GYSFFMAXB

15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB GPS Module SMD type (without Antenna) GYSFFMAXB Data Report 1/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Document constituent list Control name General Items Absolute maximum ratings Electrical characteristics Electrical characteristics Electrical characteristics Circuit schematic Outline / Appearance Pin Layout Handling Precaution Packaging Specification Control No. HD-AG-A HD-AM- A HD-AE- A HD-AE- B HD-AE- C HD-MC- A HD-AD- A HD-BA-A HQ-BA-523 HD-BB-A Document Page 1/4 - 4/4 1/1 1/4 - 4/4 1/1 1/1 1/1 1/3 - 3/3 1/2 - 2/2 1/3 - 3/3 1/3 - 3/3 Rev. record 09-May-2012 Ver.1.0 24-May-2012 Ver.1.1 Change Operating and Storage Temperature Range. 17-Jul-2012 Ver.1.2 Change Module P/N 12-Oct-2012 Ver.1.3 Change Icc _bk1 max 60uA (on page 8) 30-Jan-2013 Ver1.4 Change description(29Pin, on Page 19) 28-Nov-2013 Ver1.5 Change description(27Pin, on Page 19) 15-Mar-2015 Ver1.6 Change description(on page18,19) Change Handling precaution(on page 20,21,22) 2/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AG-A (1/4) Control name General Items (1)Scope This specification (“Specification”)applies to the hybrid IC “ GYSFFMAXB ”for use GPS module(“ Product”) manufacture by TAIYO YUDEN Co., Ltd.(“TAIYO YUDEN”) Please be noted that the product code shall be changed in mass production stage. 1)User’s code : GYSFFMAXB (Please state this code to order this product.) 2)Function・Features :
GPS Module（L1：1575.42MHz C/A code）
22 tracking / 66 acquisition – channel GPS receiver
12 multi-tone Active Interference Canceller（AIC）
Support multi-GNSS, QZSS, SBAS（WAAS / EGNOS / MSAS / GAGAN ）
Additional Features:（to be supported with firmware change）  AlwaysLocateTM Advanced location awareness technology  EPOTM / HotStillTM orbit prediction  EASYTM self-generation orbit prediction  Logger function support
Interface: UART
Ultra Low Power Consumption
Embedded High-performance electrical parts:LNA, TCXO, RTC, SAW_FL 3)Application : General Consumer Devices 4)Structure: Hybrid IC loaded with silicon ＆ GaAs monolithic semiconductor Propriety of Pb free Packaging by customer（thermal resistance） ：Available 5)Outline : 10.0mm(typ)×10.8mm(typ)×2.05mm(max) 46 Pin Leadless chip-carrier 6)Marking : Parts Name & Lot Number 7)Packing ：Tape & Reel（MP） 3/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AG-A (2/4) Control name General Items 8) Notes: a. Limitation of Warranty i) TAIYO YUDEN provide warranties only if the Products is operated under the condition set forth in this Specification. Please note that TAIYO YUDEN shall not be liable for any defect and/or malfunction arising from use of the Product under the terms and conditions other than the operating conditions hereof. In addition when this Product is used under environmental conditions such as over voltage which are not guaranteed, it may be destroyed in short mode. To ensure the security of customer’s product, please add an extra fuse or/and a protection circuit for over voltage. ii) This Product is designed for use in products which comply with GPS Specifications. TAIYO YUDEN disclaims and is not responsible for any liability concerning infringement by this Product under any intellectual property right owner by third party in case the customer uses this Product in any product which does not comply with GPS Specifications (the ”non-complying products”). Furthermore, TAIYO YUDEN warrants only that this Product complies with this Specification and does not grant any other warranty including warranty for application of the non-complying products. iii) In some cases, TAIYO YUDEN may use replacements as component parts of Products. Such replacement shall apply only to component part of Products, which TAIYO YUDEN deems it possible to replace or substitute according to (i)scope of Warranty provided in this specification(e.g. Electric Characteristics, Outline, Dimension, Conditions of Use, Reliability Tests, Official Standard(Type Approvals etc.))and (ii)Quality of Products. TAIYO YUDEN also ensure traceability of such replacement on production lot basis. b. Introduction for Use(CAUTION) i) Because Product is not designed for radiation durability, please refrain from exposing product to radiation in the use. ii) Communication between this Product and other might not be established nor maintained depending upon radio environment or operating condition of this Product and other products with GPS technology. iii) This