0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
BK1608HS330-T

BK1608HS330-T

  • 厂商:

    TAIYO-YUDEN(太诱)

  • 封装:

    0603

  • 描述:

    FERRITE BEAD 33 OHM 0603 1LN

  • 数据手册
  • 价格&库存
BK1608HS330-T 数据手册
Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product Information in this Catalog Product information in this catalog is as of October 2019. All of the contents specified herein and production status of the products listed in this catalog are subject to change without notice due to technical improvement of our products, etc. Therefore, please check for the latest information carefully before practical application or use of our products. (4) Powe r g e n e r atio n c o ntro l e quip m e nt (nu c le a r p owe r, hydroelectric power, thermal power plant control system, etc.) (5) Undersea equipment (submarine repeating equipment, underwater work equipment, etc.) (6) Military equipment (7) Any other equipment requiring extremely high levels of safety and/or reliability equal to the equipment listed above Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. *Notes: 1. There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. 2. Implantable medical devices contain not only internal unit which is implanted in a body, but also external unit which is connected to the internal unit. ■ Approval of Product Specifications Ple a se c ont ac t TA IYO Y UD EN for fur the r det a ils of p ro duc t specifications as the individual product specification sheets are available. When using our products, please be sure to approve our product specifications or make a written agreement on the product specification with TAIYO YUDEN in advance. ■ Pre-Evaluation in the Actual Equipment and Conditions Please conduct validation and verification of our products in actual conditions of mounting and operating environment before using our products. ■ Limited Application 1. Equipment Intended for Use The products listed in this catalog are intended for generalpurpose and standard use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC) and other equipment specified in this catalog or the individual product specification sheets. TAIYO YUDEN has the line-up of the products intended for use in automotive electronic equipment, telecommunications infrastructure and industrial equipment, or medical devices classified as GHTF Classes A to C (Japan Classes I to III). Therefore, when using our products for these equipment, please check available applications specified in this catalog or the individual product specification sheets and use the corresponding products. 2. Equipment Requiring Inquiry Please be sure to contact TAIYO YUDEN for further information before using the products listed in this catalog for the following equipment (excluding intended equipment as specified in this catalog or the individual product specification sheets) which may cause loss of human life, bodily injury, serious property damage and/or serious public impact due to a failure or defect of the products and/or malfunction attributed thereto. (1) Transportation equipment (automotive powertrain control system, train control system, and ship control system, etc.) (2) Traffic signal equipment (3) Disaster prevention equipment, crime prevention equipment (4) Medical devices classified as GHTF Class C (Japan Class III) (5) H i g h l y p u b l i c i n f o r m a t i o n n e t wo r k e q u i p m e n t , d a t a processing equipment (telephone exchange, and base station, etc.) (6) Any other equipment requiring high levels of quality and/or reliability equal to the equipment listed above 3. Equipment Prohibited for Use Please do not incorporate our products into the following equipment requiring extremely high levels of safety and/or reliability. (1) Aerospace equipment (artificial satellite, rocket, etc.) (2) Aviation equipment *1 (3) Medical devices classified as GHTF Class D (Japan Class IV), implantable medical devices *2 4. Limitation of Liability Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment that is not intended for use by TAIYO YUDEN, or any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Safety Design When using our products for high safety and/or reliability-required equipment or circuits, please fully perform safety and/or reliability evaluation. In addition, please install (i) systems equipped with a protection circuit and a protection device and/or (ii) systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault for a failsafe design to ensure safety. ■ Intellectual Property Rights Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Limited Warranty Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a failure or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ TAIYO YUDEN’s Official Sales Channel The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter “TAIYO YUDEN’ s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’ s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export Administration Regulations”,“Foreign Exchange and Foreign Trade Control Law” of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 20 for General Electronic Equipment for General Electronic Equipment MULTILAYER CHIP BEAD INDUCTORS(BK SERIES) MULTILAYER CHIP BEAD INDUCTORS(BK SERIES) WAVE* WAVE* REFLOW REFLOW *Except for BK0603, BK1005 *Except for BK0603, BK1005 ■PARTS NUMBER B K △ ① 1 * Operating Temp.:-55~+125℃ 6 0 8 H ② ①Series name Code BK△ S 1 2 1 ④ ③ - T △ ⑤ ⑥ ⑦ ④Nominal impedance Code (example) 150 101 102 Series name Multilayer chip bead inductor ②Dimensions(L×W) Type(inch) 0603 1005 1608 2125 0603(0201) 1005(0402) 1608(0603) 2125(0805) ⑤Characteristics Code - Characteristics Standard ⑥Packaging Code T Material Packaging Taping ⑦Internal code Code △ Refer to impedance curves for material differences 15 100 1000 FERRITE BEAD INDUCTORS ③Material Code HW HS HR HM LM LL TS TM Dimensions (L×W)[mm] 0.6×0.3 1.0×0.5 1.6×0.8 2.0×1.25 Nominal impedance[Ω] NOISE SUPPRESSION COMPONENTS Code △=Blank space Internal code Standard ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY W L T e Type L W T e BK 0603 (0201) BK 1005 (0402) BK 1608 (0603) 0.60±0.03 (0.024±0.001) 1.00±0.05 (0.039±0.002) 1.6±0.15 (0.063±0.006) 2.0+0.3/-0.1 (0.079+0.012/-0.004) 2.0+0.3/-0.1 (0.079+0.012/-0.004) 0.30±0.03 (0.012±0.001) 0.50±0.05 (0.020±0.002) 0.8±0.15 (0.031±0.006) 1.25±0.2 (0.049±0.008) 1.25±0.2 (0.049±0.008) 0.30±0.03 (0.012±0.001) 0.50±0.05 (0.020±0.002) 0.8±0.15 (0.031±0.006) 0.85±0.2 (0.033±0.008) 1.25±0.2 (0.049±0.008) 0.15±0.05 (0.006±0.002) 0.25±0.10 (0.010±0.004) 0.3±0.2 (0.012±0.008) 0.5±0.3 (0.020±0.012) 0.5±0.3 (0.020±0.012) BK 2125 (0805) Standard quantity[pcs] Paper tape Embossed tape 15000 - 10000 - 4000 - 4000 - - 2000 Unit:mm(inch) i_mlci_BK_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 