AH083F259001-T

for General Electronic Equipment Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product Information in this Catalog Product information in this catalog is as of October 2020. All All of of the the January 2021. contents specified herein and production status of the products listed in this catalog are subject to change without notice due to technical improvement of our products, etc. Therefore, please check for the latest information carefully before practical application or use of our products. (4) Powe r g e n e r atio n c o ntro l e quip m e nt (nu c le a r p owe r, hydroelectric power, thermal power plant control system, etc.) (5) Undersea equipment (submarine repeating equipment, underwater work equipment, etc.) (6) Military equipment (7) Any other equipment requiring extremely high levels of safety and/or reliability equal to the equipment listed above Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. *Notes: 1. There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. 2. Implantable medical devices contain not only internal unit which is implanted in a body, but also external unit which is connected to the internal unit. ■ Approval of Product Specifications Ple a se c ont ac t TA IYO YUD EN for fur the r det a ils of p ro duc t specifications as the individual product specification sheets are available. When using our products, please be sure to approve our product specifications or make a written agreement on the product specification with TAIYO YUDEN in advance. ■ Pre-Evaluation in the Actual Equipment and Conditions Please conduct validation and verification of our products in actual conditions of mounting and operating environment before using our products. ■ Limited Application 1. Equipment Intended for Use The products listed in this catalog are intended for generalpurpose and standard use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC) and other equipment specified in this catalog or the individual product specification sheets. TAIYO YUDEN has the line-up of the products intended for use in automotive electronic equipment, telecommunications infrastructure and industrial equipment, or medical devices classified as GHTF Classes A to C (Japan Classes I to III). Therefore, when using our products for these equipment, please check available applications specified in this catalog or the individual product specification sheets and use the corresponding products. 2. Equipment Requiring Inquiry Please be sure to contact TAIYO YUDEN for further information before using the products listed in this catalog for the following equipment (excluding intended equipment as specified in this catalog or the individual product specification sheets) which may cause loss of human life, bodily injury, serious property damage and/or serious public impact due to a failure or defect of the products and/or malfunction attributed thereto. (1) Transportation equipment (automotive powertrain control system, train control system, and ship control system, etc.) (2) Traffic signal equipment (3) Disaster prevention equipment, crime prevention equipment (4) Medical devices classified as GHTF Class C (Japan Class III) (5) H i g h l y p u b l i c i n f o r m a t i o n n e t wo r k e q u i p m e n t , d a t a processing equipment (telephone exchange, and base station, etc.) (6) Any other equipment requiring high levels of quality and/or reliability equal to the equipment listed above 3. Equipment Prohibited for Use Please do not incorporate our products into the following equipment requiring extremely high levels of