BK1608LM252-T

[ For General Electronic Equipment (General Environment) ] Notice for TAIYO YUDEN Products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or use of our products. Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. ■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification sheets are available. ■ Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our products. ■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information network equipment including, without limitation, telephone exchange, and base station). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control equipment, undersea equipment, military equipment). *Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter“TAIYO YUDEN’ s official sales channel” ). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’ s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export Administration Regulations” ,“Foreign Exchange and Foreign Trade Control Law”of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 18 MULTILAYER CHIP BEAD INDUCTORS(BK SERIES) MULTILAYER CHIP BEAD INDUCTORS（BK SERIES） WAVE＊ WAVE* REFLOW REFLOW ＊Except for BK0402, BK0603, BK1005 *Except for BK0402, BK0603, BK1005 ■PARTS NUMBER B K △ ① 1 * Operating Temp.：-55～+125℃ 6 0 8 H ② ①Series name Code BK△ S 1 2 1 ④ ③ － T △ ⑤ ⑥ ⑦ ④Nominal impedance Code （example） 150 101 102 Series name Multilayer chip bead inductor ②Dimensions（L×W） Type（inch） 0402 0603 1005 1608 2125 0402（01005） 0603（0201） 1005（0402） 1608（0603） 2125（0805） ③Material Code HW HS HR HM LM LL TS TM Dimensions （L×W）［mm］ 0.4×0.2 0.6×0.3 1.0×0.5 1.6×0.8 2.0×1.25 Nominal impedance［Ω］ ⑤Characteristics Code － 15 100 1000 Characteristics Standard ⑥Packaging Code T Packaging Taping Material ⑦Internal code Code △ Internal code Standard Refer to impedance curves for material differences ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY W L T e Type L W T e BK 0402 （01005） BK 0603 （0201） BK 1005 （0402） BK 1608 （0603） 0.40±0.02 （0.016±0.001） 0.60±0.03 （0.024±0.001） 1.00±0.05 （0.039±0.002） 1.6±0.15 （0.063±0.006） 2.0＋0.3/－0.1 （0.079＋0.012/－0.004） 2.0＋0.3/－0.1 （0.079＋0.012/－0.004） 0.20±0.02 （0.008±0.001） 0.30±0.03 （0.012±0.001） 0.50±0.05 （0.020±0.002） 0.8±0.15 （0.031±0.006） 1.25±0.2 （0.049±0.008） 1.25±0.2 （0.049±0.008） 0.20±0.02 （0.008±0.001） 0.30±0.03 （0.012±0.001） 0.50±0.05 （0.020±0.002） 0.8±0.15 （0.031±0.006） 0.85±0.2 （0.033±0.008） 1.25±0.2 （0.049±0.008） 0.10＋0.04/－0.03 （0.004＋0.002/－0.001） 0.15±0.05 （0.006±0.002） 0.25±0.10 （0.010±0.004） 0.3±0.2 （0.012±0.008） 0.5±0.3 （0.020±0.012） 0.5±0.3 （0.020±0.012） BK 2125 （0805） Standard quantity［pcs］ Paper tape Embossed tape 20000 － 15000 － 10000 － 4000 － 4000 － － 2000 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Code △＝Blank space Unit：mm（inch） i_mlci_BK_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 115 ■PARTS NUMBER ●BK 0402 Parts number BK 0402HS100-T BK 0402HS700-T BK 0402HS121-T BK 0402HM100-T BK 0402HM750-T BK 0402HM121-T BK 0402HM151-T BK 0402HM181-T BK 0402HM241-T BK 0402HM331-T BK 0402LL220-T BK 0402LL470-T BK 0402LL101-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 10 70 120 10 75 120 150 180 240 330 22 47 100 Impedance tolerance ±5Ω ±25％ ±25％ ±5Ω ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.10 0.37 0.53 0.07 0.45 0.60 0.65 0.75 0.90 1.20 0.70 1.10 2.00 Rated current ［mA］（max.） 540 280 240 750 260 220 200 200 200 150 150 120 100 Thickness ［mm］ 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.065 0.070 0.40 0.45 0.65 1.20 0.25 0.40 0.80 1.05 1.20 0.23 0.38 0.80 1.15 1.30 0.25 0.45 0.55 0.70 1.00 1.30 1.50 0.18 0.23 0.32 0.75 0.18 0.23 0.38 0.85 Rated current ［mA］（max.） 500 500 200 200 200 150 200 200 200 100 100 450 350 250 220 200 200 200 150 150 100 100 100 500 450 400 270 450 400 300 250 Thickness ［mm］ 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.17 0.24 0.31 0.50 0.60 0.03 0.06 0.10 0.10 0.20 0.30 0.45 0.55 0.58 0.60 0.18 0.18 0.30 0.45 0.50 0.70 0.11 0.18 0.25 0.33 0.31 0.45 0.50 0.70 0.90 Rated current ［mA］（max.） 500 450 400 350 300 1,000 700 700 700 500 400 350 300 300 300 350 300 300 250 250 150 500 400 400 350 400 350 300 250 120 Thickness ［mm］ 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 ●BK 0603 Parts number ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS BK 0603HS220-T BK 0603HS330-T BK 0603HS800-T BK 0603HS121-T BK 0603HS241-T BK 0603HS601-T BK 0603HM600-T BK 0603HM121-T BK 0603HM241-T BK 0603HM471-T BK 0603HM601-T BK 0603HR121-T BK 0603HR241-T BK 0603HR601-T BK 0603HR102-T BK 0603HR122-T BK 0603LL100-T BK 0603LL220-T BK 0603LL330-T BK 0603LL470-T BK 0603LL560-T BK 0603LL800-T BK 0603LL121-T BK 0603TS800-T BK 0603TS121-T BK 0603TS241-T BK 0603TS601-T BK 0603TM800-T BK 0603TM121-T BK 0603TM241-T BK 0603TM601-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 22 33 80 120 240 600 60 120 240 470 600 120 240 600 1000 1200 10 22 33 47 56 80 120 80 120 240 600 80 120 240 600 Impedance tolerance ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ●BK 1005 Parts number BK 1005HW680-T BK 1005HW121-T BK 1005HW241-T BK 1005HW431-T BK 1005HW601-T BK 1005HS100-T BK 1005HS330-T BK 1005HS680-T BK 1005HS800-T BK 1005HS121-T BK 1005HS241-T BK 1005HS431-T BK 1005HS601-T BK 1005HS102-T BK 1005HR601-T BK 1005HM750-T BK 1005HM121-T BK 1005HM241-T BK 1005HM471-T BK 1005HM601-T BK 1005HM102-T BK 1005LL100-T BK 1005LL220-T BK 1005LL330-T BK 1005LL470-T BK 1005LL680-T BK 1005LL121-T BK 1005LL181-T BK 1005LL241-T BK 1005LM182-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 68 120 240 430 600 10 33 68 80 120 240 430 600 1000 600 75 120 240 470 600 1000 10 22 33 47 68 120 180 240 1800 Impedance tolerance ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ i_mlci_BK_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 116 18 ■PARTS NUMBER ●BK 1608 Parts number RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 120 240 430 600 22 33 47 60 80 120 240 600 1000 120 240 470 600 1000 30 47 56 68 120 180 240 330 430 510 680 750 1500 1800 2500 430 600 1000 Impedance tolerance ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.15 0.25 0.30 0.40 0.05 0.08 0.10 0.10 0.10 0.18 0.25 0.45 0.60 0.20 0.35 0.45 0.60 0.70 0.20 0.30 0.30 0.35 0.50 0.65 0.80 0.85 0.85 0.90 1.00 0.60 0.75 0.85 1.10 0.21±30％ 0.27±30％ 0.30±30％ Rated current ［mA］（max.） 600 450 400 300 1,500 1,200 900 800 600 500 400 350 300 350 300 250 250 200 500 400 400 300 300 250 250 200 200 200 150 300 250 200 200 400 350 300 Thickness ［mm］ 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.05 0.05 0.05 0.05 0.10 0.10 0.15 0.20 0.25 0.30 0.40 0.15 0.20 0.25 0.25 0.35 0.20 0.30 0.35 0.30 0.35 0.45 0.75 Rated current ［mA］（max.） 1,200 1,200 1,200 1,000 1,000 900 800 600 500 500 300 800 600 500 500 400 600 400 300 400 400 300 200 Thickness ［mm］ 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 1.25 ±0.2 1.25 ±0.2 ●BK 2125 Parts number BK 2125HS150-T BK 2125HS220-T BK 2125HS330-T BK 2125HS470-T BK 2125HS750-T BK 2125HS101-T BK 2125HS121-T BK 2125HS241-T BK 2125HS431-T BK 2125HS601-T BK 2125HS102-T BK 2125HM121-T BK 2125HM241-T BK 2125HM471-T BK 2125HM601-T BK 2125HM102-T BK 2125LL560-T BK 2125LL121-T BK 2125LL241-T BK 2125LM751-T BK 2125LM152-T BK 2125LM182-T BK 