Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product Information in this Catalog
Product information in this catalog is as of October 2019. All of the
contents specified herein and production status of the products listed
in this catalog are subject to change without notice due to technical
improvement of our products, etc. Therefore, please check for the
latest information carefully before practical application or use of our
products.
(4) Powe r g e n e r atio n c o ntro l e quip m e nt (nu c le a r p owe r,
hydroelectric power, thermal power plant control system, etc.)
(5) Undersea equipment (submarine repeating equipment,
underwater work equipment, etc.)
(6) Military equipment
(7) Any other equipment requiring extremely high levels of safety
and/or reliability equal to the equipment listed above
Please note that TAIYO YUDEN shall not be in any way responsible
for any damages and defects in products or equipment incorporating
our products, which are caused under the conditions other than those
specified in this catalog or individual product specification sheets.
*Notes:
1. There is a possibility that our products can be used only
for aviation equipment that does not directly affect the safe
operation of aircraft (e.g., in-flight entertainment, cabin
light, electric seat, cooking equipment) if such use meets
requirements specified separately by TAIYO YUDEN. Please
be sure to contact TAIYO YUDEN for further information
before using our products for such aviation equipment.
2. Implantable medical devices contain not only internal unit
which is implanted in a body, but also external unit which is
connected to the internal unit.
■ Approval of Product Specifications
Ple a se c ont ac t TA IYO Y UD EN for fur the r det a ils of p ro duc t
specifications as the individual product specification sheets are
available. When using our products, please be sure to approve our
product specifications or make a written agreement on the product
specification with TAIYO YUDEN in advance.
■ Pre-Evaluation in the Actual Equipment and Conditions
Please conduct validation and verification of our products in actual
conditions of mounting and operating environment before using our
products.
■ Limited Application
1. Equipment Intended for Use
The products listed in this catalog are intended for generalpurpose and standard use in general electronic equipment (e.g.,
AV equipment, OA equipment, home electric appliances, office
equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and other equipment
specified in this catalog or the individual product specification sheets.
TAIYO YUDEN has the line-up of the products intended for
use in automotive electronic equipment, telecommunications
infrastructure and industrial equipment, or medical devices
classified as GHTF Classes A to C (Japan Classes I to III).
Therefore, when using our products for these equipment,
please check available applications specified in this catalog
or the individual product specification sheets and use the
corresponding products.
2. Equipment Requiring Inquiry
Please be sure to contact TAIYO YUDEN for further information
before using the products listed in this catalog for the following
equipment (excluding intended equipment as specified in this
catalog or the individual product specification sheets) which may
cause loss of human life, bodily injury, serious property damage
and/or serious public impact due to a failure or defect of the
products and/or malfunction attributed thereto.
(1) Transportation equipment (automotive powertrain control
system, train control system, and ship control system, etc.)
(2) Traffic signal equipment
(3) Disaster prevention equipment, crime prevention equipment
(4) Medical devices classified as GHTF Class C (Japan Class III)
(5) H i g h l y p u b l i c i n f o r m a t i o n n e t wo r k e q u i p m e n t , d a t a processing equipment (telephone exchange, and base
station, etc.)
(6) Any other equipment requiring high levels of quality and/or
reliability equal to the equipment listed above
3. Equipment Prohibited for Use
Please do not incorporate our products into the following
equipment requiring extremely high levels of safety and/or
reliability.
(1) Aerospace equipment (artificial satellite, rocket, etc.)
(2) Aviation equipment *1
(3) Medical devices classified as GHTF Class D (Japan Class IV),
implantable medical devices *2
4. Limitation of Liability
Please note that unless you obtain prior written consent of TAIYO
YUDEN, TAIYO YUDEN shall not be in any way responsible for
any damages incurred by you or third parties arising from use of
the products listed in this catalog for any equipment that is not
intended for use by TAIYO YUDEN, or any equipment requiring
inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN
as described above.
■ Safety Design
When using our products for high safety and/or reliability-required
equipment or circuits, please fully perform safety and/or reliability
evaluation. In addition, please install (i) systems equipped with
a protection circuit and a protection device and/or (ii) systems
equipped with a redundant circuit or other system to prevent an
unsafe status in the event of a single fault for a failsafe design to
ensure safety.
■ Intellectual Property Rights
Information contained in this catalog is intended to convey examples
of typical performances and/or applications of our products and is
not intended to make any warranty with respect to the intellectual
property rights or any other related rights of TAIYO YUDEN or any
third parties nor grant any license under such rights.
■ Limited Warranty
Please note that the scope of warranty for our products is limited to
the delivered our products themselves and TAIYO YUDEN shall not
be in any way responsible for any damages resulting from a failure
or defect in our products. Notwithstanding the foregoing, if there is
a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company,
TAIYO YUDEN will warrant our products in accordance with such
agreement.
■ TAIYO YUDEN’s Official Sales Channel
The contents of this catalog are applicable to our products which are
purchased from our sales offices or authorized distributors (hereinafter
“TAIYO YUDEN’
s official sales channel”). Please note that the contents
of this catalog are not applicable to our products purchased from any
seller other than TAIYO YUDEN’
s official sales channel.