Product mentioned in this Specification is manufactured for use in general consumer devices. Before using this Product in any special equipment( such as medical equipment, space equipment, air craft, disaster prevention equipment),where higher safety and reliability are duly required, the applicability and suitability of this Product must be fully evaluated by the safety function of this Product even for use in general electronics equipment shall be thoroughly made and when necessary, a protective circuit shall be added in design stage, all at the customer’s sole risk. 4/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AG-A (3/4) Control name General Items c. Terms of Support i) Customers are requested to fully check and confirm by the start of mass production of this Product that(1)no bug, defect or other failure is included in firmware incorporated in this Product(“Incorporated Software”),(2)no bug, defect or other failure arising from installation of this Product in which is contained Incorporated Software into customer’s product is included in Incorporated Software, and that Incorporated Software fully meets customer’s intended use, although TAIYO YUDEN sufficiently inspects or verifies quality of Incorporated Software. ii) Please note that TAIYO YUDEN is not responsible for any failure arising out of bugs or Defects which you have not found in Incorporated Software prior to reaching an agreement of this Specification between customer and TAIYO YUDEN(including the bugs or defects found after customer’s acceptance and evaluation). iii) In the case of customer requests TAIYO YUDEN to customize the hardware or firmware of this product in order to meet such customer’s specific needs, TAIYO YUDEN will make commercially reasonable effort to modify such hardware or software at customer’s expense; provide however, the customer is kindly requested to agrees it doesn’t mean that TAIYO YUDEN has obligations to do so even in the case it is technically difficult for TAIYO YUDEN. iⅴ) Any failure arising out of this Product will be examined by TAIYO YUDEN regardless of before or after mass production. Customer agree that once such failure is turned out not to be responsible for TAIYO YUDEN after aforesaid examination, some of the technical support shall be conducted by TAIYO YUDEN at customer’s expense; provided however, exact cost of this technical support can be agreed though the negotiation by the parties. v) Do not alert hardware and/or firmware of this Product. Please note that TAIYO YUDEN shall not be liable for any problem if it is caused by Customer’s alteration of Hardware or/and Firmware without Taiyo Yuden’s prior approvals. 5/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AG-A (4/4) Control name General Items d. Cautions for Export Control This Product may be subject to governmental approvals, consents, licenses, authorizations, Declarations, filings, and registrations for export or re-export of the Product, required By Japanese Foreign Exchange and Foreign Trade Law(including related laws and regulations) and/or any other country’s applicable laws or regulations related to export control. In case you will export or re-export this Product, you are strongly recommended to check and confirm, before exporting or re-exporting, necessary procedures for export or re-export of this Products which is required by applicable laws and regulations, and if necessary, you have to obtain necessary and appropriate approvals or licenses from governmental authority at your own risk and expense. e. Warranty TAIYO YUDEN warrants only that this Product is in conformity with this Specification for One year after purchase and shall in no event give any other warranty. The warranty period shall be one year. f. Items mentioned in the specification Any question arising from this specification shall be solved through mutual discussion by the parties hereof. 6/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AM-A 1.Maximum rating Item Input voltage Control name Absolute maximum ratings (1/1) Symbol VDD3V3 VDD_BACKUP RESET, GIO/EINT, RX 2.Recommendation operating range Item Symbol VDD3V3 Operating input voltage VDD_BACKUP Supply voltage VDD3V3 ripple and spike VDD_BACKUP noise Operating temperature Topr range Storage temperature Tstg range MIN -0.3 -0.3 TYP -0.3 MIN 3.0 2.0 MAX 4.3 4.3 Unit V Condition Ta=25degrees-C 3.6 TYP 3.3 3.3 MAX 4.3 4.3 Unit Condition V 40 mV/p-p 40 -30 25 85 degrees -C Humidity Note1 =40%RH -30 25 85 degrees -C Humidity Note2 =40%RH Notes: 1. Operating temperature range is set to satisfy products electrical characteristics in the short terms. In terms of product life cycle when it is used in condition of varying from TYP standard in the long term, please refer to the reliability condition. 