2125LM252-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 15 22 33 47 75 100 120 240 430 600 1000 120 240 470 600 1000 56 120 240 750 1500 1800 2500 Impedance tolerance ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS BK 1608HW121-T BK 1608HW241-T BK 1608HW431-T BK 1608HW601-T BK 1608HS220-T BK 1608HS330-T BK 1608HS470-T BK 1608HS600-T BK 1608HS800-T BK 1608HS121-T BK 1608HS241-T BK 1608HS601-T BK 1608HS102-T BK 1608HM121-T BK 1608HM241-T BK 1608HM471-T BK 1608HM601-T BK 1608HM102-T BK 1608LL300-T BK 1608LL470-T BK 1608LL560-T BK 1608LL680-T BK 1608LL121-T BK 1608LL181-T BK 1608LL241-T BK 1608LL331-T BK 1608LL431-T BK 1608LL511-T BK 1608LL681-T BK 1608LM751-T BK 1608LM152-T BK 1608LM182-T BK 1608LM252-T BK 1608TS431-T BK 1608TS601-T BK 1608TS102-T EHS i_mlci_BK_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 117 ■ ELECTRICAL CHARACTERISTICS ■ BK0402 BK0402 HS700 80 200 200 25 60 40 10 100 1000 Frequency [MHz] 0 10000 Ｒ 10 100 1000 Frequency [MHz] 0 10000 250 200 200 150 Ｚ Ｒ 10 100 1000 Frequency [MHz] Ｘ 10 100 1000 Frequency [MHz] BK0402 HM241 Ｚ Ｒ 100 250 Ｚ Ｒ 200 150 100 Ｘ 10 100 1000 Frequency [MHz] 1 10 100 1000 Frequency [MHz] 10 100 1000 Frequency [MHz] 250 Ｒ 200 150 Ｘ 0 10000 BK0402 LL220 BK0402 HM331 1 10 100 1000 Frequency [MHz] 10000 BK0402 LL470 400 250 350 200 400 Ｒ 300 200 Ｘ 0 1 300 Impedance ［Ω］ Ｚ 500 Ｒ 150 Ｚ 100 10 100 1000 Frequency [MHz] 0 10000 Ｚ 250 200 Ｒ 150 100 50 100 10000 Ｚ 300 50 0 1 10000 Impedance ［Ω］ Impedance ［Ω］ Impedance ［Ω］ Ｒ Ｘ BK0402 HM181 100 50 Ｘ 1 400 200 10000 350 700 Ｚ 10 100 1000 Frequency [MHz] 400 600 0 Ｒ Ｘ 1 450 300 150 0 10000 500 100 Ｚ 10 0 10000 BK0402 HM151 350 50 50 50 Ｘ 1 10 100 1000 Frequency [MHz] 0 10000 Ｘ 1 10 100 1000 Frequency [MHz] 10000 ■ BK0603 BK0603 HS220 Impedance ［Ω］ Ｚ 500 400 300 Ｒ 200 100 80 80 60 40 Ｚ 20 Ｒ 100 0 Ｘ 1 10 100 1000 Frequency [MHz] 0 10000 150 40 10 100 1000 Frequency [MHz] 10000 Impedance ［Ω］ 800 150 R Z X 1 1000 1 10000 500 200 400 Impedance ［Ω］ 250 150 100 50 10 100 1000 10000 100 1000 R 200 X 0 1 10 100 1000 Frequency［MHz］ 200 1 10000 1 10 100 1000 10000 50 X 10000 BK0603 HM471 1000 BK0603 HM601 800 Z 600 R 400 0 1000 100 10 100 1000 Frequency［MHz］ 200 10000 100 150 800 300 10 250 Z 1000 Z 1 200 400 0 10000 BK0603 HM241 100 1 10 10000 600 R Impedance ［Ω］ 100 10 100 1000 Frequency［MHz］ BK0603 HS601 X 10 R Z 50 X 0 200 1 100 Z R 1000 50 200 60 250 100 250 20 Ｘ 1 BK0603 HS330 Impedance[ ] 600 100 Impedance ［Ω］ BK0402 LL101 700 Impedance ［Ω］ ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Impedance ［Ω］ 250 300 15 Ｘ 1 BK0402 HM121 300 1 20 50 Ｘ 1 BK0402 HM750 100 Ｚ 100 BK0402 HM100 5 300 0 Ｒ 50 Ｒ Ｘ 1 Ｚ Impedance ［Ω］ 0 100 150 Impedance ［Ω］ Ｚ 150 Impedance ［Ω］ 30 Impedance ［Ω］ 250 20 Impedance ［Ω］ BK0402 HS121 250 Impedance ［Ω］ Impedance ［Ω］ BK0402 HS100 100 10 100 1000 Frequency［MHz］ Z 400 R 200 Ｘ 1 600 Ｘ 10000 0 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 118 18 ■ ELECTRICAL CHARACTERISTICS 100 80 40 250 200 150 100 Ｘ 20 50 0 0 1 Ｒ 10 100 1000 Frequency [MHz] 10000 1 BK0603 HR122 2000 1500 500 150 100 Z Ｘ BK0603 LL470 10000 BK0603 LL220 1 10 100 1000 Frequency［MHz］ 400 150 100 0 10000 BK0603 LL560 500 BK0603 LL330 500 Z Ｒ 300 200 Z Ｒ 100 Ｘ R 0 R 0 10 100 1000 Frequency [MHz] 50 X 500 Ｘ 250 R 0 500 300 200 50 Ｘ 400 1000 1 10 100 1000 Frequency［MHz］ X 0 10000 BK0603 LL800 1000 1 10 100 1000 Frequency［MHz］ 10000 BK0603 LL121 1000 Z Z 200 R 100 300 Impedance ［Ω］ 300 800 R 200 100 800 600 Impedance ［Ω］ 400 Impedance ［Ω］ Impedance ［Ω］ 400 Z R 400 200 600 Z Ｒ 400 200 X 10 100 1000 Frequency［MHz］ 0 10000 BK0603 TS800 200 R 50 1 Ｚ 100 10 100 1000 Frequency［MHz］ 0 10000 BK0603 TM800 200 Ｒ 1 10 100 1000 Frequency［MHz］ 10000 BK0603 TM121 50 Ｚ 100 Ｒ 50 X 1 10 100 1000 Frequency［MHz］ 0 10000 Ｚ 200 1 10 100 1000 Frequency［MHz］ 1 10 100 1000 Frequency［MHz］ 10000 Ｚ 400 Ｒ Ｘ 1 10 100 1000 Frequency［MHz］ 10000 BK0603 TM601 1000 800 300 Ｚ 200 0 10000 600 0 BK0603 TM241 100 Ｘ 10000 BK0603 TS601 200 Ｒ Ｘ 400 150 10 100 1000 Frequency［MHz］ 800 500 Impedance ［Ω］ Impedance ［Ω］ R Z Ｘ 1 1000 300 0 200 100 BK0603 TS241 100 Ｘ 250 150 Impedance ［Ω］ 150 50 X 0 10000 400 Impedance ［Ω］ Impedance ［Ω］ Impedance ［Ω］ Z 1 500 200 100 0 0 10000 BK0603 TS121 250 150 0 1 Impedance ［Ω］ 1 X 10 100 1000 Frequency［MHz］ Impedance ［Ω］ 0 X 10 100 1000 Frequency［MHz］ 10 100 1000 Frequency［MHz］ Ｚ 400 200 Ｒ Ｘ 1 600 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Impedance ［Ω］ 1000 Ｒ 500 01 10000 200 Z 600 100 10 100 1000 Frequency [MHz] BK0603 LL100 250 700 200 Ｘ Z Ｚ 800 Impedance[ ] Ｚ Impedance ［Ω］ Impedance ［Ω］ Impedance ［Ω］ Ｒ 120 BK0603 HR102 1500 900 300 140 BK0603 HR601 1000 350 Ｚ 160 Impedance[ ] BK0603 HR241 400 Impedance ［Ω］ 180 Impedance ［Ω］ BK0603 HR121 200 0 10000 Ｘ 1 Ｒ 10 100 1000 Frequency［MHz］ 10000 ■ BK1005 100 Z 50 R 1 150 Ｚ 100 Ｒ 50 X 10 100 1000 Frequency［MHz］ 10000 0 800 1 10 100 1000 Frequency［MHz］ 300 200 Z R 100 Ｘ BK1005 HW431 1000 400 Impedance ［Ω］ Impedance ［Ω］ Impedance ［Ω］ 150 BK1005 HW241 500 200 200 0 BK1005 HW121 250 Impedance ［Ω］ BK1005 HW680 250 600 400 Z X X 10000 0 1 R 200 10 100 1000 Frequency［MHz］ 10000 0 1 10 100 1000 Frequency［MHz］ 10000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 119 ■ ELECTRICAL CHARACTERISTICS Z 400 R 60 40 20 200 0 1 10 100 1000 Frequency［MHz］ BK1005 HS800 1 40 R Z 100 0 10000 1 10 100 0 10000 800 150 150 100 R 50 0 10 100 1000 Frequency［MHz］ Z 0 10000 Impedance ［Ω］ 1 R X 10 100 1000 Frequency［MHz］ BK1005 HR601 BK1005 HS102 10000 BK1005 HM750 1000 200 800 150 600 100 1000 400 Z 50 200 0 BK1005 HM121 BK1005 HS431 200 2000 250 10000 400 0 1 10 100 1000 Frequency［MHz］ 600 X R 1 0 X 10 100 1000 Frequency［MHz］ 10000 10 10000 0 500 400 200 Impedance ［Ω］ ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Impedance ［Ω］ 200 50 1 Frequency［MHz］ 200 Z Ｒ X 1000 1000 100 Z 50 X X 10 100 1000 Frequency［MHz］ 150 250 250 Impedance ［Ω］ 0 10000 200 60 20 Z R X BK1005 HS680 250 80 Impedance ［Ω］ Impedance ［Ω］ 600 BK1005 HS330 100 80 800 Impedance ［Ω］ BK1005 HS100 100 Impedance ［Ω］ BK1005 HW601 1000 Z 150 300 R 100 200 50 100 0 1 X 10 100 1000 Frequency［MHz］ 0 1 10000 BK1005 HM102 100 1000 BK1005 LL220 BK1005 LL100 2000 BK1005 LL330 250 500 200 400 150 300 100 200 50 50 100 0 0 250 200 150 1000 100 0 1 10 100 1000 10000 1 10 100 1000 10000 1 10 100 1000 10000 0 1 10 100 1000 10000 BK1005 LL470 500 BK1005 LL680 500 400 400 300 300 200 200 100 100 0 0 1 10 100 1000 10000 1 10 100 1000 10000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 120 18 ■ ELECTRICAL CHARACTERISTICS ■ BK1608 BK1005 LM182 2500 2000 1500 Z 1000 R 500 X 0 1 10 100 1000 10000 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS BK1608 LL300 BK1608 LL470 BK1608 LL560 BK1608 LL680 500 500 500 500 250 250 250 250 0 0 1 10 100 1000 10000 0 0 1 10 100 1000 10000 1 10 100 1000 10000 1 10 100 1000 10000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 121 ■ ELECTRICAL CHARACTERISTICS BK1608 LL121 1500 4000 750 2000 0 1 10 100 1000 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS ■ BK2125 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 122 18 ■ ELECTRICAL CHARACTERISTICS 1000 Z 500 R X 0 1 10 100 1000 1000 Z R 500 X 1 10 100 1000 