Notice for TAIYO YUDEN Products
[ For General Electronic Equipment ]
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2018. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully
before practical application or use of our products.
Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or
equipment incorporating our products, which are caused under the conditions other than those specified in this
catalog or individual product specification sheets.
■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification
sheets are available.
■ Please conduct validation and verification of our products in actual condition of mounting and operating
environment before using our products.
■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA
equipment, home electric appliances, office equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be
sure to contact TAIYO YUDEN for further information before using the products for any equipment which may
directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment,
disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information
network equipment including, without limitation, telephone exchange, and base station).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g.,
aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control
equipment, undersea equipment, military equipment).
*Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g.,
in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN.
Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment.
When our products are used even for high safety and/or reliability-required devices or circuits of general electronic
equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to
install a protection circuit as necessary.
Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way
responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog
for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above.
■ Information contained in this catalog is intended to convey examples of typical performances and/or applications
of our products and is not intended to make any warranty with respect to the intellectual property rights or any
other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights.
■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and
TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products.
Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in
accordance with such agreement.
■ The contents of this catalog are applicable to our products which are purchased from our sales offices or
authorized distributors (hereinafter“TAIYO YUDEN’
s official sales channel”). Please note that the contents of this
catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’
s official sales
channel.
■ Caution for Export
Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export
Administration Regulations”
,“Foreign Exchange and Foreign Trade Control Law”of Japan, and other applicable
regulations. Should you have any questions on this matter, please contact our sales staff.
19
MULTILAYER CERAMIC CAPACITORS
MULTILAYER CERAMIC CAPACITORS
WAVE
WAVE
REFLOW
REFLOW
■PARTS NUMBER
J M K
① ② ③
3
1 6
④
CERAMIC CAPACITORS
①Rated voltage
Code
P
A
J
L
E
T
G
U
H
Q
S
X
②Series name
Code
M
V
W
△
⑤
B
J
1
⑥
0 6
⑦
③End termination
Code
K
S
Rated voltage[VDC]
2.5
4
6.3
10
16
25
35
50
100
250
630
2000
A
End termination
Plated
Cu Internal Electrodes (For High Frequency)
④Dimension(L×W)
Dimensions
(L×W)[mm]
021
0.25× 0.125
042
0.4 × 0.2
063
0.6 × 0.3
1.0 × 0.5
105