101 for General Electronic Equipment ■PARTS NUMBER ●BK 0603 Parts number NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS BK 0603HS220-T BK 0603HS330-T BK 0603HS800-T BK 0603HS121-T BK 0603HS241-T BK 0603HS601-T BK 0603HM600-T BK 0603HM121-T BK 0603HM241-T BK 0603HM471-T BK 0603HM601-T BK 0603HR121-T BK 0603HR241-T BK 0603HR601-T BK 0603HR102-T BK 0603HR122-T BK 0603LL100-T BK 0603LL220-T BK 0603LL330-T BK 0603LL470-T BK 0603LL560-T BK 0603LL800-T BK 0603LL121-T BK 0603TS800-T BK 0603TS121-T BK 0603TS241-T BK 0603TS601-T BK 0603TM800-T BK 0603TM121-T BK 0603TM241-T BK 0603TM601-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance [Ω] 22 33 80 120 240 600 60 120 240 470 600 120 240 600 1000 1200 10 22 33 47 56 80 120 80 120 240 600 80 120 240 600 Impedance tolerance ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Measuring frequency [MHz] 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance [Ω](max.) 0.065 0.070 0.40 0.45 0.65 1.20 0.25 0.40 0.80 1.05 1.20 0.23 0.38 0.80 1.15 1.30 0.25 0.45 0.55 0.70 1.00 1.30 1.50 0.18 0.23 0.32 0.75 0.18 0.23 0.38 0.85 Rated current [mA](max.) 500 500 200 200 200 150 200 200 200 100 100 450 350 250 220 200 200 200 150 150 100 100 100 500 450 400 270 450 400 300 250 Thickness [mm] 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 Measuring frequency [MHz] 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance [Ω](max.) 0.17 0.24 0.31 0.50 0.60 0.03 0.06 0.10 0.10 0.20 0.30 0.45 0.55 0.58 0.60 0.18 0.18 0.30 0.45 0.50 0.70 0.11 0.18 0.25 0.33 0.31 0.45 0.50 0.70 0.90 Rated current [mA](max.) 500 450 400 350 300 1,000 700 700 700 500 400 350 300 300 300 350 300 300 250 250 150 500 400 400 350 400 350 300 250 120 Thickness [mm] 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 ●BK 1005 Parts number BK 1005HW680-T BK 1005HW121-T BK 1005HW241-T BK 1005HW431-T BK 1005HW601-T BK 1005HS100-T BK 1005HS330-T BK 1005HS680-T BK 1005HS800-T BK 1005HS121-T BK 1005HS241-T BK 1005HS431-T BK 1005HS601-T BK 1005HS102-T BK 1005HR601-T BK 1005HM750-T BK 1005HM121-T BK 1005HM241-T BK 1005HM471-T BK 1005HM601-T BK 1005HM102-T BK 1005LL100-T BK 1005LL220-T BK 1005LL330-T BK 1005LL470-T BK 1005LL680-T BK 1005LL121-T BK 1005LL181-T BK 1005LL241-T BK 1005LM182-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance [Ω] 68 120 240 430 600 10 33 68 80 120 240 430 600 1000 600 75 120 240 470 600 1000 10 22 33 47 68 120 180 240 1800 Impedance tolerance ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% i_mlci_BK_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 102 20 for General Electronic Equipment ■PARTS NUMBER ●BK 1608 Parts number Impedance tolerance ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Measuring frequency [MHz] 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance [Ω](max.) 0.15 0.25 0.30 0.40 0.05 0.08 0.10 0.10 0.10 0.18 0.25 0.45 0.60 0.20 0.35 0.45 0.60 0.70 0.20 0.30 0.30 0.35 0.50 0.65 0.80 0.85 0.85 0.90 1.00 0.60 0.75 0.85 1.10 0.21±30% 0.27±30% 0.30±30% Rated current [mA](max.) 600 450 400 300 1,500 1,200 900 800 600 500 400 350 300 350 300 250 250 200 500 400 400 300 300 250 250 200 200 200 150 300 250 200 200 400 350 300 Thickness [mm] 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 Measuring frequency [MHz] 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance [Ω](max.) 0.05 0.05 0.05 0.05 0.10 0.10 0.15 0.20 0.25 0.30 0.40 0.15 0.20 0.25 0.25 0.35 0.20 0.30 0.35 0.30 0.35 0.45 0.75 Rated current [mA](max.) 1,200 1,200 1,200 1,000 1,000 900 800 600 500 500 300 800 600 500 500 400 600 400 300 400 400 300 200 Thickness [mm] 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 1.25 ±0.2 1.25 ±0.2 ●BK 2125 Parts number BK 2125HS150-T BK 2125HS220-T BK 2125HS330-T BK 2125HS470-T BK 2125HS750-T BK 2125HS101-T BK 2125HS121-T BK 2125HS241-T BK 2125HS431-T BK 2125HS601-T BK 2125HS102-T BK 2125HM121-T BK 2125HM241-T BK 2125HM471-T BK 2125HM601-T BK 2125HM102-T BK 2125LL560-T BK 2125LL121-T BK 2125LL241-T BK 2125LM751-T BK 2125LM152-T BK 2125LM182-T BK 2125LM252-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance [Ω] 15 22 33 47 75 100 120 240 430 600 1000 120 240 470 600 1000 56 120 240 750 1500 1800 2500 Impedance tolerance ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% FERRITE BEAD INDUCTORS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance [Ω] 120 240 430 600 22 33 47 60 80 120 240 600 1000 120 240 470 600 1000 30 47 56 68 120 180 240 330 430 510 680 750 1500 1800 2500 430 600 1000 NOISE SUPPRESSION COMPONENTS BK 1608HW121-T BK 1608HW241-T BK 1608HW431-T BK 1608HW601-T BK 1608HS220-T BK 1608HS330-T BK 1608HS470-T BK 1608HS600-T BK 1608HS800-T BK 1608HS121-T BK 1608HS241-T BK 1608HS601-T BK 1608HS102-T BK 1608HM121-T BK 1608HM241-T BK 1608HM471-T BK 1608HM601-T BK 1608HM102-T BK 1608LL300-T BK 1608LL470-T BK 1608LL560-T BK 1608LL680-T BK 1608LL121-T BK 1608LL181-T BK 1608LL241-T BK 1608LL331-T BK 1608LL431-T BK 1608LL511-T BK 1608LL681-T BK 1608LM751-T BK 1608LM152-T BK 1608LM182-T BK 1608LM252-T BK 1608TS431-T BK 1608TS601-T BK 1608TS102-T EHS i_mlci_BK_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 103 for General Electronic Equipment ■ ELECTRICAL CHARACTERISTICS ■ BK0603 100 80 Impedance [Ω] 60 40 Z 80 200 200 60 150 150 40 0 1 1000 BK0603 HS601 R 200 X 100 0 1 600 150 150 100 100 50 50 400 Z 200 BK0603 HR241 400 10 100 1000 Frequency[MHz] Z 1 Impedance [Ω] 200 150 R 100 0 10 100 1 R 400 1 10 100 1000 Frequency[MHz] BK0603 LL100 250 Impedance [Ω] 100 Z 50 600 Z 400 R R 500 400 300 10 100 1000 Frequency[MHz] 10000 BK0603 LL560 500 100 1000 10000 BK0603 HR121 Z 140 R 120 100 80 X 20 0 BK0603 HR102 1 10 100 1000 Frequency [MHz] 10000 BK0603 HR122 2000 1000 500 Z 1000 500 X X X R 0 10 100 1000 Frequency [MHz] BK0603 LL330 500 100 Z R 400 300 200 Z R 100 10 100 1000 Frequency[MHz] Z 200 0 10000 R X X BK0603 LL800 1000 300 100 X 1 BK0603 LL470 500 400 150 R 0 10000 BK0603 LL220 R 1 10 1500 600 0 1 40 Z 50 X 10000 Z 200 150 1000 160 1500 700 250 200 100 180 0 10000 10 200 X BK0603 HR601 01 10000 10000 200 X 100 10 100 1000 Frequency [MHz] 1000 800 200 X 50 X 1 BK0603 HM601 1000 Z 800 250 0 10000 900 300 Impedance [Ω] X BK0603 HM471 1000 350 Impedance [Ω] 1 600 0 10000 10000 200 200 10 100 1000 Frequency[MHz] 1000 250 Impedance[ ] Impedance [Ω] 300 100 200 800 Z 10 250 1000 400 Impedance [Ω] FERRITE BEAD INDUCTORS BK0603 HM241 500 1 800 0 10000 10000 Impedance[ ] NOISE SUPPRESSION COMPONENTS Impedance [Ω] 10 100 1000 Frequency[MHz] Impedance [Ω] 10000 X R 100 50 X 10 100 1000 Frequency [MHz] 10 Z R Z 50 1000 1 R 100 100 Z R 20 X 1 250 Impedance[ ] 0 R 250 Impedance [Ω] 20 BK0603 HS330 Impedance [Ω] Impedance [Ω] BK0603 HS220 100 1 10 100 1000 Frequency[MHz] 0 10000 BK0603 LL121 1000 1 10 100 1000 Frequency[MHz] 