2010J103-XX-BL

THICK FILM CHIP RESISTOR GENERAL PURPOSE RC2010 Thick Film Chip Resistor – General Purpose Features • • • • Small and light weight Excellent heat resistance and moisture resistance Suitable size and packaging for surface mount assembly RoHS Compliant Applications • For general purpose applications • For laptop and notebook computer, memory module, digital camera and telecommunication equipment Absolute Maximum Ratings & Characteristics Product Number mm Tolerance Power Rating @70˚C MAX MAX Working Overload TCR ppm/℃ Voltage Voltage ±200 RC2010 5025 J: ±5% F: ±1% 3/4W 200V 400V ±100 ±200 Resistance Range Rated Working Temperature 1Ω ~ 9.76Ω 10Ω ~ 1MΩ 1.02MΩ ~ 10MΩ -55℃~+155℃ *Jumper Product Number RC2010 Jumper Rated Current 3.5A Resistance 50mΩ (max.) Rated Working Temperature -55℃~+155℃ TAITRON COMPONENTS INCORPORATED www.taitroncomponents.com Tel: (800)-TAITRON Fax: (800)-TAITFAX (800)-824-8766 (800)-824-8329 (661)-257-6060 (661)-257-6415 Rev. C/JJ 2007-08-10 Page 1 of 7 Thick Film Chip Resistor – General Purpose RC2010 Power Derating Curve For resistors operate in the ambient temperature over 70˚C, loading power ratio will de-rate in accordance with following curve. Percentage of the rated dissipation (%) Ambient Temperature (℃) Max. Dissipation of rated power as a function of the ambient temperature Soldering Condition IR Reflow soldering Wave soldering (flow soldering) Rev. C/JJ 2007-08-10 www.taitroncomponents.com Page 2 of 7 Thick Film Chip Resistor – General Purpose RC2010 Dimensions (in mm) Product Number RC2010 mm 5025 L 5.00 ± 0.20 W 2.50± 0.15 H 0.55 ± 0.10 A 0.60 ± 0.25 B 0.50 ± 0.20 Average Weight 23.887 mg Marking (1) ±5% Tolerance (J): 3 digits, the first two digits are significant figures; the third digit is number of zeros to follow. Letter “R” is as decimal point; Letter “0” for jumper. (2) ±1% Tolerance (F): 4 digits, the first three digits are significant figures; the fourth digit is number of zeros. Letter “R” is as decimal point; Letter “0” for jumper. Examples: 3 digits marking (±5%) 4 digits marking (±1%) 683 = 68x103 Ω = 68000 Ω = 68KΩ 7R5 = 7.5 Ω Jumper 6812 = 681x102Ω = 68100 Ω = 68.1KΩ Rev. C/JJ 2007-08-10 www.taitroncomponents.com Page 3 of 7 Thick Film Chip Resistor – General Purpose RC2010 Test and Requirements Test Item Temperature Coefficient of Resistance(T.C.R.) Short Time Overload Insulation Resistance Voltage Proof Substrate Bending Test Resistance to soldering heat Leaching Solderability Endurance at upper category temperature Rapid change of temperature Damp heat with load Test Method JIS C 5201 4.8 IEC 60115-1 4.8 JIS C 5201 4.13 IEC 60115-1 4.13 JIS C 5201 4.6 IEC 60115-1 4.6 JIS C 5201 4.7 IEC 60115-1 4.7 JIS C 5201 4.33 IEC 60115-1 4.33 JIS C 5201 4.18 IEC 60115 4.18 JIS C 5201 4.18 IEC 60115 4.18 JIS C 5201 4.17 IEC 60115-1 4.17 JIS C 5201 4.23 IEC 60115-1 2.23.2 JIS C 5201 4.19 IEC 60115-1 4.19 Test Condition -55°C~+155,20°C is the reference temperature 2.5 times RCWV or max. overload voltage for 5 seconds Max. overload voltage for 1 minute 1.42 times RCWV (RMS) for 1 minute Bending once with 5 seconds for 3 mm 260±5°C for 10 seconds 260±5°C for 60 seconds 245±5°C for 3 seconds. at +155°C for 1000 hrs -55°C to +155°C, 5 cycles 40±2°C, 90~95% R.H. or max. working voltage for 1000 hrs with 1.5hrs “ON” and 0.5 hrs “OFF” 70±2°C, RCWV or Max. working voltage for 1000 hrs with 1.5 hrs “ON” and 0.5 hrs “OFF” Requirement ±1% Within the specification ±(1.0%+0.05Ω) ±(2.0%+0.05Ω) ≥10G no breakdown or flashover ±(1.0%+0.05Ω) ±(0.5%+0.05Ω) no leaching >95% coverage ±(1.0%+0.05Ω) ±(0.5%+0.05Ω) ±(1.5%+0.10Ω) ±(1.0%+0.05Ω)