■ Caution for Export
Some of our products listed in this catalog may require specific
procedures for export according to“U.S. Export Administration
Regulations”,“Foreign Exchange and Foreign Trade Control Law”
of Japan, and other applicable regulations. Should you have any
questions on this matter, please contact our sales staff.
20
for General Electronic Equipment
for General Electronic Equipment
CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE)
CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE)
WAVE
REFLOW
WAVE
■PARTS NUMBER
F
B
△
①
REFLOW
*Operating Temp. : -40~+125℃(Including self-generated heat)
M J
② ③
3
2
1
6
H
④
①Series name
Code
FB
S
8
⑤
0 0
⑥
- T △
⑦ ⑧ ⑨
⑤Material
Code
HS
HM
HL
Series name
Ferrite bead
②Shape
Code
M
Shape
Rectangular chip
④Dimensions(L×W)
1608
2125
2012
2016
3216
3225
4516
4525
4532
1608(0603)
2125(0805)
2012(0805)
2016(0806)
3216(1206)
3225(1210)
4516(1806)
4525(1810)
4532(1812)
⑦Impedance tolerance
Code
-
N
Dimensions
(L×W)[mm]
1.6×0.8
2.0×1.25
Nominal impedance[Ω]
33
220
1000
Impedance tolerance
±25%
±30%
⑧Packaging
Code
T
2.0×1.6
3.2×1.6
3.2×2.5
4.5×1.6
4.5×2.5
4.5×3.2
Packaging
Taping
⑨Internal code
Code
△
Internal code
Standard
■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
Type
FB MJ1608
FB MJ2125
FB MJ3216
FB MJ4516
FB MH1608
FB MH2012
FB MH2016
FB MH3216
FB MH3225
FB MH4516
FB MH4525
FB MH4532
Recommended Land Patterns
Surface Mounting
・Mounting and soldering conditions should be
checked beforehand.
W
L
T
C
e
A
B
A
A
1.0
1.4
1.4
1.75
1.0
1.4
1.4
1.4
1.4
1.75
1.75
1.75
B
1.0
1.2
2.2
3.5
1.0
1.2
1.2
2.2
2.2
3.5
3.5
3.5
C
1.0
1.65
2.0
2.0
1.0
1.65
2.0
2.0
2.9
2.0
2.9
3.7
FERRITE BEAD INDUCTORS
Type(inch)
Refer to impedance curves
for material differences
⑥Nominal impedance
Code
(example)
330
221
102
Characteristics
Standard
High Impedance type
Code
Material
NOISE SUPPRESSION
COMPONENTS
③Characteristics
Code
J
H
△=Blank space
Unit:mm
Standard quantity [pcs]
Paper tape
Embossed tape
Type
L
W
T
e
FB MJ1608
(0603)
FB MJ2125
(0805)
FB MJ3216
(1206)
FB MJ4516
(1806)
FB MH1608
(0603)
FB MH2012
(0805)
FB MH2016
(0806)
FB MH3216
(1206)
FB MH3225
(1210)
FB MH4516
(1806)
FB MH4525
(1810)
FB MH4532
(1812)
1.6±0.2
(0.063±0.008)
2.0±0.2
(0.079±0.008)
3.2±0.3
(0.126±0.012)
4.5±0.3
(0.177±0.012)
1.6±0.1
(0.063±0.004)
2.0±0.2
(0.079±0.008)
2.0±0.2
(0.079±0.008)
3.2±0.3
(0.126±0.012)
3.2±0.3
(0.126±0.012)
4.5±0.3
(0.177±0.012)
4.5±0.4
(0.177±0.016)
4.5±0.4
(0.177±0.016)
0.8±0.2
(0.031±0.008)
1.25±0.2
(0.049±0.008)
1.6±0.2
(0.063±0.008)
1.6±0.2
(0.063±0.008)
0.8±0.1
(0.031±0.004)
1.25±0.2
(0.049±0.008)
1.6±0.2
(0.063±0.008)
1.6±0.2
(0.063±0.008)
2.5±0.3
(0.098±0.012)
1.6±0.2
(0.063±0.008)
2.5±0.3
(0.098±0.012)
3.2±0.3
(0.126±0.012)
0.8±0.2
(0.031±0.008)
0.85±0.2
(0.033±0.008)
1.1±0.2
(0.043±0.008)
1.1±0.2
(0.043±0.008)
0.8±0.1
(0.031±0.004)
0.85±0.2
(0.033±0.008)
1.6±0.2
(0.063±0.008)
1.6±0.2
(0.063±0.008)
2.5±0.3
(0.098±0.012)
1.6±0.2
(0.063±0.008)
2.5±0.3
(0.098±0.012)
3.2±0.3
(0.126±0.012)
0.3±0.2
(0.012±0.008)
0.5±0.3
(0.020±0.012)
0.5±0.3
(0.020±0.012)
0.5±0.3
(0.020±0.012)
0.3±0.15
(0.012±0.006)
0.5±0.3
(0.020±0.012)
0.5±0.3
(0.020±0.012)
0.5±0.3
(0.020±0.012)
0.5±0.3
(0.020±0.012)
0.5±0.3
(0.020±0.012)
0.9±0.6
(0.035±0.024)
0.9±0.6
(0.035±0.024)
4000
-
4000
-
-
2000
-
2000
4000
-
4000
-
-
2000
-
2000
-
1000
-
2000
-
1000
-
2000
Unit:mm(inch)
chipbeads_e-E08R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
20
119
for General Electronic Equipment
■PARTS NUMBER
Standard type
●FB MJ1608
Parts number
FB MJ1608HS280NT
FB MJ1608HM230NT
EHS
RoHS
RoHS
Nominal impedance
(Ω)
28
23
Impedance tolerance
±30%
±30%
Measuring frequency
[MHz]
100
100
DC Resistance
[Ω](max.)