10000 BK0603 TS800 200 Z 200 100 0 600 Z R 400 200 1 X 10 100 1000 Frequency[MHz] 10000 0 150 600 Z Impedance [Ω] R 300 800 Impedance [Ω] 800 Impedance [Ω] Impedance [Ω] 400 R 400 200 1 X 10 100 1000 Frequency[MHz] 10000 0 100 Z 50 X 1 10 100 1000 Frequency[MHz] 10000 R 0 X 1 10 100 1000 Frequency[MHz] 10000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 104 20 for General Electronic Equipment ■ ELECTRICAL CHARACTERISTICS Z 100 R 50 Z 200 100 X 1 300 10 100 1000 Frequency[MHz] 0 10000 10 100 1000 Frequency[MHz] Z 400 200 X 1 150 600 R 0 10000 BK0603 TM800 200 800 Impedance [Ω] 150 BK0603 TS601 1000 400 Impedance [Ω] Impedance [Ω] 200 0 BK0603 TS241 500 Impedance [Ω] BK0603 TS121 250 100 R Z 50 R X 1 10 100 1000 Frequency[MHz] 0 10000 X 1 10 100 1000 Frequency[MHz] 10000 ■ BK1005 500 100 R 50 X 200 1 10 100 1000 Frequency[MHz] 0 10000 R 50 1 10 100 1000 Frequency[MHz] 0 10000 R 1 20 Z R 1 10 100 1000 Frequency[MHz] R Z Z R 10 100 1 600 Z 400 R X 10 100 1000 Frequency[MHz] 0 10000 BK1005 HS680 10000 Z R 1 Frequency[MHz] 1000 200 800 Impedance [Ω] 100 50 10000 150 100 Z 50 R X X 1000 10 100 1000 Frequency[MHz] 200 100 0 1 BK1005 HS800 250 150 250 10 100 1000 Frequency[MHz] 0 10000 1 10 100 1000 Frequency[MHz] 10000 BK1005 HS431 600 400 Z 200 0 BK1005 HR601 BK1005 HS102 2000 1000 800 1 R X 10 100 1000 Frequency[MHz] BK1005 HM750 200 200 150 100 400 Z 200 R 1 X 10 100 1000 Frequency[MHz] 0 BK1005 HM121 250 600 1000 10000 Impedance [Ω] 0 0 BK1005 HW601 200 X 150 Impedance [Ω] 400 50 1 10000 800 200 40 10000 X 10 100 1000 Frequency[MHz] 1000 250 60 0 1 BK1005 HW431 BK1005 HS330 20 X 0 600 0 10000 Impedance [Ω] Impedance [Ω] 40 R X 80 60 Z 10000 200 10 100 1000 Frequency[MHz] 100 80 0 Z 100 R 10 100 1000 Frequency[MHz] X BK1005 HS100 100 200 100 X Impedance [Ω] Impedance [Ω] 100 X 1 800 300 150 50 1000 400 Z 400 0 10000 BK1005 HW241 500 150 0 R 10 100 1000 Frequency[MHz] Z 200 X 1 600 FERRITE BEAD INDUCTORS BK1005 HW121 200 Impedance [Ω] Z 100 250 Impedance [Ω] 300 200 Impedance [Ω] Z BK1005 HW680 250 800 Impedance [Ω] Impedance [Ω] 400 150 0 1000 NOISE SUPPRESSION COMPONENTS Impedance [Ω] 200 BK0603 TM601 Impedance [Ω] 250 BK0603 TM241 Impedance [Ω] BK0603 TM121 50 Z 150 R 100 50 0 0 10000 1 X 10 100 1000 Frequency[MHz] 10000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 105 for General Electronic Equipment ■ ELECTRICAL CHARACTERISTICS BK1005 HM102 500 2000 400 300 1000 200 100 0 0 1 10 100 1000 1 10000 BK1005 LL220 BK1005 LL100 250 200 NOISE SUPPRESSION COMPONENTS 150 100 50 1 10 100 1000 10000 500 500 200 400 400 150 300 300 100 200 200 50 100 100 1 10 100 1000 10000 100 1000 10000 BK1005 LL470 BK1005 LL330 250 0 0 10 0 0 1 10 100 1000 10000 1 10 100 1000 10000 FERRITE BEAD INDUCTORS BK1005 LL680 500 400 300 200 100 0 1 10 100 1000 10000 ■ BK1608 BK1005 LM182 2500 2000 1500 Z 1000 R 500 X 0 1 10 100 1000 10000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 106 20 for General Electronic Equipment ■ ELECTRICAL CHARACTERISTICS BK1608 LL300 500 0 1 BK1608 LL560 500 500 1500 250 250 250 750 10 100 1000 10000 1 10 100 1000 1 10000 10000 0 0 0 1 1000 BK1608 LL121 BK1608 LL680 500 0 100 10 100 1000 10000 1 10 100 1000 4000 FERRITE BEAD INDUCTORS BK1608 LL470 10 NOISE SUPPRESSION COMPONENTS 250 2000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 107 for General Electronic Equipment ■ ELECTRICAL CHARACTERISTICS ■ BK2125 NOISE SUPPRESSION COMPONENTS FERRITE BEAD INDUCTORS 1000 Z 500 R X 0 1 10 100 1000 1000 Z R 500 0 X 1 10 100 1000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 108 20 Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils(MC series F type) Metal Multilayer Chip Power Inductors (MCOILTM MC series) ■PACKAGING ①Minimum Quantity ●Tape & Reel Packaging Type CK1608(0603) CK2125(0805) CKS2125(0805) CKP1608(0603) CKP2012(0805) CKP2016(0806) CKP2520(1008) LK1005(0402) LK1608(0603) LK2125(0805) HK0603(0201) HK1005(0402) HK1608(0603) HK2125(0805) HKQ0603S(0201) HKQ0603U(0201) AQ105(0402) BK0603(0201) BK1005(0402) BKH0603(0201) BKH1005(0402) BK1608(0603) BK2125(0805) BK2010(0804) BK3216(1206) BKP0603(0201) BKP1005(0402) BKP1608(0603) BKP2125(0805) MCF0605(0202) MCF0806(0302) MCF1210(0504) MCF2010(0804) MCEE1005(0402) MCEK1210(0504) MCFK1608(0603) MCFE1608(0603) MCHK1608(0603) MCKK1608(0603) MCHK2012(0806) MCKK2012(0805) Thickness mm(inch) 0.8 (0.031) 0.85(0.033) 1.25(0.049) 0.85(0.033) 1.25(0.049) 0.8 (0.031) 0.9 (0.035) 0.9 (0.035) 0.7 (0.028) 0.9 (0.035) 1.1 (0.043) 0.5 (0.020) 0.8 (0.031) 0.85(0.033) 1.25(0.049) 0.3 (0.012) 0.5 (0.020) 0.8 (0.031) 0.85(0.033) 1.0 (0.039) 0.3 (0.012) 0.3 (0.012) 0.5 (0.020) 0.3 (0.012) 0.5 (0.020) 0.3 (0.012) 0.5 (0.020) 0.8 (0.031) 0.85(0.033) 1.25(0.049) 0.45(0.018) 0.8 (0.031) 0.3 (0.012) 0.5 (0.020) 0.8 (0.031) 0.85(0.033) 0.3 (0.012) 0.4 (0.016) 0.55(0.022) 0.45(0.018) 0.55(0.022) 0.5 (0.020) 0.6 (0.024) 0.65(0.026) 0.8 (0.031) 1.0 (0.039) 0.8 (0.031) 1.0 (0.039) Standard Quantity [pcs] Paper Tape Embossed Tape 4000 - 4000 - - 2000 4000 - - 2000 4000 - - 3000 - 3000 - 3000 - 3000 - 2000 10000 - 4000 - 4000 - - 2000 15000 - 10000 - 4000 - - 4000 - 3000 15000 - 15000 - 10000 - 15000 - 10000 - 15000 - 10000 - 4000 - 4000 - - 2000 4000 - - 4000 15000 - 10000 - 4000 - 4000 - 15000 - - 10000 - 5000 - 4000 10000 - 5000 - 4000 - 4000 - 4000 - 3000 4000 - 3000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01 ②Taping material ●Card board carrier tape Top tape Base tape Sprocket hole Bottom tape CK CKP CK CKS LK LK LK HK HK HK HKQ AQ 1608 1608 2125 2125 1005 1608 2125 0603 1005 1608 0603 105 BK BK BK BK BK BKP BKP BKP BKP BKH BKH MCF MC MC MC MC 0603 1005 1608 2125 2010 0603 1005 1608 2125 0603 1005 0605 1005 1210 1608 2012 CK CKS CKP CKP CKP LK HK 2125 2125 2012 2016 2520 2125 2125 BK BK MCF MCF MCF MC MC 2125 3216 0806 1210 2010 1608 2012 Chip cavity Chip Filled Chip ●Embossed Tape Top tape Sprocket hole Base tape Chip cavity Chip Filled Chip ③Taping Dimensions ●Paper tape (8mm wide) B T 8.0±0.3 (0.315±0.012) A F Unit:mm(inch) 1.75±0.1 (0.069±0.004) 3.5±0.05 (0.138±0.002) Sprocket hole φ1.5+0.1/-0 (φ0.059+0.004/-0) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01 Type Thickness mm(inch) CK1608(0603) 0.8 (0.031) CK2125(0805) 0.85(0.033) CKS2125(0805) 0.85(0.033) CKP1608(0603) 0.8 (0.031) LK1005(0402) 0.5 (0.020) LK1608(0603) 0.8 (0.031) LK2125(0805) 0.85(0.033) HK0603(0201) 0.3 (0.012) HK1005(0402) 0.5 (0.020) HK1608(0603) 0.8 (0.031) HKQ0603S(0201) 0.3 (0.012) HKQ0603U(0201) 0.3 (0.012) AQ105(0402) 0.5 (0.020) BK0603(0201) 0.3 (0.012) BK1005(0402) 0.5 (0.020) BK1608(0603) 0.8 (0.031) BK2125(0805) 0.85(0.033) BK2010(0804) 0.45(0.018) BKP0603(0201) 0.3 (0.012) BKP1005(0402) 0.5 (0.020) BKP1608(0603) 0.8 (0.031) BKP2125(0805) 0.85(0.033) BKH0603(0201) 0.3 (0.012) BKH1005(0402) 0.5 (0.020) MCF0605(0202) 0.3 (0.012) MCFK1608(0603) 0.6 (0.024) MCEE1005(0402) 0.55(0.021) MCEK1210(0504) 0.5 (0.020) MCFK1608(0603) 0.6 (0.024) MCFE1608(0603) 0.65(0.026) MCHK1608(0603) 0.8 (0.031) MCHK2012(0805) 0.8 (0.031) Chip cavity A B 1.0±0.2 1.8±0.2 (0.039±0.008) (0.071±0.008) 1.5±0.2 2.3±0.2 (0.059±0.008) (0.091±0.008) 1.5±0.2 2.3±0.2 (0.059±0.008) (0.091±0.008) 1.0±0.2 1.8±0.2 (0.039±0.008) (0.071±0.008) 0.65±0.1 1.15±0.1 (0.026±0.004) (0.045±0.004) 1.0±0.2 1.8±0.2 (0.039±0.008) (0.071±0.008) 1.5±0.2 2.3±0.2 (0.059±0.008) (0.091±0.008) 0.40±0.06 0.70±0.06 (0.016±0.002) (0.028±0.002) 0.65±0.1 1.15±0.1 (0.026±0.004) (0.045±0.004) 1.0±0.2 1.8±0.2 (0.039±0.008) (0.071±0.008) 0.40±0.06 0.70±0.06 (0.016±0.002) (0.028±0.002) 0.40±0.06 0.70±0.06 (0.016±0.002) (0.028±0.002) 0.75±0.1 1.15±0.1 (0.030±0.004) (0.045±0.004) 0.40±0.06 0.70±0.06 (0.016±0.002) (0.028±0.002) 0.65±0.1 1.15±0.1 (0.026±0.004) (0.045±0.004) 1.0±0.2 1.8±0.2 (0.039±0.008) (0.071±0.008) 1.5±0.2 2.3±0.2 (0.059±0.008) (0.091±0.008) 1.2±0.1 2.17±0.1 (0.047±0.004) (0.085±0.004) 0.40±0.06 0.70±0.06 (0.016±0.002) (0.028±0.002) 0.65±0.1 1.15±0.1 (0.026±0.004) (0.045±0.004) 1.0±0.2 1.8±0.2 (0.039±0.008) (0.071±0.008) 1.5±0.2 2.3±0.2 (0.059±0.008) (0.091±0.008) 0.40±0.06 0.70±0.06 (0.016±0.002) (0.028±0.002) 0.65±0.1 1.15±0.1 (0.026±0.004) (0.045±0.004) 0.62±0.03 0.77±0.03 (0.024±0.001) (0.030±0.001) 1.1±0.05 1.9±0.05 (0.043±0.002) (0.075±0.002) 0.8±0.05 1.3±0.05 (0.031±0.002) (0.051±0.002) 1.3±0.1 1.55±0.1 (0.051±0.004) (0.061±0.004) 1.1±0.05 1.9±0.05 (0.043±0.002) (0.075±0.002) 1.1±0.05 1.9±0.05 (0.043±0.002) (0.075±0.002) 1.2±0.05 2.0±0.05 (0.047±0.002) (0.079±0.002) 1.65±0.1 2.4±0.1 (0.065±0.004) (0.094±0.004) Insertion Pitch F 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) 2.0±0.05 (0.079±0.002) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) 2.0±0.05 (0.079±0.002) 2.0±0.05 (0.079±0.002) 2.0±0.05 (0.079±0.002) 2.0±0.05 (0.079±0.002) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) 2.0±0.05 (0.079±0.002) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) 2.0±0.05 (0.079±0.002) 2.0±0.05 (0.079±0.002) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) Tape Thickness T 1.1max (0.043max) 1.1max (0.043max) 1.1max (0.043max) 1.1max (0.043max) 0.8max (0.031max) 1.1max (0.043max) 1.1max (0.043max) 0.45max (0.018max) 0.8max (0.031max) 1.1max (0.043max) 0.45max (0.018max) 0.45max (0.018max) 0.8max (0.031max) 0.45max (0.018max) 0.8max (0.031max) 1.1max (0.043max) 1.1max (0.043max) 0.8max (0.031max) 0.45max (0.018max) 0.8max (0.031max) 1.1max (0.043max) 1.1max (0.043max) 0.45max (0.018max) 0.8max (0.031max) 0.45max (0.018max) 0.72max (0.028max) 0.64max (0.025max) 0.64max (0.025max) 0.72max (0.028max) 0.72max (0.028max) 0.9max (0.035max) 0.9max (0.035max) Unit : mm(inch) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01 ●Embossed Tape (8mm wide) Unit:mm(inch) 3.5±0.05 (0.138±0.002) Sprocket hole A B F 8.0±0.3 (0.315±0.012) 1.75±0.1 (0.069±0.004) φ1.5+0.1/-0 (φ0.059+0.004/-0) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) Thickness mm(inch) Type CK2125(0805) 1.25(0.049) CKS2125(0805) 1.25(0.049) CKP2012(0805) 0.9 (0.035) CKP2016(0806) 0.9 (0.035) Chip cavity A B 1.5±0.2 2.3±0.2 (0.059±0.008) (0.091±0.008) 1.5±0.2 2.3±0.2 (0.059±0.008) (0.091±0.008) 1.55±0.2 2.3±0.2 (0.061±0.008) (0.091±0.008) 1.8±0.1 2.2±0.1 (0.071±0.004) (0.087±0.004) Insertion Pitch F 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 2.3±0.1 (0.091±0.004) 2.8±0.1 (0.110±0.004) 4.0±0.1 (0.157±0.004) 1.5±0.2 (0.059±0.008) 2.3±0.2 (0.091±0.008) 4.0±0.1 (0.157±0.004) 1.5±0.2 (0.059±0.008) 2.3±0.2 (0.091±0.008) 4.0±0.1 (0.157±0.004) 1.5±0.2 (0.059±0.008) 1.9±0.1 (0.075±0.004) 0.75±0.05 (0.030±0.002) 1.15±0.05 (0.045±0.002) 1.1±0.1 (0.043±0.004) 1.1±0.1 (0.043±0.004) 1.55±0.1 (0.061±0.004) 2.3±0.2 (0.091±0.008) 3.5±0.1 (0.138±0.004) 0.95±0.05 (0.037±0.002) 1.40±0.05 (0.055±0.002) 2.3±0.1 (0.091±0.004) 1.95±0.1 (±0.004) 2.35±0.1 (0.093±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 0.7 (0.028) 0.9 (0.035) CKP2520(1008) 1.1 (0.043) 1.1 (0.043) LK2125(0805) 1.25(0.049) 0.85(0.033) HK2125(0805) 1.0 (0.039) BK2125(0805) 1.25(0.049) BK3216(1206) 0.8 (0.031) MCF0806(0302) 0.4 (0.016) MCF1210(0504) 0.55(0.022) MCF2010(0804) 0.45(0.018) MCKK1608(0603) 1.0 (0.039) MCKK2012(0805) 1.0 (0.039) Tape Thickness K T 2.0 0.3 (0.079) (0.012) 2.0 0.3 (0.079) (0.012) 1.3 0.3 (0.051) (0.012) 1.3 0.25 (0.051) (0.01) 1.4 (0.055) 1.4 (0.055) 0.3 (0.012) 1.7 (0.067) 1.7 (0.067) 2.0 0.3 (0.079) (0.012) 1.5 (0.059) 0.3 (0.012) 2.0 (0.079) 2.0 0.3 (0.079) (0.012) 1.4 0.3 (0.055) (0.012) 0.55 0.3 (0.022) (0.012) 0.65 0.3 (0.026) (0.012) 0.85 0.3 (0.033) (0.012) 1.4 0.25 (0.055) (0.01) 1.35 0.25 (0.053) (0.010) Unit : mm(inch) ④LEADER AND BLANK PORTION Blank portion 160mm or more (6.3inches or more) Chip cavity Blank portion Leader 100mm or more (3.94inches or more) Direction of tape feed 400mm or more (15.7inches or more) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01 ⑤Reel Size t E C R B D A W A φ178±2.0 B φ50 or more C φ13.0±0.2 4mm width tape 8mm width tape t 1.5max. 2.5max. W 5±1.0 10±1.5 D φ21.0±0.8 E 2.0±0.5 R 1.0 (Unit : mm) ⑥Top tape strength The top tape requires a peel-off force of 0.1~0.7N in the direction of the arrow as illustrated below. Pull direction 0~15° Top tape Base tape ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E08R01 Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils(MC series F type) Metal Multilayer Chip Power Inductors (MCOILTM MC series) ■RELIABILITY DATA 1. Operating Temperature Range BK series BKH series BKP series MCF series CK series CKS series Specified Value CKP series LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series 2. Storage Temperature Range BK series BKH series BKP series MCF series CK series CKS series Specified Value CKP series LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series -55~+125℃ -55~+85℃ -40~+85℃ -40~+85℃ -55~+125℃ -40~+85℃ -55~+125℃ -40~+125℃(Including self-generated heat) -55~+125℃ -55~+85℃ -40~+85℃ -40~+85℃ -55~+125℃ -40~+85℃ -55~+125℃ -40~+85℃ 3. Rated Current Specified Value BK series BKH series BKP series MCF series CK series CKS series CKP series LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series The temperature of the element is increased within 20℃. The temperature of the element is increased within 40℃ Refer to each specification. The temperature of the element is increased within 20℃. The temperature of the element is increased within 40℃ The decreasing-rate of inductance value is within 5 % The decreasing-rate of inductance value is within 5 %, or the temperature of the element is increased within 20℃ Idc1: The decreasing-rate of inductance value is within 30 % Idc2: The