0.52× 1.0 ※
1.6 × 0.8
107
0.8 × 1.6 ※
2.0 × 1.25
212
1.25× 2.0 ※
316
3.2 × 1.6
325
3.2 × 2.5
432
4.5 × 3.2
Note : ※LW reverse type(□WK) only
Type
Series name
Multilayer ceramic capacitor
Multilayer ceramic capacitor for high frequency
LW reverse type multilayer capacitor
⑤Dimension tolerance
Code
Type
△
ALL
063
105
107
△=Blank space
M L - T △
⑧ ⑨ ⑩ ⑪ ⑫
L[mm]
Standard
W[mm]
Standard
0.6±0.05
1.0±0.10
1.6+0.15/-0.05
0.3±0.05
0.5±0.10
0.8+0.15/-0.05
212
2.0+0.15/-0.05
1.25+0.15/-0.05
316
3.2±0.20
1.6±0.20
325
063
105
3.2±0.30
0.6±0.09
1.0+0.15/-0.05
2.5±0.30
0.3±0.09
0.5+0.15/-0.05
107
1.6+0.20/-0
0.8+0.20/-0
212
2.0+0.20/-0
1.25+0.20/-0
316
105
105
008004
01005
0201
0402
0204
0603
0306
0805
0508
1206
1210
1812
T[mm]
Standard
0.3±0.05
0.5±0.10
0.8+0.15/-0.05
0.45±0.05
0.85±0.10
1.25+0.15/-0.05
0.85±0.10
1.6±0.20
2.5±0.30
0.3±0.09
0.5+0.15/-0.05
0.45±0.05
0.8+0.20/-0
0.45±0.05
0.85±0.10
1.25+0.20/-0
1.6±0.30
0.5+0.20/-0
0.5+0.30/-0
△= Blank space
B
C
E
EIA(inch)
3.2±0.30
1.6±0.30
1.0+0.20/-0
0.5+0.20/-0
1.0+0.30/-0
0.5+0.30/-0
Note: cf. STANDARD EXTERNAL DIMENSIONS
⑥Temperature characteristics code
■High dielectric type(Excluding Super low distortion multilayer ceramic capacitor)
Applicable
Temperature
Code
Ref. Temp.[℃]
Capacitance change
standard
range[℃]
JIS
B
-25~+ 85
20
±10%
EIA
X5R
-55~+ 85
25
±15%
B7
EIA
X7R
-55~+125
25
±15%
C6
EIA
X6S
-55~+105
25
±22%
C7
EIA
X7S
-55~+125
25
±22%
LD(※)
EIA
X5R
-55~+ 85
25
±15%
BJ
Note : ※.LD Low distortion high value multilayer ceramic capacitor
Capacitance
tolerance
±10%
±20%
±10%
±20%
±10%
±20%
±10%
±20%
±10%
±20%
±10%
±20%
Tolerance
code
K
M
K
M
K
M
K
M
K
M
K
M
△= Blank space
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
12
19
■Temperature compensating type
Applicable
Code
standard
CG
UJ
UK
C0G
JIS
UJ
EIA
JIS
EIA
JIS
U2J
UK
U2K
SL
Ref. Temp.[℃]
Capacitance change
-55~+125
25
0±30ppm/℃
-55~+125
-55~+125
-55~+125
-55~+125
⑥Series code
・Super low distortion multilayer ceramic capacitor
Code
Series code
SD
Standard
・Medium-High Voltage Multilayer Ceramic Capacitor
Code
Series code
SD
Standard
⑦Nominal capacitance
Code
(example)
0R5
010
100
101
102
103
104
105
106
107
Note : R=Decimal point
⑧Capacitance tolerance
Code
A
B
C
D
F
G
J
K
M
Z
Nominal capacitance
0.5pF
1pF
10pF
100pF
1,000pF
10,000pF
0.1μF
1.0μF
10μF
100μF
Capacitance tolerance
±0.05pF
±0.1pF
±0.25pF
±0.5pF
±1pF
±2%
±5%
±10%
±20%
+80/-20%
20
25
20
25
20
Capacitance
tolerance
±0.05pF
±0.1pF
±0.25pF
±0.5pF
±5%
±0.25pF
±0.5pF
±5%
Tolerance
code
A
B
C
D
J
C
D
J
-750±250ppm/℃
±0.25pF
C
+350~-1000ppm/℃
±5%
J
-750±120ppm/℃
⑨Thickness
Code
K
H
E
C
D
P
T
K
V
W
A
D
F
G
L
N
Y
M
⑩Special code
Code
-
⑪Packaging
Code
F
T
P
R
W
⑫Internal code
Code
△
CERAMIC CAPACITORS
SL
EIA
Temperature
range[℃]
Thickness[mm]
0.125
0.13
0.18
0.2
0.3
0.45(107type or more)
0.5
0.8
0.85(212type or more)
1.15
1.25
1.6
1.9
2.0 max
2.5
Special code
Standard
Packaging
φ178mm Taping (2mm pitch)
φ178mm Taping (4mm pitch)
φ178mm Taping (4mm pitch, 1000 pcs/reel)
325 type(Thickness code M)
φ178mm Taping (2mm pitch)105type only
(Thickness code E,H)
φ178mm Taping(1mm pitch)021/042type only
Internal code
Standard
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
c_mlcc_e-E07R01
13
■STANDARD EXTERNAL DIMENSIONS
W
Type( EIA )
T
e
Dimension [mm]
T
0.125±0.013
0.125±0.013
□MK021(008004)
□VS021(008004)
L
0.25±0.013
0.25±0.013
W
0.125±0.013
0.125±0.013
□MK042(01005)
0.4±0.02
0.2±0.02
0.2±0.02
L
□VS042(01005)
0.4±0.02
0.2±0.02
0.2±0.02
□MK063(0201)
0.6±0.03
0.3±0.03
0.3±0.03