2. Storage temperature range is the condition for transportation and storage in temporary. 7/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AE-A (1/4) Control name Electrical characteristics Electrical characteristics DC Specifications The Specification applies for Topr.= 25 degrees-C, voltage=typical No. 1 2 3 4 Parameter Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage 5 Current MAIN 6 Current BK Condition Rx, GIO/EINT, RESET Tx, GIO/EINT VDD3V3 Current Consumption (Average) VDD3V3_BACKUP Current Consumption Symbol VIL18 VIH18 VOL18 VOH18 Min. -0.18 1.5 -0.18 1.4 Typ. - Max. 0.4 1.98 0.4 2.13 Unit V V V V Icc_Ac - 19 35 mA Icc_Tr - 16 35 mA Icc _bk1 - 6 60 uA Icc _bk2 - 24 200 uA Remark IO=1.8V IO =1.8V IO=1.8V IO =1.8V Acquisition (EASY enable) Tracking (EASY enable) Backup (VDD3V3=0 V) Other mode Note: Please note that these electrical characteristics were measured under Taiyo Yuden evaluation environment. 8/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AE-A (2/4) Control name Electrical characteristics AC Specifications The Specification applies for Topr .=25 degrees-C No . 1 2 3 4 5 6 7 8 Parameter Condition Symbol Min T1 1000 ms T2 100 ms Time from VDD3V3_BACKUP rise to VDD3V3 rise Time from VDD3V3 rise to RESET rise Time from RESET High to Module Ready Typ T3 RESET Pulse Width Time from VDD3V3 fall (0.5V) to VDD3V3_BACKUP fall VDD3V3 fall time from 3.0V to 0.5V Time from RESET Low to VDD3V3 fall Inrush Current VDD3V3 Max 1500 Unit ms T4 10 ms T5 20 ms T6 100 ms T7 10 ms Icc_rush - - 400 Remark mA After power on Note1 VDD3V3_BACKUP T1 VDD3V3 T2 RESET T3 ACTIVE UART I/F Power on timing TX/RXD T4 RESET RESET Pulse Width Note: UART I/F is not active during the assertion of RESET pin. 9/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AE-A Control name Electrical characteristics (3/4) T5 VDD3V3_BACKUP T6 VDD3V3 2.8V 0.5V T7 RESET UART I/F ACTIVE Power-off Timing Recommended Parts for VDD3V3 Power Supply XC6221（TOREX）(without discharge function type, Output Voltage3.3V) Note1 Inrush current test circuit 10/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AE-A (4/4) Control name Electrical characteristics UART Interface AC Specifications The Specification applies for Ta=25 degrees-C LSB UART TX/RXD Start bit Data bits (one byte) Baud Rate Required (bps) 4800 9600 14400 19200 38400 57600 115200 230400 460800 921600 End bit Programmed Baud Rate (bps) 4803 9606 14208 19212 38423 56835 113673 227353 454741 909583 Default 115200bps 11/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AE-B (1/1) Control name Electrical characteristics RF Specifications The Specification applies for Topr.=25 degrees-C Parameter No Symbol Spec 1 2 Frequency Intermediate frequency Fc IF 3 Image Rejection Ratio IRR 30 dB 4 5 VCO Oscillation Frequency Noise Figure Fosc NF Hs1 Ws1 Cs1 Ts1 Ht1 Wt1 Ct1 Ha1 Wa1 Ca1 3142.656 1.0 -162 -146 -146 -164 1.0 34 42 2 2 2 MHz dB Sensitivity 1 7 TTFF 1 8 Accuracy 1 Max Unit Typ 1575.42 4.092 6 Min Remark MHz C/A code MHz Hot start sensitivity Warm start sensitivity dBm Cold start sensitivity Tracking sensitivity Hot start @-135dBm Note1 sec Warm start@-135dBm Note2 Cold start @-135dBm Note3 Hot start @-135dBm m Warm start@-135dBm Cold start @-135dBm Note1 Hot start : Re-start in state with Data of Almanac, Ephemeris, and time information. Note2 Warm start : Re-start in state with Data of Almanac. Note3 Cold start : Start when there is not all information. 12/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AE-C (1/1) Control name Electrical characteristics Firmware 1. Embedded Firmware： Example for Firmware Name e.g 20091225 _TY_Module_A1.20P(C29)_00.bin 2. MTK NMEA Packet Format Attachment Sheet： Please refer to ”MTK NMEA Packet User Manual”. 13/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-MC-A Module Block Diagram ANT (1/1) Control name Circuit Schematic Module Saw LNA MT3339 NMEA Data Host X’tal UART TCXO Power supply Reference : Peripheral Circuits （This Peripheral Circuits is reference only. You are requested to fully check and confirm by the start of mass production of this Product.) Pin layout details, please refer to page 18-19. 