temperature of the element is increased within 40℃ ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01 4. Impedance Specified Value Test Methods and Remarks BK series BKH series Refer to each specification. BKP series MCF series BK0603Series, BKP0603Series, BKH Series Measuring frequency : 100±1MHz Measuring equipment : 4991A(or its equivalent) Measuring jig : 16193A(or its equivalent) BK1005Series, BKP1005Series ,BKH1005Series Measuring frequency : 100±1MHz Measuring equipment : 4291A(or its equivalent) Measuring jig : 16192A ( or its equivalent ) , HW:16193A ( or its equivalent) BK1608・2125Series, BKP1608・2125Series Measuring frequency : 100±1MHz Measuring equipment : 4291A(or its equivalent), 4195A(or its equivalent) Measuring jig : 16192A(or its equivalent), HW:16193A(or its equivalent) BK2010・3216Series Measuring frequency : 100±1MHz Measuring equipment : 4291A(or its equivalent), 4195A(or its equivalent) Measuring jig : 16192A(or its equivalent) MCF Series Measuring frequency : 100±1MHz Measuring equipment : 4291A(or its equivalent) 5. Inductance Specified Value CK series CKS series CKP series LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series CK、CKS、LK Series Measuring frequency Measuring equipment /jig Measuring current CKP、MCOILTM MC Series Measuring frequency Measuring equipment Test Methods and Remarks Refer to each specification. : Refer to each specification. : 1608,2125⇒4294A+16092A(or its equivalent) 1005⇒4291A+16193A(or its equivalent) : 047~4.7μH ⇒1mArms 、 5.6~33μH ⇒0.1mArms : 1MHz : 4285A(or its equivalent) HK0603、HK1005、AQ Series Measuring frequency : 100MHz Measuring equipment /jig : HK0603⇒ E4991A+16197A(or its equivalent) , AQ105⇒4291A+16197A(or its equivalent) HK1005⇒ 4291A+16193A(or its equivalent) HK1608、HK2125 Series Measuring frequency : ~100nH⇒100MHz 、120nH~⇒50MHz Measuring equipment /jig : 4291A+16092A(or its equivalent) HKQ Series Measuring frequency : 500MHz Measuring equipment /jig : E4991A+16197A(or its equivalent) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01 6. Q Specified Value Test Methods and Remarks CK series CKS series - CKP series LK series HK0603, HK1005 Refer to each specification. HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series - LK Series Measuring frequency : Refer to each specification. Measuring equipment /jig : 1608,2125⇒4294A+16092A(or its equivalent) 1005⇒4291A+16193A(or its equivalent) Measuring current : 047~4.7μH ⇒1mArms 、 5.6~33μH ⇒0.1mArms HK0603、HK1005、AQ Series Measuring frequency : 100MHz Measuring equipment /jig : HK0603⇒E4991A+16197A(or its equivalent) , AQ105⇒4291A+16197A(or its equivalent) HK1005⇒4291A+16193A(or its equivalent) HK1608、HK2125 Series Measuring frequency : ~100nH⇒100MHz 、120nH~⇒50MHz Measuring equipment /jig : 4291A+16092A(or its equivalent) HKQ Series Measuring frequency : 500MHz Measuring equipment /jig : E4991A+16197A(or its equivalent) 7. DC Resistance Specified Value BK series BKH series BKP series MCF series CK series CKS series CKP series LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series Test Methods and Remarks Measuring equipment:IWATSU VOAC7512, HIOKI RM3545 (or its equivalent) 8. Self Resonance Frequency(SRF) BK series BKH series BKP series MCF series CK series CKS series Specified Value CKP series LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series LK、CK Series : Measuring equipment Test Methods and Measuring jig Remarks HK、HKQ、AQ Series : Measuring equipment Refer to each specification. - Refer to each specification. - Refer to each specification. - : 4195A(or its equivalent) : 16092A(or its equivalent) : 8719C(or its equivalent) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01 9. Resistance to Flexure of Substrate BK series BKH series BKP series MCF series CK series CKS series Specified Value CKP series No mechanical damage. LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series Warp : 2mm(BK Series、BKP、BKH1005、CK、CKS、CKP、LK、HK、HKQ0603S、HKQ0603U、AQ Series、MCF1210、MC Series) : 1mm(BKH0603、MCF Series without 1210 size,) Testing board : glass epoxy-resin substrate Thickness : 0.8mm 20 Test Methods and Remarks R-230 Board Warp Deviation±1 45 45 (Unit:mm) 10. Solderability Specified Value Test Methods and Remarks BK series BKH series BKP series MCF series CK series CKS series CKP series LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 MCOILTM MC series Solder temperature Solder temperature Duration At least 90% of terminal electrode is covered by new solder. :230±5℃ (JIS Z 3282 H60A or H63A) :245±3℃ (Sn/3.0Ag/0.5Cu) :4±1 sec. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01 11. Resistance to Soldering BK series BKH series BKP series MCF series CK series CKS series Specified Value CKP series LK series Appearance:No significant abnormality Impedance change:Within ±30% Appearance:No significant abnormality Impedance change:Within ±20% Appearance:No significant abnormality Inductance change: R10~4R7⇒Within ±10%、 6R8~100⇒Within ±15% Appearance:No significant abnormality Inductance change:Within ±20% Appearance:No significant abnormality Inductance change:Within ±30% Appearance:No significant abnormality Inductance change:1005⇒Within ±15% 1608,2125⇒ 47N~4R7: Within ±10% 5R6~330: Within ±15% HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 Appearance:No significant abnormality Inductance change: Within ±5% MCOILTM MC series Appearance:No significant abnormality Inductance change: Within ±10% Solder temperature :260±5℃ Duration :10±0.5 sec. Test Methods and Preheating temperature :150 to 180℃ Remarks Preheating time :3 min. Flux :Immersion into methanol solution with colophony for 3 to 5 sec. Recovery :2 to 3 hrs of recovery under the standard condition after the test.(See Note 1) (Note 1) When there are questions concerning measurement result;measurement shall be made after 48±2 hrs of recovery under the standard condition. 12. Thermal Shock BK series BKH series BKP series MCF series CK series CKS series Specified Value CKP series LK series Appearance:No significant abnormality Impedance change: Within ±30% Appearance:No significant abnormality Impedance change: Within ±20% Appearance:No significant abnormality Inductance change:Within ±20% Appearance:No significant abnormality Inductance change: Within ±30% Appearance:No significant abnormality Inductance change: Within ±10% Q change: Within ±30% HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 Appearance:No significant abnormality Inductance change: Within ±10% Q change: Within ±20% MCOILTM MC series Appearance:No significant abnormality Inductance change: Within ±10% Conditions for 1 cycle Step temperature(℃) time(min.) 1 Minimum operating temperature +0/-3 30±3 Test Methods and 2 Room temperature 2~3 Remarks 3 Maximum operating temperature +3/-0 30±3 4 Room temperature 2~3 Number of cycles:5 Recovery:2 to 3 hrs of recovery under the standard condition after the test.