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS 0 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 18 123 Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils（MC series F type） Metal Multilayer Chip Power Inductors (MCOILTM MC series) ■PACKAGING ①Minimum Quantity ●Tape & Reel Packaging Type CK1608（0603） CK2125（0805） CKS2125（0805） CKP1608（0603） CKP2012（0805） CKP2016（0806） CKP2520（1008） NM2012（0805） NM2520（1008） LK1005（0402） LK1608（0603） LK2125（0805） HK0603（0201） HK1005（0402） HK1608（0603） HK2125（0805） HKQ0402（01005） HKQ0603W（0201） HKQ0603S（0201） HKQ0603U（0201） AQ105（0402） BK0402（01005） BK0603（0201） BK1005（0402） BKH0603（0201） BKH1005（0402） BK1608（0603） BK2125（0805） BK2010（0804） BK3216（1206） BKP0402（01005） BKP0603（0201） BKP1005（0402） BKP1608（0603） BKP2125（0805） MCF0605（0202） MCF0806（0302） MCF1210（0504） MCF2010（0804） MCFK1608(0603) MCFE1608（0603） MCKK1608（0603） MCHK2012(0806) MCKK2012（0805） Thickness mm（inch） 0.8 （0.031） 0.85（0.033） 1.25（0.049） 0.85（0.033） 1.25（0.049） 0.8 （0.031） 0.9 （0.035） 0.9 （0.035） 0.7 （0.028） 0.9 （0.035） 1.1 （0.043） 0.9 （0.035） 0.9 （0.035） 1.1 （0.043） 0.5 （0.020） 0.8 （0.031） 0.85（0.033） 1.25（0.049） 0.3 （0.012） 0.5 （0.020） 0.8 （0.031） 0.85（0.033） 1.0 （0.039） 0.2 （0.008） 0.3 （0.012） 0.3 （0.012） 0.3 （0.012） 0.5 （0.020） 0.2 （0.008） 0.3 （0.012） 0.5 （0.020） 0.3 （0.012） 0.5 （0.020） 0.8 （0.031） 0.85（0.033） 1.25（0.049） 0.45（0.018） 0.8 （0.031） 0.2 （0.008） 0.3 （0.012） 0.5 （0.020） 0.8 （0.031） 0.85（0.033） 0.3 （0.012） 0.4 （0.016） 0.55（0.022） 0.45（0.018） 0.6 (0.024) 0.65（0.026） 1.0（0.039） 0.8 (0.031) 1.0（0.039） Standard Quantity ［pcs］ Paper Tape Embossed Tape 4000 － 4000 － － 2000 4000 － － 2000 4000 － － 3000 － 3000 － 3000 － 3000 － 2000 － 3000 － 3000 － 2000 10000 － 4000 － 4000 － － 2000 15000 － 10000 － 4000 － － 4000 － 3000 20000 40000 15000 － 15000 － 15000 － 10000 － 20000 － 15000 － 10000 － 15000 － 10000 － 4000 － 4000 － － 2000 4000 － － 4000 20000 － 15000 － 10000 － 4000 － 4000 － 15000 － － 10000 － 5000 － 4000 4000 － 4000 － 3000 4000 － 3000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E06R01 ②Taping material ●Card board carrier tape Top tape Base tape Sprocket hole Bottom tape Chip cavity CK CKP CK CKS LK LK LK HK HK HK HKQ HKQ AQ 1608 1608 2125 2125 1005 1608 2125 0603 1005 1608 0402 0603 105 BK BK BK BK BK BK BKP BKP BKP BKP BKP BKH BKH MCF MC MC 0402 0603 1005 1608 2125 2010 0402 0603 1005 1608 2125 0603 1005 0605 1608 2012 CK CKS CKP CKP CKP NM NM LK HKQ HK 2125 2125 2012 2016 2520 2012 2520 2125 0402 2125 BK BK MCF MCF MCF MC MC 2125 3216 0806 1210 2010 1608 2012 Chip Filled Chip ●Embossed Tape Top tape Sprocket hole Base tape Chip cavity Chip Filled Chip ③Taping Dimensions ●Paper tape (8mm wide) B T 8.0±0.3 (0.315±0.012) A F Unit：mm（inch） 1.75±0.1 (0.069±0.004） 3.5±0.05 (0.138±0.002) Sprocket hole φ1.5＋0.1/－0 (φ0.059＋0.004/-0) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E06R01 Type Thickness mm（inch） CK1608（0603） 0.8 （0.031） CK2125（0805） 0.85（0.033） CKS2125（0805） 0.85（0.033） CKP1608（0603） 0.8 （0.031） LK1005（0402） 0.5 （0.020） LK1608（0603） 0.8 （0.031） LK2125（0805） 0.85（0.033） HK0603（0201） 0.3 （0.012） HK1005（0402） 0.5 （0.020） HK1608（0603） 0.8 （0.031） HKQ0402（01005） 0.2 （0.008） HKQ0603W（0201） 0.3 （0.012） HKQ0603S（0201） 0.3 （0.012） HKQ0603U（0201） 0.3 （0.012） AQ105（0402） 0.5 （0.020） BK0402（01005） 0.2 （0.008） BK0603（0201） 0.3 （0.012） BK1005（0402） 0.5 （0.020） BK1608（0603） 0.8 （0.031） BK2125（0805） 0.85（0.033） BK2010（0804） 0.45（0.018） BKP0402（01005） 0.2 （0.008） BKP0603（0201） 0.3 （0.012） BKP1005（0402） 0.5 （0.020） BKP1608（0603） 0.8 （0.031） BKP2125（0805） 0.85（0.033） BKH0603（0201） 0.3 （0.012） BKH1005（0402） 0.5 （0.020） MCF0605（0202） 0.3 （0.012） MCFK1608（0603） 0.6 （0.024） MCFE1608（0603） 0.65（0.026） MCHK2012（0805） 0.8 （0.031） Chip cavity Ａ Ｂ 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 0.25±0.04 0.45±0.04 （0.010±0.002） （0.018±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.75±0.1 1.15±0.1 （0.030±0.004） （0.045±0.004） 0.25±0.04 0.45±0.04 （0.010±0.002） （0.018±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.2±0.1 2.17±0.1 （0.047±0.004） （0.085±0.004） 0.25±0.04 0.45±0.04 （0.010±0.002） （0.018±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 0.62±0.03 0.77±0.03 （0.024±0.001） （0.030±0.001） 1.1±0.05 1.9±0.05 （0.043±0.002） （0.075±0.002） 1.1±0.05 1.9±0.05 （0.043±0.002） （0.075±0.002） 1.55±0.2 2.3±0.2 （0.061±0.008） （0.091±0.008） Insertion Pitch Ｆ 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） Tape Thickness Ｔ 1.1max （0.043max） 1.1max （0.043max） 1.1max （0.043max） 1.1max （0.043max） 0.8max （0.031max） 1.1max （0.043max） 1.1max （0.043max） 0.45max （0.018max） 0.8max （0.031max） 1.1max （0.043max） 0.36max （0.014max） 0.45max （0.018max） 0.45max （0.018max） 0.45max （0.018max） 0.8max （0.031max） 0.36max （0.014max） 0.45max （0.018max） 0.8max （0.031max） 1.1max （0.043max） 1.1max （0.043max） 0.8max （0.031max） 0.36max （0.014max） 0.45max （0.018max） 0.8max （0.031max） 1.1max （0.043max） 1.1max （0.043max） 0.45max （0.018max） 0.8max （0.031max） 0.45max （0.018max） 0.72max (0.028max) 0.9max （0.035max） 0.9max （0.035max） Unit : mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E06R01 ●Embossed Tape (8mm wide) Unit：mm（inch） A B 8.0±0.3 (0.315±0.012) 3.5±0.05 (0.138±0.002) Sprocket hole F 1.75±0.1 (0.069±0.004） φ1.5＋0.1/－0 (φ0.059＋0.004/-0) 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) Type Thickness mm（inch） CK2125（0805） 1.25（0.049） CKS2125（0805） 1.25（0.049） CKP2012（0805） 0.9 （0.035） CKP2016（0806） 0.9 （0.035） Chip cavity Ａ Ｂ 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.55±0.2 2.3±0.2 （0.061±0.008） （0.091±0.008） 1.8±0.1 2.2±0.1 （0.071±0.004） （0.087±0.004） Insertion Pitch Ｆ 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.3±0.1 （0.091±0.004） 2.8±0.1 （0.110±0.004） 4.0±0.1 （0.157±0.004） 1.55±0.2 （0.061±0.008） 2.3±0.2 （0.091±0.008） 4.0±0.1 （0.157±0.004） 2.3±0.1 （0.091±0.004） 2.8±0.1 （0.110±0.004） 4.0±0.1 （0.157±0.004） 1.5±0.2 （0.059±0.008） 2.3±0.2 （0.091±0.008） 4.0±0.1 （0.157±0.004） 1.5±0.2 （0.059±0.008） 2.3±0.2 （0.091±0.008） 4.0±0.1 （0.157±0.004） 1.5±0.2 （0.059±0.008） 1.9±0.1 （0.075±0.004） 0.75±0.05 （0.030±0.002） 1.15±0.05 （0.045±0.002） 1.1±0.1 （0.043±0.004） 1.1±0.1 （0.043±0.004） 1.55±0.2 （0.061±0.008） 2.3±0.2 （0.091±0.008） 3.5±0.1 （0.138±0.004） 0.95±0.05 （0.037±0.002） 1.40±0.05 （0.055±0.002） 2.3±0.1 （0.091±0.004） 1.95±0.1 （±0.004） 2.3±0.2 （0.091±0.008） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 0.7 （0.028） CKP2520（1008） 0.9 （0.035） 1.1 （0.043） NM2012（0805） 0.9 （0.035） 0.9 （0.035） NM2520（1008） 1.1 （0.043） LK2125（0805） 1.25（0.049） 0.85（0.033） HK2125（0805） 1.0 （0.039） BK2125（0805） 1.25（0.049） BK3216（1206） 0.8（0.031） MCF0806（0302） 0.4 （0.016） MCF1210（0504） 0.55（0.022） MCF2010（0804） 0.45（0.018） MCKK1608(0603) 1.0 （0.039） MCKK2012（0805） 1.0 （0.039） Tape Thickness K T 2.0 0.3 （0.079） （0.012） 2.0 0.3 （0.079） （0.012） 1.3 0.3 （0.051） （0.012） 1.3 0.25 （0.051） （0.01） 1.4 （0.055） 1.4 0.3 （0.055） （0.012） 1.7 （0.067） 1.3 0.3 （0.051） （0.012） 1.4 （0.055） 0.3 （0.012） 1.7 （0.067） 2.0 0.3 （0.079） （0.012） 1.5 （0.059） 0.3 （0.012） 2.0 （0.079） 2.0 0.3 （0.079） （0.012） 1.4 0.3 （0.055） （0.012） 0.55 0.3 （0.022） （0.012） 0.65 0.3 （0.026） （0.012） 0.85 0.3 （0.033） （0.012） 1.4 0.25 （0.055） （0.01） 1.35 0.25 （0.053） （0.010） Unit : mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E06R01 ●Embossed Tape (4mm wide) Unit：mm（inch） 1.8±0.02 (0.071±0.001) A B 4.0±0.05 (0.157±0.002) 0.9±0.05 (0.035±0.002） φ0.8±0.04 (φ0.031±0.002) Sprocket hole 2.0±0.04 (0.079±0.002) 1.0±0.02 (0.039±0.001) F Chip cavity Thickness mm（inch） 0.2 （0.008） Type HKQ0402（01005） Ａ 0.23 Ｂ 0.43 Insertion Pitch Ｆ 1.0±0.02 Tape Thickness K T 0.5max. 0.25max. Unit : mm ④LEADER AND BLANK PORTION Blank portion Chip cavity Blank portion Leader 100mm or more (3.94inches or more) 160mm or more (6.3inches or more) Direction of tape feed 400mm or more (15.7inches or more) ⑤Reel Size t E C R B D A W A φ178±2.0 B φ50 or more C φ13.0±0.2 4mm width tape 8mm width tape t 1.5max. 2.5max. W 5±1.0 10±1.5 D φ21.0±0.8 E 2.0±0.5 R 1.0 (Unit : mm) ⑥Top tape strength The top tape requires a peel-off force of 0.1～0.7N in the direction of the arrow as illustrated below. Pull direction 0～15° Top tape Base tape ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E06R01 Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils（MC series F type） Metal Multilayer Chip Power Inductors (MCOILTM MC series) ■RELIABILITY DATA 1. Operating Temperature Range BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value －55～＋125℃ BK2010 BK3216 BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HKQ0402 HK0603 HK1005 HK1608 HK2125 HKQ0603W/HKQ0603S/HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 －55～＋85℃ －40～＋85℃ －40～＋85℃ －55～＋125℃ －40～＋85℃ －55～＋125℃ －40～＋125℃（Including self-generated heat） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 2. Storage Temperature Range BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value －55～＋125℃ BK2010 BK3216 BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HKQ0402 HK0603 HK1005 HK1608 HK2125 HKQ0603W/HKQ0603S/HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 －55～＋85℃ －40～＋85℃ －40～＋85℃ －55～＋125℃ －40～＋85℃ －55～＋125℃ －40～＋85℃ ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 3. Rated Current BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BK2010 BK3216 150～750mA DC 100～500mA DC 120～1000mA DC 115～450mA DC 200～300mA DC 150～1500mA DC 200～1200mA DC 100mA DC 100～200mA DC 0.55～1.1A DC 0.8～1.8A DC 0.8～2.4A DC 1.0～3.0A DC 1.5～4.0A DC 0.05A DC 0.1～0.13A DC 0.1～0.16A DC 0.1A DC 50～60mA DC 60～500mA DC 110～280mA DC 0.35～0.9A DC 0.7～1.7A DC 0.9～1.6A DC 1.1～1.8A DC 1.0～1.2A DC 0.9～1.2A DC 20～25mA DC 1～150mA DC 5～300mA DC 60～470mA DC 110～300mA DC (-55～+125℃） 200～900mA DC (-55～+85℃) 150～300mA DC 300mA DC 100～500mA DC 100～850mA DC 130～600mA DC 190～900mA DC 280～710mA DC Idc1 ： 1500～2300mA DC, Idc2 ： 900～2100mA DC Idc1 ： 1400～2600mA DC, Idc2 ： 800～1500mA DC Idc1 ： 2800～2000mA DC Idc2 ： 1300～2600mA DC Idc1 ： 2260～4320mA DC, Idc2 ： 1470～3600mA DC Idc1 ： 3600～6200mA DC, Idc2 ： 2100～4000mA DC BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 Specified Value CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 Definition of rated current： ・In the CK, CKS and BK Series, the rated current is the value of current at which the temperature of the element is increased within 20℃. ・In the BK Series P type, CK Series P type, NM Series, the rated current is the value of current at which the temperature of the element is increased within 40℃. ・In the LK, HK, HKQ0603, and AQ Series, the rated current is either the DC value at which the initial L value is decreased within 5% with the application of DC bias, or the value of current at which the temperature of the element is increased within 20℃. ・In the HKQ0402(～9N1), the rated current is either the DC value at which the initial L value is decreased within 5% with the application of DC bias, or the value of current at which the temperature of the element is increased within 20℃. ・In the HKQ0402(10N～), the rated current is either the DC value at which the initial L value is decreased within 5% with the application of DC bias, or the value of current at which the temperature of the element is increased within 25℃. ・In the MC Series, Idc1 is the DC value at which the initial L value is decreased within 30% and Idc2 is the DC value at which the temperature of element is increased within 40℃ by the application of DC bias. （at 20℃） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 4. Impedance BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BK2010 BK3216 10～330Ω ±5Ω(10Ω), ±25%(Other) 10～1200Ω ±25% 10～1800Ω ±25% 25～1500Ω ±25% 600～1800Ω ±25% 22～2500Ω ±25% 15～2500Ω ±25% 5～1000Ω ±25% 60～1000Ω ±25% 10～33Ω ±5Ω(10Ω)、±25%(Other) 10～120Ω ±5Ω(10Ω), ±25%(Other) 10～330Ω ±5Ω(EM100), ±25%(Other) 33～470Ω ±25% 33～330Ω ±25% 12～90Ω ±5Ω(12Ω), ±20%(35Ω,90Ω),±25%(60Ω) 12～90Ω ±5Ω(12Ω), ±20%(47Ω,90Ω),±25%(30Ω) 40～90Ω ±20%（2H900）,±25%（Other） 90Ω ±25% BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HKQ0402 HK0603 HK1005 HK1608 HK2125 HKQ0603W/HKQ0603S/HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 BK0402Series, BKP0402Series Measuring frequency : 100±1MHz Measuring equipment : E4991A（or its equivalent） Measuring jig : 16197A（or its equivalent） BK0603Series, BKP0603Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent） Measuring jig : 16193A（or its equivalent） BK1005Series, BKP1005Series ,BKH1005Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent） Measuring jig : 16192A（or its equivalent）, 16193A（or its equivalent） BK1608・2125Series, BKP1608・2125Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent）, 4195A（or its equivalent） Measuring jig : 16092A（or its equivalent） or 16192A（or its equivalent）/HW BK2010・3216Series, MCF Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent）, 4195A（or its equivalent） Measuring jig : 16192A（or its equivalent） － ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 5. Inductance BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BK2010 BK3216 BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 CK、LK、CKP、NM、MC Series Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig Test Methods and Remarks Measuring current － 4.7～10.0μH： ±20% 0.1～10.0μH： ±20% 1.0～10.0μH： ±20% 0.33～2.2μH： ±20% 0.47～4.7μH： ±20% 0.47～4.7μH： ±20% 0.47～4.7μH： ±20% 0.82～1.0μH： ±20% 1.0～2.2μH： ±20% 0.12～2.2μH： ±10 or 20% 0.047～33.0μH： ±20% 0.10～12.0μH： ±10% 0.047～33.0μH： ±20% 0.10～12.0μH： ±10% 1.0～6.2nH： ±0.3nH 6.8～100nH： ±5% 1.0～6.2nH： ±0.3nH 6.8～270nH： ±5% 1.0～5.6nH： ±0.3nH 6.8～470nH： ±5% 1.5～5.6nH： ±0.3nH 6.8～470nH： ±5% 0.5～3.9nH： ±0.1 or 0.2 or 0.3nH 4.3～5.6nH： ±0.3nH or 3% or 5% 6.2～47nH： ±3 or 5% 0.6～3.9nH： ±0.1 or 0.2 or 0.3nH 4.3～6.2nH： ±0.2 or 0.3nH or 3 or 5% 6.8～30nH： ±3 or 5% 33～100nH： ±5% 0.6～6.2nH： ±0.2 or 0.3nH 6.8～22nH： ±3 or 5% 0.6～4.2nH： ±0.1 or 0.2 or 0.3nH 4.3～6.5nH： ±0.2 or 0.3nH 6.8～22nH： ±3 or 5% 1.0～6.2nH： ±0.3nH 6.8～15nH： ±5% 0.24～1.0μH： ±20% 0.24～1.0μH： ±20% 0.24～1.0μH： ±20% 0.24～1.0μH： ±20% 0.24～1.0μH： ±20% : 2～4MHz（CK1608） : 2～25MHz（CK2125） : 2～10MHz（CKS2125） : 10～25MHz（LK1005） : 1～50MHz（LK1608） : 0.4～50MHz（LK2125） : 1MHz（CKP1608・CKP2012・CKP2016・CKP2520・NM2012・NM2520・MCFK1608・MCFE1608・MCHK2012・MCKK2012） :・4194A＋16085B＋16092A（or its equivalent） ・4195A＋41951＋16092A（or its equivalent） ・4294A＋16192A（or its equivalent） ・4291A＋16193A（or its equivalent）/LK1005 ・ 4285A ＋ 42841A ＋ 42842C ＋ 42851 － 61100 （ or its equivalent ） /CKP1608 ･ CKP2012 ・ CKP2016 ・ CKP2520 ・ NM2012 ・ NM2520・MCFK1608・MCFE1608・MCKK1608・MCHK2012・MCKK2012 :・1mA rms（0.047～4.7μH） ・0.1mA rms（5.6～33μH） HK、HKQ、AQ Series Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig : 100MHz（HK0603・HK1005・AQ105） : 50/100MHz（HK1608・HK2125） : 500MHz（HKQ0603S・HKQ0603U） : 300/500MHz（HKQ0603W） : 100/500MHz（HKQ0402） :・4291A＋16197A（or its equivalent）/HK0603・AQ105 ・4291A＋16193A（or its equivalent）/HK1005 ・E4991A＋16197A（or its equivalent）/HKQ0603S・HKQ0603U・HKQ0603W ・4291A＋16092A ＋ in-house made jig（or its equivalent）/HK1608・HK2125 ・E4991A＋16196D（or its equivalent）/HKQ0402 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 6. Q BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BK2010 BK3216 BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 LK Series Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig Measuring current Test Methods and Remarks HK、HKQ、AQ Series Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig － － 10～20 min. 10～35 min. 15～50 min. 4～5 min. 8 min. 8～12 min. 10～18 min. 3～8 min. 6～15 min. 10～13 min. 14 min. 8 min. － : 10～25MHz（LK1005） : 1～50MHz（LK1608） : 0.4～50MHz（LK2125） :・4194A＋16085B＋16092A（or its equivalent） ・4195A＋41951＋16092A（or its equivalent） ・4294A＋16192A（or its equivalent） ・4291A＋16193A（or its equivalent）/LK1005 ・1mA rms（0.047～4.7μH） ・0.1mA rms（5.6～33μH） : 100MHz（HK0603・HK1005・AQ105） : 50/100MHz（HK1608・HK2125） : 500MHz（HKQ0603S・HKQ0603U） : 300/500MHz（HKQ0603W） : 100/500MHz（HKQ0402） :・4291A＋16197A（or its equivalent）/HK0603・AQ105 ・4291A＋16193A（or its equivalent）/HK1005 ・E4991A＋16197A（or its equivalent）/HKQ0603S・HKQ0603U・HKQ0603W ・4291A＋16092A ＋ in-house made jig（or its equivalent）/HK1608, HK2125 ・E4991A＋16196D（or its equivalent）HKQ0402 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 7. DC Resistance BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 BK2010 BK3216 0.07～1.2Ωmax. 0.065～1.50Ω max. 0.03～0.90Ω max. 0.26～3.20Ω max. 0.85～2.00Ω max. 0.05～1.10Ω max. 0.05～0.75Ω max. 0.10～0.90Ω max. 0.15～0.80Ω max. 0.05～0.15Ω max. 0.030～0.180Ω max. 0.0273～0.220Ω max. 0.025～0.18Ω max. 0.020～0.075Ω max. 2.5～5.0Ω max 1.5～5.0Ω max. 1.5～4.5Ω max. 4.5Ω max. 0.45～0.85Ω（±30%） 0.16～0.65Ω max. 0.12～0.52Ω max. 0.15～0.35Ω max. 0.08～0.28Ω max. 0.075～0.20Ω max 0.05～0.16Ω max. 0.10～0.15Ω max. 0.11～0.22Ω max. 0.41～1.16Ω max. 0.2～2.2Ω max. 0.1～1.1Ω max. 0.11～3.74Ω max. 0.08～4.8Ω max. 0.05～2.6Ω max. 0.10～1.5Ω max. 0.08～5.0Ω max. 0.07～4.1Ω max. 0.06～1.29Ω max. 0.06～1.29Ω max. 0.07～0.45Ω max. 0.050～0.224Ω max. 0.100～0.340Ω max. 0.038～0.123Ω max. 0.024～0.111Ω max. 0.025～0.090Ω max. Measuring equipment：VOAC-7412, VOAC-7512, VOAC-7521（made by Iwasaki Tsushinki）, HIOKI3227 (or its equivalent) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 8. Self Resonance Frequency（SRF） BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BK2010 BK3216 BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 LK、CK Series : Measuring equipment Measuring jig HK、HKQ、AQ Series : Measuring equipment － 17～25MHz min. 24～235MHz min. 24～75MHz min. － 40～180MHz min. 9～260MHz min. 13～320MHz min. 900～10000MHz min. 400～10000MHz min. 300～10000MHz min. 200～4000MHz min. 1200～10000MHz min. 800～10000MHz min. 1900～10000MHz min. 1900～10000MHz min. 2300～10000MHz min. － : 4195A（or its equivalent） : 41951＋16092A（or its equivalent） : 8719C（or its equivalent）・8753D（or its equivalent）/HK2125 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 9. Temperature Characteristic BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BK2010 BK3216 BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W － HKQ0603S Test Methods and Remarks HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 HK、HKQ、AQ Series： Temperature range Reference temperature MC Series： Temperature range Reference temperature Inductance change：Within ±10％ : －30～＋85℃ : ＋20℃ : －40～＋85℃ : ＋20℃ ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 10. Resistance to Flexure of Substrate BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 Warp Testing board Thickness BK2010 BK3216 No mechanical damage. : 2mm（BK Series without 0402size、BKP、BKH1005、CK、CKS、CKP、LK、HK、HKQ0603S、HKQ0603U、 AQ Series、MCF1210、MC Series） : 1mm（BK0402、BKP0402、BKH0603、HKQ0402、HKQ0603W、MCF Series without 1210 size,） : glass epoxy-resin substrate : 0.8mm 20 Test Methods and Remarks R-230 Board Warp Deviation±1 45 45 （Unit：mm） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 11. Solderability BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 MCKK1608 MCHK2012 MCKK2012 Solder temperature Solder temperature Duration BK2010 BK3216 At least 90％ of terminal electrode is covered by new solder. ：230±5℃ (JIS Z 3282 H60A or H63A) ：245±3℃ (Sn/3.0Ag/0.5Cu) ：4±1 sec. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 12. Resistance to Soldering BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 BK2010 BK3216 Appearance：No significant abnormality Impedance change：Within ±30％ Appearance：No significant abnormality Impedance change：Within ±20％ Appearance：No significant abnormality Inductance change R10～4R7： Within ±10％ 6R8～100： Within ±15％ CKS2125 ： Within ±20％ CKP1608、CKP2012、CKP2016、CKP2520、NM2012、NM2520： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±15％ Appearance：No significant abnormality Inductance change 47N～4R7： Within ±10％ 5R6～330： Within ±15％ HK0603 HK1005 HK1608 HK2125 Appearance：No significant abnormality HKQ0402 Inductance change： Within ±5％ HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 Appearance：No significant abnormality MCKK1608 Inductance change： Within ±10％ MCHK2012 MCKK2012 Solder temperature ：260±5℃ Duration ：10±0.5 sec. Test Methods and Preheating temperature ：150 to 180℃ Remarks Preheating time ：3 min. Flux ：Immersion into methanol solution with colophony for 3 to 5 sec. Recovery ：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1） (Note 1) When there are questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 13. Thermal Shock BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 BK2010 BK3216 Appearance：No significant abnormality Impedance change： Within ±30％ Appearance：No significant abnormality Impedance change： Within ±20％ Appearance：No significant abnormality Inductance change：Within ±20％ Q change：Within ±30％ Appearance：No significant abnormality Inductance change：Within ±20％ CKP1608 CKP2012 CKP2016 Appearance：No significant abnormality Inductance change： Within ±30％ CKP2520 NM2012 NM2520 LK1005 Appearance：No significant abnormality LK1608 Inductance change： Within ±10％ Q change： Within ±30％ LK2125 HK0603 HK1005 HK1608 HK2125 Appearance：No significant abnormality HKQ0402 Inductance change： Within ±10％ Q change： Within ±20％ HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 Appearance：No significant abnormality MCKK1608 Inductance change： Within ±10％ MCHK2012 MCKK2012 Conditions for 1 cycle Step temperature（℃） time（min.） 1 Minimum operating temperature ＋0/－3 30±3 Test Methods and 2 Room temperature 2～3 Remarks 3 Maximum operating temperature ＋3/－0 30±3 4 Room temperature 2～3 Number of cycles：5 Recovery：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1） (Note 1) When there are questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition. Specified