Rated current
[A](max.)
Thickness
[mm]
0.007
0.007
4.0
4.0
Measuring frequency
[MHz]
100
100
100
100
100
DC Resistance
[Ω](max.)
Rated current
[A](max.)
0.004
0.008
0.004
0.008
0.008
6.0
4.0
6.0
4.0
4.0
Measuring frequency
[MHz]
100
100
100
100
100
DC Resistance
[Ω](max.)
Rated current
[A](max.)
0.005
0.010
0.005
0.010
0.012
6.0
4.0
6.0
4.0
4.0
Measuring frequency
[MHz]
100
100
100
100
100
DC Resistance
[Ω](max.)
Rated current
[A](max.)
0.007
0.014
0.007
0.014
0.014
6.0
4.0
6.0
4.0
3.5
DC Resistance
[Ω](max.)
Rated current
[A](max.)
0.020
0.025
0.035
0.050
0.070
0.130
0.150
0.170
0.350
0.028
0.045
0.130
0.170
0.210
0.350
0.450
3.5
3.0
2.5
2.1
1.8
1.2
1.0
0.9
0.6
2.6
2.1
1.2
0.9
0.8
0.6
0.5
Measuring frequency
[MHz]
100
100
100
100
DC Resistance
[Ω](max.)
0.025
0.032
0.060
0.080
Rated current
[A](max.)
2.7
2.5
2.0
1.8
Thickness
[mm]
0.85 ±0.2
0.85 ±0.2
0.85 ±0.2
0.85 ±0.2
Measuring frequency
[MHz]
100
100
DC Resistance
[Ω](max.)
0.015
0.050
Rated current
[A](max.)
4.5
2.0
Thickness
[mm]
1.6 ±0.2
1.6 ±0.2
Measuring frequency
[MHz]
100
100
DC Resistance
[Ω](max.)
0.020
0.070
Rated current
[A](max.)
4.0
2.0
Thickness
[mm]
1.6 ±0.2
1.6 ±0.2
Measuring frequency
[MHz]
100
100
100
DC Resistance
[Ω](max.)
0.042
0.100
0.130
Rated current
[A](max.)
3.0
2.0
1.2
Thickness
[mm]
2.5 ±0.3
2.5 ±0.3
2.5 ±0.3
0.8 ±0.2
0.8 ±0.2
●FB MJ2125
FB
FB
FB
FB
FB
Parts number
EHS
MJ2125HS250NT
MJ2125HS420-T
MJ2125HM210NT
MJ2125HM330-T
MJ2125HL8R0NT
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal impedance
(Ω)
25
42
21
33
8
Impedance tolerance
±30%
±25%
±30%
±25%
±30%
Thickness
[mm]
0.85
0.85
0.85
0.85
0.85
±0.2
±0.2
±0.2
±0.2
±0.2
●FB MJ3216
NOISE SUPPRESSION
COMPONENTS
FB
FB
FB
FB
FB
Parts number
EHS
MJ3216HS480NT
MJ3216HS800-T
MJ3216HM380NT
MJ3216HM600-T
MJ3216HL160NT
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal impedance
(Ω)
48
80
38
60
16
Impedance tolerance
±30%
±25%
±30%
±25%
±30%
Thickness
[mm]
1.1
1.1
1.1
1.1
1.1
±0.2
±0.2
±0.2
±0.2
±0.2
●FB MJ4516
FERRITE BEAD INDUCTORS
FB
FB
FB
FB
FB
Parts number
EHS
MJ4516HS720NT
MJ4516HS111-T
MJ4516HM560NT
MJ4516HM900-T
MJ4516HL230NT
RoHS
RoHS
RoHS
RoHS
RoHS
High impedance type
●FB MH1608
Parts number
FB MH1608HM470-T
FB MH1608HM600-T
FB MH1608HM101-T
FB MH1608HM151-T
FB MH1608HM221-T
FB MH1608HM331-T
FB MH1608HM471-T
FB MH1608HM601-T
FB MH1608HM102-T
FB MH1608HL300-T
FB MH1608HL600-T
FB MH1608HL121-T
FB MH1608HL221-T
FB MH1608HL331-T
FB MH1608HL471-T
FB MH1608HL601-T
Nominal impedance
(Ω)
72
110
56
90
23
Impedance tolerance
±30%
±25%
±30%
±25%
±30%
Thickness
[mm]
1.1
1.1
1.1
1.1
1.1
±0.2
±0.2
±0.2
±0.2
±0.2
GHz Band
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal impedance
Measuring frequency 100[MHz]
(Ω)
tolerance
47
±25%
60
±25%
100
±25%
150
±25%
220
±25%
330
±25%
470
±25%
600
±25%
1000
±25%
30
±25%
60
±25%
120
±25%
220
±25%
330
±25%
470
±25%
600
±25%
Nominal impedance
Measuring frequency 1[GHz]
(Ω)
tolerance
75
±40%
100
±40%
170
±40%
270
±40%
370
±40%
520
±40%
750
±40%
900
±40%
1200
±40%
120
±40%
220
±40%
540
±40%
950
±40%
1200
±40%
1500
±40%
1800
±40%
Thickness
[mm]
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