safety and/or reliability. (1) Aerospace equipment (artificial satellite, rocket, etc.) (2) Aviation equipment *1 (3) Medical devices classified as GHTF Class D (Japan Class IV), implantable medical devices *2 4. Limitation of Liability Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment that is not intended for use by TAIYO YUDEN, or any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Safety Design When using our products for high safety and/or reliability-required equipment or circuits, please fully perform safety and/or reliability evaluation. In addition, please install (i) systems equipped with a protection circuit and a protection device and/or (ii) systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault for a failsafe design to ensure safety. ■ Intellectual Property Rights Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Limited Warranty Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a failure or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ TAIYO YUDEN’s Official Sales Channel The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter “TAIYO YUDEN’ s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’ s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export Administration Regulations”,“Foreign Exchange and Foreign Trade Control Law” of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 2 21 for General Electronic Equipment CHIP ANTENNAS CHIP ANTENNAS REFLOW ■PARTS NUMBER A H △ ② ① ３ 1 6 ③ M ④ ①Series name Code AH 2 4 5 0 0 1 ⑤ - ⑥ T ④Special code Code F M N Series name Multilayer antenna ②Electrode code Code △ Electrode code With plating ③Dimensions（case size） Code 168 316 083 104 086 △＝Blank space ⑦ Special code Inverted F Mono pole Mono pole（Dual） ⑤Frequency Code Frequency［MHz］ （example） 1575 1574.397～1576.443 2450 2400～2500 5550 3100～8000 1.Describe Center Frequency 2.Lower Frequency for Dual band Dimensions（case size）［mm］ 1.6×0.8 3.2×1.6 8.0×3.0 10.0×4.0 8.0×6.0 HIGH FREQUENCY PRODUCTS ⑥Spec code Code 01～ S1～ Applicable to AH 104F ⑦Packaging Code -T Packaging Taping Spec code ■EXTERNAL DIMENSIONS / STANDARD QUANTITY AH 168M type, AH 316M type AH 083F type Direction mark Direction mark L AH 104F type Feed mark L Direction mark W W E b AH 104N type T b c b b c a b c b a c b b a a AH 086M type Feed mark Direction mark W T T b Feed mark L Direction mark W W L Feed mark L T T b AH AH AH AH AH AH Type 168M 316M 083F 104F 104N 086M b c b c b b a ｂ a L 1.6±0.1 3.2±0.15 8±0.3 10±0.3 10±0.3 8±0.3 W 0.8±0.1 1.6±0.15 3±0.3 4±0.3 4±0.3 6±0.3 T 0.65 Max 0.5±0.1 1±0.3 1±0.3 1±0.3 1±0.3 ｂ a ｂ a E 0.3±0.1 0.5±0.2 - a 3.1±0.3 2.5±0.3 3±0.3 1.8±0.2 b 0.6±0.1 1.0min. 1±0.3 1±0.3 0.8±0.3 1±0.3 c 1.15±0.3 1±0.3 1.5±0.3 - Standard quantity［pcs］ 5000 3000 1000 2000 2000 1000 Unit：mm ■PARTS NUMBER Applications GPS W-LAN（2.4GHｚ） Bluetooth® WiMAX（2.5GHｚ） ZigBee W-LAN（2.4GHｚ/5GHｚ） UWB & WiMAX（3.5GHz） Part number AH 316M157501 AH 168M245001 AH 316M245001 AH 083F245001 AH 104F2450S1 AH 104F2650S1 AH 104N2450D1 AH 086M555003 External dimensions（L×W×T）［mm］ 3.2×1.6×0.5 1.68×0.8×0.65 Max. 3.2×1.6×0.5 8.0×3.0×1.0 10.0×4.0×1.0 10.0×4.0×1.0 10.0×4.0×1.0 8.0×6.0×1.0 Center frequency［MHｚ］ 1575 2450 2450 2450 2450 2650 2450/5400 5550 chipantenna_e-E09R01.doc ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 110 21 for General Electronic Equipment ■ELECTRICAL CHARACTERISTICS / TYPICAL CHARACTERISTICS Typical characteristics on TAIYO YUDEN evaluation board ●AH 316M157501 Typical characteristics of VSWR Typical characteristics of radiation pattern （@1.575GHz） VSWR ●AH 168M245001 11 10 9 8 7 6 5 4 3 2 1 Bandwidth : 