BRC2518T220K

for General Electronic Equipment 有关敝公司产品的注意事项 请务必在使用敝公司产品之前阅读。 注意 ■ 产品目录中的记载内容 4．责任的限制 本产品目录中所记载的内容为2021 月的内容。因产品改良等原因， 2019年1 10 月的内容。因产品改良等原因， 可能会不经预告而变更其记载内容，或是停止供应本产品目录中所记载 未经敝公司的事先书面同意，把本产品目录中所记载的产品使用于 的产品。所以，请务必在使用前先确认最新的产品信息。 禁止使用的设备，从而给客户或第三方造成损害的，敝公司不承担 非敝公司预设用途的设备、前述需要向敝公司咨询的设备或敝公司 任何责任，敬请知悉。 未按照本产品目录中所记载的内容或交货规格说明书使用敝公司产品， 即便其致使用设备发生损害、不良情况等时，敝公司也不承担任何责任， ■ 安全设计 需将敝公司的产品使用于对安全性和可靠性要求较高的设备、电路上时， 敬请知悉。 请进行充分的安全性评估和可靠性评估。另外，请通过设置保护电路、 ■ 签署交货规格说明书 就本产品目录中所记载产品的产品规格等相关内容，敝公司备有交货规 格说明书，详情请向敝公司咨询。在使用敝公司产品前请务必就交货规 格说明书之內容确认并批准之。 ■ 实装前的事前评估 使用敝公司产品时，请务必事先安装到使用设备之后，在实际使用的环 境下进行评估和确认。 ■ 用途的限定 1．可以使用的设备 本产品目录中所记载的产品预设为使用于一般电子设备［音像设备、 办公自动化设备、家电产品、办公设备、信息通讯设备（手机、电 脑等） ］以及面向本产品目录或是交货规格说明书中另行注明的设备 的通用性、标准性用途。 另外，面向汽车用电子设备、电信基础设施／工业设备、医疗设备 （国际（GHTF）第一类、第二类、第三类）方面的应用，敝公司也备 有预设的产品线，请参考本产品目录或是交货规格说明书的内容， 使用相对应的产品。 2．需要另行确认的设备 若考虑将本产品目录中所记载的产品使用于当产品发生故障、品质 不良，或是由此引起的运转失常而可能会危及生命、身体或是财产， 以及有可能给社会造成深刻影响的以下设备（不包括本产品目录或 是交货规格说明书中另行注明可以使用设备）等时，请务必事先向敝 公司咨询。 （１） 运输用设备（汽车驱动控制设备、火车控制设备、船舶控制设备等） （２） 交通信号设备 （３） 防灾／保安设备 （４） 医疗设备（国际（GHTF）第三类） 保护装置的系统，设置冗余电路不会被单一故障影响安全性的系统等失 效导向安全（fail-safe）设计，确保充分的安全性。 ■ 有关知识产权 本产品目录中所记载的信息是用于说明相关产品的典型操作以及相关应 用。此类信息的使用不代表对于敝公司以及第三方的知识产权以及其他 权利的使用许可或是不侵权保证。 ■ 保证范围 敝公司产品的保证范围仅限于已经交付的敝公司产品本身，由敝公司产 品的故障或不良情况所诱发的损害，敝公司不承担任何责任，敬请知悉。 但是，以书面形式另行签署了交易基本合同书、品质保证协定书等时， 敝公司将根据该合同的条件提供保证。 ■ 正规销售渠道 本产品目录中所记载的内容适用于从敝公司营业所、销售子公司、销售 代理店（即“正规销售渠道”）购买的敝公司产品，并不适用于从其他渠道 购买的敝公司产品，敬请知悉。 ■ 出口时的注意事项 本产品目录中所记载的部分产品在出口时须事先确认《外汇和对外贸易 法》以及美国在出口管理方面的相关法规，并办理相关手续。如有不明之 处，请向敝公司咨询。 （５）高公共性信息通讯设备／信息处理设备（电话交换机、电话／无 线／广播电视基站等） （６） 其他与上述设备有同等品质与可靠性要求的设备 3．禁止使用的设备 请勿将敝公司产品使用于对安全性和可靠性有着极高要求的以下设备。 （１） 航天设备（人工卫星、火箭等） （２） 航空设备（注释1） （３） 医疗设备 （国际 （GHTF） 第四类） 、植体（体内植入型） 医疗设备（注释2） （４） 发电控制设备（面向核能／水力／火力发电厂等的设备） （５） 海底设备（海底中继设备、海中的作业设备等） （６） 军事设备 （７） 其他与上述设备有同等品质与可靠性要求的设备 注释１ ：仅限于对航空设备的安全运行不产生直接干扰的设备［机内娱乐设备、机内 照明设备、电动座椅、餐饮设备等］ ，在满足敝公司另行指定的相关条件时， 亦可将敝公司产品用于以上用途。在贵公司考虑将敝公司的产品用于以上 用途时，请务必事先向敝公司咨询相关的信息。 注释２ ：包括注入人体内的部分和与此相连接的体外部分。 ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 2 20 21 for General Electronic Equipment SMD 功率电感器（NR 系列／ NR 系列 H 型／ S 型／ V 型） SMD 功率电感器（NR 系列／NR 系列 H 型／S 型／V 型） ■型号标示法 N R △ ① *使用温度范围：-25～+120℃（NRS40/50/60/80：-25～+125℃） （包含产品本身发热） 4 8 T △ ③ 1 0 0 ④ 类型 外装树脂规格 尺寸（L×W×H）［mm］ 2.0×2.0×1.0 2.0×2.0×1.2 2.4×2.4×1.0 2.4×2.4×1.2 3.0×3.0×1.0 3.0×3.0×1.2 3.0×3.0×1.5 4.0×4.0×1.0 4.0×4.0×1.2 4.0×4.0×1.8 4.9×4.9×1.0 4.9×4.9×1.2 4.9×4.9×1.4 4.9×4.9×2.0 4.9×4.9×2.4 4.9×4.9×3.0 4.9×4.9×4.0 6.0×6.0×1.0 6.0×6.0×1.2 6.0×6.0×1.4 6.0×6.0×2.0 6.0×6.0×2.8 6.0×6.0×4.5 8.0×8.0×3.0 8.0×8.0×4.0 M △ ⑤ ⑥ △＝空格 ③包装 代码 T△ 包装 卷盘带装 ④标称电感值 代码（例） 2R2 100 101 ※R＝小数点 标称电感值［μH］ 2.2 10 100 ⑤电感量公差 代码 M N 功率电感器 ②尺寸（L×W×H） 代码 2010 2012 2410 2412 3010 3012 3015 4010 4012 4018 5010 5012 5014 5020 5024 5030 5040 6010 6012 6014 6020 6028 6045 8030 8040 1 ② 电感器 ①类型 代码 NR△ NRH NRS NRV 0 电感量公差 ±20％ ±30％ ⑥本公司管理记号 i_smd_NR_j-E08R01-c.doc ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 51 for General Electronic Equipment ■标准外型尺寸／标准数量 推荐焊盘图案 L B H Type NRV2010 NRS2012, NRV2012 NRH2410 NRH2412 NR 3010, NRH3010 NR 3012, NRH3012, NRV3012 NR 3015, NRS3015 NR 4010, NRS4010 NR 4012, NRS4012 NR 4018, NRS4018 NRS8030 NR 8040, NRS8040 e C W f e A A 电感器 A B C 0.65 1.35 2.0 0.7 1.45 2.0 0.8 2.2 2.7 1.2 2.8 3.7 1.8 5.6 7.5 单位：mm 功率电感器 Type NRV2010 NRS2012 NRV2012 NRH2410 NRH2412 NR 3010 NRH3010 NR 3012 NRH3012 NRV3012 NR 3015 NRS3015 NR 4010 NRS4010 NR 4012 NRS4012 NR 4018 NRS4018 NRS8030 NR 8040 NRS8040 *1）0R9～6R8 型, L W H e f 2.0±0.1 （0.079±0.004） 2.0±0.1 （0.079±0.004） 2.4±0.1 （0.095±0.004） 2.4±0.1 （0.095±0.004） 3.0±0.1 （0.118±0.004） 2.0±0.1 （0.079±0.004） 2.0±0.1 （0.079±0.004） 2.4±0.1 （0.095±0.004） 2.4±0.1 （0.095±0.004） 3.0±0.1 （0.118±0.004） 1.0 max （0.039 max） 1.2 max （0.047 max） 1.0 max （0.039 max） 1.2 max （0.047 max） 1.0 max （0.039 max） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.6±0.2 （0.024±0.008） 0.6±0.2 （0.024±0.008） 0.9±0.2 （0.035±0.008） 1.25±0.2 （0.050±0.008） 1.25±0.2 （0.050±0.008） 1.45±0.2 （0.057±0.008） 1.45±0.2 （0.057±0.008） 1.9±0.2 （0.075±0.008） 3.0±0.1 （0.118±0.004） 3.0±0.1 （0.118±0.004） 1.2 max （0.047 max） 0.9±0.2 （0.035±0.008） 1.9±0.2 （0.075±0.008） 3.0±0.1 （0.118±0.004） 4.0±0.2 （0.158±0.008） 4.0±0.2 （0.158±0.008） 4.0±0.2 （0.158±0.008） 8.0±0.2 （0.315±0.008） 3.0±0.1 （0.118±0.004） 4.0±0.2 （0.158±0.008） 4.0±0.2 （0.158±0.008） 4.0±0.2 （0.158±0.008） 8.0±0.2 （0.315±0.008） 0.9±0.2 （0.035±0.008） 1.1±0.2 （0.043±0.008） 1.1±0.2 （0.043±0.008） 1.1±0.2 （0.043±0.008） 1.60±0.3 （0.063±0.012） 1.9±0.2 （0.075±0.008） 2.5±0.2 （0.098±0.008） 2.5±0.2 （0.098±0.008） 2.5±0.2 （0.098±0.008） 5.6±0.3 （0.22±0.012） 8.0±0.2 （0.315±0.008） 8.0±0.2 （0.315±0.008） 1.5 max （0.059 max） 1.0 max （0.039 max） 1.2 max （0.047 max） 1.8 max （0.071 max） 3.0 max （0.118 max） *1） 4.2 max （0.165 max） *2） 4.0 max （0.158 max） 1.60±0.3 （0.063±0.012） 5.6±0.3 （0.22±0.012） *2）100～221 型 标准数量［pcs］ 卷盘带装 2500 2500 2500 2500 2000 2000 2000 5000 4500 3500 1000 1000 单位：mm（inch） i_smd_NR_j-E08R01-c.doc ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 52 21 for General Electronic Equipment L 推荐焊盘图案 ∆I H B e C W f e A A A B C 1.5 3.6 4.0 1.6 4.7 5.7 电感器 Type NRS5010 NRS5012 NRS5014 NRS5020 NRS5024 NRS5030 NR 5040, NRS5040 NRS6010 NR 6012, NRS6012 NRS6014 NR 6020, NRS6020 NR 6028, NRS6028 NR 6045, NRS6045 单位：mm L W 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） NRS5024 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） NRS5030 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） NR 5040 NRS5040 4.9±0.2 （0.193±0.008） 4.9±0.2 （0.193±0.008） NRS5010 NRS5012 NRS5014 NRS5020 6.0±0.2 6.0±0.2 （0.236±0.008） （0.236±0.008） NR 6012 6.0±0.2 6.0±0.2 NRS6012 （0.236±0.008） （0.236±0.008） 6.0±0.2 6.0±0.2 NRS6014 （0.236±0.008） （0.236±0.008） NR 6020 6.0±0.2 6.0±0.2 NRS6020 （0.236±0.008） （0.236±0.008） NR 6028 6.0±0.2 6.0±0.2 NRS6028 （0.236±0.008） （0.236±0.008） NR 6045 6.0±0.2 6.0±0.2 NRS6045 （0.236±0.008） （0.236±0.008） *3）1R0～1R5 型, *4）2R2～330 型 *5）R47～100 型, *6）150～470 型 *7）1R5～100 型, *8）150～470 型 NRS6010 H 1.0 max （0.039 max） 1.2 max （0.047 max） 1.4 max （0.055 max） 2.0 max （0.079 max） *3） 2.5 max （0.098 max） *4） 2.4 max （0.095 max） *5） 3.1 max （0.122 max） *6） 3.0 max （0.118 max） *7） 4.1 max （0.161 max） *8） 4.0 max （0.158 max） 1.0 max （0.039 max） 1.2 max （0.047 max） 1.4 max （0.055 max） 2.0 max （0.079 max） 2.8 max （0.110 max） 4.5 max （0.177 max） 标准数量［pcs］ 卷盘带装 e f ΔI 1.2±0.2 （0.047±0.008） 1.2±0.2 （0.047±0.008） 1.2±0.2 （0.047±0.008） 1.2±0.2 （0.047±0.008） 3.3±0.2 （0.130±0.008） 3.3±0.2 （0.130±0.008） 3.3±0.2 （0.130±0.008） 3.3±0.2 （0.130±0.008） 1.3typ （0.051typ） 1.3typ （0.051typ） 1.3typ （0.051typ） 1.3typ （0.051typ） 1.2±0.2 （0.047±0.008） 3.3±0.2 （0.130±0.008） 1.3typ （0.051typ） 2500 1.2±0.2 （0.047±0.008） 3.3±0.2 （0.130±0.008） 1.3typ （0.051typ） 500 1.2±0.2 （0.047±0.008） 3.3±0.2 （0.130±0.008） 1.3typ （0.051typ） 1500 1.35±0.2 （0.053±0.008） 1.35±0.2 （0.053±0.008） 1.35±0.2 （0.053±0.008） 1.35±0.2 （0.053±0.008） 1.35±0.2 （0.053±0.008） 1.35±0.2 （0.053±0.008） 4.0±0.2 （0.158±0.008） 4.0±0.2 （0.158±0.008） 4.0±0.2 （0.158±0.008） 4.0±0.2 （0.158±0.008） 4.0±0.2 （0.158±0.008） 4.0±0.2 （0.158±0.008） 2.3typ （0.091typ） 2.3typ （0.091typ） 2.3typ （0.091typ） 2.3typ （0.091typ） 2.3typ （0.091typ） 2.3typ （0.091typ） 功率电感器 Type 1000 1000 1000 800 1000 1000 1000 2500 2000 1500 单位：mm（inch） i_smd_NR_j-E08R01-c.doc ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 53 for General Electronic Equipment ■型号一览 ●NRS2012屏蔽型 型号 NRS2012T NRS2012T NRS2012T NRS2012T NRS2012T 1R0N GJ 1R5N GJ 2R2M GJ 3R3M GJ 4R7M GJ EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 ±30％ ±30％ ±20％ ±20％ ±20％ － － － － － EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.47 0.68 1.0 1.5 2.2 3.3 4.7 ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ － － － － － － － EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 ±30％ ±30％ ±20％ ±20％ ±20％ － － － － － EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 120 106 94 77 56 50 43 32 27 22 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.47 1.0 1.5 2.2 3.3 4.7 6.8 10 ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ 180 101 89 72 56 45 34 29 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.2 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 120 99 86 64 50 44 34 25 22 20 17 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.070 1,900 2,050 1,700 1,850 0.090 1,650 1,800 1,500 1,650 0.107 1,350 1,500 1,370 1,500 0.190 1,000 1,150 1,020 1,100 0.241 900 1,050 910 1,000 测试频率［kHz］ 100 100 100 100 100 ●NRV2010型 型号 电感器 NRV2010T NRV2010T NRV2010T NRV2010T NRV2010T NRV2010T NRV2010T R47N GF R68N GF 1R0N GF 1R5M GF 2R2M GF 3R3M GF 4R7M GF 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.052 2,100 2,250 2,000 2,300 0.060 1,850 2,000 1,850 2,100 0.080 1,550 1,700 1,600 1,850 0.100 1,350 1,450 1,450 1,650 0.175 1,100 1,200 1,100 1,200 0.250 880 950 1,000 1,100 0.320 760 810 820 930 测试频率［kHz］ 100 100 100 100 100 100 100 功率电感器 ●NRV2012型 型号 NRV2012T NRV2012T NRV2012T NRV2012T NRV2012T 1R0N GF 1R5N GF 2R2M GF 3R3M GF 4R7M GF 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.073 2,200 2,350 1,650 1,830 0.100 1,800 1,950 1,400 1,550 0.129 1,600 1,700 1,200 1,350 0.227 1,250 1,350 900 1,040 0.325 1,100 1,150 750 850 测试频率［kHz］ 100 100 100 100 100 ●NRH2410屏蔽型 型号 NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T R68NN 4 1R0NN 4 1R5MN 2R2MN 3R3MN 4R7MN 6R8MN 100MN 150MN 220MN 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.060 2,200 2,300 1,570 1,810 0.070 1,800 1,950 1,410 1,640 0.110 1,550 1,640 1,160 1,320 0.150 1,290 1,340 970 1,110 0.220 1,000 1,140 770 890 0.290 880 930 670 780 0.410 750 765 570 650 0.690 550 605 450 520 1.02 470 520 370 430 1.47 390 405 300 340 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 ●NRH2412屏蔽型 型号 NRH2412T NRH2412T NRH2412T NRH2412T NRH2412T NRH2412T NRH2412T NRH2412T R47NNGJ 1R0NNGH 1R5NNGH 2R2MNGH 3R3MNGH 4R7MNGH 6R8MNGH 100MNGH 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.050 2,900 3,690 2,100 2,300 0.077 2,350 2,610 1,300 1,540 0.100 2,100 2,290 1,150 1,390 0.140 1,700 1,940 1,000 1,190 0.225 1,400 1,600 750 890 0.300 1,150 1,280 650 770 0.420 950 1,100 550 635 0.600 810 900 450 510 测试频率［kHz］ 100 100 100 100 100 100 100 100 ●NRH3010屏蔽型 型号 NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T 1R2NN 1R5NN 2R2MN 3R3MN 4R7MN 6R8MN 100MN 150MN 220MN 330MN 470MN 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.065 1,700 1,740 1,480 1,850 0.075 1,440 1,500 1,370 1,680 0.083 1,300 1,400 1,300 1,550 0.130 1,000 1,020 1,030 1,220 0.170 850 930 900 1,090 0.250 700 750 745 920 0.350 600 650 620 780 0.550 450 520 480 600 0.770 380 440 410 510 1.250 290 360 350 440 2.050 250 300 285 320 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 54 21 for General Electronic Equipment ■型号一览 ●NRH3012屏蔽型 型号 R47NN 1R0NN 1R5NN 2R2MN 3R3MN 4R7MN 6R8MN 100MN 150MN 220MN 330MN 470MN 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.47 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 160 111 95 78 61 50 43 32 26 22 18 16 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ 110 92 70 55 48 40 32 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 100 87 64 49 40 36 28 23 20 18 17 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 116 73 58 47 38 31 24 19 15 13 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 100 90 70 60 45 35 30 24 18 15 12 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.033 2,600 3,200 1,900 2,280 0.048 2,200 2,500 1,710 1,970 0.055 1,700 1,900 1,600 1,750 0.075 1,500 1,750 1,370 1,600 0.100 1,200 1,500 1,210 1,480 0.130 1,000 1,200 1,060 1,280 0.190 850 910 890 1,000 0.270 730 780 720 850 0.450 530 650 570 680 0.630 500 550 500 590 0.960 360 430 450 510 1.340 280 380 380 430 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 电感器 NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T EHS ●NRV3012屏蔽型 型号 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 测试频率［kHz］ 功率电感器 NRV3012T NRV3012T NRV3012T NRV3012T NRV3012T NRV3012T NRV3012T 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.065 2,500 3,000 1,600 1,970 0.075 2,100 2,500 1,400 1,610 0.120 1,800 2,100 1,100 1,330 0.150 1,600 1,900 1,000 1,260 0.190 1,250 1,500 850 1,040 0.300 950 1,200 650 800 0.470 800 990 550 640 100 100 100 100 100 100 100 ●NRS3015屏蔽型 型号 NRS3015T NRS3015T NRS3015T NRS3015T NRS3015T NRS3015T NRS3015T NRS3015T NRS3015T NRS3015T NRS3015T 1R0NNGH 1R5NNGH 2R2MNGH 3R3MNGH 4R7MNGH 6R8MNGH 100MNGH 150MNGH 220MNGH 330MNGH 470MNGH 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.030 2,100 2,400 2,100 2,350 0.038 1,800 2,100 1,820 2,100 0.058 1,480 1,700 1,500 1,800 0.078 1,210 1,400 1,230 1,500 0.120 1,020 1,100 1,040 1,300 0.160 870 920 880 1,100 0.220 700 750 710 840 0.325 580 680 680 760 0.520 470 540 470 530 0.780 400 440 440 490 1.100 325 380 350 380 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 ●NRS4010屏蔽型 型号 NRS4010T NRS4010T NRS4010T NRS4010T NRS4010T NRS4010T NRS4010T NRS4010T NRS4010T NRS4010T 1R0NDGG 2R2MDGG 3R3MDGG 4R7MDGG 6R8MDGG 100MDGG 150MDGG 220MDGG 330MDGG 470MDGG 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.056 2,000 2,280 1,900 2,390 0.085 1,200 1,610 1,500 1,800 0.100 1,100 1,300 1,400 1,700 0.140 950 1,100 1,200 1,450 0.200 800 890 1,000 1,200 0.300 620 760 750 860 0.430 540 635 600 700 0.570 450 540 500 600 0.900 350 440 400 460 1.250 300 350 350 370 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 ●NRS4012屏蔽型 型号 NRS4012T NRS4012T NRS4012T NRS4012T NRS4012T NRS4012T NRS4012T NRS4012T NRS4012T NRS4012T NRS4012T 1R0NDGG 1R5NDGG 2R2MDGJ 3R3MDGJ 4R7MDGJ 6R8MDGJ 100MDGJ 150MDGJ 220MDGJ 330MDGJ 470MDGJ 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.042 2,800 2,900 2,200 2,670 0.051 2,300 2,500 2,000 2,430 0.060 1,650 1,950 1,900 2,100 0.070 1,400 1,700 1,700 1,880 0.095 1,200 1,320 1,500 1,570 0.125 900 1,170 1,300 1,400 0.170 800 990 1,100 1,200 0.260 650 820 750 840 0.400 500 620 620 650 0.600 400 500 480 530 0.770 350 430 420 470 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 55 for General Electronic Equipment ■型号一览 ●NRS4018屏蔽型 型号 电感器 NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T NRS4018T 1R0NDGJ 1R5NDGJ 2R2MDGJ 3R3MDGJ 4R7MDGJ 6R8MDGJ 100MDGJ 150MDGJ 220MDGJ 330MDGJ 470MDGJ 680MDGJ 101MDGJ 151MDGJ 221MDGJ EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 90 75 60 45 35 30 25 18 15 12 10 8.3 6.5 5.5 4.0 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 2.2 3.3 4.7 6.8 10 15 22 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 95 65 42 37 33 23 19 15 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 100 86 70 48 40 36 26 22 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.47 1.2 2.2 3.3 4.7 6.8 10 15 22 ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ 185 86 56 48 41 33 27 20 16 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.47 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 47 100 ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 230 81 68 57 46 37 30 24 20 17 12 7 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.027 4,000 4,590 3,200 3,720 0.037 3,300 3,750 2,400 3,000 0.042 3,000 3,110 2,200 2,590 0.055 2,300 2,560 2,000 2,240 0.070 2,000 2,330 1,700 1,880 0.098 1,600 1,820 1,450 1,690 0.150 1,300 1,440 1,200 1,250 0.210 1,100 1,150 850 915 0.290 900 920 720 810 0.460 700 830 550 630 0.650 600 700 440 520 1.00 520 600 320 400 1.45 420 490 280 330 2.30 340 390 220 280 3.80 275 310 170 210 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 ●NRS5010型 功率电感器 型号 NRS5010T NRS5010T NRS5010T NRS5010T NRS5010T NRS5010T NRS5010T NRS5010T 1R0NMGF 2R2NMGF 3R3MMGF 4R7MMGF 6R8MMGF 100MMGF 150MMGF 220MMGF 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.070 2,350 2,510 1,750 2,000 0.105 1,500 1,710 1,400 1,600 0.125 1,400 1,530 1,250 1,520 0.145 1,200 1,340 1,150 1,390 0.185 1,000 1,120 1,000 1,210 0.250 850 970 900 950 0.400 680 740 650 700 0.600 550 620 450 560 测试频率［kHz］ 100 100 100 100 100 100 100 100 ●NRS5012型 型号 NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T 1R0NMGF 1R5NMGF 2R2MMGF 3R3MMGF 4R7MMGF 6R8MMGF 100MMGF 150MMGF 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.053 4,500 4,670 2,300 2,750 0.070 3,800 3,970 2,200 2,470 0.085 3,100 3,510 2,000 