High impedance type
●FB MH2012
FB
FB
FB
FB
Parts number
EHS
MH2012HM800-T
MH2012HM121-T
MH2012HM221-T
MH2012HM331-T
RoHS
RoHS
RoHS
RoHS
Nominal impedance
(Ω)
80
120
220
330
Impedance tolerance
±25%
±25%
±25%
±25%
●FB MH2016
Parts number
FB MH2016HM121NT
FB MH2016HM251NT
EHS
RoHS
RoHS
Nominal impedance
(Ω)
120
250
Impedance tolerance
±30%
±30%
●FB MH3216
Parts number
FB MH3216HM221NT
FB MH3216HM501NT
EHS
RoHS
RoHS
Nominal impedance
(Ω)
220
500
Impedance tolerance
±30%
±30%
●FB MH3225
Parts number
FB MH3225HM601NT
FB MH3225HM102NT
FB MH3225HM202NT
EHS
RoHS
RoHS
RoHS
Nominal impedance
(Ω)
600
1000
2000
Impedance tolerance
±30%
±30%
±30%
chipbeads_e-E08R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
120
20
for General Electronic Equipment
■PARTS NUMBER
●FB MH4516
Parts number
FB MH4516HM851NT
EHS
RoHS
Nominal impedance
(Ω)
850
Impedance tolerance
±30%
Measuring frequency
[MHz]
100
DC Resistance
[Ω](max.)
0.100
Rated current
[A](max.)
1.5
Thickness
[mm]
1.6 ±0.2
Measuring frequency
[MHz]
100
100
DC Resistance
[Ω](max.)
0.060
0.130
Rated current
[A](max.)
3.0
2.0
Thickness
[mm]
2.5 ±0.3
2.5 ±0.3
Measuring frequency
[MHz]
100
100
100
DC Resistance
[Ω](max.)
0.028
0.060
0.130
Rated current
[A](max.)
4.0
3.0
1.3
Thickness
[mm]
3.2 ±0.3
3.2 ±0.3
3.2 ±0.3
Measuring frequency
[MHz]
100
100
100
100
DC Resistance
[Ω](max.)
0.004
0.006
0.004
0.006
Rated current
[A](max.)
7.5
6.0
7.5
6.0
Thickness
[mm]
0.8 ±0.2
0.8 ±0.2
0.8 ±0.2
0.8 ±0.2
●FB MH4525
Parts number
FB MH4525HM102NT
FB MH4525HM162NT
EHS
RoHS
RoHS
Nominal impedance
(Ω)
1000
1600
Impedance tolerance
±30%
±30%
●FB MH4532
Parts number
FB MH4532HM681-T
FB MH4532HM132-T
FB MH4532HM202-T
EHS
RoHS
RoHS
RoHS
Nominal impedance
(Ω)
680
1300
2000
Impedance tolerance
±25%
±25%
±25%
●High current type
FB
FB
FB
FB
MJ1608HS220NTR
MJ1608HS280NTR
MJ1608HM180NTR
MJ1608HM230NTR
EHS
RoHS
RoHS
RoHS
RoHS
Nominal impedance
(Ω)
22
28
18
23
Impedance tolerance
±30%
±30%
±30%
±30%
NOISE SUPPRESSION
COMPONENTS
Parts number
FERRITE BEAD INDUCTORS
chipbeads_e-E08R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
20
121
for General Electronic Equipment
■ELECTRICAL CHARACTERISTICS
Standard type
■FB MJ1608
■FB MJ2125
FB MJ1608HS280NT
35
50
30
25
R
15
Z
30
R
20
10
X
10
X
5
0
10
100
1000
10
Frequency[MHz]
100
1000
10000
1000
10000
60
Z
30
R
20
50
Z
40
R
30
20
X
10
X
1000
10000
0
1
10
Frequency[MHz]
100
1000
10000
1
10
Frequency[MHz]
100
1000
10000
Frequency[MHz]
■FB MJ3216
FB MJ2125HL8R0NT
50
FB MJ3216HS480NT
60
R
Z
20
X
10
80
40
Z
30
R
20
X
10
0
10
100
1000
10000
10
100
1000
1
10000
R
20
X
10
Z
60
R
40
10
100
1000
10000
60
R
Z
40
X
X
0
1
10000
20
20
0
1000
80
80
Impedance[Ω]
Impedance[Ω]
Z
100
FB MJ3216HL160NT
100
100
60
30
10
Frequency[MHz]
FB MJ3216HM600-T
120
70
40
X
Frequency[MHz]
FB MJ3216HM380NT
50
R
40
0
1
Frequency[MHz]
80
Z
60
20
0
1
Impedance[Ω]
Impedance[Ω]
30
FB MJ3216HS800-T
100
50
40
Impedance[Ω]
FERRITE BEAD INDUCTORS
100
X
10
0
10
100
FB MJ2125HM330-T
70
Impedance[Ω]
Impedance[Ω]
R
0
Impedance[Ω]
NOISE SUPPRESSION
COMPONENTS
30
1
10
Frequency[MHz]
40
Z
10
X
1
FB MJ2125HM210NT
50
40
20
R
10
Frequency[MHz]
FB MJ2125HS420-T
50
15
0
1
10000
Z
20