L
CERAMIC CAPACITORS
□MK105(0402)
1.0±0.05
0.5±0.05
□VK105(0402)
□WK105(0204)※
1.0±0.05
0.52±0.05
0.5±0.05
1.0±0.05
□MK107(0603)
1.6±0.10
0.8±0.10
□WK107(0306)※
0.8±0.10
1.6±0.10
□MK212(0805)
2.0±0.10
1.25±0.10
□WK212(0508)※
1.25±0.15
2.0±0.15
□MK316(1206)
3.2±0.15
1.6±0.15
□MK325(1210)
3.2±0.30
2.5±0.20
□MK432(1812)
4.5±0.40
3.2±0.30
W
T
e
※ LW reverse type
0.13±0.02
0.18±0.02
0.2±0.02
0.3±0.03
0.5±0.05
0.5±0.05
0.3±0.05
0.45±0.05
0.8±0.10
0.5±0.05
0.45±0.05
0.85±0.10
1.25±0.10
0.85±0.10
0.85±0.10
1.15±0.10
1.6±0.20
0.85±0.10
1.15±0.10
1.9±0.20
1.9+0.1/-0.2
2.5±0.20
2.0+0/-0.30
2.5±0.20
*1
K
K
C
D
C
P
T
H
E
C
P
V
W
P
K
A
V
K
D
G
D
D
F
L
D
F
N
Y
M
Y
M
e
0.0675±0.0275
0.0675±0.0275
0.1±0.03
0.1±0.03
0.15±0.05
0.25±0.10
0.25±0.10
0.18±0.08
0.35±0.25
0.25±0.15
0.5±0.25
0.3±0.2
0.5+0.35/-0.25
0.6±0.3
0.6±0.4
0.9±0.6
Note : ※. LW reverse type, *1.Thickness code
■STANDARD QUANTITY
Type
EIA(inch)
Dimension
021
008004
[mm]
0.125
042
01005
0.2
063
0201
0.3
105
0402
0.13
0.18
0.2
0.3
0.5
0204 ※
107
0603
0306 ※
212
0805
0508 ※
316
1206
325
1210
432
1812
0.30
0.45
0.8
0.50
0.45
0.85
1.25
0.85
0.85
1.15
1.6
0.85
1.15
1.9
2.0 max
2.5
2.0 max
2.5
Code
K
C
D
P
T
H
E
C
P
V
W
P
K
A
V
K
D
G
D
D
F
L
D
F
N
Y
M
Y
M
Standard quantity[pcs]
Paper tape
Embossed tape
-
50000
-
40000
15000
-
-
-
20000
15000
20000
15000
-
-
10000
-
4000
-
-
4000
4000
-
-
4000
4000
-
-
3000
-
-
3000
2000
-
2000
-
-
-
1000
1000
500
Note : ※.LW Reverse type(□WK)
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
14
19
■PARTS NUMBER
・ All the Multilayer Ceramic Capacitors of the catalog lineup are RoHS Compliant.
・ Capacitance tolerance code is applied to [] of part number.
Note)
*1 We may provide X7R/X7S for some items according to the individual specification.
*2 The exchange of individual specification is necessary depending on the application and circuit condition. Please contact TAIYO YUDEN sales channels.
*3 The size standard should look at ④Dimension, ⑤Dimension tolerance, and ⑨Thickness, and STANDARD EXTERNAL DIMENSIONS.
Multilayer Ceramic Capacitors (High dielectric type)
●021TYPE
【Temperature Characteristic BJ : X5R(-55~+85℃)】 0.125mm thickness(K)
Part number 1
Part number 2
Temperature
characteristics
X5R
X5R
X5R
X5R
X5R
X5R
X5R
16
6.3
4
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
220
470
1000
2200
4700
0.01
0.022
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
10
10
10
10
10
10
10
p
p
p
p
p
μ
μ
HTLT
Rated voltage x %
150
150
150
150
150
150
150
Thickness*3 [mm]
0.125±0.013
0.125±0.013
0.125±0.013
0.125±0.013
0.125±0.013
0.125±0.013
0.125±0.013
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
●042TYPE
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 0.2mm thickness(C)
Part number 1
Part number 2
EMK042 BJ101[]C-W
EMK042 BJ151[]C-W
EMK042 BJ221[]C-W
EMK042 BJ331[]C-W
EMK042 BJ471[]C-W
EMK042 BJ681[]C-W
EMK042 BJ102[]C-W
EMK042 BJ152[]C-W
EMK042 BJ222[]C-W
EMK042 BJ332[]C-W
EMK042 BJ472[]C-W
EMK042 BJ682[]C-W
EMK042 BJ103[]C-W
LMK042 BJ101[]C-W
LMK042 BJ151[]C-W
LMK042 BJ221[]C-W
LMK042 BJ331[]C-W
LMK042 BJ471[]C-W
LMK042 BJ681[]C-W
LMK042 BJ102[]C-W
LMK042 BJ152[]C-W
LMK042 BJ222[]C-W
LMK042 BJ332[]C-W
LMK042 BJ472[]C-W
LMK042 BJ682[]C-W
LMK042 BJ103[]C-W
JMK042 BJ152[]C-W
JMK042 BJ222[]C-W
JMK042 BJ332[]C-W
JMK042 BJ472[]C-W
JMK042 BJ682[]C-W
JMK042 BJ103[]C-W
JMK042 BJ223[]C-W
JMK042 BJ473[]C-W
JMK042 BJ104[]C-W
AMK042 BJ473[]C-W
AMK042 BJ104[]C-W
Rated voltage
[V]
Temperature
characteristics
16
B
10
B
6.3
4
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
