Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products. REMINDERS
■ Product information in this catalog is as of October 2009. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. ■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. ■ Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. ■ All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. ■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu“ tors (so called TAIYO YUDEN’ official sales channel” s ). It is only applicable to the products purchased from any of TAIYO YUDEN’ of ficial sales channel. s ■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. ■ Caution for export Certain items in this catalog may require specific procedures for export according to“Foreign Exchange and Foreign Trade Control Law”of Japan,“U.S. Export Administration Regulations” and other applicable regulations. , Should you have any question or inquiry on this matter, please contact our sales staff. Should you have any question or inquiry on this matter, please contact our sales staff.
1
notice_e-01
CHIP ANTENNA
REFLOW
■ FEATURES
◦ ompact and Low-profile C ◦ ide bandwidth and High Gain W ◦ table temperature characteristics S
■ APPLICATIONS
◦ luetooth®, Wireless LAN, GPS, WiMAX, ZigBee, UWB B
■ ORDERING CODE
A
❶
AH AF
F
△
❷
2
1
❸
6
M
❹
F M
2
4
❺
example
5
0
0
❻
1
ーT
-
❼
T
❶Type Multilayer Antenna Helical Antenna
❷Electrode Code △ With Plating
△=Blank space
❸Dimensions (case size) mm] [ 216 2.5×1.6 816 8.0×1.6 116 11.0×1.6 316 3.2×1.6 083 8.0×3.0 104 10.0×4.0 122 12.0×2.0 086 8.0×6.0
❹Special Code Inverted F Mono Pole Mono Pole N (Dual)
❺Frequency MHz] [ 1575 2450 5550 1574.397~1576.443 2400~2500 3100~8000
❼Packaging Tape & Reel
1. Describe Center Frequency 2. Lower Frequency for Dualband
❻Spec Code 01~ S1~ Applicable to AH104F
■ E XTERNAL DIMENSIONS/STANDARD QUANTITY
AF 216M Type, AF 816M Type, AF 116M Type AH 316M Type AH 083F Type AH 104F Type
E
AH 122F Type
AH 104N Type
AH 086M Type
Type AF 216M AF 816M AF 116M AH 316M AH 083F AH 104F AH 122F AH 104N AH 086M
L 2.5±0.2 8±0. 2 11±0.2 3. 2±0.15 8±0.3 10±0.3 12±0.3 10±0.3 8±0.3
W 1.6±0.2 1.6±0.2 1.6±0.2 1.6±0.15 3±0.3 4±0.3 2±0.3 4±0.3 6±0.3
T 1.6±0.2 1.6±0.2 1.6±0.2 0.5±0.1 1±0.3 1±0.3 0.95±0.3 1±0.3 1±0.3
E 0.5±0.3 0.5±0.3 0.5±0.3 0.5±0.2 ー ー ー ー ー
a ー ー ー ー 3.1±0.3 2.5±0.3 5.1±0.3 3±0.3 1.8±0.2
b ー ー ー 1.0 min. 1±0.3 1±0.3 1±0.3 0.8±0.3 1±0.3
c ー ー ー ー 1.15±0.3 1±0.3 3.1±0.3 1.5±0.3 ー
Standard Quantity (pcs) Embossed Tape 2000 30 00 1000 2000 1000
Unit : mm (inch)
■ PART NUMBERS
Applications GPS Ordering Code AF816M157502 AF116M157502 AH316M157501 AF216M245001 AH316M245001 AH083F245001 AH104F2450S1 AH104F2650S1 AH122F245001 AH104N2450D1 AH086M555001 AH086M555003 External Dimensions (mm) 8.0×1.6×1.6 11.0×1.6×1.6 3.2×1.6×0.5 2.5×1.6×1.6 3.2×1.6×0.5 8.0×3.0×1.0 10.0×4.0×1.0 10.0×4.0×1.0 12.0×2.0×0.95 10.0×4.0×1.0 8.0×6.0×1.0 8.0×6.0×1.0 Center Frequency (MHz) 1575 1575 1575 2450 2450 2450 2450 2650 2450 2450/5400 5550 5550
W-LAN (2.4GHz) Bluetooth® WiMAX (2.5GHz) ZigBee W-LAN (2.4GHz/5GHz) UWB & WiMAX (3.5GHz)
* T his catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
148
1
chipantenna01_e-01
■ ELECTRICAL CHARACTERISTICS TYPICAL CHARACTERISTICS ・
Typical Characteristics on Taiyo Yuden evaluation board
●AF 816M157502