300MHz ( VSWR : less than2 ) 2.0 2.5 Typical characteristics of VSWR 3.0 HIGH FREQUENCY PRODUCTS Frequency [GHz] Typical characteristics of radiation pattern （@2.45GHz） ●AH 316M245001 Typical characteristics of VSWR Typical characteristics of radiation pattern （@2.45GHz） ●AH 083F245001 Typical characteristics of VSWR Typical characteristics of radiation pattern （@2.45GHz） chipantenna_e-E09R01.xls ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 21 111 for General Electronic Equipment ■ELECTRICAL CHARACTERISTICS / TYPICAL CHARACTERISTICS Typical characteristics on TAIYO YUDEN evaluation board ●AH 104F2450S1 Typical characteristics of VSWR Typical characteristics of radiation pattern （@2.45GHz） ●AH 104N2450D1 HIGH FREQUENCY PRODUCTS Typical characteristics of VSWR（2GHz band） Typical characteristics of radiation pattern （@2.45GHz） Typical characteristics of VSWR（5GHz band） Typical characteristics of radiation pattern （@5.25GHz） ●AH 086M555003 Typical characteristics of VSWR Typical characteristics of radiation pattern （@3.96GHz） chipantenna_e-E09R01.xls ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 112 21 CHIP ANTENNAS ■PACKAGING ①Minimum Quantity Standard Quantity (pcs) Embossed Tape 2000 3000 1000 5000 Type AH104F, AH104N AH316M AH083F, AH086M AH168M ②Tape Material ●Embossed Tape ●Card Board Cattier Tape Top tape Top tape Base tape Sprocket hole Sprocket hole Bottom tape Chip cavity Base tape Chip cavity Insertion Pitch F 4±0.1 （0.157±0.004） 8±0.1 （0.315±0.004） 8±0.1 （0.315±0.004） 12±0.1 （0.473±0.004） Tape Thickness max. K T 0.85 0.3 （0.033） （0.012） 1.45 0.3 （0.061） （0.012） 1.45 0.3 （0.061） （0.012） 1.3 0.3 （0.051） （0.012） Unit：mm （inch） Chip Filled Chip ③Taping Dimensions ●Embossed Tape Sprocket hole Unit：mm（inch） φ1.5＋0.1/－0 (φ0.059＋0.004/-0) A 1.75±0.1 (0.069±0.004） T D C B K F 2.0±0.1 (0.079±0.004) Type AH316M AH083F AH104F, AH104N AH086M 4.0±0.1 (0.157±0.004) Chip Cavity A B 1.9±0.2 3.5±0.2 （0.075±0.008） （0.138±0.008） 3.35±0.2 8.35±0.2 （0.132±0.008） （0.329±0.008） 4.35±0.2 10.35±0.2 （0.171±0.008） （0.407±0.008） 6.25±0.2 8.26±0.2 （0.246±0.008） （0.325±0.008） Tape Widthness C D 8±0.2 3.5±0.1 （0.315±0.008） （0.138±0.004） 16±0.3 7.5±0.1 （0.630±0.012） （0.295±0.004） 24±0.3 11.5±0.1 （0.945±0.012） （0.435±0.004） 16±0.3 7.5±0.1 （0.630±0.012） （0.296±0.004） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipantenna_pack_e-E09R01 ●Paper tape 0.315 inches wide Unit：mm（inch） A B T 8.0±0.3 (0.315±0.012) 3.5±0.05 (0.138±0.002) Sprocket hole F 1.75±0.1 (0.069±0.004） φ1.5＋0.1/－0 (φ0.059＋0.004/-0) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) Type AH168M Chip cavity Ａ Ｂ 0.95±0.05 1.80±0.05 （0.037±0.002） （0.071±0.002） Insertion Pitch Ｆ 4.0±0.1 （0.157±0.004） Tape Thickness max. T 0.80 （0.031） Unit：mm（inch） W 10.0±1.5 （0.394±0.06） 17.0±1.0 （0.67±0.04） 25.5±1.0 （1.0±0.04） 17.0±1.0 （0.67±0.04） T 3.0 max. （0.12 max.） 2.5 max. （0.1 max.） 3.0 max. （0.12 max.） 2.5 max. （0.1 max.） Unit：mm（inch） ④Leader and Blank Portion ⑤Reel size Type AH168M AH316M AH083F AH104F AH104N AH086M A 178±2.0 （7.0±0.08） 178±2.0 （7.0±0.08） 330±2.0 （13.0±0.08） 330±2.0 （13.0±0.08） B 50 min. （2.0 min.） 50 min. （2.0 min.） 100±1.0 （3.94±0.04） 100±1.0 （3.94±0.04） ⑥Top Tape Strength The top tape requires a peel-off force of 0.1～0.7N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipantenna_pack_e-E09R01 CHIP ANTENNAS ■RELIABILITY DATA 1. Operating Temperature Range Specified Value －40～＋85℃ 2. Storage Temperature Range Specified Value －40～＋85℃ Test Methods and Remarks ※with being taped, －20～＋40℃ 3. Solderability Specified Value At least 75% of immersed terminal surface is covered by new solder. Test Methods and Remarks Solder temperature Duration Preconditioning : 240±5℃ : 3±1 sec. : Preheating at 150℃ after immersion into flux. 4. Thermal Shock Specified Value Shall satisfy required VSWR value of individual specifications for each item. Test Methods and Remarks 1 hour of recovery after 10 times of 30min.immersion alternately at －40℃ and 85℃ of temperature, followed by evaluating electrical characteristics. 