Value ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 14. Damp Heat（ Steady state） BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 Test Methods and Remarks BK2010 BK3216 Appearance：No significant abnormality Impedance change： Within ±30％ Appearance：No significant abnormality Impedance change： Within ±20％ Appearance：No significant abnormality Inductance change： Within ±20％ Q change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±20％ Appearance：No significant abnormality Inductance change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±10％ Q change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±20％ Q change： Within ±30％ HK0603 HK1005 HK1608 HK2125 Appearance：No significant abnormality HKQ0402 Inductance change： Within ±10％ Q change： Within ±20％ HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608 MCFE1608 Appearance：No significant abnormality MCKK1608 Inductance change： Within ±10％ MCHK2012 MCKK2012 BK、BKP、BKH、LK、CK、CKS、CKP、NM Series、MCF Series： Temperature ：40±2℃ Humidity ：90 to 95％RH Duration ：500 +24/-0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） HK、HKQ、AQ、MC Series： Temperature ：60±2℃ Humidity ：90 to 95％RH Duration ：500 +24/-0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） (Note 1) When there are questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 15. Loading under Damp Heat BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 CK1608 CK2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 Test Methods and Remarks BK2010 BK3216 Appearance：No significant abnormality Impedance change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±20％ Q change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±20％ Appearance：No significant abnormality Inductance change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±10％ Q change： Within ±30％ Appearance：No significant abnormality Inductance change： 0.047～12.0μH： Within ±10％ 15.0～33.0μH： Within ±15％ Q change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±20％ Q change： Within ±30％ HK0603 HK1005 HK1608 HK2125 Appearance：No significant abnormality HKQ0402 Inductance change： Within ±10％ Q change： Within ±20％ HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608※ MCFE1608※ Appearance：No significant abnormality MCKK1608※ Inductance change： Within ±10％ MCHK2012※ MCKK2012※ BK、BKP、BKH、LK、CK、CKS、CKP、NM Series： Temperature ：40±2℃ Humidity ：90 to 95％RH Applied current ：Rated current Duration ：500 +24/-0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） HK、HKQ、AQ、MC Series： Temperature ：60±2℃ Humidity ：90 to 95％RH Applied current ：Rated current ※MC series ; Idc2max Duration ：500 +24/-0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 16. Loading at High Temperature BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BKP0402 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603S HKQ0603U AQ105 MCFK1608※ MCFE1608※ MCKK1608※ MCHK2012※ MCKK2012※ Test Methods and Remarks Temperature Applied current Duration Recovery BK2010 BK3216 Appearance：No significant abnormality Impedance change： Within ±30％ Appearance：No significant abnormality Impedance change： Within ±20％ Appearance：No significant abnormality Inductance change： Within ±20％ Q change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±20％ Appearance：No significant abnormality Inductance change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±10％ Q change： Within ±30％ Appearance：No significant abnormality Inductance change： 0.047～12.0μH： Within ±10％ 15.0～33.0μH： Within ±15％ Q change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±20％ Q change： Within ±30％ Appearance：No significant abnormality Inductance change： Within ±10％ Q change： Within ±20％ Appearance：No significant abnormality Inductance change： Within ±10％ : Maximum operating temperature ：Rated current ※MC series ; Idc2max ：500 +24/-0 hrs ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber. （See Note 1） Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E06R01 Precautions on the use of Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils（MC series F type） Metal Multilayer Chip Power Inductors (MCOILTM MC series) ■PRECAUTIONS 1. Circuit Design Precautions ◆Verification of operating environment, electrical rating and performance 1. A malfunction in medical equipment, spacecraft, nuclear reactors, etc. may cause serious harm to human life or have severe social ramifications. As such, any inductors to be used in such equipment may require higher safety and/or reliability considerations and should be clearly differentiated from components used in general purpose applications. ◆Operating Current（Verification of Rated current） 1. The operating current including inrush current for inductors must always be lower than their rated values. 2. Do not apply current in excess of the rated value because the inductance may be reduced due to the magnetic saturation effect. 2. PCB Design Precautions ◆Pattern configurations（Design of Land-patterns） 1. When inductors are mounted on a PCB, the size of land patterns and the amount of solder used（size of fillet）can directly affect inductor performance. Therefore, the following items must be carefully considered in the design of solder land patterns: （1） The amount of solder applied can affect the ability of chips to withstand mechanical stresses which may lead to breaking or cracking. Therefore, when designing land-patterns it is necessary to consider the appropriate size and configuration of the solder pads which in turn determines the amount of solder necessary to form the fillets. （2） When more than one part is jointly soldered onto the same land or pad, the pad must be designed so that each component's soldering point is separated by solder-resist. （3） The larger size of land patterns and amount of solder, the smaller Q value after mounting on PCB. It makes higher the Q value to design land patterns smaller than terminal electrode of chips. ◆Pattern configurations（Inductor layout on panelized［ breakaway］ PC boards） 1. After inductors have been mounted on the boards, chips can be subjected to mechanical stresses in subsequent manufacturing processes （PCB cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering the reflow soldered boards etc.）For this reason, planning pattern configurations and the position of SMD inductors should be carefully performed to minimize stress. ◆Pattern configurations（Design of Land-patterns） 1. The following diagrams and tables show some examples of recommended patterns to prevent excessive solder amounts（larger fillets which extend above the component end terminations）. Examples of improper pattern designs are also shown. （1） Recommended land dimensions for a typical chip inductor land patterns for PCBs Land pattern Solder-resist Chip inductor Chip inductor W C B Technical considerations A B Recommended land dimensions for wave-soldering Type 1608 2012 2125 L 1.6 2.0 2.0 Size W 0.8 1.25 1.25 A 0.8～1.0 1.0～1.4 1.0～1.4 B 0.5～0.8 0.8～1.5 0.8～1.5 C 0.6～0.8 0.9～1.2 0.9～1.2 L （Unit：mm） 2016 2520 2.0 2.5 1.6 2.0 1.0～1.4 1.0～1.4 0.8～1.5 0.6～1.0 1.3～1.6 1.6～2.0 3216 3.2 1.6 1.8～2.5 0.8～1.7 1.2～1.6 Recommended land dimensions