11
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+Y
+X
−Y
Bandwidth: 180MHz (VSWR: less than 2)
+X
−X
+Z
−Y
Vertical polarization
+Y
Vertical polarization
1.325
1.575
1.825
−Z
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of VSWR
Typical characteristics of radiation pattern @1.575GHz) (
●AH 116M157502
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+X
HIGH FREQUENCY DIELECTRIC COMPONENT
+Y
Bandwidth:125MHz (VSWR:less than2)
−Y
+X
−X
+Z
Vertical polarization
−Y
+Y
Vertical polarization
1.325
1.575
1.825
−Z
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of VSWR
Typical characteristics of radiation pattern @1.575GHz) (
●AH 316M157501
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+Y
+X
−Y
Bandwidth: 90MHz (VSWR: less than 2)
+X
−X
+Z
Vertical polarization
−Y
+Y
Vertical polarization
1.325
1.575
1.825
−Z
Typical characteristics of VSWR
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of radiation pattern @1.575GHz) (
●AF 216M245001
ZX-Plane +Z
+X −Z
+Y −Y
XY-Plane
−X
+X
440MHz
+X
−X
+Z
−Y
+Y
Vertical polarization
Vertical polarization
−Z
Typical characteristics of VSWR
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of radiation pattern @2.45GHz) (
●AH 316M245001
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+X
+Y
−Y
Bandwidth: more 190MHz Bandwidth: than 170MHz (VSWR: less than 2)
+X
−X
+Z
Vertical polarization
−Y
+Y
Vertical polarization
2.0
2.5
3.0
−Z
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of VSWR
Typical characteristics of radiation pattern @2.45GHz) (
* T his catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipantenna01_e-01
1
149
■ ELECTRICAL CHARACTERISTICS TYPICAL CHARACTERISTICS ・
Typical Characteristics on Taiyo Yuden evaluation board
●AH 083F245001
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+Y
+X
−Y
Bandwidth:150MHz 2
+X
−X
+Z
Vertical polarization
−Y
+Y
Vertical polarization
−Z
Typical characteristics of VSWR
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of radiation pattern @2.45GHz) (
●AH 104F2450S1
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+Y
+X
−Y
300MHz
+X
−X
+Z
Vertical polarization
−Y
+Y
Vertical polarization
−Z
Typical characteristics of VSWR
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of radiation pattern @2.45GHz) (
●AH 122F245001
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+Y
+X
−Y
150MHz 2
+X
−X
+Z
Vertical polarization
−Y
+Y
Vertical polarization
−Z
Typical characteristics of VSWR
Horizontal polarization
+X
Horizontal polarization
( Typical characteristics of radiation pattern @2.45GHz)
●AH 104N2450D1
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+Y
+X
−Y
Bandwidth:500MHz
+X
−X
+Z
Vertical polarization
−Y
+Y
Vertical polarization
−Z
Typical characteristics of VSWR(2GHz band)
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of radiation pattern @2.45GHz) (
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+Y
+X
−Y
Bandwidth:1200MHz
+X
−X
+Z
Vertical polarization
−Y
+Y
Vertical polarization
4.9
5.4
5.9
−Z
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of VSWR(5GHz band)
Typical characteristics of radiation pattern @5.25GHz) (
* T his catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
150
1
chipantenna01_e-01
■ ELECTRICAL CHARACTERISTICS・ TYPICAL CHARACTERISTICS