100
150
220
330
470
680
1000
1500
2200
3300
4700
6800
0.01
100
150
220
330
470
680
1000
1500
2200
3300
4700
6800
0.01
1500
2200
3300
4700
6800
0.01
0.022
0.047
0.1
0.047
0.1
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
5
5
5
5
5
5
5
10
10
10
10
10
10
5
5
5
5
5
5
5
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
100
150
220
330
470
680
1000
100
150
220
330
470
680
1000
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
5
5
5
5
5
5
5
5
5
5
5
5
5
5
p
p
p
p
p
p
p
p
p
p
p
p
μ
p
p
p
p
p
p
p
p
p
p
p
p
μ
p
p
p
p
p
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
200
200
200
200
200
200
200
150
150
150
150
150
150
200
200
200
200
200
200
200
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
Thickness*3 [mm]
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
CERAMIC CAPACITORS
EMK021 BJ221[]K-W
EMK021 BJ471[]K-W
EMK021 BJ102[]K-W
JMK021 BJ222[]K-W
JMK021 BJ472[]K-W
JMK021 BJ103[]K-W
AMK021 BJ223MK-W
Rated voltage
[V]
【Temperature Characteristic B7 : X7R(-55~+125℃)】 0.2mm thickness(C)
Part number 1
EMK042 B7101[]C-W
EMK042 B7151[]C-W
EMK042 B7221[]C-W
EMK042 B7331[]C-W
EMK042 B7471[]C-W
EMK042 B7681[]C-W
EMK042 B7102[]C-W
LMK042 B7101[]C-W
LMK042 B7151[]C-W
LMK042 B7221[]C-W
LMK042 B7331[]C-W
LMK042 B7471[]C-W
LMK042 B7681[]C-W
LMK042 B7102[]C-W
Part number 2
Rated voltage
[V]
16
10
Temperature
characteristics
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
p
p
p
p
p
p
p
p
p
p
p
p
p
p
HTLT
Rated voltage x %
200
200
200
200
200
200
200
200
200
200
200
200
200
200
Thickness*3 [mm]
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
15
■PARTS NUMBER
●063TYPE
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 0.3mm thickness(P)
Part number 1
Part number 2
CERAMIC CAPACITORS
UMK063 BJ101[]P-F
UMK063 BJ151[]P-F
UMK063 BJ221[]P-F
UMK063 BJ331[]P-F
UMK063 BJ471[]P-F
UMK063 BJ681[]P-F
UMK063 BJ102[]P-F
UMK063 BJ152[]P-F
UMK063 BJ222[]P-F
UMK063 BJ332[]P-F
UMK063 BJ472[]P-F
UMK063 BJ682[]P-F
UMK063 BJ103[]P-F
GMK063 BJ104[]P-F
TMK063 BJ152[]P-F
TMK063 BJ222[]P-F
TMK063 BJ332[]P-F
TMK063 BJ472[]P-F
TMK063 BJ682[]P-F
TMK063 BJ103[]P-F
TMK063 BJ223[]P-F
TMK063ABJ104[]P-F
EMK063 BJ152[]P-F
EMK063 BJ222[]P-F
EMK063 BJ332[]P-F
EMK063 BJ472[]P-F
EMK063 BJ682[]P-F
EMK063 BJ103[]P-F
EMK063 BJ223[]P-F
EMK063 BJ333[]P-F
EMK063 BJ473[]P-F
EMK063 BJ683[]P-F
EMK063 BJ104[]P-F
EMK063 BJ224[]P-F
EMK063BBJ474[]PLF
LMK063 BJ223[]P-F
LMK063 BJ333[]P-F
LMK063 BJ473[]P-F
LMK063 BJ683[]P-F
LMK063 BJ104[]P-F
LMK063 BJ224[]P-F
LMK063BBJ474[]PLF
LMK063BBJ105MPLF
JMK063 BJ223[]P-F
JMK063 BJ333[]P-F
JMK063 BJ473[]P-F
JMK063 BJ683[]P-F
JMK063 BJ104[]P-F
JMK063 BJ224[]P-F
JMK063 BJ334MP-F
JMK063 BJ474[]P-F
JMK063ABJ105[]P-F
AMK063 BJ224[]P-F
AMK063 BJ334MP-F
AMK063 BJ474[]P-F
AMK063ABJ105[]P-F
Rated voltage
[V]
Temperature
characteristics
B
50
B
B
B
B
B
B
B
B
35
25
16
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
10
B
6.3
4
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
100
150
220
330
470
680
1000
1500
2200
3300
4700
6800
0.01
0.1
1500
2200
3300
4700
6800
0.01
0.022
0.1
1500
2200
3300
4700
6800
0.01
0.022
0.033
0.047
0.068
0.1
0.22
0.47
0.022
0.033
0.047
0.068
0.1
0.22
0.47
1
0.022
0.033
0.047
0.068
0.1
0.22
0.33
0.47
1
0.22
0.33
0.47
1
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
3.5
3.5
3.5
3.5
3.5
3.5
3.5
5
5
5
5
5
5
10
5
5
5
5
5
5
7.5
10
5
5
5
5
5
5
7.5
7.5
7.5
10
10
10
10
7.5
7.5
7.5
10
10
10
10
10
7.5
7.5
7.5
10
10
10
10
10
10
10
10
10
10
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