(See Note 1) (Note 1) When there are questions concerning measurement result;measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01 13. Damp Heat( Steady state) BK series BKH series BKP series MCF series CK series CKS series CKP series Specified Value LK series HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 Appearance:No significant abnormality Impedance change: Within ±30% Appearance:No significant abnormality Impedance change: Within ±20% Appearance:No significant abnormality Inductance change: Within ±20% Appearance:No significant abnormality Inductance change: Within ±30% Appearance:No significant abnormality Inductance change: 1005,1608⇒Within ±10% Q change: Within ±30% 2125⇒Within ±20% Appearance:No significant abnormality Inductance change: Within ±10% Q change: Within ±20% Appearance:No significant abnormality Inductance change: Within ±10% BK、BKP、BKH、LK、CK、CKS、CKP、MCF Series: Temperature :40±2℃ Humidity :90 to 95%RH Duration :500 +24/-0 hrs Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber.(See Note 1) MCOILTM MC series Test Methods and Remarks HK、HKQ、AQ、MCOILTM MC series: Temperature :60±2℃ Humidity :90 to 95%RH Duration :500 +24/-0 hrs Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber.(See Note 1) (Note 1) When there are questions concerning measurement result;measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01 14. Loading under Damp Heat BK series BKH series BKP series MCF series CK series CKS series CKP series Specified Value LK series Test Methods and Remarks Appearance:No significant abnormality Impedance change: Within ±30% - Appearance:No significant abnormality Inductance change: Within ±20% Appearance:No significant abnormality Inductance change: Within ±30% Appearance:No significant abnormality Inductance change: 1005⇒Within ±10% 1608⇒0.047~12.0μH: Within ±10% 15% 2125⇒Within ±20% Q change: Within ±30% 15.0~33.0μH: Within ± HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 Appearance:No significant abnormality Inductance change: Within ±10% Q change: Within ±20% MCOILTM MC series※ Appearance:No significant abnormality Inductance change: Within ±10% BK、BKP、BKH、LK、CK、CKS、CKP Series: Temperature :40±2℃ Humidity :90 to 95%RH Applied current :Rated current Duration :500 +24/-0 hrs Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber.(See Note 1) HK、HKQ、AQ、MCOILTM MC Series: Temperature :60±2℃ Humidity :90 to 95%RH Applied current :Rated current ※MC series ; Idc2max Duration :500 +24/-0 hrs Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber.(See Note 1) Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01 15. Loading at High Temperature BK series BKH series BKP series MCF series CK series CKS series CKP series Specified Value LK series Test Methods and Remarks Appearance:No significant abnormality Impedance change: Within ±30% Appearance:No significant abnormality Impedance change: Within ±20% Appearance:No significant abnormality Inductance change: Within ±20% Appearance:No significant abnormality Inductance change: Within ±30% Appearance:No significant abnormality Inductance change: 1005⇒Within ±10% 1608⇒0.047~12.0μH: Within ±10% 15% 2125⇒Within ±20% Q change: Within ±30% 15.0~33.0μH: Within ± HK0603, HK1005 HK1608, HK2125 HKQ0603 AQ105 Appearance:No significant abnormality Inductance change: Within ±10% Q change: Within ±20% MCOILTM MC series※ Appearance:No significant abnormality Inductance change: Within ±10% Temperature : Maximum operating temperature Applied current :Rated current ※MC series ; Idc2max Duration :500 +24/-0 hrs Recovery :2 to 3 hrs of recovery under the standard condition after the removal from test chamber. (See Note 1) Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E08R01 Precautions on the use of Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils(MC series F type) ■PRECAUTIONS 1. Circuit Design Precautions ◆Verification of operating environment, electrical rating and performance 1. A malfunction in medical equipment, spacecraft, nuclear reactors, etc. may cause serious harm to human life or have severe social ramifications. As such, any inductors to be used in such equipment may require higher safety and/or reliability considerations and should be clearly differentiated from components used in general purpose applications. ◆Operating Current(Verification of Rated current) 1. The operating current including inrush current for inductors must always be lower than their rated values. 2. Do not apply current in excess of the rated value because the inductance may be reduced due to the magnetic saturation effect. 2. PCB Design Precautions ◆Pattern configurations(Design of Land-patterns) 1. When inductors are mounted on a PCB, the size of land patterns and the amount of solder used(size of fillet)can directly affect inductor performance. Therefore, the following items must be carefully considered in the design of solder land patterns: (1) The amount of solder applied can affect the ability of chips to withstand mechanical stresses which may lead to breaking or cracking. Therefore, when designing land-patterns it is necessary to consider the appropriate size and configuration of the solder pads which in turn determines the amount of solder necessary to form the fillets. (2) When more than one part is jointly soldered onto the same land or pad, the pad must be designed so that each component's soldering point is separated by solder-resist. (3) The larger size of land patterns and amount of solder, the smaller Q value after mounting on PCB. It makes higher the Q value to design land patterns smaller than terminal electrode of chips. ◆Pattern configurations(Inductor layout on panelized[ breakaway] PC boards) 1. After inductors have been mounted on the boards, chips can be subjected to mechanical stresses in subsequent manufacturing processes (PCB cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering the reflow soldered boards etc.)For this reason, planning pattern configurations and the position of SMD inductors should be carefully performed to minimize stress. ◆Pattern configurations(Design of Land-patterns) 1. The following diagrams and tables show some examples of recommended patterns to prevent excessive solder amounts(larger fillets which extend above the component end terminations). Examples of improper pattern designs are also shown. (1) Recommended land dimensions for a typical chip inductor land patterns for PCBs ●Recommended land dimensions for Multilayer inductor Wave-soldering (Unit:mm) Type 1608 2012 2125 2016 L 1.6 2.0 2.0 2.0 Size W 0.8 1.25 1.25 1.6 A 0.8~1.0 1.0~1.4 1.0~1.4 