Typical Characteristics on Taiyo Yuden evaluation board
●AH 086M555001
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+Y
+X
−Y
+X
−X
+Z
Vertical polarization
−Y
+Y
Vertical polarization
2
3
4
5
6
7
8
9
10
−Z
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of VSWR
Typical characteristics of radiation pattern @3.96GHz) (
●AH 086M555003
ZX-Plane
+Z
+X −Z
XY-Plane
−X
+Y
+X
HIGH FREQUENCY DIELECTRIC COMPONENT
−Y
+X
−X +Z
Vertical polarization
−Y
+Y
Vertical polarization
2
3
4
5
6
7
8
9
10
−Z
Typical characteristics of VSWR
Horizontal polarization
+X
Horizontal polarization
Typical characteristics of radiation pattern @3.96GHz) (
* T his catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipantenna01_e-01
1
151
■ PACKAGING
①Minimum Quantity
Type AF216M, AF816M, AF116M, AH104F, AH122F, AH104N AH316M AH083F, AH086M Standard Quantity (pcs) Embossed Tape 20 00 3000 10 00
④Leader and Blank Portion
②Tape Material
⑤Reel size
Type AF216M AH316M AF816M AH083F AF116M, AH104F AH122F, AH104N AH 086M
A 178±2.0 (7.0±0.08) 178±2.0 (7.0±0.08) 330±2.0 (13.0±0.08) 330 ± 2.0 (13.0±0.08)
B 50 min. (2.0 min.) 50 min. (2.0 min.) 100±1.0 (3.94±0.04) 10 0 ± 1.0 (3.94±0.04)
W 10.0±1.5 (0.394±0.06) 17.0±1.0 (0.67±0.04) 25.5±1.0 (1.0±0.04) 17.0 ± 1.0 (0.67±0.04)
T 3.0 max. (0.12 max.) 2.5 max. (0.1 max.) 3.0 max. (0.12 max.) 2.5 max. (0.1 max.)
Unit : mm (inch)
③Taping Dimensions ◦Embossed Tape
⑥Top Tape Strength
The top tape requires a peel-off force of 0.1~0.7N in the direction of the arrow as illustrated below.
Type AF216M AF816M AF116M AH316M AH083F AH104F, AH104N AH122F AH086M
Chip Cavity A 1.85±0.2 (0.073±0.008) 1.95±0.2 (0.077±0.008) 1.95±0.2 (0.077±0.008) 1.9±0.2 (0.075±0.008) 3.35±0.2 (0.132±0.008) 4.35±0.2 (0.171±0.008) 2.3±0.2 (0.091±0.008) 6.25±0.2 (0.246±0.008) B 2.75±0.2 (0.108±0.008) 8.4±0.2 (0.331±0.008) 11.4±0.2 (0.449±0.008) 3.5±0.2 (0.138±0.008) 8.35±0.2 (0.329±0.008) 10.35±0.2 (0.407±0.008) 12.3±0.2 (0.484±0.008) 8.26±0.2 (0.325±0.008) C
Tape Widthness D 3.5±0.1 (0.138±0.004) 7.5±0.1 (0.296±0.004) 11.5±0.1 (0.453±0.004) 3.5±0.1 (0.138±0.004) 7.5±0.1 (0.295±0.004) 11.5±0.1 (0.435±0.004) 11.5±0.1 (0.435±0.004) 7.5±0.1 (0.296±0.004) 8±0.2 (0.315±0.008) 16±0.3 (0.630±0.012) 24±0.3 (0.945±0.012) 8±0.2 (0.315±0.012) 16±0.3 (0.630±0.012) 24±0.3 (0.945±0.012) 24±0.3 (0.945±0.012) 16±0.3 (0.630±0.012)
Insertion Pitch F 4±0.1 (0.157±0.004) 4±0.1 (0.157±0.004) 4±0.1 (0.157±0.004) 4±0.1 (0.157±0.004) 8±0.1 (0.315±0.004) 8±0.1 (0.315±0.004) 4±0.1 (0.157±0.004) 12±0.1 (0.473±0.004)
Tape Thickness MAX. K T 1.95 (0.077) 2.05 (0.081) 2.05 (0.081) 0.85 (0.033) 1.55 (0.061) 1.55 (0.061) 1.45 (0.057) 1.3 (0.051) 0.3 (0.012) 0.35 (0.014) 0.35 (0.014) 0.3 (0.012) 0.3 (0.012) 0.3 (0.012) 0.35 (0.014) 0.3 (0.012)
Unit : mm (inch)
* T his catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipan_reli_e-01
1
chipan_reli-PRP1
■ RELIABILITY DATA
1. Operating Temperature Range Specified Value 2. Storage Temperature Range Specified Value 【Test Methods and Remarks】 ※with being taped, ー20~+35℃ -20~+80℃
-40~+85℃