for reflow-soldering （Unit：mm） Type 0402 0603 1005 105 1608 L 0.4 0.6 1.0 1.0 1.6 Size W 0.2 0.3 0.5 0.6 0.8 A 0.15～0.25 0.20～0.30 0.45～0.55 0.50～0.55 0.8～1.0 B 0.10～0.20 0.20～0.30 0.40～0.50 0.30～0.40 0.6～0.8 C 0.15～0.30 0.25～0.40 0.45～0.55 0.60～0.70 0.6～0.8 2012 2.0 1.25 0.8～1.2 0.8～1.2 0.9～1.6 2125 2.0 1.25 0.8～1.2 0.8～1.2 0.9～1.6 2016 2.0 1.6 0.8～1.2 0.8～1.2 1.2～2.0 2520 2.5 2.0 1.0～1.4 0.6～1.0 1.8～2.2 3216 3.2 1.6 1.8～2.5 0.6～1.5 1.2～2.0 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E06R01 b b a a a a Excess solder can affect the ability of chips to withstand mechanical stresses. Therefore, please take proper precautions when designing land-patterns. Recommended land dimension for Reflow-soldering d c c Type 3216 2010 1210 0806 0605 L 3.2 2.0 1.25 0.85 0.65 Size W 1.6 1.0 1.0 0.65 0.50 a 0.7～0.9 0.5～0.6 0.45～0.55 0.25～0.35 0.27～0.33 b 0.8～1.0 c 0.4～0.5 d 0.8 （Unit：mm） d （（2） Examples of good and bad solder application Item 0.5～0.6 0.2～0.3 0.5 0.7～0.8 0.25～0.35 0.17～0.23 0.25～0.35 0.25～0.35 0.20～0.26 0.55 0.5 0.4 Not recommended Recommended Lead wire of component Solder-resist Mixed mounting of SMD and leaded components Chassis Solder (for grounding) Solder-resist Component placement close to the chassis Electrode pattern Lead wire of component Soldering iron Hand-soldering of leaded components near mounted components Solder-resist Solder-resist Horizontal component placement ◆Pattern configurations（Inductor layout on panelized［ breakaway］ PC boards） 1-1. The following are examples of good and bad inductor layout; SMD inductors should be located to minimize any possible mechanical stresses from board warp or deflection. Item Not recommended Recommended Position the component at a right angle to the direction of the mechanical stresses that are anticipated. Deflection of the board 1-2. To layout the inductors for the breakaway PC board, it should be noted that the amount of mechanical stresses given will vary depending on inductor layout. An example below should be counted for better design. E D Perforation C A B Slit Magnitude of stress A＞B＝C＞D＞E 1-3. When breaking PC boards along their perforations, the amount of mechanical stress on the inductors can vary according to the method used. The following methods are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, any ideal SMD inductor layout must also consider the PCB splitting procedure. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E06R01 3. Considerations for automatic placement Precautions ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the inductors when mounting onto the PC boards. 2. The maintenance and inspection of the mounter should be conducted periodically. ◆Selection of Adhesives 1. Mounting inductors with adhesives in preliminary assembly, before the soldering stage, may lead to degraded inductor characteristics unless the following factors are appropriately checked; the size of land patterns, type of adhesive, amount applied, hardening temperature and hardening period. Therefore, it is imperative to consult the manufacturer of the adhesives on proper usage and amounts of adhesive to use. ◆Adjustment of mounting machine 1. If the lower limit of the pick-up nozzle is low, too much force may be imposed on the inductors, causing damage. To avoid this, the following points should be considered before lowering the pick-up nozzle: （1） The lower limit of the pick-up nozzle should be adjusted to the surface level of the PC board after correcting for deflection of the board. （2） The pick-up pressure should be adjusted between 1 and 3N static loads. （3） To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins should be used under the PC board. The following diagrams show some typical examples of good pick-up nozzle placement: Item Improper method Proper method Single-sided mounting chipping or cracking supporting pins or back-up pins Double-sided mounting chipping or cracking Technical considerations supporting pins or back-up pins 2. As the alignment pin wears out, adjustment of the nozzle height can cause chipping or cracking of the inductors because of mechanical impact on the inductors. To avoid this, the monitoring of the width between the alignment pin in the stopped position, and maintenance, inspection and replacement of the pin should be conducted periodically. ◆Selection of Adhesives 1. Some adhesives may cause reduced insulation resistance. The difference between the shrinkage percentage of the adhesive and that of the inductors may result in stresses on the inductors and lead to cracking. Moreover, too little or too much adhesive applied to the board may adversely affect component placement, so the following precautions should be noted in the application of adhesives. （1） Required adhesive characteristics a. The adhesive should be strong enough to hold parts on the board during the mounting & solder process. b. The adhesive should have sufficient strength at high temperatures. c. The adhesive should have good coating and thickness consistency. d. The adhesive should be used during its prescribed shelf life. e. The adhesive should harden rapidly. f. The adhesive must not be contaminated. g. The adhesive should have excellent insulation characteristics. h. The adhesive should not be toxic and have no emission of toxic gasses. （2） When using adhesives to mount inductors on a PCB, inappropriate amounts of adhesive on the board may adversely affect component placement. Too little adhesive may cause the inductors to fall off the board during the solder process. Too much adhesive may cause defective soldering due excessive flow of adhesive on to the land or solder pad. Amount of adhesives After inductors are bonded ［Recommended conditions］ a a Figure 0805 case sizes as examples a 0.3mm min b b 100～120μm c Area with no adhesive c c 4. Soldering Precautions ◆Selection of Flux 1. Since flux may have a significant effect on the performance of inductors, it is necessary to verify the following conditions prior to use; （1） Flux used should be with less than or equal to 0.1 wt% （Chlorine conversion method） of halogenated content. Flux having a strong acidity content should not be applied. （2） When soldering inductors on the board, the amount of flux applied should be controlled at the optimum level. （3） When using water-soluble flux, special care should be taken to properly clean the boards. ◆Soldering 1. Temperature, time, amount of solder, etc. are specified in accordance with the following recommended conditions, and please contact us about peak temperature when you use lead-free paste. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E06R01 ◆Selection of Flux 1-1. When too much halogenated substance（Chlorine, etc.）content is used to activate the flux, or highly acidic flux is used, an excessive amount of residue after soldering may lead to corrosion of the terminal electrodes or degradation of insulation resistance on the surface of the Inductor. 1-2. Flux is used to increase solderability in flow soldering, but if too much is applied, a large amount of flux gas may be emitted and may detrimentally affect solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system. 