0.1
0.1
0.033
0.047
0.068
0.1
0.22
0.47
0.022
0.033
0.047
0.068
0.1
0.22
0.47
1
0.47
1
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
10
10
7.5
7.5
10
10
10
10
7.5
7.5
7.5
10
10
10
10
10
10
10
p
p
p
p
p
p
p
p
p
p
p
p
μ
μ
p
p
p
p
p
μ
μ
μ
p
p
p
p
p
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
200
200
200
200
200
200
200
200
200
200
200
200
200
150
200
200
200
200
200
200
200
150
200
200
200
200
200
200
200
150
150
150
150
150
150
150
150
150
150
150
150
150
150
200
150
150
150
150
150
150
150
150
150
150
150
150
Thickness*3 [mm]
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.05
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.09
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.09
0.3±0.09
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.05
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.05
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
【Temperature Characteristic C6 : X6S(-55~+105℃)】 0.3mm thickness(P)
Part number 1
TMK063 C6104[]P-F
EMK063AC6104[]P-F
LMK063 C6333[]P-F
LMK063 C6473[]P-F
LMK063 C6683[]P-F
LMK063 C6104[]P-F
LMK063 C6224[]P-F
LMK063BC6474[]PLF
JMK063 C6223[]P-F
JMK063 C6333[]P-F
JMK063 C6473[]P-F
JMK063 C6683[]P-F
JMK063 C6104[]P-F
JMK063 C6224[]P-F
JMK063BC6474[]P-F
JMK063BC6105MP-F
AMK063 C6474[]P-F
AMK063AC6105[]P-F
Part number 2
Rated voltage
[V]
25
16
10
6.3
4
Temperature
characteristics
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
150
150
150
150
200
150
150
150
150
150
150
150
150
150
Thickness*3 [mm]
0.3±0.03
0.3±0.05
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.09
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.09
0.3±0.09
0.3±0.03
0.3±0.05
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
16
19
■PARTS NUMBER
【Temperature Characteristic B7 : X7R(-55~+125℃)】 0.3mm thickness(P)
Part number 1
Part number 2
Temperature
characteristics
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
50
25
16
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
100
150
220
330
470
680
1000
1500
2200
3300
4700
6800
0.01
1500
2200
3300
4700
6800
0.01
0.022
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
3.5
3.5
3.5
3.5
3.5
3.5
3.5
5
5
5
5
5
5
5
5
5
5
5
5
7.5
p
p
p
p
p
p
p
p
p
p
p
p
μ
p
p
p
p
p
μ
μ
HTLT
Rated voltage x %
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
150
Thickness*3 [mm]
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
●105TYPE
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 0.5mm thickness(V)
Part number 1
UMK105 BJ221[]V-F
UMK105 BJ331[]V-F
UMK105 BJ471[]V-F
UMK105 BJ681[]V-F
UMK105 BJ102[]V-F
UMK105 BJ152[]V-F
UMK105 BJ222[]V-F
UMK105 BJ332[]V-F
UMK105 BJ472[]V-F
UMK105 BJ682[]V-F
UMK105 BJ103[]V-F
UMK105 BJ104[]V-F
UMK105 BJ224[]V-F
UMK105ABJ474[]V-F
UMK105CBJ105MV-F
GMK105 BJ104[]V-F
GMK105ABJ105[]V-F
TMK105 BJ153[]V-F
TMK105 BJ223[]V-F
TMK105 BJ333[]V-F
TMK105 BJ473[]V-F
TMK105 BJ104[]V-F
TMK105 BJ224[]V-F
TMK105ABJ474[]V-F
TMK105 BJ105[]V-F
TMK105CBJ225[]V-F
EMK105 BJ153[]V-F
EMK105 BJ223[]V-F
EMK105 BJ333[]V-F
EMK105 BJ473[]V-F
EMK105 BJ683[]V-F
EMK105 BJ104[]V-F
EMK105 BJ224[]V-F
EMK105ABJ474[]V-F
EMK105 BJ105[]V-F
EMK105ABJ225[]V-F
LMK105 BJ104[]V-F
LMK105 BJ224[]V-F
LMK105 BJ474[]V-F
LMK105 BJ105[]V-F
LMK105 BJ225[]V-F
LMK105BBJ475MVLF
JMK105 BJ224[]V-F
JMK105 BJ474[]V-F
JMK105 BJ105[]V-F
JMK105 BJ225[]V-F
JMK105BBJ475MV-F
JMK105CBJ106MV-F
AMK105ABJ475MV-F
AMK105CBJ106MV-F
AMK105EBJ226MV-F
Part number 2
Rated voltage
[V]
50
35
25
16
10
6.3
JMK105 BJ475MV-FD
AMK105 BJ475MV-F
4
Temperature