3. Solderability Specified Value At least 90% of Terminal surface immersed is covered by new solder. 【Test Methods and Remarks】 Solder temperature : 230±5℃ Duration : 3±1 sec. Preconditioning : Preheating at 150℃ after immersion into flux. 4. Thermal Shock Specified Value Shall satisfy required VSWR value of individual specifications for each item. 【Test Methods and Remarks】 1 hour of recovery after 10 times of 30min.immersion alternately at ー40℃ and 85℃ of temperature,followed by evaluating electrical characteristics. 5. High Temperature Storage Test Specified Value Shall satisfy required VSWR value of individual specifications for each item. 【Test Methods and Remarks】 1 hour of recovery under standard condition after 96 hours recovery with 85℃ of temperature, followed by evaluating electrical characteristics. 6. Low Temperature Storage Test Specified Value Shall satisfy required VSWR value of individual specifications for each item. 【Test Methods and Remarks】 1 hour of recovery under standard condition after 96 hours recovery with ー40℃ of temperature, followed by evaluating electrical characteristics. 7. Humidity Storage Test Specified Value Shall satisfy required VSWR value of individual specifications for each item. 【Test Methods and Remarks】 1 hour of recovery under standard condition after 96 hours recovery with 60℃ of temperature, 90~95% relative humidity followed by evaluating electrical characteristics. 8. Resistance to Reflow Specified Value Shall satisfy required VSWR value of individual specifications for each item. 【Test Methods and Remarks】 Two times of reflow soldering by recommended profile attached, followed by evaluating electrical characteristics.
* T his catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
chipan_reli-PRP2
1
chipan_reli_e-01
■ PRECAUTIONS
Precautions 1. PCB Design ◆Land pattern design Please do not arrange the surface and inside layer pattern near the antenna mounting area. ◆Land pattern design L and pattern dimension examples and recommended antenna land pattern
AF216M/816M/116M
AH316M
Type AF216M AF816M AF116M
L 2.5 8 11
Dimensions P 1.5 7 10
a 3 5 3 Unit : mm
AH083F
AH104F
AH122F
Technical Considerations
AH104N
AH086M
2. Soldering ◆ Conditions of Reflow soldering (for reference) ・Pb Free Reflow Profile ・Reflow Profilev
Technical Considerations ※ Components should be preheated to within 100 to 130℃ from soldering temperature. ※ Assured to be reflow soldering for 2 times. Note : The above profiles are the maximum allowab le soldering condition, therefore these profiles are not always recommended. 3. Storage Conditions ◆Storage conditions 1. The Products should not be used in the following environments : ・exposure to special gases such as (C12, NH3, SOx, NOx) ・exposure to volatile gas or inflammable gas ・exposure to a lot of dust ・exposure to water or condensation Precautions ・exposure to direct sanlight or freezing 2. The Products should be kept in the following conditions : ・Temperature : ー10~+40℃ ・Humidity : 15~85%RH 3. The products should be used within 6 months after delivery. In case of storage over 6 months, solderability shall be checked before actual usage.
■ Please contact our offices for further details of specifications. All of the standard values listed here are subject to change without notice due to technical improvements. Therefore, please check the specifications carefully before use. * T his catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
chipan_reli-PRP3
1
chipan_reli_e-01