2,300 0.160 2,400 2,580 1,450 1,650 0.180 2,200 2,320 1,400 1,560 0.260 1,700 1,950 1,100 1,260 0.420 1,400 1,550 850 1,000 0.670 1,200 1,240 640 740 测试频率［kHz］ 100 100 100 100 100 100 100 100 ●NRS5014屏蔽型 型号 NRS5014T NRS5014T NRS5014T NRS5014T NRS5014T NRS5014T NRS5014T NRS5014T NRS5014T R47NMGG 1R2NMGG 2R2NMGG 3R3NMGG 4R7NMGG 6R8MMGG 100MMGG 150MMGG 220MMGG 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.025 5,800 6,400 3,300 3,470 0.045 3,800 4,200 2,400 3,000 0.065 2,800 3,100 2,000 2,400 0.080 2,350 2,650 1,700 2,200 0.100 2,050 2,400 1,400 1,900 0.150 1,600 1,850 1,200 1,450 0.200 1,400 1,600 1,050 1,250 0.320 1,100 1,300 650 790 0.450 900 1,000 550 660 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 ●NRS5020屏蔽型 型号 NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T R47NMGJ 1R0NMGJ 1R5NMGJ 2R2NMGJ 3R3NMGJ 4R7MMGJ 6R8MMGJ 100MMGJ 150MMGJ 220MMGJ 470MMGJ 101MMGJ 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.012 6,100 6,900 5,000 5,800 0.021 4,000 4,500 3,600 3,710 0.026 3,350 3,800 3,200 3,540 0.035 2,900 3,200 2,900 3,200 0.048 2,400 2,700 2,400 3,080 0.060 2,000 2,270 2,000 2,370 0.090 1,600 1,850 1,650 2,200 0.120 1,300 1,480 1,450 1,850 0.165 1,100 1,260 1,200 1,480 0.260 900 1,100 1,000 1,230 0.435 630 750 560 610 0.850 420 510 400 450 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 56 21 for General Electronic Equipment ■型号一览 ●NRS5024屏蔽型 型号 NRS5024T NRS5024T NRS5024T NRS5024T NRS5024T NRS5024T NRS5024T NRS5024T NRS5024T NRS5024T 1R0NMGJ 1R5NMGJ 2R2NMGJ 3R3NMGJ 4R7MMGJ 6R8MMGJ 100MMGJ 150MMGJ 220MMGJ 330MMGJ 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 85 67 51 41 37 28 21 18 15 11 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.47 1.0 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 185 110 46 36 31 22 20 14 13 10 9 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 60 42 32 28 21 18 13 9 7 6 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.5 2.2 3.3 4.7 6.8 10 22 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 77 56 42 36 30 25 12 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.5 3.3 4.7 5.3 6.8 10 15 22 33 47 68 100 ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 95 69 45 42 36 34 30 22 18 12 8 6 3 1 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.016 5,800 6,800 4,400 4,900 0.022 5,200 5,800 3,600 4,300 0.029 4,100 4,800 3,100 3,600 0.043 3,100 3,700 2,400 2,750 0.055 2,700 3,400 2,000 2,400 0.080 2,200 2,750 1,600 1,800 0.125 1,700 2,100 1,200 1,460 0.170 1,400 1,750 1,000 1,250 0.230 1,200 1,450 820 900 0.370 1,000 1,200 630 700 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 电感器 EHS ●NRS5030屏蔽型 型号 R47NMGJ 1R0NMGJ 2R2NMGJ 3R3MMGJ 4R7MMGJ 6R8MMGJ 100MMGJ 150MMGJ 220MMGJ 330MMGJ 470MMGJ 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 功率电感器 NRS5030T NRS5030T NRS5030T NRS5030T NRS5030T NRS5030T NRS5030T NRS5030T NRS5030T NRS5030T NRS5030T 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Typ. Max. Typ. 0.010 9,000 9,400 5,000 5,900 0.015 6,600 7,400 4,000 4,900 0.023 4,200 5,000 3,500 4,100 0.030 3,600 3,900 3,000 3,600 0.035 3,100 3,500 2,600 3,000 0.052 2,500 2,800 2,300 2,500 0.070 2,100 2,300 1,700 2,000 0.125 1,600 1,800 1,400 1,550 0.180 1,400 1,500 1,050 1,200 0.225 1,150 1,250 800 950 0.325 950 1,050 700 800 ●NRS5040屏蔽型 型号 NRS5040T 1R5NMGJ NRS5040T 2R2NMGJ NRS5040T 3R3NMGJ NRS5040T 4R7NMGK NRS5040T 6R8MMGJ NRS5040T 100MMGJ NRS5040T 150MMGJ NRS5040T 220MMGK NRS5040T 330MMGJ NRS5040T 470MMGJ 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Typ. Max. Typ. 0.017 6,400 6,530 4,500 4,730 0.022 5,000 5,250 3,700 4,080 0.027 4,000 4,280 3,300 3,770 0.029 3,300 3,470 3,100 3,500 0.049 2,800 2,910 2,400 2,470 0.056 2,300 2,470 2,100 2,210 0.080 2,000 2,150 1,800 1,920 0.126 1,500 1,580 1,400 1,470 0.180 1,300 1,390 1,200 1,270 0.310 1,100 1,150 900 950 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 ●NRS6010型 型号 NRS6010T NRS6010T NRS6010T NRS6010T NRS6010T NRS6010T NRS6010T 1R5MMGF 2R2MMGF 3R3MMGF 4R7MMGF 6R8MMGF 100MMGF 220MMGF 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.090 2,400 2,650 1,900 2,150 0.110 1,900 2,120 1,700 1,950 0.135 1,600 1,750 1,500 1,750 0.165 1,300 1,470 1,400 1,600 0.220 1,200 1,300 1,200 1,320 0.270 1,000 1,100 1,100 1,200 0.580 650 720 700 740 测试频率［kHz］ 100 100 100 100 100 100 100 ●NRS6012屏蔽型 型号 NRS6012T 1R0NMGJ NRS6012T 1R5NMGG NRS6012T 2R5NMGG NRS6012T 3R3NMGG NRS6012T 4R7MMGG NRS6012T 5R3MMGJ NRS6012T 6R8MMGJ NRS6012T 100MMGJ NRS6012T 150MMGJ NRS6012T 220MMGJ NRS6012T 330MMGJ NRS6012T 470MMGJ NRS6012T 680MMGJ NRS6012T 101MMGJ 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.050 3,000 3,900 2,400 2,700 0.067 2,600 3,500 2,100 2,300 0.090 2,100 2,900 1,800 2,100 0.105 1,800 2,500 1,700 1,950 0.125 1,600 2,100 1,550 1,750 0.125 1,500 1,750 1,550 1,750 0.165 1,300 1,600 1,350 1,600 0.200 1,000 1,400 1,200 1,380 0.295 800 1,100 800 950 0.465 760 900 650 750 0.580 590 800 550 670 0.965 520 630 460 540 1.16 440 560 410 450 1.67 350 490 320 380 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 57 for General Electronic Equipment ■型号一览 ●NRS6014屏蔽型 型号 NRS6014T NRS6014T NRS6014T NRS6014T NRS6014T NRS6014T NRS6014T NRS6014T 1R2NMGG 2R2NMGG 3R3NMGG 4R7MMGG 6R8MMGG 100MMGG 150MMGG 220MMGG EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.2 2.2 3.3 4.7 6.8 10 15 22 ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ 77 61 41 36 30 24 20 16 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.8 1.5 2.2 3.3 4.7 6.8 10 22 ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ 110 93 73 55 43 30 18 11 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.9 1.5 2.2 3.0 4.7 6.8 10 15 22 33 47 68 100 ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 90 78 68 55 39 25 20 17 12 10 8 5 3 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.3 1.5 1.8 2.2 2.3 3.0 3.3 4.5 4.7 6.3 6.8 10 15 22 33 47 68 100 ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 110 95 95 80 60 60 45 45 25 25 15 15 12 10 7 6 5 4 3 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.042 4,000 4,400 2,750 3,200 0.055 3,000 3,500 2,300 2,600 0.075 2,500 2,600 2,000 2,200 0.090 2,000 2,170 1,900 1,950 0.115 1,700 1,880 1,650 1,700 0.140 1,400 1,540 1,400 1,500 0.210 1,150 1,300 1,200 1,280 0.300 950 1,100 1,000 1,090 测试频率［kHz］ 100 100 100 100 100 100 100 100 ●NRS6020屏蔽型 电感器 型号 功率电感器 NRS6020T NRS6020T NRS6020T NRS6020T NRS6020T NRS6020T NRS6020T NRS6020T 0R8NMGG 1R5NMGJ 2R2NMGJ 3R3NMGJ 4R7NMGJ 6R8NMGJ 100MMGG 220MMGG 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Typ. Max. Typ. 0.020 6,400 7,400 4,100 4,800 0.026 4,300 5,300 3,600 4,200 0.034 3,200 4,000 2,900 3,400 0.040 2,800 3,400 2,750 3,100 0.058 2,400 2,800 2,150 2,500 0.085 2,000 2,600 1,800 2,100 0.125 1,900 2,240 1,500 1,700 0.290 1,250 1,470 950 1,100 测试频率［kHz］ 100 100 100 100 100 100 100 100 ●NRS6028屏蔽型 型号 NRS6028T 0R9NMGJ NRS6028T 1R5NMGJ NRS6028T 2R2NMGJ NRS6028T 3R0NMGJ NRS6028T 4R7MMGK NRS6028T 6R8MMGJ NRS6028T 100MMGK NRS6028T 150MMGJ NRS6028T 220MMGJ NRS6028T 330MMGJ NRS6028T 470MMGJ NRS6028T 680MMGJ NRS6028T 101MMGJ 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Typ. Max. Typ. 0.013 6,700 7,900 4,600 5,200 0.016 5,100 6,100 4,200 4,700 0.020 4,200 5,100 3,700 4,200 0.023 3,600 4,300 3,400 3,900 0.031 2,700 3,300 3,000 3,400 0.043 2,600 3,000 2,500 2,900 0.065 1,900 2,200 1,900 2,200 0.095 1,600 1,900 1,800 1,900 0.135 1,300 1,600 1,400 1,600 0.220 1,100 1,300 1,100 1,250 0.300 1,000 1,150 920 1,050 0.420 800 950 770 880 0.600 650 750 660 750 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 ●NRS6045屏蔽型 型号 NRS6045T 1R0NMGK NRS6045T 1R3NMGK NRS6045T 1R5NMGK NRS6045T 1R8NMGK NRS6045T 2R2NMGK NRS6045T 2R3NMGK NRS6045T 3R0NMGK NRS6045T 3R3NMGK NRS6045T 4R5MMGK NRS6045T 4R7NMGK NRS6045T 6R3MMGK NRS6045T 6R8MMGK NRS6045T 100MMGK NRS6045T 150MMGK NRS6045T 220MMGK NRS6045T 330MMGK NRS6045T 470MMGK NRS6045T 680MMGK NRS6045T 101MMGK 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Typ. Max. Typ. 0.014 9,800 11,000 4,500 5,200 0.016 8,200 9,300 4,200 4,800 0.016 8,200 9,300 4,200 4,800 0.019 7,200 8,100 3,900 4,400 0.022 6,400 7,300 3,600 4,100 0.022 6,400 7,300 3,600 4,100 0.024 5,600 6,500 3,300 4,000 0.024 5,600 6,500 3,300 4,000 0.030 4,400 5,400 3,100 3,600 0.030 4,400 5,400 3,100 3,600 0.036 3,600 4,300 3,000 3,300 0.036 3,600 4,300 3,000 3,300 0.046 3,100 3,600 2,400 2,800 0.070 2,500 3,000 1,900 2,300 0.107 2,000 2,400 1,600 1,900 0.141 1,650 2,000 1,400 1,600 0.211 1,400 1,600 1,150 1,350 0.304 1,100 1,300 950 1,100 0.466 900 1,200 750 900 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 58 21 for General Electronic Equipment ■型号一览 ●NRS8030屏蔽型 型号 1R0NJGJ 1R5NJGJ 2R2NJGJ 3R3MJGJ 4R7MJGJ 6R8MJGJ 100MJGJ 150MJGJ 220MJGJ 330MJGJ 470MJGJ 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 120 80 60 50 40 32 27 20 16 13 11 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.9 1.0 1.4 1.5 2.0 2.2 3.3 3.6 4.7 6.8 10 15 22 33 47 68 100 150 220 ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 85 85 63 63 50 50 34 34 30 24 22 16 13 12 8 7 6 5 4 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 126 98 82 63 56 46 35 30 25 20 17 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 110 92 70 55 48 40 32 27 22 19 17 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Typ. Max. Typ. 0.009 7,800 9,300 6,200 7,600 0.012 6,200 7,800 5,300 6,400 0.015 4,900 6,100 4,800 5,600 0.019 4,200 5,200 4,300 5,100 0.022 3,600 4,400 4,000 4,700 0.029 3,000 3,600 3,400 4,000 0.033 2,400 2,900 3,000 3,600 0.060 2,000 2,300 2,200 2,600 0.070 1,750 2,200 1,900 2,300 0.120 1,300 1,600 1,500 1,800 0.170 1,100 1,400 1,300 1,500 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 电感器 NRS8030T NRS8030T NRS8030T NRS8030T NRS8030T NRS8030T NRS8030T NRS8030T NRS8030T NRS8030T NRS8030T EHS ●NRS8040屏蔽型 型号 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 功率电感器 NRS8040T 0R9NJGJ NRS8040T 1R0NJGJ NRS8040T 1R4NJGJ NRS8040T 1R5NJGJ NRS8040T 2R0NJGJ NRS8040T 2R2NJGJ NRS8040T 3R3NJGJ NRS8040T 3R6NJGJ NRS8040T 4R7NJGJ NRS8040T 6R8NJGJ NRS8040T 100MJGJ NRS8040T 150MJGJ NRS8040T 220MJGJ NRS8040T 330MJGK NRS8040T 470MJGK NRS8040T 680MJGK NRS8040T 101MJGK NRS8040T 151MJGK NRS8040T 221MJGK 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Typ. Max. Typ. 0.006 13,000 14,000 7,800 9,600 0.006 13,000 14,000 7,800 9,600 0.007 10,000 11,000 7,000 8,400 0.007 10,000 11,000 7,000 8,400 0.009 8,100 9,200 6,300 7,600 0.009 8,100 9,200 6,300 7,600 0.015 6,400 6,800 4,900 6,000 0.015 6,400 6,800 4,900 6,000 0.018 5,400 5,900 4,100 5,200 0.025 4,400 4,800 3,700 4,400 0.034 3,800 4,100 3,100 3,500 0.050 2,900 3,200 2,400 3,000 0.066 2,400 2,700 2,200 2,600 0.100 2,000 2,300 1,700 1,900 0.140 1,500 1,800 1,500 1,600 0.210 1,300 1,500 1,200 1,300 0.280 1,100 1,300 1,000 1,100 0.420 900 980 800 890 0.620 700 800 670 740 ●NR 3010屏蔽型 型号 NR NR NR NR NR NR NR NR NR NR NR 3010T 3010T 3010T 3010T 3010T 3010T 3010T 3010T 3010T 3010T 3010T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Max. 1,300 1,400 0.065 1,200 1,300 0.080 1,100 1,100 0.095 870 940 0.140 750 780 0.190 610 630 0.300 500 510 0.450 400 400 0.740 350 350 1.03 260 275 1.55 220 235 2.05 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 ●NR 3012屏蔽型 型号 NR NR NR NR NR NR NR NR NR NR NR 3012T 3012T 3012T 3012T 3012T 3012T 3012T 3012T 3012T 3012T 3012T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Max. 1,500 1,490 0.050 1,360 1,400 0.060 1,100 1,200 0.080 910 1,050 0.100 770 980 0.130 670 740 0.190 540 630 0.290 440 485 0.450 375 420 0.630 310 330 1.03 250 280 1.45 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 59 for General Electronic Equipment ■型号一览 ●NR 3015屏蔽型 型号 电感器 NR NR NR NR NR NR NR NR NR NR NR 3015T 3015T 3015T 3015T 3015T 3015T 3015T 3015T 3015T 3015T 3015T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 100 87 64 49 40 36 28 23 20 18 17 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 116 73 58 47 38 31 24 19 15 13 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 131 66 50 45 35 28 23 18 15 12 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 80 52 44 34 29 24 19 16 12 10 8.3 6.5 5.5 4.0 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 60 42 32 28 21 18 13 9 7 6 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Max. 2,100 2,100 0.030 1,800 1,820 0.040 1,480 1,500 0.060 1,210 1,230 0.080 1,020 1,040 0.120 870 880 0.160 700 710 0.230 560 560 0.360 470 470 0.520 390 370 0.840 320 300 1.34 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 ●NR 4010屏蔽型 型号 功率电感器 EHS NR NR NR NR NR NR NR NR NR NR 4010T 4010T 4010T 4010T 4010T 4010T 4010T 4010T 4010T 4010T 1R0N 2R2N 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Max. 1,800 1,050 0.100 1,150 890 0.150 1,100 820 0.180 900 750 0.210 740 620 0.300 560 600 0.380 470 510 0.510 360 400 0.870 280 300 1.54 240 280 1.81 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 ●NR 4012屏蔽型 型号 NR NR NR NR NR NR NR NR NR NR 4012T 4012T 4012T 4012T 4012T 4012T 4012T 4012T 4012T 4012T 1R0N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Max. 2,500 1,500 0.060 1,650 1,200 0.090 1,200 980 0.130 1,050 960 0.140 900 840 0.180 740 770 0.240 560 600 0.400 510 540 0.480 400 420 0.810 350 370 1.00 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 ●NR 4018屏蔽型 型号 NR NR NR NR NR NR NR NR NR NR NR NR NR NR 4018T 4018T 4018T 4018T 4018T 4018T 4018T 4018T 4018T 4018T 4018T 4018T 4018T 4018T 1R0N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M 680M 101M 151M 221M 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Max. 4,000 1,830 0.030 2,700 1,440 0.060 2,000 1,230 0.070 1,700 1,200 0.090 1,450 1,060 0.110 1,200 840 0.180 940 650 0.250 800 590 0.360 650 490 0.530 570 420 0.650 470 320 1.00 400 270 1.50 310 220 2.50 270 170 4.00 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 ●NR 5040屏蔽型 型号 NR NR NR NR NR NR NR NR NR NR 5040T 1R5N 5040T 2R2N 5040T 3R3N 5040T 4R7N 5040T 6R8M 5040T 100M 5040T 150M 5040T 220M 5040T 330M 5040T 470M 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Max. 6,000 3,600 0.020 4,600 3,500 0.022 3,800 3,300 0.027 3,300 3,100 0.029 2,600 2,300 0.049 2,300 2,100 0.056 2,000 1,800 0.080 1,600 1,400 0.126 1,300 1,200 0.180 1,100 900 0.310 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 60 21 for General Electronic Equipment ■型号一览 ●NR 6012屏蔽型 型号 6012T 6012T 6012T 6012T 6012T 6012T 6012T 6012T 6012T 6012T 6012T 2R5NE 4R0NE 5R3ME 6R8ME 100ME 150ME 220ME 330ME 470ME 680ME 101ME 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 2.5 4.0 5.3 6.8 10 15 22 33 47 68 100 ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 45 39 34 30 22 18 12 8 6 3 1 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.8 1.5 2.2 3.3 4.7 6.8 10 22 ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ 110 93 73 55 43 30 18 11 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.9 1.5 2.2 3.0 4.7 6.0 10 15 22 33 47 68 100 ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 90 78 68 55 39 30 20 17 12 10 8 5 3 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.3 1.8 2.3 3.0 4.5 6.3 10 15 22 33 47 68 100 ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 110 95 80 60 45 25 15 12 10 7 6 5 4 3 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.9 1.4 2.0 3.6 4.7 6.8 10 15 22 33 47 68 100 ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 85 63 50 34 30 24 22 16 13 12 8 7 6 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Max. 2,100 1,730 0.090 1,800 1,570 0.105 1,500 1,400 0.125 1,300 1,180 0.165 1,000 1,000 0.235 800 790 0.330 760 630 0.530 590 530 0.700 520 460 1.05 440 410 1.35 350 320 2.18 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 电感器 NR NR NR NR NR NR NR NR NR NR NR EHS ●NR 6020屏蔽型 型号 6020T 6020T 6020T 6020T 6020T 6020T 6020T 6020T 0R8N 1R5N 2R2N 3R3N 4R7N 6R8N 100M 220M 测试频率［kHz］ 100 100 100 100 100 100 100 100 功率电感器 NR NR NR NR NR NR NR NR 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±20％） Max. Max. 5,500 3,800 0.020 4,000 3,200 0.026 3,200 2,700 0.034 2,800 2,600 0.040 2,400 2,000 0.058 2,000 1,800 0.085 1,700 1,400 0.125 1,050 950 0.290 ●NR 6028屏蔽型 型号 NR NR NR NR NR NR NR NR