characteristics
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
X5R*1
X5R*1
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R*1
X5R*1
X5R*1
X5R*1
X5R
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
220
330
470
680
1000
1500
2200
3300
4700
6800
0.01
0.1
0.22
0.47
1
0.1
1
0.015
0.022
0.033
0.047
0.1
0.22
0.47
1
2.2
0.015
0.022
0.033
0.047
0.068
0.1
0.22
0.47
1
2.2
0.1
0.22
0.47
1
2.2
4.7
0.22
0.47
1
2.2
4.7
10
4.7
10
22
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±20
±20
±20
±20
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3.5
10
10
10
10
5
10
3.5
3.5
3.5
3.5
5
10
10
10
10
3.5
3.5
3.5
3.5
5
5
5
10
10
10
5
5
10
10
10
10
5
10
10
10
10
10
10
10
20
p
p
p
p
p
p
p
p
p
p
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
200
200
200
200
200
200
200
200
200
150
200
150
150
150
150
150
150
200
200
150
150
150
200
200
150
150
200
200
200
200
200
150
150
200
150
150
200
150
150
150
150
150
150
150
150
150
150
150
150
150
150
Thickness*3 [mm]
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.10
0.5+0.20/-0
0.5±0.05
0.5±0.10
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.10
0.5±0.05
0.5+0.20/-0
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.10
0.5±0.05
0.5±0.10
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5+0.15/-0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5+0.15/-0.05
0.5+0.20/-0
0.5±0.10
0.5+0.20/-0
0.5+0.30/-0
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
CERAMIC CAPACITORS
UMK063 B7101[]P-F
UMK063 B7151[]P-F
UMK063 B7221[]P-F
UMK063 B7331[]P-F
UMK063 B7471[]P-F
UMK063 B7681[]P-F
UMK063 B7102[]P-F
TMK063 B7152[]P-F
TMK063 B7222[]P-F
TMK063 B7332[]P-F
TMK063 B7472[]P-F
TMK063 B7682[]P-F
TMK063 B7103[]P-F
EMK063 B7152[]P-F
EMK063 B7222[]P-F
EMK063 B7332[]P-F
EMK063 B7472[]P-F
EMK063 B7682[]P-F
EMK063 B7103[]P-F
EMK063 B7223[]P-F
Rated voltage
[V]
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
17
■PARTS NUMBER
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 0.3mm thickness(P)
Part number 1
Part number 2
UMK105 BJ104[]P-F
TMK105 BJ103[]P-F
TMK105 BJ104[]P-F
TMK105 BJ224[]P-F
TMK105 BJ474[]P-F
EMK105 BJ474[]P-F
LMK105 BJ105[]PLF
JMK105 BJ105[]P-F
AMK105 BJ225MP-F
Rated voltage
[V]
Temperature
characteristics
50
B
25
16
10
6.3
4
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
0.1
0.01
0.1
0.22
0.47
0.47
1
1
2.2
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
10
5
10
10
10
10
10
10
10
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
0.1
0.22
0.47
1
±10, ±20
±10, ±20
±10, ±20
±20
10
10
10
10
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
0.1
0.22
0.47
1
±10, ±20
±10, ±20
±10, ±20
±20
10
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
±20
±20
±20
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
±20
±10, ±20
±10, ±20
±20
±10, ±20
±20
±10, ±20
±20
±20
±20
10
10
10
10
10
10
10
10
10
10
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
150
150
150
150
150
Thickness*3 [mm]
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
0.3±0.03
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
【Temperature Characteristic BJ : X5R(-55~+85℃)】 0.2mm thickness(C)
CERAMIC CAPACITORS
Part number 1
LMK105
JMK105
JMK105
JMK105
Part number 2
BJ104[]C-F
BJ224[]C-F
BJ474[]C-F
BJ105MC-F
Rated voltage
[V]
10
6.3
Temperature
characteristics
X5R
X5R
X5R
X5R
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
Thickness*3 [mm]
0.2±0.02
0.2±0.02
0.2±0.02
0.2±0.02
Soldering
R:Reflow
W:Wave
R
R
R
R
【Temperature Characteristic BJ : X5R(-55~+85℃)】 0.18mm thickness(E)