14/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AD-A Control name Outline/Appearance (1/3) Outline 10.0 +/- 0.2 #1 Marking Unit:mm 21 13 12 22 11 23 44 45 43 46 2 32 1 33 42 34 < Bottom View > 15/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AD-A (2/3) Control name Outline/Appearance Recommended Land Pattern ( same as Module Land form) Unit:mm 10.0 4.2 4.2 6.4 ( Pitch 0.8 x 8 ) 38- 0.5x1.0 C0.5 2.5 0.6 2.5 4.3 1.0 4.3 < Top View > 16/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-AD-A (3/3) Control name Outline/Appearance Recommended Metal Masking(Solder Masking) URL pattern Unit： ：mm 10.0 4.2 4.2 6.4 ( Pitch 0.8 x 8 ) 38- 0.5x1.0 C0.35 2.0 1.1 2.0 4.3 1.0 4.3 < Top View > 17/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-BA-A Control name Pin Layout (1/2) Pin Layout (Top View) Descriptions No. Pin Name Type Block 1 2 3 4 5 6 7 GND ANT GND VDD3V3 NC NC NC Power RF Power Power GND RF GND RF & Digital - I I - GND RF_IN Antenna port GND Power Supply voltage 3.3V Never to connect Never to connect Never to connect 8 9 10 11 12 13 GND NC GND NC GND NC Power GND GND GND - - GND Never to connect GND Never to connect GND Never to connect Power Analog I Debug CLK O Supply Voltage to RTC LDO. Back-up power supply ＊ at all times “ON” by button battery Never to connect Never to connect RTC 32kHz clock output default no output, controlled by S/W build.(Optional) *Never to connect in case of an unnecessary 14 VDD3V3_BACKUP 15 16 17 NC NC 32KHZ_OUT Power Power I/O Description Main power supply 18/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HD-BA-A Control name Pin Layout (2/2) No. Pin Name Type 18 19 20 21 22 23 24 NC NC NC NC GND NC NC 25 UART_RXD CMOS UART 26 UART_TXD CMOS UART 27 TIMER CMOS CLK 28 NC 29 1PPS 30 31 NC NC 32 RESET CMOS Digital I 33 34 35 36 37 38 39 40 41 42 43 44 45 46 GND NC NC GND GND GND GND GND GND GND GND GND GND GND Power GND GND GND GND GND GND GND GND GND GND GND GND - Power Block I/O Description GND - Never to connect. Never to connect. Never to connect. Never to connect. GND Never to connect. Never to connect. Serial data input for the UART Interface. I Internal 75kΩpull up. Serial data output for the UART Interface. O Internal 75kΩpull up. In Backup mode, count and output time interval. Open drain output. It doesn’t PULL UP in IC. O Prefer to PULL Up outside of IC *Please Connect to GND in case of an unnecessary. - Never to connect. 1pps signal output I/O (Default: Duty cycle 0.1/ Timing: 3DFix) - Never to connect. - Never to connect. CMOS Digital - Power Power Power Power Power Power Power Power Power Power Power - RESET terminal, active LOW Internal 75kΩpull up GND Never to connect. Never to connect. GND GND GND GND GND GND GND GND GND GND GND 19/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HQ-BA-523 (1/2) Control name Handling Precaution This specification describes desire and conditions especially for mounting. Desire／Conditions (1) Environment conditions for use and storage 1. Store the components in an environment of < 40deg-C/90％ ％RH if they are in a moisture barrier bag packed by TAIYO YUDEN. 2. Keep the factory ambient conditions at < 30deg-C/60％ ％RH . 3. Store the components in an environment of < 25±5deg-C/10%RH after the bag is opened. (The condition is also applied to a stay in the manufacture process). (2) Conditions for handling of products Make sure all of the moisture barrier bags have no holes, cracks or damages at receiving. If an abnormality is found on the bag, its moisture level must be checked in accordance with 2 in (2). Refer to the label on the bag. 1.All of the surface mounting process (reflow process) must be completed in 12 months from the bag sea date. 2. Make sure humidity in the bag is less than 10%RH immediately after open, using a humidity indicator card sealed with the components. 3. All of the surface mounting process (reflow process including rework process) must be completed in 168 hours after the bag is opened (inclusive of any other processes). 4. If any conditions in (1) or condition 2 and 3 in (2) are not met, bake the components in accordance with the conditions at 125deg-C 24hours 5. As a rule, baking the components in accordance with conditions 4 in (2) shall be once. 20/24 TAIYO YUDEN 15-Mar.-2015 Ver.1.6 TAIYO YUDEN GYSFFMAXB Control No. HQ-BA-523 (2/2) Control name Handling Precaution 6. Since semi-conductors are inside of the components, they must be free from static electricity while handled.(