NR NR NR NR NR 6028T 0R9N 6028T 1R5N 6028T 2R2N 6028T 3R0N 6028T 4R7M 6028T 6R0M 6028T 100M 6028T 150M 6028T 220M 6028T 330M 6028T 470M 6028T 680M 6028T 101M 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Max. 6,600 4,600 0.013 5,000 4,200 0.016 4,200 3,700 0.020 3,600 3,400 0.023 2,700 3,000 0.031 2,500 2,500 0.040 1,900 1,900 0.065 1,600 1,800 0.095 1,300 1,400 0.135 1,100 1,100 0.220 950 920 0.300 760 770 0.420 620 660 0.600 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 ●NR 6045屏蔽型 型号 NR 6045T 1R0N NR 6045T 1R3N NR 6045T 1R8N NR 6045T 2R3N NR 6045T 3R0N NR 6045T 4R5M NR 6045T 6R3M NR 6045T 100M NR 6045T 150M NR 6045T 220M NR 6045T 330M NR 6045T 470M NR 6045T 680M NR 6045T 101M 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Max. 8,500 4,200 0.014 8,000 4,000 0.016 7,000 3,700 0.018 6,000 3,500 0.021 5,000 3,200 0.024 4,000 3,000 0.031 3,800 2,800 0.038 3,000 2,500 0.047 2,300 1,900 0.077 1,900 1,500 0.115 1,500 1,400 0.145 1,300 1,100 0.220 1,000 900 0.330 800 700 0.500 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 ●NR 8040屏蔽型 型号 NR NR NR NR NR NR NR NR NR NR NR NR NR 8040T 0R9N 8040T 1R4N 8040T 2R0N 8040T 3R6N 8040T 4R7N 8040T 6R8N 8040T 100M 8040T 150M 8040T 220M 8040T 330M 8040T 470M 8040T 680M 8040T 101M 额定电流　※）［ｍA］ 直流电阻 直流重叠允许电流： Idc1 温度上升允许电流： Idc2 ［Ω］（±30％） Max. Max. 11,000 7,800 0.006 9,000 7,000 0.007 7,400 6,300 0.009 5,300 4,900 0.015 4,700 4,100 0.018 4,000 3,700 0.025 3,400 3,100 0.034 2,700 2,400 0.050 2,200 2,200 0.066 1,900 1,700 0.100 1,500 1,400 0.150 1,200 1,100 0.230 1,000 1,000 0.290 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 61 SMD POWER INDUCTORS (NR SERIES/NR SERIES H TYPE/M TYPE/S TYPE/V TYPE) ■PACKAGING ①Minimum Quantity Standard Quantity [pcs] Tape ＆ Reel 2500 Type NRV2010 NRS2012 NRV2012 NRH2410 NRH2412 NR 3010 NRH3010 NR 3012 NRH3012 NRV3012 NR 3015 NRS3015 NR 4010 NRS4010 NR 4012 NRS4012 NR 4018 NRS4018 Standard Quantity [pcs] Tape ＆ Reel 1000 1000 1000 800 2500 500 Type NRS5010 NRS5012 NRS5014 NRS5020 NRS5024 NRS5030 NR 5040 NRS5040 NRS6010 NR 6012 NRS6012 NRS6014 NR 6020 NRS6020 NR 6028 NRS6028 NR 6045 NRM6045 NRS6045 NRS8030 NR 8040 NRS8040 2500 2500 2500 2000 2000 2000 5000 4500 3500 1500 1000 1000 1000 2500 2000 1500 1000 1000 ②Tape Material ●Embossed Tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip ③Taping dimensions ●Embossed tape 8mm wide (0.315 inches wide) 1.75±0.1 (0.069±0.004） A B T 8.0±0.2 (0.315±0.008) φ1.5＋0.1/－0 (φ0.059＋0.004/-0) 3.5±0.1 (0.138±0.004) Sprocket hole K F 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) Electrode（bottom view） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_pack_e-E07R01 Chip cavity Type NRV2010 NRS2012 NRV2012 NRH2410 NRH2412 NR 3010 NRH3010 NR 3012 NRH3012 NRV3012 NR 3015 NRS3015 A B 2.2±0.1 （0.102±0.004） 2.6±0.1 （0.087±0.004） Insertion pitch F Tape thickness T K 2.2±0.1 （0.102±0.004） 0.25±0.05 （0.009±0.002） 1.3±0.1 （0.051±0.004） 2.6±0.1 （0.102±0.004） 0.25±0.05 （0.009±0.002） 1.3±0.1 （0.051±0.004） 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 4.0±0.1 （0.157±0.004） 3.2±0.1 （0.126±0.004） 3.2±0.1 （0.126±0.004） 0.3±0.05 （0.012±0.002） 1.9±0.1 （0.075±0.004） Unit：mm（inch） ●Embossed tape 12mm wide (0.47 inches wide) 1.75±0.1 (0.069±0.004） A B T 12.0±0.3 (0.472±0.012) φ1.5＋0.1/－0 (φ0.059＋0.004/-0) 5.5±0.1 (0.217±0.004) Sprocket hole K F Type NR 4010 NRS4010 NR 4012 NRS4012 NR 4018 NRS4018 2.0±0.1 (0.079±0.004) 4.0±0.1 (0.157±0.004) Electrode（bottom view） Chip cavity A B 4.3±0.1 （0.169±0.004） 4.3±0.1 （0.169±0.004） Insertion pitch F NRS5010 0.3±0.1 （0.012±0.004） NRS5012 NRS5014 Tape thickness T 5.25±0.1 （0.207±0.004） 5.25±0.1 （0.207±0.004） 5.15±0.1 （0.203±0.004） 5.15±0.1 （0.203±0.004） 5.15±0.1 （0.203±0.004） 5.15±0.1 （0.203±0.004） NRS5020 NRS5024 NRS5030 NR 5040 NRS5040 8.0±0.1 （0.315±0.004） NRS6010 NR 6012 NRS6012 0.4±0.1 （0.016±0.004） NRS6014 NR 6020 NRS6020 NR 6028 NRS6028 NR 6045 NRM6045 NRS6045 6.3±0.1 （0.248±0.004） 6.3±0.1 （0.248±0.004） K 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 2.1±0.1 （0.083±0.004） 1.4±0.1 （0.055±0.004） 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 2.3±0.1 （0.091±0.004） 2.7±0.1 （0.106±0.004） 3.2±0.1 （0.126±0.004） 4.2±0.1 （0.165±0.004） 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 1.6±0.1 （0.063±0.004） 2.3±0.1 （0.090±0.004） 3.1±0.1 （0.122±0.004） 4.7±0.1 （0.185±0.004） Unit：mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_pack_e-E07R01 ●Embossed tape 16mm wide (0.63 inches wide) φ1.5±0.1 (φ0.059±0.004） Sprocket hole 1.75±0.1 (0.069±0.004） A B 16.0±0.3 (0.630±0.012) 7.5±0.1 (0.295±0.004) T K F 2.0±0.1 (0.079±0.004) Type NRS8030 NR 8040 NRS8040 4.0±0.1 (0.157±0.004) Electrode（bottom view） A Chip cavity B Insertion pitch F T Tape thickness 8.3±0.1 （0.327±0.004） 8.3±0.1 （0.327±0.004） 12.0±0.1 （0.472±0.004） 0.5±0.1 （0.020±0.004） φD Reel size (Reference values) φd W 180±0.5 （7.087±0.019） 60±1.0 （2.36±0.04） 10.0±1.5 （0.394±0.059） K 3.4±0.1 （0.134±0.004） 4.5±0.1 （0.177±0.004） Unit：mm（inch） ④Leader and Blank portion ●NR, NRH, NRS, NRV ⑤Reel size Type NRV2010 NRS2012 NRV2012 NRH2410 NRH2412 NR 3010 NRH3010 NR 3012 NRH3012 NRV3012 NR 3015 NRS3015 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_pack_e-E07R01 NRS5010 NRS5012 NRS5014 NRS5020 NRS5030 NRS6010 NR 6012 NRS6012 NRS6014 180±3.0 （7.087±0.118） 60±2.0 （2.36±0.08） 14.0±1.5 （0.551±0.059） Unit：mm（inch） Type NR 4010 NRS4010 NR 4012 NRS4012 NR 4018 NRS4018 NRS5024 NR 5040 NRS5040 NR 6020 NRS6020 NR 6028 NRS6028 NR 6045 NRM6045 NRS6045 NRS8030 NR 8040 NRS8040 φD 330±3.0 （12.99±0.118） Reel size (Reference values) φd t（max.） 80±2.0 （3.15±0.078） W 18.5 （0.72） 13.5±1.0 （0.531±0.04） 22.5 （0.89） 17.5±1.0 （0.689±0.04） Unit：mm（inch） ⑥Top Tape Strength The top tape requires a peel-off force of 0.1 to 1.3N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_pack_e-E07R01 SMD POWER INDUCTORS（NR□, NS SERIES） ■RELIABILITY DATA 1. Operating Temperature Range Specified Value Test Methods and Remarks NR30/40/50/60/80, NRS20, NRV20/30, NRH24/30 Type －25～＋120℃ NRS40/50/60/80 Type －25～＋125℃ NR10050 Type －25～＋105℃ NS101, NS125 Type －40～＋125℃ Including self-generated heat 2. Storage Temperature Range NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value －40～＋85℃ NR10050 Type NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type： －5 to 40℃ for the product with taping. 3. Rated current NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Within the specified tolerance NR10050 Type NS101, NS125 Type 4. Inductance NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Within the specified tolerance NR10050 Type NS101, NS125 Type Test Methods and Remarks Measuring equipment : LCR Meter （HP 4285A or equivalent） Measuring frequency : Specified frequency NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type Measuring equipment : LCR Meter （HP 4285A or equivalent） Measuring frequency : 100kHz, 1V NR10050 Type : Measuring equipment : LCR Meter （HP 4263A or equivalent） Measuring frequency : 100kHz, 1V : 5. DC Resistance NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Within the specified tolerance NR10050 Type NS101, NS125 Type Test Methods and Remarks Measuring equipment : DC ohmmeter （HIOKI 3227 or equivalent） 6. Self resonance frequency NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type Specified Value NS101, NS125 Type Test Methods and Remarks Within the specified tolerance NR10050 Type － NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type, NR10050 Type : Measuring equipment : Impedance analyzer/material analyzer（HP4291A or equivalent HP4191A, 4192A or equivalent） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 7. Temperature characteristic NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Inductance change : Within ±20% NR10050 Type NS101, NS125 Type Inductance change : Within ±15% NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type : Measurement of inductance shall be taken at temperature range within －25℃～＋85℃. With reference to inductance value at ＋20℃., change rate shall be calculated. Test Methods and Remarks NS101, NS125 Type : Measurement of inductance shall be taken at temperature range within －40℃～＋125℃. With reference to inductance value at ＋20℃., change rate shall be calculated. Change of maximum inductance deviation in step 1 to 5 Step Temperature（℃） 1 20 2 Minimum operating temperature 3 20 (Standard temperature) 4 Maximum operating temperature 5 20 8. Resistance to flexure of substrate Specified Value NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type No damage NR10050 Type － NS101, NS125 Type No damage NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. As illustrated below, apply force in the direction of the arrow indicating until deflection of the test board reaches to 2 mm. Test board size : 100×40×1.0 Test board material : Glass epoxy-resin Solder cream thickness : 0.10mm (NR30, NRS20, NRH24/30, NRV20/30) : 0.15mm(NR40/50/60/80, NRS40/50/60, NS101/125Type) Test Methods and Remarks Land dimension C A B A Type NRS20, NRV20 NRH24 NR30, NRV30, NRH30 NR40, NRS40 NR50, NRS50 NR60, NRS60 NR80, NRS80 A 0.65 0.7 0.8 1.2 1.5 1.6 1.8 B 0.7 0.75 1.4 1.6 2.1 3.1 3.8 C 2.0 2.0 2.7 3.7 4.0 5.7 7.5 Type NS101 NS125 A 2.5 2.5 B 5.6 8.6 C 3.2 3.2 9. Insulation resistance : between wires NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type － NS101, NS125 Type 10. Insulation resistance : between wire and core NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type － NS101, NS125 Type ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 11. Withstanding voltage : between wire and core NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value － NR10050 Type NS101, NS125 Type 12. Adhesion of terminal electrode NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Shall not come off PC board NR10050 Type NS101, NS125 Type NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. Applied force : 10N to X and Y directions. Duration : 5s. Solder cream thickness : 0.10mm (NR30, NRS20, NRH24/30, NRV20/30) : 0.15mm (NR40/50/60/80, NRS40/50/60, NS101/125Type) Test Methods and Remarks NR10050 Type Applied force Duration : 5N to X and Y directions. : 5s. 13. Resistance to vibration NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. Then it shall be submitted to below test conditions. Test Methods and Remarks Frequency Range Total Amplitude Sweeping Method Time 10～55Hz 1.5mm (May not exceed acceleration 196m/s2) 10Hz to 55Hz to 10Hz for 1min. X Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 14. Solderability NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type At least 90％ of surface of terminal electrode is covered by new solder. NS101, NS125 Type Test Methods and Remarks The test samples shall be dipped in flux, and then immersed in molten solder as shown in below table. Flux : Methanol solution containing rosin 25%. NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type Solder Temperature 245±5℃ Time 5±1.0 sec. ※Immersion depth : All sides of mounting terminal shall be immersed. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 15. Resistance to soldering heat NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test sample shall be exposed to reflow oven at 230±5℃ for 40 seconds, with peak temperature at 260±5℃ for 5 seconds, 2 times. Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80Type, NS101/125 Type Test board material : Glass epoxy-resin Test board thickness : 1.0mm NR10050 Type Test board material : Glass epoxy-resin Test board thickness : 1.6mm Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 16. Thermal shock NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. The test samples shall be placed at specified temperature for specified time by step 1 to step 4 as shown in below table in sequence. The temperature cycle shall be repeated 100 cycles. Conditions of 1 cycle Step Temperature (℃) Duration (min) 1 －40±3 30±3 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 17. Damp heat Specified Value Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10% No significant abnormality in appearance. NR10050 Type － NS101, NS125 Type Inductance change : Within ±10% No significant abnormality in appearance. NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. The test samples shall be placed in thermostatic oven set at specified temperature and humidity as shown in below table. Temperature 60±2℃ Humidity 90～95%RH Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 18. Loading under damp heat NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. The test samples shall be placed in thermostatic oven set at specified temperature and humidity and applied the rated current continuously as shown in below table. Temperature 60±2℃ Humidity 90～95％RH Applied current Rated current Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 19. Low temperature life test NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. After that, the test samples shall be placed at test conditions as shown in below table. Temperature －40±2℃ Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 20. High temperature life test Specified Value Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type － NR10050 Type － NS101, NS125 Type － NR10050 Type : Temperature 105±3℃ Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 21. Loading at high temperature life test Specified Value Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10% No significant abnormality in appearance. NR10050 Type － NS101, NS125 Type Inductance change : Within ±10% No significant abnormality in appearance. NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type, NS12555, NS12565, NS12575 Type : The test samples shall be soldered to the test board by the reflow soldering. Temperature 85±2℃ Applied current Rated current Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 22. Standard condition NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type NS101, NS125 Type Standard test condition : Unless otherwise specified, temperature is 20±15℃ and 65±20％of relative humidity. When there is any question concerning measurement result: In order to provide correlation data, the test shall be condition of 20±2℃ of temperature, 65±5% relative humidity. Inductance is in accordance with our measured value. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 SMD POWER INDUCTORS（NR□, NS SERIES） ■PRECAUTIONS 1. Circuit Design Precautions ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Precautions ◆Land pattern design 1. Please refer to a recommended land pattern. 2. There is stress, which has been caused by distortion of a PCB, to the inductor. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) 3. Please consider the arrangement of parts on a PCB. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) ◆Land pattern design Surface Mounting 1. Mounting and soldering conditions should be checked beforehand. 2. Applicable soldering process to this products is reflow soldering only. 3. Please use the recommended land pattern shown as below. Electrical characteristics and the mounting ability of the product are being considered in the recommended land pattern. If a PCB is designed with other dimensions, defective soldering and stress to a product may occur due to misalignment. The performance of the product may not be brought out. If an adopted land pattern is different from the recommended land pattern, stress to the product will increase. It may cause cracks or defective electrical characteristics of the product. Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) 4. As coefficients of thermal expansion between an inductor and a PCB differs, cracks may occur on a ferrite core when thermal stress is applied to them after mounting an inductor. (Please refer to the drawings below.) Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) Clack on ferrite core Technical considerations Solder, electrode PCB 5. SMD inductors should be located to minimize any possible mechanical stresses from board warp or deflection. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection or twisting to the board. （NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type） A product tends to undergo stress in order “A>C>B≡D”. Please consider the layouts of a product to minimize any stresses. Electrode A Perforation Slit D B C ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) i_smd_NR_NS_prec_e-E06R01 3. Considerations for automatic placement Precautions ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. ◆Adjustment of mounting machine 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 2. Stress may be applied to a product with a warp or a twist in handling of the product. Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) Technical considerations ＜Wrap＞ ＜Twist＞ 4. Soldering Precautions ◆Reflow soldering 1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified. 2. The product shall be used reflow soldering only. 3. Please do not add any stress to a product until it returns in normal temperature after reflow soldering. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. ◆Recommended conditions for using a soldering iron (NR10050 Type) ・ Put the soldering iron on the land-pattern. ・ Soldering iron's temperature - Below 350℃ ・ Duration - 3 seconds or less ・ The soldering iron should not directly touch the inductor. ◆Reflow soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. ・NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type Recommended reflow condition (Pb free solder) Technical considerations 5. Cleaning Precautions Technical considerations ◆Cleaning conditions 1. Washing by supersonic waves shall be avoided. ◆Cleaning conditions 1. If washed by supersonic waves, the products might be broken. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) i_smd_NR_NS_prec_e-E06R01 6. Handling Precautions Technical considerations ◆Handling 1. Keep the product away from all magnets and magnetic objects. ◆Breakaway PC boards (splitting along perforations) 1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1. Please do not give the product any excessive mechanical shocks. 2. Please do not add any shock and power to a product in transportation. ◆Pick-up pressure 1. Please do not push to add any pressure to a winding part. Please do not give any shock and push into a ferrite core exposure part. ◆Packing 1. Please avoid accumulation of a packing box as much as possible. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Breakaway PC boards (splitting along perforations) 1. The position of the product on PCBs shall be carefully considered to minimize the stress caused from splitting of the PCBs. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 2. There is a case to be broken by the handling in transportation. ◆Pick-up pressure 1. Damage and a characteristic can vary with an excessive shock or stress. ◆Packing 1. If packing boxes are accumulated, that could cause a deformation on packing tapes or a damage on the products. 7. Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : －5～40℃ Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) i_smd_NR_NS_prec_e-E06R01 for General Electronic Equipment SMD 功率电感器 SMD 功率电感器 *使用温度范围：-25～+105℃（包含产品本身发热） ■型号标示法 N R △ ① 1 0 0 5 ② 电感器 ①类型 代码 NR△ 0 T △ ③ 1 0 0 ④ M △ ⑤ ⑥ ④标称电感值 代码（例） 1R3 100 101 ※R＝小数点 类型 外装树脂规格 ②尺寸（L×H） 代码 10050 尺寸（L×H） ［mm］ 10.0×5.0 功率电感器 ③包装 代码 T△ △＝空格 标称电感值［μH］ 1.3 10 100 ⑤电感量公差 代码 M N 包装 卷盘带装 电感量公差 ±20％ ±30％ ⑥本公司管理记号 代码 △ 本公司管理记号 标准品 ■标准外型尺寸／标准数量 推荐焊盘图案 実装上的注意 ・请确认実装状态后使用。 ・本产品焊法限定为回流焊法。 a L b W b 4.5 H 2.6 5.4 2.6 单位：mm Type L W H a b NR 10050 10.0±0.3 （0.394±0.012） 9.8±0.5 （0.386±0.020） 5.0 max （0.197 max） 4.0 （0.16） 1.75 （0.07） 标准数量［pcs］ 卷盘带装 500 单位：mm（inch） i_smd_NR10050_j-E08R01-c.doc ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 62 21 for General Electronic Equipment ■型号一览 ●NR 10050型 型号 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.3 2.1 2.9 3.8 4.9 6.5 10 15 22 33 47 68 100 220 ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 53 37 29 26 23 19 15 11 10 8.2 7.0 5.6 4.6 3.0 0.0068 0.0080 0.0093 0.013 0.015 0.018 0.025 0.035 0.045 0.066 0.092 0.144 0.209 0.450 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 11,000 10,000 8,200 7,300 6,600 6,000 4,700 3,600 2,600 2,500 2,000 1,700 1,300 1,000 9,000 8,300 7,300 6,800 6,000 5,200 4,100 3,200 2,500 2,100 1,800 1,500 1,200 800 测试频率 ［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 电感器 NR 10050T 1R3N NR 10050T 2R1N NR 10050T 2R9N NR 10050T 3R8N NR 10050T 4R9N NR 10050T 6R5N NR 10050T 100M NR 10050T 150M NR 10050T 220M NR 10050T 330M NR 10050T 470M NR 10050T 680M NR 10050T 101M NR 10050T 221M EHS 功率电感器 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）最大额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值（at 20℃） i_smd_NR10050_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 63 SMD POWER INDUCTORS ■PACKAGING ①Minimum Quantity Standard Quantity [pcs] Tape & Reel 500 Type NR 10050 ②Tape Material ●Embossed Tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip ③Taping dimensions ●Embossed tape 24mm wide (0.945 inches wide) 11.5±0.1 (0.453±0.004） 1.75±0.1 (0.069±0.004） A B F 2.0±0.1 (0.079±0.004) Type NR 10050 24.0＋0.3/－0.1 （0.945＋0.012/－0.004） φ1.5＋0.1/－0 (φ0.059＋0.004/-0) Sprocket hole T K 4.0±0.1 (0.157±0.004) Chip cavity A B 10.4±0.1 9.9±0.1 （0.409±0.004） （0.390±0.004） Insertion pich F 16.0±0.1 （0.630±0.004） Tape thickness T K 0.5±0.05 5.7±0.1 （0.020±0.002） （0.224±0.004） Unit：mm（inch） ④Leader and Blank portion ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR10050_pack_e-E05R01 ⑤Reel size Type NR 10050 φD 330±3 （12.99±0.118） Reel size (Reference valus φd 80±2 （3.15±0.078） t（max.） 30.5 （1.201） Unit：mm（inch） ⑥Top Tape Strength The top tape requires a peel-off force of 0.1 to 1.3N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR10050_pack_e-E05R01 SMD POWER INDUCTORS（NR□, NS SERIES） ■RELIABILITY DATA 1. Operating Temperature Range Specified Value Test Methods and Remarks NR30/40/50/60/80, NRS20, NRV20/30, NRH24/30 Type －25～＋120℃ NRS40/50/60/80 Type －25～＋125℃ NR10050 Type －25～＋105℃ NS101, NS125 Type －40～＋125℃ Including self-generated heat 2. Storage Temperature Range NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value －40～＋85℃ NR10050 Type NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type： －5 to 40℃ for the product with taping. 3. Rated current NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Within the specified tolerance NR10050 Type NS101, NS125 Type 4. Inductance NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Within the specified tolerance NR10050 Type NS101, NS125 Type Test Methods and Remarks Measuring equipment : LCR Meter （HP 4285A or equivalent） Measuring frequency : Specified frequency NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type Measuring equipment : LCR Meter （HP 4285A or equivalent） Measuring frequency : 100kHz, 1V NR10050 Type : Measuring equipment : LCR Meter （HP 4263A or equivalent） Measuring frequency : 100kHz, 1V : 5. DC Resistance NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Within the specified tolerance NR10050 Type NS101, NS125 Type Test Methods and Remarks Measuring equipment : DC ohmmeter （HIOKI 3227 or equivalent） 6. Self resonance frequency NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type Specified Value NS101, NS125 Type Test Methods and Remarks Within the specified tolerance NR10050 Type － NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type, NR10050 Type : Measuring equipment : Impedance analyzer/material analyzer（HP4291A or equivalent HP4191A, 4192A or equivalent） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 7. Temperature characteristic NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Inductance change : Within ±20% NR10050 Type NS101, NS125 Type Inductance change : Within ±15% NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type : Measurement of inductance shall be taken at temperature range within －25℃～＋85℃. With reference to inductance value at ＋20℃., change rate shall be calculated. Test Methods and Remarks NS101, NS125 Type : Measurement of inductance shall be taken at temperature range within －40℃～＋125℃. With reference to inductance value at ＋20℃., change rate shall be calculated. Change of maximum inductance deviation in step 1 to 5 Step Temperature（℃） 1 20 2 Minimum operating temperature 3 20 (Standard temperature) 4 Maximum operating temperature 5 20 8. Resistance to flexure of substrate Specified Value NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type No damage NR10050 Type － NS101, NS125 Type No damage NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. As illustrated below, apply force in the direction of the arrow indicating until deflection of the test board reaches to 2 mm. Test board size : 100×40×1.0 Test board material : Glass epoxy-resin Solder cream thickness : 0.10mm (NR30, NRS20, NRH24/30, NRV20/30) : 0.15mm(NR40/50/60/80, NRS40/50/60, NS101/125Type) Test Methods and Remarks Land dimension C A B A Type NRS20, NRV20 NRH24 NR30, NRV30, NRH30 NR40, NRS40 NR50, NRS50 NR60, NRS60 NR80, NRS80 A 0.65 0.7 0.8 1.2 1.5 1.6 1.8 B 0.7 0.75 1.4 1.6 2.1 3.1 3.8 C 2.0 2.0 2.7 3.7 4.0 5.7 7.5 Type NS101 NS125 A 2.5 2.5 B 5.6 8.6 C 3.2 3.2 9. Insulation resistance : between wires NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type － NS101, NS125 Type 10. Insulation resistance : between wire and core NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type － NS101, NS125 Type ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 11. Withstanding voltage : between wire and core NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value － NR10050 Type NS101, NS125 Type 12. Adhesion of terminal electrode NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Shall not come off PC board NR10050 Type NS101, NS125 Type NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. Applied force : 10N to X and Y directions. Duration : 5s. Solder cream thickness : 0.10mm (NR30, NRS20, NRH24/30, NRV20/30) : 0.15mm (NR40/50/60/80, NRS40/50/60, NS101/125Type) Test Methods and Remarks NR10050 Type Applied force Duration : 5N to X and Y directions. : 5s. 13. Resistance to vibration NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. Then it shall be submitted to below test conditions. Test Methods and Remarks Frequency Range Total Amplitude Sweeping Method Time 10～55Hz 1.5mm (May not exceed acceleration 196m/s2) 10Hz to 55Hz to 10Hz for 1min. X Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 14. Solderability NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type At least 90％ of surface of terminal electrode is covered by new solder. NS101, NS125 Type Test Methods and Remarks The test samples shall be dipped in flux, and then immersed in molten solder as shown in below table. Flux : Methanol solution containing rosin 25%. NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type Solder Temperature 245±5℃ Time 5±1.0 sec. ※Immersion depth : All sides of mounting terminal shall be immersed. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 15. Resistance to soldering heat NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test sample shall be exposed to reflow oven at 230±5℃ for 40 seconds, with peak temperature at 260±5℃ for 5 seconds, 2 times. Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80Type, NS101/125 Type Test board material : Glass epoxy-resin Test board thickness : 1.0mm NR10050 Type Test board material : Glass epoxy-resin Test board thickness : 1.6mm Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 16. Thermal shock NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. The test samples shall be placed at specified temperature for specified time by step 1 to step 4 as shown in below table in sequence. The temperature cycle shall be repeated 100 cycles. Conditions of 1 cycle Step Temperature (℃) Duration (min) 1 －40±3 30±3 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 17. Damp heat Specified Value Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10% No significant abnormality in appearance. NR10050 Type － NS101, NS125 Type Inductance change : Within ±10% No significant abnormality in appearance. NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. The test samples shall be placed in thermostatic oven set at specified temperature and humidity as shown in below table. Temperature 60±2℃ Humidity 90～95%RH Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 18. Loading under damp heat NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. The test samples shall be placed in thermostatic oven set at specified temperature and humidity and applied the rated current continuously as shown in below table. Temperature 60±2℃ Humidity 90～95％RH Applied current Rated current Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 19. Low temperature life test NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. After that, the test samples shall be placed at test conditions as shown in below table. Temperature －40±2℃ Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 20. High temperature life test Specified Value Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type － NR10050 Type － NS101, NS125 Type － NR10050 Type : Temperature 105±3℃ Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 21. Loading at high temperature life test Specified Value Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10% No significant abnormality in appearance. NR10050 Type － NS101, NS125 Type Inductance change : Within ±10% No significant abnormality in appearance. NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type, NS12555, NS12565, NS12575 Type : The test samples shall be soldered to the test board by the reflow soldering. Temperature 85±2℃ Applied current Rated current Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 22. Standard condition NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type NS101, NS125 Type Standard test condition : Unless otherwise specified, temperature is 20±15℃ and 65±20％of relative humidity. When there is any question concerning measurement result: In order to provide correlation data, the test shall be condition of 20±2℃ of temperature, 65±5% relative humidity. Inductance is in accordance with our measured value. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 SMD POWER INDUCTORS（NR□, NS SERIES） ■PRECAUTIONS 1. Circuit Design Precautions ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Precautions ◆Land pattern design 1. Please refer to a recommended land pattern. 2. There is stress, which has been caused by distortion of a PCB, to the inductor. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) 3. Please consider the arrangement of parts on a PCB. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) ◆Land pattern design Surface Mounting 1. Mounting and soldering conditions should be checked beforehand. 2. Applicable soldering process to this products is reflow soldering only. 3. Please use the recommended land pattern shown as below. Electrical characteristics and the mounting ability of the product are being considered in the recommended land pattern. If a PCB is designed with other dimensions, defective soldering and stress to a product may occur due to misalignment. The performance of the product may not be brought out. If an adopted land pattern is different from the recommended land pattern, stress to the product will increase. It may cause cracks or defective electrical characteristics of the product. Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) 4. As coefficients of thermal expansion between an inductor and a PCB differs, cracks may occur on a ferrite core when thermal stress is applied to them after mounting an inductor. (Please refer to the drawings below.) Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) Clack on ferrite core Technical considerations Solder, electrode PCB 5. SMD inductors should be located to minimize any possible mechanical stresses from board warp or deflection. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection or twisting to the board. （NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type） A product tends to undergo stress in order “A>C>B≡D”. Please consider the layouts of a product to minimize any stresses. Electrode A Perforation Slit D B C ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) i_smd_NR_NS_prec_e-E06R01 3. Considerations for automatic placement Precautions ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. ◆Adjustment of mounting machine 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 2. Stress may be applied to a product with a warp or a twist in handling of the product. Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) Technical considerations ＜Wrap＞ ＜Twist＞ 4. Soldering Precautions ◆Reflow soldering 1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified. 2. The product shall be used reflow soldering only. 3. Please do not add any stress to a product until it returns in normal temperature after reflow soldering. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. ◆Recommended conditions for using a soldering iron (NR10050 Type) ・ Put the soldering iron on the land-pattern. ・ Soldering iron's temperature - Below 350℃ ・ Duration - 3 seconds or less ・ The soldering iron should not directly touch the inductor. ◆Reflow soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. ・NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type Recommended reflow condition (Pb free solder) Technical considerations 5. Cleaning Precautions Technical considerations ◆Cleaning conditions 1. Washing by supersonic waves shall be avoided. ◆Cleaning conditions 1. If washed by supersonic waves, the products might be broken. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) i_smd_NR_NS_prec_e-E06R01 6. Handling Precautions Technical considerations ◆Handling 1. Keep the product away from all magnets and magnetic objects. ◆Breakaway PC boards (splitting along perforations) 1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1. Please do not give the product any excessive mechanical shocks. 2. Please do not add any shock and power to a product in transportation. ◆Pick-up pressure 1. Please do not push to add any pressure to a winding part. Please do not give any shock and push into a ferrite core exposure part. ◆Packing 1. Please avoid accumulation of a packing box as much as possible. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Breakaway PC boards (splitting along perforations) 1. The position of the product on PCBs shall be carefully considered to minimize the stress caused from splitting of the PCBs. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 2. There is a case to be broken by the handling in transportation. ◆Pick-up pressure 1. Damage and a characteristic can vary with an excessive shock or stress. ◆Packing 1. If packing boxes are accumulated, that could cause a deformation on packing tapes or a damage on the products. 7. Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : －5～40℃ Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) i_smd_NR_NS_prec_e-E06R01 for General Electronic Equipment SMD 功率电感器（NS 系列） SMD 功率电感器（NS 系列） ■型号标示法 N S △ ① *使用温度范围：-40～+125℃（包含产品本身发热） 1 0 1 4 ② 5 电感器 ①类型 代码 NS△ T △ ③ 1 0 0 ④ M ⑤ N 功率电感器 尺寸（L×W×H）［mm］ 10.1×10.1×4.5 10.1×10.1×5.5 10.1×10.1×6.5 12.5×12.5×5.5 12.5×12.5×6.5 12.5×12.5×7.5 ③包装 代码 T△ △＝空格 ④标称电感值 代码（例） 1R0 100 101 ※R＝小数点 类型 屏蔽规格 ②尺寸（L×W×H） 代码 10145 10155 10165 12555 12565 12575 A ⑥ 标称电感值［μH］ 1.0 10 100 ⑤电感量公差 代码 M N 电感量公差 ±20％ ±30％ ⑥本公司管理记号 代码 N△ NA 包装 卷盘带装 本公司管理记号 ■标准外型尺寸／最小订货单位数量 a W H L Type NS 10145 NS 10155 NS 10165 NS 12555 NS 12565 NS 12575 L 10.1±0.3 （0.398±0.012） 10.1±0.3 （0.398±0.012） 10.1±0.3 （0.398±0.012） 12.5±0.3 （0.492±0.012） 12.5±0.3 （0.492±0.012） 12.5±0.3 （0.492±0.012） b W 10.1±0.3 （0.398±0.012） 10.1±0.3 （0.398±0.012） 10.1±0.3 （0.398±0.012） 12.5±0.3 （0.492±0.012） 12.5±0.3 （0.492±0.012） 12.5±0.3 （0.492±0.012） b H 4.5±0.35 （0.177±0.014） 5.5±0.35 （0.217±0.014） 6.5±0.35 （0.256±0.014） 5.5±0.35 （0.217±0.014） 6.5±0.35 （0.256±0.014） 7.5±0.35 （0.295±0.014） ※ NS 101□□型没有显示生产日期标记。 最小订货单位数量［pcs］ b 2.0±0.15 2000 （0.079±0.006） 2.0±0.15 2000 （0.079±0.006） 2.0±0.15 2000 （0.079±0.006） 2.0±0.15 2000 （0.079±0.006） 2.0±0.15 2000 （0.079±0.006） 2.0±0.15 2000 （0.079±0.006） 单位：mm（inch） a 2.8±0.1 （0.110±0.004） 2.8±0.1 （0.110±0.004） 2.8±0.1 （0.110±0.004） 3.0±0.1 （0.118±0.004） 3.0±0.1 （0.118±0.004） 3.0±0.1 （0.118±0.004） 推荐焊盘图案 実装上的注意 ・请确认実装状态后使用。 ・本产品焊法限定为回流焊法。 C A B A Type NS 10145 NS 10155 NS 10165 NS 12555 NS 12565 NS 12575 A 2.5 2.5 2.5 2.5 2.5 2.5 B 5.6 5.6 5.6 8.6 8.6 8.6 C 3.2 3.2 3.2 3.2 3.2 3.2 单位：mm i_smd_NS_j-E08R01-c.doc ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 64 21 for General Electronic Equipment ■型号一览 ●NS 10145型 电感量公差 直流电阻 ［Ω］（±20％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 5.6 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1000 1500 ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 0.0049 0.0060 0.0085 0.0100 0.0144 0.0181 0.0200 0.0248 0.0381 0.0520 0.0815 0.100 0.150 0.200 0.341 0.485 0.700 1.030 1.57 2.58 3.70 型号 EHS 标称电感值 ［μH］ 电感量公差 直流电阻 ［Ω］（±20％） 10155T 1R5NNA 10155T 2R2NNA 10155T 3R3NNA 10155T 4R7NNA 10155T 6R8NNA 10155T 100MNA 10155T 150MNA 10155T 220MNA RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.5 2.2 3.3 4.7 6.8 10 15 22 ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ 0.0060 0.0072 0.0097 0.0112 0.0159 0.0200 0.0284 0.0380 型号 EHS 标称电感值 ［μH］ 电感量公差 直流电阻 ［Ω］（±20％） 10165T 1R5NNA 10165T 2R2NNA 10165T 3R3NNA 10165T 4R7NNA 10165T 6R8NNA 10165T 100MNA 10165T 150MNA 10165T 220MNA RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.5 2.2 3.3 4.7 6.8 10 15 22 ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ 0.0062 0.0074 0.0086 0.0112 0.0140 0.0174 0.0250 0.0313 EHS 标称电感值 ［μH］ 电感量公差 直流电阻 ［Ω］（±20％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 6.0 10 15 22 33 47 68 100 150 220 330 470 680 1000 1500 ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 0.0140 0.0175 0.0233 0.0297 0.0415 0.0551 0.0797 0.117 0.176 0.270 0.410 0.520 0.760 1.12 1.73 NS 10145T 1R0NNA NS 10145T 1R5NNA NS 10145T 2R2NNA NS 10145T 3R3NNA NS 10145T 4R7NNA NS 10145T 5R6NNA NS 10145T 6R8NNA NS 10145T 100MNA NS 10145T 150MNA NS 10145T 220MNA NS 10145T 330MNA NS 10145T 470MNA NS 10145T 680MNA NS 10145T 101MNA NS 10145T 151MNA NS 10145T 221MNA NS 10145T 331MNA NS 10145T 471MNA NS 10145T 681MNA NS 10145T 102MNA NS 10145T 152MNA 额定电流　※）　［A］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 12.54 10.34 8.91 7.33 6.69 5.85 5.05 4.22 3.44 2.87 2.36 1.85 1.66 1.29 1.11 0.91 0.71 0.61 0.50 0.41 0.36 8.90 7.99 6.64 6.10 5.03 4.45 4.22 3.77 3.00 2.55 2.01 1.80 1.45 1.25 0.94 0.78 0.64 0.52 0.42 0.32 0.27 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 功率电感器 标称电感值 ［μH］ 电感器 EHS 型号 ●NS 10155型 NS NS NS NS NS NS NS NS 额定电流　※）　［A］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 11.90 10.00 8.50 7.40 6.00 4.49 4.03 3.37 8.39 7.61 6.49 6.01 4.98 4.40 3.65 3.12 测试频率［kHz］ 100 100 100 100 100 100 100 100 ●NS 10165型 NS NS NS NS NS NS NS NS 额定电流　※）　［A］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 13.60 10.80 9.30 7.70 6.00 5.20 4.50 3.60 8.04 7.32 6.76 5.88 5.22 4.66 3.84 3.41 测试频率［kHz］ 100 100 100 100 100 100 100 100 ●NS 12555型 型号 NS 12555T 6R0NN NS 12555T 100MN NS 12555T 150MN NS 12555T 220MN NS 12555T 330MN NS 12555T 470MN NS 12555T 680MN NS 12555T 101MN NS 12555T 151MN NS 12555T 221MN NS 12555T 331MN NS 12555T 471MN NS 12555T 681MN NS 12555T 102MN NS 12555T 152MN 额定电流　※）　［A］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 5.01 4.73 3.89 3.20 2.64 2.23 1.81 1.53 1.22 1.00 0.82 0.68 0.60 0.47 0.40 5.60 5.04 4.18 3.81 3.16 2.70 2.14 1.86 1.43 1.18 0.96 0.80 0.72 0.59 0.44 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NS_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 65 for General Electronic Equipment ■型号一览 ●NS 12565型 型号 电感器 NS 12565T 2R0NN NS 12565T 4R2NN NS 12565T 7R0NN NS 12565T 100MN NS 12565T 150MN NS 12565T 220MN NS 12565T 330MN NS 12565T 470MN NS 12565T 680MN NS 12565T 101MN NS 12565T 151MN NS 12565T 221MN EHS 标称电感值 ［μH］ 电感量公差 直流电阻 ［Ω］（±20％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 2.0 4.2 7.0 10 15 22 33 47 68 100 150 220 ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 0.0080 0.0126 0.0162 0.0199 0.0237 0.0310 0.0390 0.0575 0.0775 0.123 0.173 0.273 EHS 标称电感值 ［μH］ 电感量公差 直流电阻 ［Ω］（±20％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.2 2.7 3.9 5.6 6.8 10 15 22 33 47 68 100 150 220 ±30％ ±30％ ±30％ ±30％ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 0.0058 0.0085 0.0099 0.0116 0.0131 0.0156 0.0184 0.0260 0.0390 0.0515 0.0720 0.110 0.161 0.245 额定电流　※）　［A］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 13.91 10.15 7.93 6.96 5.84 4.87 3.89 3.34 2.78 2.23 1.84 1.39 7.60 5.91 5.21 4.75 4.33 3.91 3.22 2.78 2.30 1.81 1.54 1.18 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 ●NS 12575型 型号 功率电感器 NS 12575T 1R2NN NS 12575T 2R7NN NS 12575T 3R9NN NS 12575T 5R6NN NS 12575T 6R8NN NS 12575T 100MN NS 12575T 150MN NS 12575T 220MN NS 12575T 330MN NS 12575T 470MN NS 12575T 680MN NS 12575T 101MN NS 12575T 151MN NS 12575T 221MN 额定电流　※）　［A］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 18.08 13.91 12.52 10.85 10.02 7.65 6.54 5.56 4.45 3.76 2.78 2.64 2.09 1.81 9.15 7.69 7.38 6.36 5.84 5.55 5.22 4.05 3.48 2.95 2.49 2.01 1.51 1.35 测试频率［kHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为能够满足直流重叠允许电流和温度上升允许电流的直流电流值 i_smd_NS_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 66 21 SMD POWER INDUCTORS (NS SERIES) ■PACKAGING ①Packing Quantity Standard Quantity (1reel) [pcs] Embossed Tape 500 500 500 500 500 500 Type NS10145 NS10155 NS10165 NS12555 NS12565 NS12575 Minimum Quantity [pcs] Embossed Tape 2000 2000 2000 2000 2000 2000 ②Tape Material ●Embossed Tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip ③Taping dimensions ●Embossed tape 24mm wide (0.945 inches wide) 11.5±0.1 (0.453±0.004） 1.75±0.1 (0.069±0.004） A B T 24.0±0.3 (0.945±0.012) φ1.5＋0.1/－0 (φ0.059＋0.004/-0) Sprocket hole K F Type NS10145 NS10155 NS10165 NS12555 NS12565 NS12575 2.0±0.1 (0.079±0.004) 4.0±0.1 (0.157±0.004) Chip cavity A B 10.5±0.1 10.5±0.1 （0.413±0.004） （0.413±0.004） 10.5±0.1 10.5±0.1 （0.413±0.004） （0.413±0.004） 10.5±0.1 10.5±0.1 （0.413±0.004） （0.413±0.004） 13.0±0.1 13.0±0.1 （0.512±0.004） （0.512±0.004） 13.0±0.1 13.0±0.1 （0.512±0.004） （0.512±0.004） 13.0±0.1 13.0±0.1 （0.512±0.004） （0.512±0.004） Insertion pitch F 16.0±0.1 （0.630±0.004） 16.0±0.1 （0.630±0.004） 16.0±0.1 （0.630±0.004） 16.0±0.1 （0.630±0.004） 16.0±0.1 （0.630±0.004） 16.0±0.1 （0.630±0.004） Tape thickness T K 0.4±0.1 5.0±0.1 （0.016±0.004） （0.197±0.004） 0.4±0.1 6.0±0.1 （0.016±0.004） （0.236±0.004） 0.4±0.1 7.0±0.1 （0.016±0.004） （0.276±0.004） 0.4±0.1 6.1±0.1 （0.016±0.004） （0.240±0.004） 0.4±0.1 7.1±0.1 （0.016±0.004） （0.280±0.004） 0.4±0.1 8.0±0.1 （0.016±0.004） （0.315±0.004） Unit：mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NS_pack_e-E05R01 ④Leader and Blank portion ⑤Reel size Type NS10145 NS10155 NS10165 NS12555 NS12565 NS12575 Reel size (Reference values) φD φd 330±2 （12.99±0.079） 100±1 （3.937±0.039） Unit：mm（inch） ⑥Top Tape Strength The top tape requires a peel-off force of 0.1 to 1.3N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NS_pack_e-E05R01 SMD POWER INDUCTORS（NR□, NS SERIES） ■RELIABILITY DATA 1. Operating Temperature Range Specified Value Test Methods and Remarks NR30/40/50/60/80, NRS20, NRV20/30, NRH24/30 Type －25～＋120℃ NRS40/50/60/80 Type －25～＋125℃ NR10050 Type －25～＋105℃ NS101, NS125 Type －40～＋125℃ Including self-generated heat 2. Storage Temperature Range NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value －40～＋85℃ NR10050 Type NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type： －5 to 40℃ for the product with taping. 3. Rated current NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Within the specified tolerance NR10050 Type NS101, NS125 Type 4. Inductance NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Within the specified tolerance NR10050 Type NS101, NS125 Type Test Methods and Remarks Measuring equipment : LCR Meter （HP 4285A or equivalent） Measuring frequency : Specified frequency NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type Measuring equipment : LCR Meter （HP 4285A or equivalent） Measuring frequency : 100kHz, 1V NR10050 Type : Measuring equipment : LCR Meter （HP 4263A or equivalent） Measuring frequency : 100kHz, 1V : 5. DC Resistance NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Within the specified tolerance NR10050 Type NS101, NS125 Type Test Methods and Remarks Measuring equipment : DC ohmmeter （HIOKI 3227 or equivalent） 6. Self resonance frequency NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type Specified Value NS101, NS125 Type Test Methods and Remarks Within the specified tolerance NR10050 Type － NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type, NR10050 Type : Measuring equipment : Impedance analyzer/material analyzer（HP4291A or equivalent HP4191A, 4192A or equivalent） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 7. Temperature characteristic NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Inductance change : Within ±20% NR10050 Type NS101, NS125 Type Inductance change : Within ±15% NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type : Measurement of inductance shall be taken at temperature range within －25℃～＋85℃. With reference to inductance value at ＋20℃., change rate shall be calculated. Test Methods and Remarks NS101, NS125 Type : Measurement of inductance shall be taken at temperature range within －40℃～＋125℃. With reference to inductance value at ＋20℃., change rate shall be calculated. Change of maximum inductance deviation in step 1 to 5 Step Temperature（℃） 1 20 2 Minimum operating temperature 3 20 (Standard temperature) 4 Maximum operating temperature 5 20 8. Resistance to flexure of substrate Specified Value NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type No damage NR10050 Type － NS101, NS125 Type No damage NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. As illustrated below, apply force in the direction of the arrow indicating until deflection of the test board reaches to 2 mm. Test board size : 100×40×1.0 Test board material : Glass epoxy-resin Solder cream thickness : 0.10mm (NR30, NRS20, NRH24/30, NRV20/30) : 0.15mm(NR40/50/60/80, NRS40/50/60, NS101/125Type) Test Methods and Remarks Land dimension C A B A Type NRS20, NRV20 NRH24 NR30, NRV30, NRH30 NR40, NRS40 NR50, NRS50 NR60, NRS60 NR80, NRS80 A 0.65 0.7 0.8 1.2 1.5 1.6 1.8 B 0.7 0.75 1.4 1.6 2.1 3.1 3.8 C 2.0 2.0 2.7 3.7 4.0 5.7 7.5 Type NS101 NS125 A 2.5 2.5 B 5.6 8.6 C 3.2 3.2 9. Insulation resistance : between wires NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type － NS101, NS125 Type 10. Insulation resistance : between wire and core NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type － NS101, NS125 Type ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 11. Withstanding voltage : between wire and core NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value － NR10050 Type NS101, NS125 Type 12. Adhesion of terminal electrode NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value Shall not come off PC board NR10050 Type NS101, NS125 Type NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. Applied force : 10N to X and Y directions. Duration : 5s. Solder cream thickness : 0.10mm (NR30, NRS20, NRH24/30, NRV20/30) : 0.15mm (NR40/50/60/80, NRS40/50/60, NS101/125Type) Test Methods and Remarks NR10050 Type Applied force Duration : 5N to X and Y directions. : 5s. 13. Resistance to vibration NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. Then it shall be submitted to below test conditions. Test Methods and Remarks Frequency Range Total Amplitude Sweeping Method Time 10～55Hz 1.5mm (May not exceed acceleration 196m/s2) 10Hz to 55Hz to 10Hz for 1min. X Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 14. Solderability NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type At least 90％ of surface of terminal electrode is covered by new solder. NS101, NS125 Type Test Methods and Remarks The test samples shall be dipped in flux, and then immersed in molten solder as shown in below table. Flux : Methanol solution containing rosin 25%. NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type Solder Temperature 245±5℃ Time 5±1.0 sec. ※Immersion depth : All sides of mounting terminal shall be immersed. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 15. Resistance to soldering heat NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test sample shall be exposed to reflow oven at 230±5℃ for 40 seconds, with peak temperature at 260±5℃ for 5 seconds, 2 times. Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80Type, NS101/125 Type Test board material : Glass epoxy-resin Test board thickness : 1.0mm NR10050 Type Test board material : Glass epoxy-resin Test board thickness : 1.6mm Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 16. Thermal shock NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. The test samples shall be placed at specified temperature for specified time by step 1 to step 4 as shown in below table in sequence. The temperature cycle shall be repeated 100 cycles. Conditions of 1 cycle Step Temperature (℃) Duration (min) 1 －40±3 30±3 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 17. Damp heat Specified Value Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10% No significant abnormality in appearance. NR10050 Type － NS101, NS125 Type Inductance change : Within ±10% No significant abnormality in appearance. NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. The test samples shall be placed in thermostatic oven set at specified temperature and humidity as shown in below table. Temperature 60±2℃ Humidity 90～95%RH Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 18. Loading under damp heat NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. The test samples shall be placed in thermostatic oven set at specified temperature and humidity and applied the rated current continuously as shown in below table. Temperature 60±2℃ Humidity 90～95％RH Applied current Rated current Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 19. Low temperature life test NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type Inductance change : Within ±10% No significant abnormality in appearance. NS101, NS125 Type Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type : The test samples shall be soldered to the test board by the reflow. After that, the test samples shall be placed at test conditions as shown in below table. Temperature －40±2℃ Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 20. High temperature life test Specified Value Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type － NR10050 Type － NS101, NS125 Type － NR10050 Type : Temperature 105±3℃ Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 21. Loading at high temperature life test Specified Value Test Methods and Remarks NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10% No significant abnormality in appearance. NR10050 Type － NS101, NS125 Type Inductance change : Within ±10% No significant abnormality in appearance. NR30/40/50/60/80, NRV30, NRH24/30, NRS40/50/60/80 Type, NS12555, NS12565, NS12575 Type : The test samples shall be soldered to the test board by the reflow soldering. Temperature 85±2℃ Applied current Rated current Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 22. Standard condition NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type Specified Value NR10050 Type NS101, NS125 Type Standard test condition : Unless otherwise specified, temperature is 20±15℃ and 65±20％of relative humidity. When there is any question concerning measurement result: In order to provide correlation data, the test shall be condition of 20±2℃ of temperature, 65±5% relative humidity. Inductance is in accordance with our measured value. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_smd_NR_NS_reli_e-E04R01 SMD POWER INDUCTORS（NR□, NS SERIES） ■PRECAUTIONS 1. Circuit Design Precautions ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Precautions ◆Land pattern design 1. Please refer to a recommended land pattern. 2. There is stress, which has been caused by distortion of a PCB, to the inductor. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) 3. Please consider the arrangement of parts on a PCB. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) ◆Land pattern design Surface Mounting 1. Mounting and soldering conditions should be checked beforehand. 2. Applicable soldering process to this products is reflow soldering only. 3. Please use the recommended land pattern shown as below. Electrical characteristics and the mounting ability of the product are being considered in the recommended land pattern. If a PCB is designed with other dimensions, defective soldering and stress to a product may occur due to misalignment. The performance of the product may not be brought out. If an adopted land pattern is different from the recommended land pattern, stress to the product will increase. It may cause cracks or defective electrical characteristics of the product. Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) 4. As coefficients of thermal expansion between an inductor and a PCB differs, cracks may occur on a ferrite core when thermal stress is applied to them after mounting an inductor. (Please refer to the drawings below.) Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) Clack on ferrite core Technical considerations Solder, electrode PCB 5. SMD inductors should be located to minimize any possible mechanical stresses from board warp or deflection. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection or twisting to the board. （NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type） A product tends to undergo stress in order “A>C>B≡D”. Please consider the layouts of a product to minimize any stresses. Electrode A Perforation Slit D B C ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) i_smd_NR_NS_prec_e-E06R01 3. Considerations for automatic placement Precautions ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. ◆Adjustment of mounting machine 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 2. Stress may be applied to a product with a warp or a twist in handling of the product. Please conduct validation completely before studying adoption of this product and please judge the pros and cons of adoption of this product with taking on responsibility. (NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/30/40/50/60/80 Type) Technical considerations ＜Wrap＞ ＜Twist＞ 4. Soldering Precautions ◆Reflow soldering 1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified. 2. The product shall be used reflow soldering only. 3. Please do not add any stress to a product until it returns in normal temperature after reflow soldering. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. ◆Recommended conditions for using a soldering iron (NR10050 Type) ・ Put the soldering iron on the land-pattern. ・ Soldering iron's temperature - Below 350℃ ・ Duration - 3 seconds or less ・ The soldering iron should not directly touch the inductor. ◆Reflow soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. ・NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type Recommended reflow condition (Pb free solder) Technical considerations 5. Cleaning Precautions Technical considerations ◆Cleaning conditions 1. Washing by supersonic waves shall be avoided. ◆Cleaning conditions 1. If washed by supersonic waves, the products might be broken. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) i_smd_NR_NS_prec_e-E06R01 6. Handling Precautions Technical considerations ◆Handling 1. Keep the product away from all magnets and magnetic objects. ◆Breakaway PC boards (splitting along perforations) 1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1. Please do not give the product any excessive mechanical shocks. 2. Please do not add any shock and power to a product in transportation. ◆Pick-up pressure 1. Please do not push to add any pressure to a winding part. Please do not give any shock and push into a ferrite core exposure part. ◆Packing 1. Please avoid accumulation of a packing box as much as possible. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Breakaway PC boards (splitting along perforations) 1. The position of the product on PCBs shall be carefully considered to minimize the stress caused from splitting of the PCBs. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 2. There is a case to be broken by the handling in transportation. ◆Pick-up pressure 1. Damage and a characteristic can vary with an excessive shock or stress. ◆Packing 1. If packing boxes are accumulated, that could cause a deformation on packing tapes or a damage on the products. 7. Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : －5～40℃ Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) i_smd_NR_NS_prec_e-E06R01 for General Electronic Equipment 绕线型片状功率电感器（BR 系列） 绕线型片状功率电感器（BR 系列） ■型号标示法 B R ① *使用温度范围：-40～+105℃（包含产品本身发热） △ L ② 2 5 1 ③ T ④ 2 R 2 ⑤ M △ △ △ ⑥ ⑦ ④包装 代码 T 类型 绕线型片状功率电感器 ⑤标称电感值 代码（例） R20 1R0 100 101 ※R＝小数点 特性 超薄 大电流 ③尺寸（L×W） 代码 1608 2012 2016 2518 3225 外型（inch） 1608（0603） 2012（0805） 2016（0806） 2518（1007） 3225（1210） 包装 卷盘带装 标称电感值［μH］ 0.2 1.0 10 100 ⑥电感量公差 代码 K M 尺寸（L×W）［mm］ 1.6×0.8 2.0×1.25 2.0×1.6 2.5×1.8 3.2×2.5 功率电感器 ②特性 代码 FL △L HL △C △＝空格 电感器 ①类型 代码 BR 8 电感量公差 ±10％ ±20％ ⑦本公司管理记号 ■标准外型尺寸／标准数量 L 推荐焊盘图案 実装上的注意 ・请确认実装状态后使用。 ・本产品焊法限定为回流焊法。 W T Type 1608 2012 2016 2518 3225 C e Type BR L1608 BR C1608 BR L2012 BR C2012 BR C2016 BRFL2518 BR L2518 BRHL2518 BR C2518 BR L3225 A B A A 0.55 0.60 0.60 0.60 0.85 B 0.70 1.00 1.00 1.50 1.70 C 1.00 1.45 1.80 2.00 2.70 单位：mm 标准数量［pcs］ L W T e 1.6±0.2 （0.063±0.008） 1.6±0.2 （0.063±0.008） 2.0±0.2 （0.079±0.008） 2.0±0.2 （0.079±0.008） 2.0±0.2 （0.079±0.008） 2.5±0.2 （0.098±0.008） 2.5±0.2 （0.098±0.008） 2.5±0.2 （0.098±0.008） 2.5±0.2 （0.098±0.008） 3.2±0.2 （0.126±0.008） 0.8±0.2 （0.031±0.008） 0.8±0.2 （0.031±0.008） 1.25±0.2 （0.049±0.008） 1.25±0.2 （0.049±0.008） 1.6±0.2 （0.063±0.008） 1.8±0.2 （0.071±0.008） 1.8±0.2 （0.071±0.008） 1.8±0.2 （0.071±0.008） 1.8±0.2 （0.071±0.008） 2.5±0.2 （0.098±0.008） 0.7 max （0.028 max） 0.8±0.2 （0.031±0.008） 1.0 max （0.040 max） 1.4 max （0.056 max） 1.6±0.2 （0.063±0.008） 1.0 max （0.040 max） 1.2 max （0.048 max） 1.5 max （0.060 max） 1.8±0.2 （0.071±0.008） 1.7 max （0.068 max） 0.45±0.15 （0.016±0.006） 0.45±0.15 （0.016±0.006） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.75±0.2 （0.03±0.008） 纸带 压模带 － 3000 － 3000 － 3000 － 2000 － 2000 － 3000 － 3000 － 2000 － 2000 － 2000 单位：mm（inch） i_wound_BR_j-E08R01-c.doc ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 67 for General Electronic Equipment ■型号一览 ●1608（0603）型 型号 BR L1608T1R0M BR L1608T1R5M BR L1608T2R2M BR L1608T3R3M BR L1608T4R7M BR L1608T6R8M BR L1608T100M BR L1608T150M 电感器 型号 功率电感器 BR C1608TR43M BR C1608TR50M BR C1608TR60M BR C1608TR72M BR C1608TR82M BR C1608T1R0M 6 6 6 6 6 6 型号 BR C1608TR20M BR C1608TR35M BR C1608TR45M BR C1608TR56M BR C1608TR77M BR C1608T1R0M BR C1608T1R5M BR C1608T2R2M EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 700 600 400 300 150 100 45 32 0.230 0.280 0.400 0.650 1.00 1.64 2.00 2.56 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS 0.43 0.50 0.60 0.72 0.82 1.0 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 740 710 630 600 560 550 0.082 0.090 0.099 0.144 0.176 0.188 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.20 0.35 0.45 0.56 0.77 1.0 1.5 2.2 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 400 300 200 170 150 140 120 100 0.060 0.080 0.090 0.095 0.110 0.180 0.300 0.550 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS 0.47 1.0 2.2 ±20％ ±20％ ±20％ 500 400 250 0.048 0.108 0.184 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 0.47 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 350 300 250 200 190 150 60 30 15 13 8.0 7.0 6.5 6.0 0.090 0.135 0.180 0.300 0.500 0.550 0.750 0.850 1.00 1.30 2.00 3.50 5.80 7.70 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 ±20％ ±20％ ±20％ ±20％ ±20％ 490 390 350 300 250 0.060 0.090 0.110 0.170 0.265 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 510 440 360 290 240 200 170 150 650 590 500 390 310 250 220 200 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 1,400 1,200 1,100 1,000 950 890 1,100 1,050 940 810 730 680 测试频率 ［MHz］ 6.0 6.0 6.0 6.0 6.0 6.0 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 1,750 1,400 1,250 1,150 1,000 850 700 550 测试频率 ［MHz］ 980 810 800 760 660 520 410 280 测试频率 ［MHz］ 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 ●2012（0805）型 型号 BR L2012TR47M 6 BR L2012T1R0M 6 BR L2012T2R2MD6 型号 BR L2012TR47M BR L2012T1R0M BR L2012T1R5M BR L2012T2R2M BR L2012T3R3M BR L2012T4R7M BR L2012T6R8M BR L2012T100M BR L2012T150M BR L2012T220M BR L2012T330M BR L2012T470M BR L2012T680M BR L2012T101M 型号 BR BR BR BR BR C2012T1R0M C2012T1R5MD C2012T2R2MD C2012T3R3MD C2012T4R7MD 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 1,500 1,050 680 1,900 1,230 950 6.0 6.0 6.0 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 1,100 850 700 600 490 340 290 270 220 190 150 125 100 85 1,050 850 750 550 440 400 350 330 300 270 220 160 110 85 1,400 1,100 1,000 870 600 测试频率 ［MHz］ 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 1,500 1,200 1,100 800 700 测试频率 ［MHz］ 测试频率 ［MHz］ 1.0 1.0 1.0 1.0 1.0 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为Idc1或 Idc2中较低的直流电流值。 i_wound_BR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 68 21 for General Electronic Equipment ■型号一览 ●2016（0806）型 型号 C2016T1R0M C2016T1R5M C2016T2R2M C2016T3R3M C2016T4R7M C2016T6R8M C2016T100[] C2016T150[] C2016T220[] C2016T330[] C2016T470[] C2016T680[] C2016T101[] 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 450 370 250 140 78 39 35 28 24 13 11 8 7 0.085 0.150 0.180 0.220 0.270 0.330 0.400 0.600 1.00 1.70 2.20 2.80 3.40 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 ±20％ ±20％ ±20％ ±20％ ±20％ 130 100 80 70 60 0.090 0.110 0.130 0.220 0.330 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 ±20％ ±20％ ±20％ ±20％ ±20％ 130 100 80 70 60 0.080 0.100 0.135 0.300 0.400 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 ±20％ ±20％ ±20％ ±20％ ±20％ 400 350 300 200 150 0.055 0.085 0.115 0.165 0.245 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 280 230 200 150 100 45 20 13 10 8 6.5 5.5 4.5 0.050 0.080 0.120 0.175 0.230 0.280 0.350 0.430 0.560 0.850 1.45 2.40 3.60 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 1,350 1,100 910 740 660 550 450 400 310 270 210 200 140 1,100 820 760 680 610 560 520 410 310 240 210 190 170 测试频率 ［MHz］ 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 电感器 BR BR BR BR BR BR BR BR BR BR BR BR BR EHS ●2518（1007）型 型号 型号 BR BR BR BR BR L2518T1R0M L2518T1R5M L2518T2R2M L2518T3R3M L2518T4R7M 型号 BRHL2518T1R0M BRHL2518T1R5M BRHL2518T2R2M BRHL2518T3R3MD BRHL2518T4R7MD 型号 BR C2518T1R0M RoHS BR C2518T1R5M RoHS BR C2518T2R2M RoHS BR C2518T3R3M RoHS BR C2518T4R7M RoHS BR C2518T6R8M RoHS BR C2518T100[] RoHS BR C2518T150[] RoHS BR C2518T220[] RoHS BR C2518T330[] RoHS BR C2518T470[] RoHS BR C2518T680[] RoHS BR C2518T101[] RoHS (注)型号中的 []中标有电感值代码（M或K）。 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 1,200 1,100 850 700 650 1,200 1,000 950 700 650 1.0 1.0 1.0 1.0 1.0 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 1,600 1,200 1,000 800 700 1,000 920 850 580 470 1,400 1,100 1,000 800 750 1,650 1,300 1,000 860 750 680 610 550 490 390 300 230 190 测试频率 ［MHz］ 1.0 1.0 1.0 1.0 1.0 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 2,550 2,100 1,800 1,450 1,250 1,050 890 760 640 560 410 340 300 测试频率 ［MHz］ 7.96 7.96 7.96 7.96 7.96 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 2,000 1,700 1,500 1,200 1,100 测试频率 ［MHz］ 功率电感器 BRFL2518T1R0M BRFL2518T1R5M BRFL2518T2R2M BRFL2518T3R3M BRFL2518T4R7M 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 测试频率 ［MHz］ 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为Idc1或 Idc2中较低的直流电流值。 