Part number 1
Part number 2
LMK105 BJ104[]E-R
JMK105 BJ224[]E-R
JMK105 BJ474[]E-R
AMK105 BJ105ME-R
Rated voltage
[V]
10
6.3
4
Temperature
characteristics
X5R
X5R
X5R
X5R
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
Thickness*3 [mm]
0.18±0.02
0.18±0.02
0.18±0.02
0.18±0.02
Soldering
R:Reflow
W:Wave
R
R
R
R
【Temperature Characteristic BJ : X5R(-55~+85℃)】 0.13mm thickness(H)
Part number 1
Part number 2
LMK105 BJ104MH-R
JMK105 BJ224MH-R
AMK105 BJ474MH-R
Rated voltage
[V]
10
6.3
4
Temperature
characteristics
Capacitance
[F]
X5R
X5R
X5R
0.1 μ
0.22 μ
0.47 μ
HTLT
Rated voltage x %
150
150
150
Thickness*3 [mm]
0.13±0.02
0.13±0.02
0.13±0.02
Soldering
R:Reflow
W:Wave
R
R
R
【Temperature Characteristic C6 : X6S(-55~+105℃)】 0.5mm thickness(V)
Part number 1
GMK105CC6105MV-F
TMK105AC6105[]V-F
EMK105 C6105[]V-F
EMK105CC6225MV-F
LMK105 C6105[]V-F
LMK105AC6225MV-F
JMK105 C6105[]V-F
JMK105 C6225MV-F
JMK105BC6475MV-F
AMK105BC6475MV-F
Part number 2
Rated voltage
[V]
35
25
16
10
6.3
4
Temperature
characteristics
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
Capacitance
[F]
1
1
1
2.2
1
2.2
1
2.2
4.7
4.7
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
200
150
150
150
150
200
Thickness*3 [mm]
0.5+0.20/-0
0.5±0.10
0.5±0.05
0.5+0.20/-0
0.5±0.05
0.5±0.10
0.5±0.05
0.5±0.05
0.5+0.15/-0.05
0.5+0.15/-0.05
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
18
19
■PARTS NUMBER
【Temperature Characteristic B7 : X7R(-55~+125℃)】 0.5mm thickness(V)
Part number 1
Part number 2
Temperature
characteristics
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
50
25
16
10
6.3
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
220
330
470
680
1000
1500
2200
3300
4700
6800
0.01
0.022
0.047
0.1
1500
2200
3300
4700
6800
0.01
0.022
0.047
0.1
0.22
0.022
0.047
0.1
0.22
0.022
0.047
0.1
0.22
0.47
0.22
0.47
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3.5
10
10
10
2.5
2.5
2.5
2.5
2.5
3.5
3.5
3.5
10
10
3.5
3.5
5
10
3.5
3.5
5
10
10
5
10
p
p
p
p
p
p
p
p
p
p
μ
μ
μ
μ
p
p
p
p
p
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
200
200
200
200
200
200
200
200
150
150
150
200
200
150
200
200
200
200
200
200
150
150
200
150
200
200
150
150
200
200
150
150
150
150
150
Thickness*3 [mm]
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
0.5±0.05
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
CERAMIC CAPACITORS
UMK105 B7221[]V-F
UMK105 B7331[]V-F
UMK105 B7471[]V-F
UMK105 B7681[]V-F
UMK105 B7102[]V-F
UMK105 B7152[]V-F
UMK105 B7222[]V-F
UMK105 B7332[]V-F
UMK105 B7472[]V-F
UMK105 B7682[]V-F
UMK105 B7103[]V-F
UMK105 B7223[]V-FR
UMK105 B7473[]V-FR
UMK105 B7104[]V-FR
TMK105 B7152[]V-F
TMK105 B7222[]V-F
TMK105 B7332[]V-F
TMK105 B7472[]V-F
TMK105 B7682[]V-F
TMK105 B7103[]V-F
TMK105 B7223[]V-F
TMK105 B7473[]V-F
TMK105 B7104[]V-FR
TMK105 B7224[]V-FR
EMK105 B7223[]V-F
EMK105 B7473[]V-F
EMK105 B7104[]V-F
EMK105 B7224[]V-FR
LMK105 B7223[]V-F
LMK105 B7473[]V-F
LMK105 B7104[]V-F
LMK105 B7224[]V-FR
LMK105 B7474[]V-F
JMK105 B7224[]V-F
JMK105 B7474[]V-F
Rated voltage
[V]
●107TYPE
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 0.8mm thickness(A)
Part number 1
UMK107ABJ474[]A-T
UMK107 BJ105[]A-T
UMK107BBJ225[]A-T
GMK107 BJ105[]A-T
TMK107 BJ224[]A-T
TMK107 BJ474[]A-T
TMK107 BJ105[]A-T
TMK107ABJ225[]A-T
TMK107BBJ475[]A-T
TMK107BBJ106MA-T
EMK107 BJ224[]A-T
EMK107 BJ474[]A-T
EMK107 BJ105[]A-T
EMK107 BJ225[]A-T
EMK107ABJ475[]A-T
EMK107BBJ106MA-T
LMK107 BJ224[]A-T
LMK107 BJ474[]A-T
LMK107 BJ105[]A-T
LMK107 BJ225[]A-T
LMK107 BJ475[]A-T
LMK107BBJ106[]ALT