5
0
1
Impedance[Ω]
Impedance[Ω]
Z
20
FB MJ2125HS250NT
30
40
25
Impedance[Ω]
Impedance[Ω]
FB MJ1608HM230NT
0
1
10
Frequency[MHz]
100
1000
1
10000
10
Frequency[MHz]
100
1000
10000
Frequency[MHz]
■FB MJ4516
FB MJ4516HS720NT
100
R
40
Z
80
R
60
40
X
20
100
100
Impedance[Ω]
Impedance[Ω]
Z
60
X
0
1
10
100
1000
Frequency[MHz]
10000
80
Z
60
R
40
X
20
20
0
FB MJ4516HM560NT
120
120
80
Impedance[Ω]
FB MJ4516HS111-T
140
0
1
10
100
1000
10000
Frequency[MHz]
1
10
100
1000
10000
Frequency[MHz]
chipbeads_char_e-E08R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
122
20
for General Electronic Equipment
■ELECTRICAL CHARACTERISTICS
FB MJ4516HM900-T
160
140
120
120
Z
100
Impedance[Ω]
Impedance[Ω]
FB MJ4516HL230NT
140
R
80
60
100
80
R
Z
60
X
40
40
X
20
20
0
0
1
10
100
1000
10000
1
10
Frequency[MHz]
100
1000
10000
Frequency[MHz]
High impedance type GHz Band
■FB MH1608
70
R
40
30
20
X
Z
R
60
40
0
0
1
10
100
1000
10000
10
1
10000
Z
R
100
250
R
200
150
X
100
1000
10
Frequency[MHz]
100
1000
10000
300
200
X
100
600
R
400
10
100
1000
10000
10
100
1000
X
1000
10000
1000
10000
600
250
Z
200
R
150
500
Z
400
R
300
200
100
X
0
100
100
FB MH1608HL121-T
700
100
0
Frequency[MHz]
10
Frequency[MHz]
50
10
X
1
Impedance[Ω]
Impedance[Ω]
Impedance[Ω]
R
50
1
600
10000
300
100
R
800
200
FB MH1608HL600-T
350
150
Z
Z
1000
Frequency[MHz]
FB MH1608HL300-T
10000
0
1
Frequency[MHz]
200
1200
400
X
0
1
1000
1400
Z
200
0
100
FB MH1608HM102-T
1600
Impedance[Ω]
Impedance[Ω]
R
400
10
Frequency[MHz]
800
Z
500
X
1
FB MH1608HM601-T
1000
700
600
200
Frequency[MHz]
FB MH1608HM471-T
800
R
300
0
1
10000
10000
Z
400
100
0
10
1000
500
Z
50
0
100
FB MH1608HM331-T
600
300
100
X
1
10
Frequency[MHz]
Impedance[Ω]
Impedance[Ω]
Impedance[Ω]
1000
350
50
Impedance[Ω]
100
FB MH1608HM221-T
400
250
150
X
Frequency[MHz]
FB MH1608HM151-T
200
R
0
1
Frequency[MHz]
300
Z
100
50
X
20
150
FERRITE BEAD INDUCTORS
10
80
Impedance[Ω]
Z
50
FB MH1608HM101-T
200
100
60
Impedance[Ω]
Impedance[Ω]
FB MH1608HM600-T
120
NOISE SUPPRESSION
COMPONENTS
FB MH1608HM470-T
80
X
0
1
10
100
1000
10000
Frequency[MHz]
1
10
100
1000
10000
Frequency[MHz]
chipbeads_char_e-E08R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
20
123
for General Electronic Equipment
■ELECTRICAL CHARACTERISTICS
FB MH1608HL221-T
1200
FB MH1608HL471-T
2000
1400
Z
R
600
400
1200
1000
Impedance[Ω]
800
Impedance[Ω]
1000
Impedance[Ω]
FB MH1608HL331-T
1600
Z
800
R
600
400
200
0
10
100
1000
X
0
1
10000
R
X
0
1
Z
1000
500
200
X
1500
10
Frequency[MHz]
100
1000
1
10000
10
Frequency[MHz]
100
1000
10000
Frequency[MHz]
FB MH1608HL601-T
2500
Impedance[Ω]
Z
1500
R
1000
500
X
0
10
100
1000
10000
Frequency[MHz]
High impedance type
■FB MH2012
FB MH2012HM800-T
140
FB MH2012HM121-T
200
FB MH2012HM221-T
400
350
120
80
R
60
40
Z
150
Impedance[Ω]
Z
100
Impedance[Ω]
FERRITE BEAD INDUCTORS
1
Impedance[Ω]
NOISE SUPPRESSION
COMPONENTS
2000
R
100
50
X
1
10
100
1000
R
200
150
50
X
0
1
10000
250
100
20
0
Z
300
10
Frequency[MHz]
100
X
0
1000
10000
1
10
Frequency[MHz]
100
1000
10000
Frequency[MHz]
■FB MH2016
600
Z
Impedance[Ω]
Impedance[Ω]
500
400
300
FB MH2016HM121NT
200
R
200
350
Z
150
R
100
50
100
X
0
1
10
100
1000
Z
250
R