1.0~1.4 B 0.5~0.8 0.8~1.5 0.8~1.5 0.8~1.5 C 0.6~0.8 0.9~1.2 0.9~1.2 1.3~1.6 Land pattern Solder-resist Chip inductor 2520 2.5 2.0 1.0~1.4 0.6~1.0 1.6~2.0 3216 3.2 1.6 1.8~2.5 0.8~1.7 1.2~1.6 C B A B Chip inductor W Technical considerations Reflow-soldering (Unit:mm) Type 0603 1005 L 0.6 1.0 Size W 0.3 0.5 A 0.20~0.30 0.45~0.55 B 0.20~0.30 0.40~0.50 C 0.25~0.40 0.45~0.55 L 105 1.0 0.6 0.50~0.55 0.30~0.40 0.60~0.70 ●Recommended land dimension for Array type (Unit:mm) Type L Size W a b c d 2010 2.0 1.0 0.5~0.6 0.5~0.6 0.2~0.3 0.5 3216 3.2 1.6 0.7~0.9 0.8~1.0 0.4~0.5 0.8 1608 1.6 0.8 0.8~1.0 0.6~0.8 0.6~0.8 2012 2.0 1.25 0.8~1.2 0.8~1.2 0.9~1.6 c 2125 2.0 1.25 0.8~1.2 0.8~1.2 0.9~1.6 2016 2.0 1.6 0.8~1.2 0.8~1.2 1.2~2.0 2520 2.5 2.0 1.0~1.4 0.6~1.0 1.8~2.2 3216 3.2 1.6 1.8~2.5 0.6~1.5 1.2~2.0 d a W b a L ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01 ●Recommended land dimension for Multilayer common mode choke coil (Unit:mm) c Type 0605 0806 L 0.65 0.85 Size a W 0.50 0.65 a a 0.27~0.30 0.25~0.35 W d b b 0.17~0.20 0.25~0.35 c 0.20~0.26 0.25~0.35 a d 0.4 0.5 L (Unit:mm) c Type L Size W a b c d 1210 1.0 1.25 0.45~0.55 0.7~0.8 0.25~0.35 0.55 a b d W a L (2) Examples of good and bad solder application Item Not recommended Recommended Lead wire of component Solder-resist Mixed mounting of SMD and leaded components Chassis Solder (for grounding) Solder-resist Component placement close to the chassis Electrode pattern Lead wire of component Soldering iron Hand-soldering of leaded components near mounted components Solder-resist Solder-resist Horizontal component placement ◆Pattern configurations(Inductor layout on panelized[ breakaway] PC boards) 1-1. The following are examples of good and bad inductor layout; SMD inductors should be located to minimize any possible mechanical stresses from board warp or deflection. Item Not recommended Recommended Position the component at a right angle to the direction of the mechanical stresses that are anticipated. Deflection of the board 1-2. To layout the inductors for the breakaway PC board, it should be noted that the amount of mechanical stresses given will vary depending on inductor layout. An example below should be counted for better design. E D Perforation C A B Slit Magnitude of stress A>B=C>D>E 1-3. When breaking PC boards along their perforations, the amount of mechanical stress on the inductors can vary according to the method used. The following methods are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, any ideal SMD inductor layout must also consider the PCB splitting procedure. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01 3. Considerations for automatic placement Precautions ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the inductors when mounting onto the PC boards. 2. The maintenance and inspection of the mounter should be conducted periodically. ◆Selection of Adhesives 1. Mounting inductors with adhesives in preliminary assembly, before the soldering stage, may lead to degraded inductor characteristics unless the following factors are appropriately checked; the size of land patterns, type of adhesive, amount applied, hardening temperature and hardening period. Therefore, it is imperative to consult the manufacturer of the adhesives on proper usage and amounts of adhesive to use. ◆Adjustment of mounting machine 1. If the lower limit of the pick-up nozzle is low, too much force may be imposed on the inductors, causing damage. To avoid this, the following points should be considered before lowering the pick-up nozzle: (1) The lower limit of the pick-up nozzle should be adjusted to the surface level of the PC board after correcting for deflection of the board. (2) The pick-up pressure should be adjusted between 1 and 3N static loads. (3) To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins should be used under the PC board. The following diagrams show some typical examples of good pick-up nozzle placement: Item Improper method Proper method Single-sided mounting chipping or cracking supporting pins or back-up pins Double-sided mounting chipping or cracking Technical considerations supporting pins or back-up pins 2. As the alignment pin wears out, adjustment of the nozzle height can cause chipping or cracking of the inductors because of mechanical impact on the inductors. To avoid this, the monitoring of the width between the alignment pin in the stopped position, and maintenance, inspection and replacement of the pin should be conducted periodically. ◆Selection of Adhesives 1. Some adhesives may cause reduced insulation resistance. The difference between the shrinkage percentage of the adhesive and that of the inductors may result in stresses on the inductors and lead to cracking. Moreover, too little or too much adhesive applied to the board may adversely affect component placement, so the following precautions should be noted in the application of adhesives. (1) Required adhesive characteristics a. The adhesive should be strong enough to hold parts on the board during the mounting & solder process. b. The adhesive should have sufficient strength at high temperatures. c. The adhesive should have good coating and thickness consistency. d. The adhesive should be used during its prescribed shelf life. e. The adhesive should harden rapidly. f. The adhesive must not be contaminated. g. The adhesive should have excellent insulation characteristics. h. The adhesive should not be toxic and have no emission of toxic gasses. (2) When using adhesives to mount inductors on a PCB, inappropriate amounts of adhesive on the board may adversely affect component placement. Too little adhesive may cause the inductors to fall off the board during the solder process. Too much adhesive may cause defective soldering due excessive flow of adhesive on to the land or solder pad. Amount of adhesives After inductors are bonded [Recommended conditions] a a Figure 0805 case sizes as examples a 0.3mm min b b 100~120μm c Area with no adhesive c c ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01 4. Soldering Precautions ◆Selection of Flux 1. Since flux may have a significant effect on the performance of inductors, it is necessary to verify the following conditions prior to use; (1) Flux used should be with less than or equal to 0.1 wt% (Chlorine conversion method) of halogenated content. Flux having a strong acidity content should not be applied. (2) When soldering inductors on the board, the amount of flux applied should be controlled at the optimum level. (3) When using water-soluble flux, special care should be taken to properly clean the boards. ◆Soldering 1. Temperature, time, amount of solder, etc. are specified in accordance with the following recommended conditions, and please contact us about peak temperature when you use lead-free paste. ◆Selection of Flux 1-1. When too much halogenated substance(Chlorine, etc.)content is used to activate the flux, or highly acidic flux is used, an excessive amount of residue after soldering may lead to corrosion of the terminal electrodes or degradation of insulation resistance on the surface of the Inductor. 