1-3. Since the residue of water-soluble flux is easily dissolved by water content in the air, the residue on the surface of Inductor in high humidity conditions may cause a degradation of insulation resistance and therefore affect the reliability of the components. The cleaning methods and the capability of the machines used should also be considered carefully when selecting water-soluble flux. ◆Soldering 1-1. Preheating when soldering Heating: Chip inductor components should be preheated to within 100 to 130℃ of the soldering. Cooling: The temperature difference between the components and cleaning process should not be greater than 100℃. Chip inductors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. Therefore, the soldering process must be conducted with a great care so as to prevent malfunction of the components due to excessive thermal shock. ［Reflow soldering］ 【Recommended conditions for eutectic soldering】 【Recommended condition for Pb-free soldering】 300 300 Peak 260℃ Max. Within 10sec. 230℃ Within 10sec. 60sec. 60sec Min. 200 Min. Temperature（℃） Temperature（℃） Preheating Slow cooling 100 0 200 Slow cooling 100 0 Preheating150℃ Heating above 230℃ 60sec. Min. 40sec. Max. ※Ceramic chip components should be preheated to within 100 to 130℃ of the soldering. ※Assured to be reflow soldering for 2 times. ※ MC series; Peak 230 ℃ (eutectic soldering) 、 260 ℃ (Pb-free soldering)max within 5sec. Caution 1. The ideal condition is to have solder mass（fillet）controlled to 1/2 to 1/3 of the thickness of the inductor, as shown below: 1/2T～1/3T Inductor Technical considerations Solder T PC board 2. Because excessive dwell times can detrimentally affect solderability, soldering duration should be kept as close to recommended times as possible. ［Wave soldering］ 【Recommended conditions for eutectic soldering】 【Recommended condition for Pb-free soldering】 300 Preheating 120sec. Min. Peak 260℃ Max. Within 10sec. 230～250℃ Within 3sec. 200 Slow cooling 100 Temperature（℃） Temperature（℃） 300 0 200 120sec. Min. Preheating 150℃ 100 Slow cooling 0 ※Ceramic chip components should be preheated to within 100 to 130℃ of the soldering. ※Assured to be wave soldering for 1 time. ※Except for reflow soldering type. Caution 1. Make sure the inductors are preheated sufficiently. 2. The temperature difference between the inductor and melted solder should not be greater than 100 to 130℃. 3. Cooling after soldering should be as gradual as possible. 4. Wave soldering must not be applied to the inductors designated as for reflow soldering only. ［Hand soldering］ 【Recommended conditions for eutectic soldering 【Recommended condition for Pb-free soldering】 400 400 Peak 350℃ Max. Within 3sec. 230～280℃ Within 3sec. 300 200 Slow cooling 100 0 Preheating 60sec. Min. Temperature（℃） Temperature（℃） 300 ⊿T Slow cooling 200 100 0 Preheating 150℃ Min. 60sec. Min. （※⊿Ｔ≦190℃（ 3216Type max）, ⊿Ｔ≦130℃（ 3225 Type min） ※It is recommended to use 20W soldering iron and the tip is 1φor less. ※The soldering iron should not directly touch the components. ※Assured to be soldering iron for 1 time. Note: The above profiles are the maximum allowable soldering condition, therefore these profiles are not always recommended. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E06R01 Caution 1. Use a 20W soldering iron with a maximum tip diameter of 1.0 mm. 2. The soldering iron should not directly touch the inductor. 5. Cleaning Precautions ◆Cleaning conditions 1. When cleaning the PC board after the Inductors are all mounted, select the appropriate cleaning solution according to the type of flux used and purpose of the cleaning（e.g. to remove soldering flux or other materials from the production process.） 2. Cleaning conditions should be determined after verifying, through a test run, that the cleaning process does not affect the inductor's characteristics. Technical considerations ◆Cleaning conditions 1. The use of inappropriate solutions can cause foreign substances such as flux residue to adhere to the inductor, resulting in a degradation of the inductor's electrical properties（especially insulation resistance）. 2. Inappropriate cleaning conditions（insufficient or excessive cleaning）may detrimentally affect the performance of the inductors. （1） Excessive cleaning a. In the case of ultrasonic cleaning, too much power output can cause excessive vibration of the PC board which may lead to the cracking of the inductor or the soldered portion, or decrease the terminal electrodes' strength. Thus the following conditions should be carefully checked; Ultrasonic output Below 20W/ℓ Ultrasonic frequency Below 40kHz Ultrasonic washing period 5 min. or less 6. Post cleaning processes Precautions ◆Application of resin coatings, moldings, etc. to the PCB and components. 1. With some type of resins a decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while left under normal storage conditions resulting in the deterioration of the inductor's performance. 2. When a resin's hardening temperature is higher than the inductor's operating temperature, the stresses generated by the excess heat may lead to inductor damage or destruction. 3. Stress caused by a resin's temperature generated expansion and contraction may damage inductors. The use of such resins, molding materials etc. is not recommended. 7. Handling Precautions ◆Breakaway PC boards（splitting along perforations） 1. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆General handling precautions 1. Always wear static control bands to protect against ESD. 2. Keep the inductors away from all magnets and magnetic objects. 3. Use non-magnetic tweezers when handling inductors. 4. Any devices used with the inductors（ soldering irons, measuring instruments） should be properly grounded. 5. Keep bare hands and metal products（i.e., metal desk）away from chip electrodes or conductive areas that lead to chip electrodes. 6. Keep inductors away from items that generate magnetic fields such as speakers or coils. ◆Mechanical considerations 1. Be careful not to subject the inductors to excessive mechanical shocks. （1） If inductors are dropped on the floor or a hard surface they should not be used. （2） When handling the mounted boards, be careful that the mounted components do not come in contact with or bump against other boards or components. 8. Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control temperature and humidity in the storage area. Humidity should especially be kept as low as possible. ・Recommended conditions Ambient temperature: Below 30℃ Humidity: Below 70% RH The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of inductor is deteriorated as time passes, so inductors should be used within 6 months from the time of delivery. ・Inductor should be kept where no chlorine or sulfur exists in the air. Technical considerations ◆Storage 1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. For this reason, components should be used within 6 months from the time of delivery. If exceeding the above period, please check solderability before using the inductors. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E06R01