5. High Temperature Storage Test Specified Value Shall satisfy required VSWR value of individual specifications for each item. Test Methods and Remarks 1 hour of recovery under standard condition after 96 hours recovery with 85℃ of temperature, followed by evaluating electrical characteristics. 6. Low Temperature Storage Test Specified Value Shall satisfy required VSWR value of individual specifications for each item. Test Methods and Remarks 1 hour of recovery under standard condition after 96 hours recovery with －40℃ of temperature, followed by evaluating electrical characteristics. 7. Humidity Storage Test Specified Value Shall satisfy required VSWR value of individual specifications for each item. Test Methods and Remarks 1 hour of recovery under standard condition after 96 hours recovery with 60℃ of temperature, 90～95% relative humidity followed by evaluating electrical characteristics. 8. Resistance to Reflow Specified Value Shall satisfy required VSWR value of individual specifications for each item. Test Methods and Remarks Two times of reflow soldering by recommended profile attached, followed by evaluating electrical characteristics. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipantenna_reli_e-E09R01 CHIP ANTENNAS ■PRECAUTIONS 1. PCB Design Precautions ◆Land pattern design Please do not arrange the surface and inside layer pattern near the antenna mounting area. ◆Land pattern design（Land pattern dimension examples and recommended antenna land pattern） AH168M AH316M AH083F 8 or more. 0.5 0.5 0.8 Feed Line 0.5 width 1.0 0.8 5 or more. 0.6 0.5 GND Unit : mm Land for Matching circuit (1005 chip) 50Ω Input Technical Considerations Land for Input terminal Land for NC terminal AH104F AH104N AH086M 2. Soldering ◆Conditions of Reflow soldering (for reference) ・ Pb Free Reflow Profile Technical Considerations Temperature（℃） 300 200 Peak 260℃ Max. Within 10sec. Slow cooling 100 0 Preheating150℃ Heating above 230℃ 60sec. Min. 40sec. Max. ※ Components should be preheated to within 100 to 130℃ from soldering temperature. ※ Assured to be reflow soldering for 2 times. Note : The above profiles are the maximum allowable soldering condition, therefore these profiles are not always recommended. 3. Storage Conditions Precautions ◆Storage conditions 1. The Products must not be used in the following environments : ・ exposure to special gases such as (C12, NH3, SOx, NOx) ・ exposure to volatile gas or inflammable gas ・ exposure to a lot of dust ・ exposure to water or condensation ・ exposure to direct sunlight or freezing 2. The Products should be kept in the following conditions : ・ Temperature : －10～＋40℃ ・ Humidity : 15～85％RH max. 3. The products should be used within 6 months after delivery. In case of storage over 6 months, solderability shall be checked before actual usage. ■ Please contact our offices for further details of specifications. All of the standard values listed here are subject to change without notice due to technical improvements. Therefore, please check the specifications carefully before use. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipantenna_prec_e-E09R01