200
150
1
10
100
X
50
X
Frequency[MHz]
0
1000
10000
1
10
Frequency[MHz]
100
1000
10000
Frequency[MHz]
■FB MH3216
■FB MH3225
300
800
700
Z
Impedance[Ω]
250
200
FB MH3216HM501NT
R
150
100
500
R
400
300
200
50
1
10
100
1000
Frequency[MHz]
R
500
Z
400
300
100
0
10000
600
200
X
100
X
0
700
Z
600
FB MH3225HM601NT
800
Impedance[Ω]
FB MH3216HM221NT
350
Impedance[Ω]
300
100
0
10000
FB MH2016HM251NT
400
Impedance[Ω]
FB MH2012HM331-T
X
0
1
10
100
1000
10000
Frequency[MHz]
1
10
100
1000
10000
Frequency[MHz]
chipbeads_char_e-E08R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
124
20
for General Electronic Equipment
■ELECTRICAL CHARACTERISTICS
■FB MH4516
FB MH3225HM102NT
2500
800
Z
600
1200
2000
R
Impedance[Ω]
Impedance[Ω]
1000
400
1500
Z
R
1000
500
0
0
100
1000
R
600
X
0
1
10000
10
Frequency[MHz]
100
1000
10000
1
10
Frequency[MHz]
100
1000
10000
Frequency[MHz]
■FB MH4525
■FB MH4532
FB MH4525HM102NT
FB MH4525HM162NT
2000
1200
R
800
Z
600
400
800
1500
R
Z
1000
500
X
10
100
1000
X
0
1
10000
Z
400
10
100
1000
Frequency[MHz]
Frequency[MHz]
FB MH4532HM132-T
FB MH4532HM202-T
1
10000
10
100
1000
10000
Frequency[MHz]
■High current type
1600
2500
25
R
1000
Z
800
600
400
Z
0
10
100
1000
10
Frequency[MHz]
100
1000
10000
Z
R
10
Z
25
20
R
15
0
1
10
100
1000
Frequency[MHz]
10000
10000
Z
30
R
20
X
10
X
5
0
1000
40
30
10
X
100
FB MJ1608HM230NTR
50
Impedance[Ω]
Impedance[Ω]
25
5
10
Frequency[MHz]
35
15
X
1
FB MJ1608HM180NTR
40
30
20
R
10
Frequency[MHz]
FB MJ1608HS280NTR
35
Z
15
0
1
10000
20
5
X
0
1
Impedance[Ω]
R
1000
500
X
200
1500
Impedance[Ω]
2000
1200
Impedance[Ω]
Impedance[Ω]
1400
FB MJ1608HS220NTR
30
FERRITE BEAD INDUCTORS
0
1
R
600
200
X
200
0
Impedance[Ω]
Impedance[Ω]
1000
FB MH4532HM681-T
1000
NOISE SUPPRESSION
COMPONENTS
1400
Impedance[Ω]
800
200
X
10
Z
1000
400
X
200
1
FB MH4516HM851NT
1400
Impedance[Ω]
1200
FB MH3225HM202NT
0
1
10
100
1000
10000
Frequency[MHz]
1
10
100
1000
10000
Frequency[MHz]
chipbeads_char_e-E08R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
20
125
CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE / T TYPE)
■PACKAGING
①Minimum Quantity
Standard Quantity[pcs]
Paper Tape
Embossed Tape
4000
-
4000
-
4000
-
-
2000
-
2000
-
1000
-
2000
-
1000
-
2000
Type
1608(0603)
2125(0805)
2012(0805)
2016(0806)
3216(1206)
3225(1210)
4516(1806)
4525(1810)
4532(1812)
②Tape Material
●Card board carrier tape
Top tape
Base tape
Chip Filled
Sprocket hole
Bottom tape
Chip cavity
Chip
●Embossed tape
Top tape
Chip Filled
Sprocket hole
Base tape
Chip cavity
Chip
③Taping Dimensions
●Paper tape (0.315 inches wide)
A
B
F
1.75±0.1
(0.069±0.004)
T
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
3.5±0.05
(0.138±0.002)
Sprocket hole
4.0±0.1
(0.157±0.004)
2.0±0.05
(0.079±0.002)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_pack_e-E08R01
A
Chip Cavity
B
Insertion Pitch
F
Tape Thickness
T
1.0±0.2
(0.039±0.008)
1.8±0.2
(0.071±0.008)
4.0±0.2
(0.157±0.008)
1.1max
(0.043max)
1.5±0.2
(0.059±0.008)
2.3±0.2
(0.091±0.008)
4.0±0.2
(0.157±0.008)
1.1max
(0.043max)
Type
FB MJ1608
FB MH1608
FB TH1608
(0603)
FB MJ2125
FB MH2012
(0805)
Unit : mm(inch)
●Embossed tape (0.315 inches wide)
3.5±0.05