i_wound_BR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 69 for General Electronic Equipment ■型号一览 ●3225（1210）型 型号 BR L3225TR27M BR L3225TR36M BR L3225TR51M 型号 电感器 功率电感器 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS 0.27 0.36 0.51 ±20％ ±20％ ±20％ 390 350 270 0.022 0.025 0.029 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±20％） ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 220 170 150 140 120 90 70 20 13 9 7 6 5 0.043 0.045 0.065 0.120 0.180 0.270 0.350 0.570 0.690 0.840 1.00 1.40 2.50 BR L3225T1R0M RoHS BR L3225T1R5M RoHS BR L3225T2R2M RoHS BR L3225T3R3M RoHS BR L3225T4R7M RoHS BR L3225T6R8M RoHS BR L3225T100[] RoHS BR L3225T150[] RoHS BR L3225T220[] RoHS BR L3225T330[] RoHS BR L3225T470[] RoHS BR L3225T680[] RoHS BR L3225T101[] RoHS (注)型号中的 []中标有电感值代码（M或K）。 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 4,500 4,300 3,600 2,850 2,750 2,550 7.96 7.96 7.96 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 2,400 2,200 1,850 1,450 1,300 1,050 900 700 550 470 420 330 270 2,200 1,750 1,600 1,200 1,000 770 700 530 470 420 390 300 250 测试频率 ［MHz］ 测试频率 ［MHz］ 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为Idc1或 Idc2中较低的直流电流值。 i_wound_BR_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 70 21 WIRE-WOUND CHIP POWER INDUCTORS（BR SERIES） ■PACKAGING ①Minimum Quantity Standard Quantity [pcs] Paper Tape Embossed Tape － 3,000 － 3,000 － 3,000 － 2,000 － 2,000 － 2,000 － 2,000 － 3,000 － 3,000 － 2,000 Type BR C1608 BR L1608 BR L2012 BR C2012 BR C2016 BR C2518 BRHL2518 BR L2518 BRFL2518 BR L3225 ②Tape Material ●Embossed tape Top tape Sprocket hole Base tape Chip cavity Chip Filled Chip ③Taping dimensions ●Embossed Tape 8mm wide (0.315 inches wide) A B F 1.75±0.1 (0.069±0.004） 8.0±0.2 (0.315±0.008) φ1.5＋0.1/－0 (φ0.059＋0.004/-0) 3.5±0.05 (0.138±0.002) Sprocket hole 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_pack_e-E05R01 Type BR L1608 BR C1608 BR L2012 BR C2012 BR C2016 BRFL2518 BR L2518 BRHL2518 BR C2518 BR L3225 Chip cavity A B 1.1±0.1 1.9±0.1 (0.043±0.004) (0.075±0.004) 1.1±0.1 1.9±0.1 (0.043±0.004) (0.075±0.004) 1.45±0.1 2.2±0.1 (0.057±0.004) (0.087±0.004) 1.45±0.1 2.37±0.1 (0.057±0.004) (0.093±0.004) 1.75±0.1 2.1±0.1 (0.069±0.004) (0.083±0.004) 2.3±0.1 2.8±0.1 (0.091±0.004) (0.110±0.004) 2.3±0.1 2.8±0.1 (0.091±0.004) (0.110±0.004) 2.1±0.1 2.8±0.1 (0.083±0.004) (0.110±0.004) 2.15±0.1 2.7±0.1 (0.085±0.004) (0.106±0.004) 2.8±0.1 3.5±0.1 (0.110±0.004) (0.138±0.004) Insertion pitch F 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) 4.0±0.1 (0.157±0.004) Tape thickness T K 0.2±0.05 0.9 max (0.008±0.002) (0.035 max) 0.25±0.05 1.2 max (0.010±0.002) (0.047 max) 0.25±0.05 1.2 max (0.010±0.002) (0.047 max) 0.25±0.05 1.59 max (0.010±0.002) (0.063 max) 0.3±0.05 1.9 max (0.012±0.002) (0.075 max) 0.25±0.05 1.3 max (0.010±0.002) (0.051 max) 0.3±0.05 1.45 max (0.012±0.002) (0.057 max) 0.3±0.05 1.7 max (0.012±0.002) (0.067 max) 0.3±0.05 2.2 max (0.012±0.002) (0.087 max) 0.25±0.05 1.9 max (0.010±0.002) (0.075 max) Unit：mm（inch） ④Leader and Blank portion ⑤Reel size ⑥Top Tape Strength The top tape requires a peel-off force of 0.2 to 0.7N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_pack_e-E05R01 WIRE-WOUND CHIP POWER INDUCTORS（BR SERIES） ■RELIABILITY DATA 1. Operating Temperature Range Specified Value BR series Test Methods and Remarks Including self-generated heat －40～＋105℃ 2. Storage Temperature Range（after soldering） Specified Value BR series Test Methods and Remarks －40～＋85℃ Please refer the term of "7.Storage conditions" in Precautions. 3. Rated current Specified Value BR series Within the specified tolerance 4. Inductance Specified Value BR series Test Methods and Remarks Measuring equipment Measuring frequency Within the specified tolerance : LCR Meter （HP 4285A or equivalent） : Specified frequency 5. DC Resistance Specified Value BR series Test Methods and Remarks Measuring equipment Within the specified tolerance : DC ohmmeter （HIOKI 3227 or equivalent） 6. Self resonance frequency Specified Value BR series Test Methods and Remarks Measuring equipment Within the specified tolerance : Impedance analyzer/material analyzer （HP4291A or equivalent HP4191A, 4192A or equivalent） 7. Temperature characteristic Specified Value BR series Test Methods and Remarks Inductance change : Within ±15% Based on the inductance at 20℃ and Measured at the ambient of －40℃～＋85℃. 8. Resistance to the bendability Specified Value BR series Test Methods and Remarks The given sample is soldered on the board and then the back side of the board is pushed until it bends 2mm like the figure. Dimension of the board : 100×40×1.0mm (0.8mm thickness for 1608(0603) inductors) Material of the board : Glass epoxy-resin Thickness of soldering paste : 0.12mm No damage. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_reli_e-E05R01 9. Body strength Specified Value BR series Test Methods and Remarks 2012～ Applied orce Duration 1608 size Applied force Duration No damage. 10N : 10sec. : 5N : 10sec. 10. Adhesion of terminal electrodes Specified Value BR series Test Methods and Remarks The given sample is soldered to the board and then it is kept for 5sec with 10N stress (5N for 1608(0603) inductors) like the figure. Not to removed from the board. 11. Resistance to vibration Inductance change : Within ±10% No significant abnormality in appearance. Specified Value BR series Test Methods and Remarks The given sample is soldered to the board and then it is tested depending on the conditions of the following table. Vibration Frequency 10～55Hz Total Amplitude 1.5mm (May not exceed acceleration 196m/s2) Sweeping Method 10Hz to 55Hz to 10Hz for 1min. X Time Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 12. Solderability Specified Value BR series Test Methods and Remarks Test Method and Remarks】 The given sample is dipped into the flux and then it is tested depending on the conditions of the following table. Flux : Methanol solution containing rosin 25%. Solder Temperature 245±5℃ Time 5±0.5 sec. At least 90% area of the electrodes is covered by new solder. 13. Resistance to soldering heat Inductance change : Within ±10% No significant abnormality in appearance. Specified Value BR series Test Methods and Remarks 3 times reflow having the temperature profile of 5sec of 260＋0/－5 ℃ and 40sec of more than 230℃. Test board thickness : 1.0mm Test board material : Glass epoxy-resin Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 14. Thermal shock Specified Value Test Methods and Remarks BR series Inductance change : Within ±10% No significant abnormality in appearance. The given sample is soldered to the board and then its Inductance is measured after 100cycles of the following conditions. Conditions of 1 cycle Step Temperature (℃) Duration (min) 1 －40±3 30±3 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_reli_e-E05R01 15. Damp heat Inductance change : Within ±10% No significant abnormality in appearance. Specified Value BR series Test Methods and Remarks The given sample is soldered to the board and then it is kept at the following conditions. Temperature 60±2℃ Humidity 90～95%RH Time 1000 hours. Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 16. Loading under damp heat Inductance change : Within ±10% No significant abnormality in appearance. Specified Value BR series Test Methods and Remarks The given sample is soldered to the board and then it is kept at the following conditions. Temperature 60±2℃ Humidity 90～95％RH Applied current Rated current Time 1000hours. Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 17. Low temperature life test Inductance change : Within ±10% No significant abnormality in appearance. Specified Value BR series Test Methods and Remarks The given sample is soldered to the board and then it is kept at the following conditions. Temperature －40±2℃ Duration 1000hours Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 18. High temperature life test Inductance change : Within ±10% No significant abnormality in appearance. Specified Value BR series Test Methods and Remarks The given sample is soldered to the board and then it is kept at the following conditions. Temperature 85±2℃ Duration 1000hours Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 19. Standard conditions Specified Value BR series Standard test condition : Unless otherwise specified, temperature is 20±15℃ and 65±20％of relative humidity. When there is any question concerning measurement result: In order to provide correlation data, the test shall be condition of 20±2℃ of temperature, 65±5% relative humidity. Inductance is in accordance with our measured value. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_reli_e-E05R01 WIRE-WOUND CHIP POWER INDUCTORS（BR SERIES） ■PRECAUTIONS 1. Circuit Design Precautions ◆Operating Ambient The products are premised on the usage for the general equipments like the office supply equipment, the telecommunications systems, the measuring equipment, the household equipment and so on. Please ask to TAIYO YUDEN's sales person in advance, if you need to apply them to the equipments or the systems which might have any influences for the human body, the property, like the traffic systems, the safety equipment, the aerospace systems, the nuclear control systems, the medical equipment and soon. 2. PCB Design Precautions Technical considerations ◆Land pattern design 1. Please refer to a recommended land pattern. ◆Land pattern design Surface Mounting 1. The conditions of the picking and placing should be checked in advance. 2. The products are only for reflow soldering. 3. Considerations for automatic placement Precautions Technical considerations ◆Adjustment of mounting machine 1. Excessive physical impact should not be imposed on the products for picking and placing onto the PC boards. 2. Mounting and soldering conditions should be checked in advance. ◆Adjustment of mounting machine The products might be broken if too much stress is given for the picking and placing. 4. Soldering Precautions ◆Reflow soldering 1. Please apply our recommended soldering conditions on the specification as much as possible. 2. The products are only for reflow soldering. 3. Please do not give any stress to a product until it returns in room temperature after reflow soldering. ◆Recommended conditions for using a soldering iron. （Excluding 1608 type） Touch a soldering iron to the land pattern not to the product directly. The temperature of a soldering iron is less than 350degC. The soldering is for 3 seconds or less. ◆Reflow soldering 1. The product might break or might make the tombstoning, if the soldering conditions are too far from our recommended conditions. Technical considerations 5. Cleaning Precautions Technical considerations ◆Cleaning conditions 1. Please don't wash by the ultra-sonic waves. ◆Cleaning conditions 1. Washing by the ultra-sonic waves might break the product. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_prec_e-E06R01 6. Handling Precautions Technical considerations ◆Handling 1. Keep the product away from any magnets. ◆Cutting the PC boards 1. Please don't give any stress of the bending or the twisting for the cutting process of PC boards. 2. Please don't give any shock and stress to the products in transportation. ◆Mechanical considerations 1. Please don't give too much shock to the product. 2. Please don't give any shock and stress to the products in transportation. ◆The stress for picking and placing 1. Please don't give any shock into an exposed ferrite core. ◆Packing 1. Please don't pile the packing boxes up as much as possible. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Cutting the PC boards 1. Please don't give the bending stress or the twisting stress to the products because they might break in such cases. ◆Mechanical considerations 1. The mechanical shock might break the products. 2. The products might break depending on the handling in transportation. ◆Pick-up pressure 1. The electrical characteristics of the products might be shifted by too much physical shock and stress. ◆Packing 1. The products and the tape might break, if the packing boxes are piled up. 7. Storage conditions Precautions Technical considerations ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : 0～40℃ Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. ◆Storage 1. The ambient of high temperature or high humidity might accelerate to make the solderability and the tape worse. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_BR_prec_e-E06R01 for General Electronic Equipment 绕线型片状功率电感器（CB 系列） 绕线型片状功率电感器（CB 系列） *使用温度范围：-40～+105℃（包含产品本身发热） ■型号标示法 C B △ △ ② ① 2 0 1 2 T ④ ③ 1 ②特性 代码 △△ △C △L MF 特性 标准品 大电流 超薄 低损耗 ③尺寸（L×W） 代码 1608 2012 2016 2518 3225 外型（inch） 1608（0603） 2012（0805） 2016（0806） 2518（1007） 3225（1210） △＝空格 ④包装 代码 T 包装 卷盘带装 ⑤标称电感值 代码（例） 1R0 100 101 ※R＝小数点 标称电感值［μH］ 1.0 10 100 ⑥电感量公差 代码 K M 尺寸（L×W）［mm］ 1.6×0.8 2.0×1.25 2.0×1.6 2.5×1.8 3.2×2.5 功率电感器 类型 绕线型片状功率电感器 M △ △ △ △ ⑥ ⑦ ⑧ 电感器 ①类型 代码 CB 0 0 ⑤ 电感量公差 ±10％ ±20％ ⑦个别规格 代码 △ R 个别规格 标准品 低 Rdc 品 ⑧本公司管理记号 ■标准外型尺寸／标准数量 CB／CB C／CB L 推荐焊盘图案 実装上的注意 ・请确认実装状态后使用。 ・本产品焊法限定为回流焊法。 CBMF W W L L T T e C e A Type CBMF1608 CB L2012 CB 2012 CB C2012 CB 2016 CB C2016 CB 2518 CB C2518 CB C3225 Type MF1608 2012 2016 2518 3225 B A A 0.55 0.60 0.60 0.60 0.85 B 0.7 1.0 1.0 1.5 1.7 C 1.0 1.45 1.8 2.0 2.7 单位：mm 标准数量［pcs］ L W T e 1.6±0.2 （0.063±0.008） 2.0±0.2 （0.079±0.008） 2.0±0.2 （0.079±0.008） 2.0±0.2 （0.079±0.008） 2.5±0.2 （0.098±0.008） 3.2±0.2 （0.126±0.008） 0.8±0.2 （0.031±0.008） 1.25±0.2 （0.049±0.008） 1.25±0.2 （0.049±0.008） 1.6±0.2 （0.063±0.008） 1.8±0.2 （0.071±0.008） 2.5±0.2 （0.098±0.008） 0.8±0.2 （0.031±0.008） 0.9±0.1 （0.035±0.004） 1.25±0.2 （0.049±0.008） 1.6±0.2 （0.063±0.008） 1.8±0.2 （0.071±0.008） 2.5±0.2 （0.098±0.008） 0.45±0.15 （0.016±0.006） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.5±0.2 （0.020±0.008） 0.6±0.3 （0.024±0.012） 纸带 压模带 － 3000 4000 － － 3000 － 2000 － 2000 － 1000 单位：mm（inch） i_wound_CB_j-E08R01-c.doc ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 71 for General Electronic Equipment ■型号一览 ●1608（0603）型 型号 CBMF1608T1R0M CBMF1608T2R2M CBMF1608T3R3M CBMF1608T4R7M CBMF1608T100[] CBMF1608T220[] CBMF1608T470[] EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 2.2 3.3 4.7 10 22 47 ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 100 80 60 45 32 16 11 0.09 0.17 0.22 0.24 0.36 1.0 2.5 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 2.2 3.3 4.7 6.8 10 10 15 22 47 68 100 ±20％ ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 100 80 55 45 38 32 32 28 16 11 10 8 0.15 0.23 0.30 0.40 0.47 0.70 0.50 1.3 1.7 3.7 6.0 7.0 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS 1.0 2.2 4.7 10 22 47 ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 100 70 45 40 16 11 0.19 0.33 0.50 1.2 3.7 5.8 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS 1.0 2.2 4.7 10 22 47 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ 100 80 45 32 23 11 0.15 0.39 0.66 1.0 2.1 4.2 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 100 80 70 55 45 38 32 28 16 14 11 10 8 0.09 0.11 0.13 0.20 0.25 0.35 0.50 0.70 1.0 1.7 2.4 3.0 4.5 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 290 190 170 145 115 70 50 770 560 500 470 380 230 140 测试频率 ［MHz］ 7.96 7.96 7.96 7.96 2.52 2.52 2.52 ●2012（0805）型 电感器 型号 功率电感器 CB CB CB CB CB CB CB CB CB CB CB CB 2012T1R0M 2012T2R2M 2012T3R3M 2012T4R7M 2012T6R8M 2012T100[] 2012T100[]R 2012T150[] 2012T220[] 2012T470[] 2012T680[] 2012T101[] 型号 CB CB CB CB CB CB C2012T1R0M C2012T2R2M C2012T4R7M C2012T100[] C2012T220[] C2012T470[] 型号 CB CB CB CB CB CB L2012T1R0M L2012T2R2M L2012T4R7M L2012T100M L2012T220M L2012T470M 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 500 410 330 300 250 190 200 170 135 90 70 60 900 770 650 580 540 440 520 320 280 190 140 130 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 700 530 360 240 170 120 840 640 520 340 190 150 测试频率 ［MHz］ 7.96 7.96 7.96 2.52 2.52 2.52 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 620 440 275 205 150 100 测试频率 ［MHz］ 950 590 490 370 250 140 测试频率 ［MHz］ 0.1 0.1 0.1 0.1 0.1 0.1 ●2016（0806）型 型号 CB 2016T1R0M RoHS CB 2016T1R5M RoHS CB 2016T2R2M RoHS CB 2016T3R3M RoHS CB 2016T4R7M RoHS CB 2016T6R8M RoHS CB 2016T100[] RoHS CB 2016T150[] RoHS CB 2016T220[] RoHS CB 2016T330[] RoHS CB 2016T470[] RoHS CB 2016T680[] RoHS CB 2016T101[] RoHS (注)型号中的 []中标有电感值代码（M或K）。 