1-2. Flux is used to increase solderability in flow soldering, but if too much is applied, a large amount of flux gas may be emitted and may detrimentally affect solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system. 1-3. Since the residue of water-soluble flux is easily dissolved by water content in the air, the residue on the surface of Inductor in high humidity conditions may cause a degradation of insulation resistance and therefore affect the reliability of the components. The cleaning methods and the capability of the machines used should also be considered carefully when selecting water-soluble flux. ◆Soldering 1-1. Preheating when soldering Preheating: Inductors shall be preheated sufficiently, and the temperature difference between the inductors and solder shall be within 130°C. Cooling: The temperature difference between the components and cleaning process should not be greater than 100℃. Inductors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. Therefore, the soldering process must be conducted with a great care so as to prevent malfunction of the components due to excessive thermal shock. [Reflow soldering] 【Recommended condition for Pb-free soldering】 Temperature(℃) 300 Technical considerations Peak 260℃ Max. Within 10sec. 200 Slow cooling 100 0 Preheating150℃ Heating above 230℃ 60sec. Min. 40sec. Max. [Wave soldering] 【Recommended condition for Pb-free soldering】 Temperature(℃) 300 200 Peak 260℃ Max. Within 10sec. 120sec. Min. Preheating 150℃ 100 Slow cooling Caution 1. Solder (fillet) should wet up to 1/2 to 1/3 of the thickness of an inductor ideally as shown below: 1/2T~1/3T Inductor Solder T PC board 2. Because excessive dwell time can detrimentally affect solderability, soldering duration shall be kept as close to recommended time as possible. 3. The allowable number of reflow soldering is two (2) times. Caution 1. Make sure the inductors are preheated sufficiently. 2. The temperature difference between the inductor and melted solder should be within 130℃. 3. Cooling after soldering should be as gradual as possible. 4. The allowable number of wave soldering is one (1) time. 5. Wave soldering must not be applied to the inductors designated as for reflow soldering only. 0 [Hand soldering] 【Recommended condition for Pb-free soldering】 400 Peak 350℃ Max. Within 3sec. Temperature(℃) 300 ⊿T Caution 1. It is recommended to use a 20W soldering iron with a maximum tip diameter of 1.0 mm. 2. The soldering iron shall not directly touch inductors 3. The allowable number of hand soldering is one (1) time Slow cooling 200 100 0 Preheating 150℃ Min. 60sec. Min. (※⊿T≦150℃) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01 5. Cleaning Precautions ◆Cleaning conditions 1. When cleaning the PC board after the Inductors are all mounted, select the appropriate cleaning solution according to the type of flux used and purpose of the cleaning(e.g. to remove soldering flux or other materials from the production process.) 2. Cleaning conditions should be determined after verifying, through a test run, that the cleaning process does not affect the inductor's characteristics. Technical considerations ◆Cleaning conditions 1. The use of inappropriate solutions can cause foreign substances such as flux residue to adhere to the inductor, resulting in a degradation of the inductor's electrical properties(especially insulation resistance). 2. Inappropriate cleaning conditions(insufficient or excessive cleaning)may detrimentally affect the performance of the inductors. In the case of ultrasonic cleaning, too much power output can cause excessive vibration of the PC board which may lead to the cracking of the inductor or the soldered portion, or decrease the terminal electrodes' strength. Therefore, the following conditions should be carefully checked; Ultrasonic output 20W/ℓ or less Ultrasonic frequency 40kHz or less Ultrasonic washing period 5 min. or less 6. Resin coating and mold Precautions 1. With some type of resins a decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while left under normal storage conditions resulting in the deterioration of the inductor's performance. 2. Thermal expansion and thermal shrinkage characteristics of resins may lead to the deterioration of inductors’ performance. 3. When a resin hardening temperature is higher than inductor operating temperature, the stresses generated by the excessive heat may lead to damage in inductors. 7. Handling Precautions ◆Breakaway PC boards(splitting along perforations) 1. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆General handling precautions ・Always wear static control bands to protect against ESD. ・ Keep the inductors away from all magnets and magnetic objects. ・ Use non-magnetic tweezers when handling inductors. ・ Any devices used with the inductors( soldering irons, measuring instruments) should be properly grounded. ・ Keep bare hands and metal products(i.e., metal desk)away from inductor electrodes or conductive areas that lead to chip electrodes. ・ Keep inductors away from items that generate magnetic fields such as speakers or coils. ◆Mechanical considerations Be careful not to subject the inductors to excessive mechanical shocks. (1) If inductors are dropped on the floor or a hard surface they should not be used. (2) When handling the mounted boards, be careful that the mounted components do not come in contact with or bump against other boards or components. 8. Storage conditions Precautions ◆Storage To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control temperature and humidity in the storage area. Humidity should especially be kept as low as possible. ・Recommended conditions Ambient temperature: 30℃ or below Humidity: 70% RH or below The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of inductor is deteriorated as time passes, so inductors should be used within 6 months from the time of delivery. ・Inductor should be kept where no chlorine or sulfur exists in the air. Technical considerations ◆Storage If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. For this reason, components should be used within 6 months from the time of delivery. If exceeding the above period, please check solderability before using the inductors. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E08R01
BK1608HS330-T 价格&库存

很抱歉,暂时无法提供与“BK1608HS330-T”相匹配的价格&库存,您可以联系我们找货

免费人工找货