(0.138±0.002)
A
B
F
8.0±0.3
(0.315±0.012)
1.75±0.1
(0.069±0.004)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
4.0±0.1
(0.157±0.004)
2.0±0.05
(0.079±0.002)
Chip Cavity
A
B
1.8±0.2
2.2±0.2
(0.071±0.008)
(0.087±0.008)
1.9±0.2
3.5±0.2
(0.075±0.008)
(0.138±0.008)
1.9±0.2
3.5±0.2
(0.075±0.008)
(0.138±0.008)
2.8±0.2
3.5±0.2
(0.110±0.008)
(0.138±0.008)
Type
FB MH2016
(0806)
FB MJ3216
(1206)
FB MH3216
(1206)
FB MH3225
(1210)
Insertion Pitch
F
4.0±0.2
(0.157±0.008)
4.0±0.2
(0.157±0.008)
4.0±0.2
(0.157±0.008)
4.0±0.2
(0.157±0.008)
Tape Thickness
K
T
2.6max
0.6max
(0.102max)
(0.024max)
1.5max
0.3max
(0.059max)
(0.012max)
2.6max
0.6max
(0.102max)
(0.024max)
4.0max
0.6max
(0.157max)
(0.024max)
Unit : mm(inch)
Insertion Pitch
F
4.0±0.2
(0.157±0.008)
4.0±0.2
(0.157±0.008)
4.0±0.2
(0.157±0.008)
8.0±0.2
(0.315±0.008)
Tape Thickness
K
T
1.5max
0.3max
(0.059max)
(0.012max)
2.6max
0.6max
(0.102max)
(0.024max)
4.0max
0.6max
(0.157max)
(0.024max)
4.0max
0.6max
(0.157max)
(0.024max)
Unit : mm(inch)
●Embossed tape (0.472 inches wide)
5.5±0.05
(0.217±0.002)
1.75±0.1
(0.069±0.004)
A
B
T
12.0±0.3
(0.472±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
K
F
2.0±0.05
(0.079±0.002)
Type
FB MJ4516
(1806)
FB MH4516
(1806)
FB MH4525
(1810)
FB MH4532
(1812)
4.0±0.1
(0.157±0.004)
Chip Cavity
A
B
1.9±0.2
4.9±0.2
(0.075±0.008)
(0.193±0.008)
1.9±0.2
4.9±0.2
(0.075±0.008)
(0.193±0.008)
2.9±0.2
4.9±0.2
(0.114±0.008)
(0.193±0.008)
3.6±0.2
4.9±0.2
(0.142±0.008)
(0.193±0.008)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_pack_e-E08R01
④Leader and Blank portion
⑤Reel size
2.0±0.5
(0.079±0.020)
t
φ13.0±0.5
(φ0.512±0.020)
R1.0
φd
φ21.0±0.8
(φ0.827±0.031)
φD
W
Type
FB MJ1608
FB MJ2125
FB MJ3216
φD
φd
MH1608
MH2012
MH2016
MH3216
MH3225
MH4516
MH4525
FB MH4532
FB TH1608
t
10.0±1.5
(0.394±0.059)
14.0±1.5
(0.551±0.059)
FB MJ4516
FB
FB
FB
FB
FB
FB
FB
W
180+0/-3
(7.09+0/-0.118 )
330±2.0
(12.99±0.080)
180+0/-3
(7.09+0/-0.118 )
60+1/-0
(2.36+0.039/-0 )
100±1.0
(3.94±0.039)
60+1/-0
(2.36+0.039/-0 )
10.0±1.5
(0.394±0.059)
14.0±1.5
(0.551±0.059)
14.0±2.0
(0.551±0.080)
10.0±1.5
(0.394±0.059)
2.5max
(0.098max)
3.0max
(1.181max)
2.5max
(0.098max)
Unit : mm(inch)
⑥Top tape strength
The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_pack_e-E08R01
CHIP BEAD INDUCTORS FOR POWER LINE (FB SERIES M TYPE)
■RELIABILITY DATA
1. Operating Temperature Range
Specified Value
-40℃~+125℃
Including self-generated heat
2. Storage Temperature Range
Specified Value
-40℃~+85℃
Test Methods and
Remarks
*Note: -5 to +40℃ in taped packaging
3. Impedance
Specified Value
Within the specified tolerance
Test Methods and
Remarks
Measuring equipment
Measuring frequency
: Impedance analyzer (HP4291A) or its equivalent
: 100±1 MHz
4. DC Resistance
Specified Value
Within the specified range
Test Methods and
Remarks
Four-terminal method
Measuring equipment : Milliohm High-Tester 3226 (Hioki Denki) or its equivalent
5. Rated Current
Specified Value
Within the specified range
6. Vibration
Specified Value
Appearance
Impedance change
: No significant abnormality
: Within ±30% of the initial value
Test Methods and
Remarks
According to JIS C60068-2-6.