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 600 550 510 400 340 300 250 210 165 130 110 90 70 1,100 1,000 1,000 800 740 600 520 440 370 270 240 210 170 测试频率 ［MHz］ 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为Idc1或 Idc2中较低的直流电流值。 i_wound_CB_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 72 21 for General Electronic Equipment ■型号一览 型号 C2016T1R0M C2016T1R5M C2016T2R2M C2016T3R3M C2016T4R7M C2016T6R8M C2016T100[] C2016T150[] C2016T220[] C2016T330[] C2016T470[] C2016T680[] C2016T101[] 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 100 80 70 55 45 38 32 28 16 14 11 10 8 0.10 0.15 0.20 0.27 0.37 0.59 0.82 1.2 1.8 2.8 4.3 7.0 8.0 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 1.0 1.5 2.2 3.3 4.7 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1000 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 100 80 68 54 46 46 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 3.5 3.0 2.4 0.06 0.07 0.09 0.11 0.10 0.13 0.15 0.25 0.32 0.50 0.70 0.95 1.5 2.1 3.2 4.5 7.0 10 17 24 EHS 标称电感值 ［μH］ 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 100 80 68 54 41 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 3.5 3.0 0.08 0.11 0.13 0.16 0.20 0.30 0.36 0.65 0.77 1.5 1.9 2.8 3.7 6.1 8.4 12.3 22 28 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 1,100 1,000 750 600 550 450 380 300 250 220 150 130 110 1,100 1,000 720 610 530 450 350 300 240 220 150 130 110 测试频率 ［MHz］ 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 电感器 CB CB CB CB CB CB CB CB CB CB CB CB CB EHS ●2518（1007）型 型号 2518T1R0M 2518T1R5M 2518T2R2M 2518T3R3M 2518T4R7MR 2518T4R7M 2518T6R8M 2518T100[] 2518T150[] 2518T220[] 2518T330[] 2518T470[] 2518T680[] 2518T101[] 2518T151[] 2518T221[] 2518T331[] 2518T471[] 2518T681[] 2518T102[] 型号 CB C2518T1R0M RoHS CB C2518T1R5M RoHS CB C2518T2R2M RoHS CB C2518T3R3M RoHS CB C2518T4R7M RoHS CB C2518T6R8M RoHS CB C2518T100[] RoHS CB C2518T150[] RoHS CB C2518T220[] RoHS CB C2518T330[] RoHS CB C2518T470[] RoHS CB C2518T680[] RoHS CB C2518T101[] RoHS CB C2518T151[] RoHS CB C2518T221[] RoHS CB C2518T331[] RoHS CB C2518T471[] RoHS CB C2518T681[] RoHS (注)型号中的 []中标有电感值代码（M或K）。 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1,200 650 510 440 310 340 270 250 180 165 130 110 70 60 55 50 40 35 30 25 1,500 1,400 1,300 1,200 1,200 1,100 930 820 650 580 460 420 310 260 210 180 140 120 90 75 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.252 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 1,000 950 890 730 680 550 480 350 320 270 240 200 160 140 115 100 80 65 1,200 1,190 1,100 1,020 920 740 680 500 460 320 290 200 170 130 110 90 70 60 测试频率 ［MHz］ 功率电感器 CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 测试频率 ［MHz］ 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为Idc1或 Idc2中较低的直流电流值。 i_wound_CB_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 21 73 for General Electronic Equipment ■型号一览 ●3225（1210）型 型号 EHS 标称电感值 ［μH］ 电感器 CB C3225T1R0MR RoHS 1.0 CB C3225T1R5MR RoHS 1.5 CB C3225T2R2MR RoHS 2.2 CB C3225T3R3MR RoHS 3.3 CB C3225T4R7MR RoHS 4.7 CB C3225T6R8MR RoHS 6.8 CB C3225T100[]R RoHS 10 CB C3225T150[]R RoHS 15 CB C3225T220[]R RoHS 22 CB C3225T330[]R RoHS 33 CB C3225T470[]R RoHS 47 CB C3225T680[]R RoHS 68 CB C3225T101[]R RoHS 100 CB C3225T221[]R RoHS 220 CB C3225T821[]R RoHS 820 CB C3225T102[]R RoHS 1000 (注)型号中的 []中标有电感值代码（M或K）。 电感量公差 自共振频率 ［MHｚ］ （min.） 直流电阻 ［Ω］（±30％） ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ ±10％，±20％ 250 220 190 160 70 50 23 20 17 13 10 8.0 6.0 3.0 1.8 1.6 0.055 0.060 0.080 0.095 0.100 0.120 0.133 0.195 0.27 0.41 0.67 1.0 1.4 2.5 12 13 额定电流　※）　［ｍA］ 直流重叠允许电流 温度上升允许电流 Idc1 Idc2 2,000 2,000 2,000 2,000 1,250 950 900 730 620 500 390 320 270 190 110 100 1,440 1,310 1,130 1,040 1,010 940 900 850 780 570 480 410 340 190 110 100 测试频率 ［MHz］ 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 功率电感器 ※）直流重叠允许电流（Idc1）为直流电流重叠产生的电感值下降，范围在30％以内的直流电流值（at 20℃） ※）温度上升允许电流（Idc2）为温度上升至40℃时的直流电流值（at 20℃） ※）额定电流值为Idc1或 Idc2中较低的直流电流值。 i_wound_CB_j-E08R01-c2.xlsx ▶ 由于篇幅有限，本产品目录中只记载了有代表性的产品规格，若考虑使用敝公司产品时，请确认交货规格说明书中的详细规格。 另外，有关各产品的详细信息 （特性图、可靠性信息、使用时的注意事项等），请参阅敝公司网站 （http://www.ty-top.com/ ）。 74 21 WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PACKAGING ①Minimum Quantity Standard Quantity ［pcs］ Paper Tape Embossed Tape Type LB C3225 CB C3225 LB 3218 LB R2518 LB C2518 LB 2518 CB 2518 CB C2518 LBM2016 LB C2016 LB 2016 CB 2016 CB C2016 LB 2012 LB C2012 LB R2012 CB 2012 CB C2012 CB L2012 LB 1608 LBMF1608 CBMF1608 － 1000 － 2000 － 2000 － 2000 － 3000 4000 4000 － － － 3000 ②Tape material ●Embossed tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip ●Card board carrier tape Top tape Base tape Chip Filled Sprocket hole Bottom tape Chip cavity Chip ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01 ③Taping Dimensions ●Embossed Tape （0.315 inches wide） A B F Type LBM2016 LB C3225 CB C3225 LB 3218 LB 2518 CB 2518 LB C2518 CB C2518 LB R2518 LB 2016 CB 2016 LB C2016 CB C2016 LB 2012 CB 2012 LB C2012 CB C2012 LB R2012 LBMF1608 CBMF1608 1.75±0.1 (0.069±0.004） 8.0±0.3 (0.315±0.012) φ1.5＋0.1/－0 (φ0.059＋0.004/-0) 3.5±0.05 (0.138±0.002) Sprocket hole 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity A B 1.75±0.1 2.1±0.1 （0.069±0.004） （0.083±0.004） 2.8±0.1 3.5±0.1 （0.110±0.004） （0.138±0.004） 2.1±0.1 3.5±0.1 （0.083±0.004） （0.138±0.004） Insertion pitch F 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） Tape thickness T K 0.3±0.05 1.9max. （0.012±0.002） （0.075max.） 0.3±0.05 4.0max. （0.012±0.002） （0.157max.） 0.3±0.05 2.2max. （0.012±0.002） （0.087max.） 2.15±0.1 （0.085±0.004） 2.7±0.1 （0.106±0.004） 4.0±0.1 （0.157±0.004） 0.3±0.05 （0.012±0.002） 2.2max. （0.087max.） 1.75±0.1 （0.069±0.004） 2.1±0.1 （0.083±0.004） 4.0±0.1 （0.157±0.004） 0.3±0.05 （0.012±0.002） 1.9max. （0.075max.） 1.45±0.1 （0.057±0.004） 2.25±0.1 （0.089±0.004） 4.0±0.1 （0.157±0.004） 0.25±0.05 （0.010±0.002） 1.45max. （0.057max.） 1.1±0.1 （0.043±0.004） 1.9±0.1 （0.075±0.004） 4.0±0.1 （0.157±0.004） 0.25±0.05 （0.010±0.002） 1.2max. （0.047max.） Unit：mm（inch） Insertion pitch F 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） Tape thickness T 1.1max. （0.043max.） 1.1max. （0.043max.） Unit：mm（inch） ●Card board carrier tape（0.315 inches wide） A B F Type CB L2012 LB 1608 1.75±0.1 (0.069±0.004） T 8.0±0.3 (0.315±0.012) φ1.5＋0.1/－0 (φ0.059＋0.004/-0) 3.5±0.05 (0.138±0.002) Sprocket hole 4.0±0.1 (0.157±0.004) 2.0±0.1 (0.079±0.004) Chip cavity A B 1.55±0.1 2.3±0.1 （0.061±0.004） （0.091±0.004） 1.0±0.1 1.8±0.1 （0.039±0.004） （0.071±0.004） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01 ④Leader and Blank Portion ⑤Reel Size ⑥Top Tape Strength The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_pack_e-E05R01 WIRE-WOUND CHIP INDUCTORS (LB SERIES), WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES), WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■RELIABILITY DATA 1.Operating temperature Range LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series －40～＋105℃（Including self-generated heat） LBM Series 2. Storage Temperature Range（after soldering） LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series －40～＋85℃ LBM Series Test Methods and Remarks LB, CB Series： Please refer the term of "7. storage conditions" in precautions. 3.Rated Current LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series 4.Inductance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Remarks LB・LBC・LBR・CB・CBC・CBL・LBMF・CBMF・LBM Series Measuring equipment ：LCR Mater（HP4285A or its equivalent） Measuring frequency : Specified frequency 5.Q LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series Test Methods and Remarks LBM Series Measuring equipment Measuring frequency － Within the specified tolerance : LCR Mater（HP4285A or its equivalent） : Specified frequency 6.DC Resisitance LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Remarks Measuring equipment : DC Ohmmeter （HIOKI 3227 or its equivalent） 7.Self-Resonant Frequency LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Within the specified tolerance LBM Series Test Methods and Remarks Measuring equipment : Impedance analyzer （HP4291A or its equivalent） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01 8.Temperature Characteristic LBM2016 Specified Value Test Methods and Remarks Inductance change : Within±5％ LB1608 LB2012 LBR2012 CB2012 CBL2012 LB2016 CB2016 LB2518 LBR2518 CB2518 LBC3225 CBC3225 LBMF1608 CBMF1608 LBC2016 CBC2016 LBC2518 CBC2518 LB3218 LBC2012 CBC2012 Inductance change : Within±20％ Inductance change : Within±25％ Inductance change : Within±35％ Based on the inductance at 20℃ and Measured at the ambient of －40℃～＋85℃. 9.Rasistance to Flexure of Substrate LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series Warp : 2mm（LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Series） Test substrate : Glass epoxy-resin substrate Thickness : 0.8mm（LB1608・LBMF1608・CBMF1608） : 1.0mm（Others） Test Methods and Remarks 10.Body Strength LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No damage. LBM Series Test Methods and Remarks LB・LBC・LBR・CB・CBC・CBL・LBM Applied force : 10N Duration : 10sec. LB1608・LBMF1608・CBMF1608 Applied force : 5N Duration : 10sec. 11.Adhesion of terminal electrode LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series No abnormality. LBM Series Test Methods and Remarks LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Applied force : 10N to X and Y directions Duration : 5 sec. Test substrate : Printed board LB1608・CBMF1608・LBMF1608 Applied force : 5N to X and Y directions Duration : 5 sec. Test substrate : Printed board ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01 12.Resistance to vibration LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within±5％ No significant abnormality in appearance. LBM Series Test Methods and Remarks Inductance change : Within±10％ No significant abnormality in appearance. LB・LBR・LBC・CB・CBC・CBL・LBM・LBMF・CBMF： The given sample is soldered to the board and then it is tested depending on the conditions of the following table. Vibration Frequency 10～55Hz Total Amplitude 1.5mm (May not exceed acceleration 196m/s2) Sweeping Method 10Hz to 55Hz to 10Hz for 1min. X Time Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 13.Drop test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series － LBM Series 14.Solderability LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series At least 90％ of surface of terminal electrode is covered by new LBM Series Test Methods and Remarks LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Solder temperature : 245±5℃ Duration : 5±0.5sec Flux : Methanol solution with 25％ of colophony 15.Resistance to soldering LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series Test Methods and Remarks Inductance change : Within±10％ Inductance change : Within±5％ LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： 3 times of reflow oven at 230℃ MIN for 40sec. with peak temperature at 260 ℃ for 5sec. Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 16.Resisitance to solvent LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series － LBM Series Test Methods and Remarks Solvent temperature Type of solvent Cleaning conditions : Room temperature : Isopropyl alcohol : 90s. Immersion and cleaning. 17.Thermal shock LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within±10％ No significant abnormality in appearance. LBM Series Test Methods and Remarks LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： The given sample is soldered to the board and then its Inductance is measured after 100cycles of the following conditions. Conditions of 1 cycle Step Temperature (℃) Duration (min) 1 －40±3 30±3 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01 18.Damp heat life test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within±10％ No significant abnormality in appearance. LBM Series Test Methods and Remarks Temperature Humidity Duration Recovery : 60±2℃ : 90～95％RH : 1000 hrs : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 19.Loading under damp heat life test LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series Specified Value Test Methods and Remarks Inductance change : Within±10％ No significant abnormality in appearance. LBM Series Temperature Humidity Duration Applied current Recovery : 60±2℃ : 90～95％RH : 1000 hrs : Rated current : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 20.High temperature life test Specified Value LB, LBC, LBR, LBMF Series － CB, CBC, CBL, CBMF Series Inductance change : Within±10％ No significant abnormality in appearance. LBM Series Test Methods and Remarks Temperature Duration Recovery : 85±2℃ : 1000 hrs : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 21.Loading at high temperature life test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series Test Methods and Remarks Temperature Duration Applied current Recovery Inductance change : Within±10％ （LBC3225 Series : Within±20％） No significant abnormality in appearance. － : 85±2℃ : 1000 hrs : Rated current : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 22.Low temperature life test LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series Inductance change : Within±10％ No significant abnormality in appearance. LBM Series Test Methods and Remarks Temperature Duration Recovery : －40±2℃ : 1000 hrs : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 23.Standard condition LB, LBC, LBR, LBMF Series Specified Value CB, CBC, CBL, CBMF Series LBM Series Standard test conditions Unless specified, Ambient temperature is 20±15℃ and the Relative humidity is 65±20％. If there is any doubt about the test results, further measurement shall be had within the following limits: Ambient Temperature: 20±2℃ Relative humidity: 65±5％ Inductance value is based on our standard measurement systems. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_reli_e-E05R01 WIRE-WOUND CHIP INDUCTORS (LB SERIES)， WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)， WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE) ■PRECAUTIONS 1．Circuit Design Precautions ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2．PCB Design Precautions Technical considerations ◆Land pattern design 1. Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications. PRECAUTIONS 【Recommended Land Patterns】 Surface Mounting ・ Mounting and soldering conditions should be checked beforehand. ・ Applicable soldering process to those products is reflow soldering only. 3．Considerations for automatic placement Precautions Technical considerations ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4．Soldering Precautions ◆Reflow soldering（ LB and CB Types） 1. For reflow soldering with either leaded or lead-free solder, the profile specified in "point for controlling" is recommended. ◆Recommended conditions for using a soldering iron 1. Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350℃ Duration-3 seconds or less. The soldering iron should not come in contact with inductor directly. ◆Reflow soldering（ LB and CB Types） 1. Reflow profile Technical considerations ◆Recommended conditions for using a soldering iron 1. Components can be damaged by excessive heat where soldering conditions exceed the specified range. 5．Cleaning Precautions Technical considerations ◆Cleaning conditions Washing by supersonic waves shall be avoided. ◆Cleaning conditions If washed by supersonic waves, the products might be broken. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01 6．Handling Precautions Technical considerations ◆Handling 1. Keep the inductors away from all magnets and magnetic objects. ◆Breakaway PC boards（ splitting along perforations） 1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Breakaway PC boards（ splitting along perforations） 1. Planning pattern configurations and the position of products should be carefully performed to minimize stress. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 7．Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : 0～40℃ Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_CB_LB_prec_e-E06R01