Vibration type
:A
Time
: 2 hrs each in X,Y, and Z directions Total: 6 hrs
Frequency range
: 10 to 55 to 10Hz (/min.)
Amplitude
: 1.5 mm (shall not exceed acceleration 196m/s2)
Mounting method
: Soldering onto PC board
7. Solderability
Specified Value
90% or more of immersed surface of terminal electrode shall be covered with fresh solder.
Test Methods and
Remarks
Solder temperature
Immersion time
Preconditioning
Immersion and Removal speed
:
:
:
:
230±5℃
4±1 sec.
Immersion into flux.
25mm/sec.
8. Resistance to Soldering Heat
Specified Value
Appearance
Impedance change
: No significant abnormality
: Within ±30% of the initial value
Test Methods and
Remarks
Preheating
Resistance to Soldering Heat
Duration
Preconditioning
Immersion and Removal speed
Recovery
:
:
:
:
:
:
150℃ for 3 min.
260±5℃
10±0.5 sec.
Immersion into flux.
25mm/sec.
2 to 3 hrs of recovery under the standard condition after the test.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_reli_e-E04R01
9. Thermal Shock
Specified Value
Test Methods and
Remarks
Appearance
Impedance change
: No significant abnormality
: Within+50/-10% of the initial value
According to JIS C60068-2-14.
Conditions for 1 cycle
Step
Temperature (℃)
1
-40±3℃
2
Room Temperature
3
85±2℃
4
Room Temperature
Number of cycles
Mounting method
Recovery
Duration (min.)
30±3
Within 3
30±3
Within 3
: 100
: Soldering onto PC board
: 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
10. Resistance to Humidity (steady state)
Specified Value
Appearances
Impedance change
: No significant abnormality
: Within ±30% of the initial value
Test Methods and
Remarks
Temperature
Humidity
Duration
Mounting method
Recovery
: 40±2℃
: 90 to 95% RH
: 500+24/-0
: Soldering onto PC board
: 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
11. Loading under Damp Heat
Specified Value
Appearance
Impedance change
Test Methods and
Remarks
Temperature
Humidity
Applied current
Duration
Mounting method
Recovery
No significant abnormality
Within ±30% of the initial value
: 40±2℃
: 90 to 95%RH
: Rated current
: 500+24/-0 hrs
: Soldering onto PC board
: 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
12. High Temperature Loading Test
Specified Value
Appearance
Impedance change
: No significant abnormality
: Within ±30% of the initial value
Test Methods and
Remarks
Temperature
Duration
Applied current
Mounting method
Recovery
:
:
:
:
:
85±2℃
500+24/-0 hrs
Rated current
Soldering onto PC board
2 to 3 hrs of recovery under the standard condition after the removal from test chamber.
13. Bending Strength
Specified Value
Appearance : No mechanical damage.
Warp
Testing board
Thickness
: 2mm
: Glass epoxy-resin substrate
: 0.8mm
Test Methods and
Remarks
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_reli_e-E04R01
14. Adhesion of Electrode
Specified Value
No separation or indication of separation of electrode.
Applied force
Duration
: 5N
: 10 sec.
Test Methods and
Remarks
Note on standard condition: "standard condition" referred to herein is defined as follows:
5 to 35℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure.
When there are questions concerning measurement results:
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity and 86 to 106kPa of air
pressure. Unless otherwise specified, all the tests are conducted under the "standard condition."
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_reli_e-E04R01
CHIP BEAD INDUCTORS FOR POWER LINE (FB SERIES M TYPE)
■PRECAUTIONS
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
◆Rated current
1. Rated current of this product is shown in this catalogue, but please be sure to have the base board designed with adequate inspection in
case of the generation of heat becomes high within the rated current range when the base board is in high resistance or in bad heating
conditions.
2. PCB Design
Precautions
◆Land pattern design
1. Please refer to a recommended land pattern.
3. Considerations for automatic placement
Precautions
Technical
considerations
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
◆Reflow soldering
1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering
heat, etc. sufficiently.
◆Preheating when soldering
Heating : The temperature difference between soldering and remaining heat should not be greater than 150℃.
Cooling : The temperature difference between the components and cleaning process should not be greater than 100℃.
◆Recommended conditions for using a soldering iron
Put the soldering iron on the land-pattern.
Soldering iron's temperature - Below 350℃
Duration - 3 seconds or less
The soldering iron should not directly touch the inductor.
◆Wave, Reflow, Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
【Recommended reflow condition】
Technical
considerations
◆Preheating when soldering
1. There is a case that products get damaged by a heat shock.
◆Recommended conditions for using a soldering iron
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_prec_e-E05R01
5. Handling
Precautions
Technical
considerations
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Setting PC boards
1. When setting a chip mounted base board, please make sure that there is no residual stress to the chip by distortion in the board or at
screw part.
◆Breakaway PC boards (splitting along perforations)
1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the
board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Setting PC boards
1. There is a case that a characteristic varies with residual stress.
◆Breakaway PC boards (splitting along perforations)
1. Planning pattern configurations and the position of products should be carefully performed to minimize stress.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
6. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
・Recommended conditions
Ambient temperature -5~40℃
Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, inductors should be used within 6 months from the time of delivery.
Technical
considerations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipbeads_prec_e-E05R01