LMK107BBJ226MA-T
JMK107 BJ225[]A-T
JMK107 BJ475[]A-T
JMK107ABJ106[]A-T
JMK107BBJ226MA-T
AMK107 BJ106MA-T
AMK107BBJ226MA-T
AMK107BBJ476MA-RE
Part number 2
Rated voltage
[V]
Temperature
characteristics
UMK107 BJ474[]A-TD
50
35
TMK107 BJ225[]A-TD
25
B
B
B
B
B
16
EMK107 BJ475[]A-TD
B
B
10
LMK107 BJ106[]ALTD
JMK107 BJ106[]A-T
AMK107 BJ226MA-T
6.3
4
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R*1
X5R*1
X5R*1
X5R
X5R
X5R
X5R*1
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
0.47
1
2.2
1
0.22
0.47
1
2.2
4.7
10
0.22
0.47
1
2.2
4.7
10
0.22
0.47
1
2.2
4.7
10
22
2.2
4.7
10
22
10
22
47
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±20
±20
±20
±20
10
10
10
5
3.5
3.5
5
10
10
10
3.5
3.5
5
10
10
10
3.5
3.5
5
10
10
10
10
10
10
10
10
10
10
20
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
200
150
150
150
150
150
200
200
150
150
150
150
200
200
200
150
150
150
150
150
150
150
150
150
150
150
Thickness*3 [mm]
0.8+0.15/-0.05
0.8±0.10
0.8+0.20/-0
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8+0.15/-0.05
0.8+0.20/-0
0.8+0.20/-0
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8+0.15/-0.05
0.8+0.20/-0
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8+0.20/-0
0.8+0.20/-0
0.8±0.10
0.8±0.10
0.8+0.15/-0.05
0.8+0.20/-0
0.8±0.10
0.8+0.20/-0
0.8+0.20/-0
Soldering
R:Reflow
W:Wave
R
R
R
R
R/W
R
R
R
R
R
R/W
R
R
R
R
R
R/W
R
R
R
R
R
R
R
R
R
R
R
R
R
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
19
■PARTS NUMBER
【Temperature Characteristic BJ : X5R(-55~+85℃)】 0.45mm thickness(K)
Part number 1
TMK107 BJ105[]K-T
EMK107 BJ105[]K-T
EMK107BBJ225[]K-T
LMK107 BJ105[]K-T
LMK107 BJ225[]K-T
LMK107BBJ475MKLT
JMK107 BJ105[]K-T
JMK107 BJ225[]K-T
JMK107 BJ475MK-T
JMK107BBJ106MK-TT
AMK107BBJ106MK-T*2
Part number 2
Rated voltage
[V]
Temperature
characteristics
25
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
16
10
LMK107 BJ475MKLTD
6.3
4
Capacitance
[F]
1
1
2.2
1
2.2
4.7
1
2.2
4.7
10
10
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
CERAMIC CAPACITORS
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±20
±20
±20
10
10
10
10
10
10
10
10
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±20
±20
±20
±20
10
5
10
10
10
5
10
10
5
10
10
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
HTLT
Rated voltage x %
150
150
150
150
150
150
150
150
150
150
150
Thickness*3 [mm]
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
【Temperature Characteristic C6 : X6S(-55~+105℃)】 0.8mm thickness(A)
Part number 1
Part number 2
TMK107BC6225[]A-T
EMK107 C6105[]A-T
EMK107BC6225[]A-T
EMK107BC6475[]A-T
EMK107BC6106MA-T
LMK107 C6105[]A-T
LMK107AC6475[]A-T
LMK107BC6106MA-T
JMK107 C6105[]A-T
JMK107 C6475[]A-T
JMK107BC6106MA-T
JMK107BC6226MA-T
AMK107AC6106MA-T
AMK107BC6226MA-T
Rated voltage
[V]
Temperature
characteristics
25
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
X6S
16
10
6.3
4
Capacitance
[F]
2.2
1
2.2
4.7
10
1
4.7
10
1
4.7
10
22
10
22
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
150
150
150
150
150
150
150
150
150
150
Thickness*3 [mm]
0.8+0.20/-0
0.8±0.10
0.8+0.20/-0
0.8+0.20/-0
0.8+0.20/-0
0.8±0.10
0.8+0.15/-0.05
0.8+0.20/-0
0.8±0.10
0.8±0.10
0.8+0.20/-0
0.8+0.20/-0
0.8+0.15/-0.05
0.8+0.20/-0
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
【Temperature Characteristic B7 : X7R(-55~+125℃)】 0.8mm thickness(A)
Part number 1
Part number 2
UMK107 B7224[]A-TR
UMK107 B7474[]A-TR
UMK107AB7105[]A-T
TMK107 B7474[]A-TR
TMK107 B7105[]A-T
EMK107 B7224[]A-T
EMK107 B7474[]A-T
EMK107 B7105[]A-T
EMK107BB7225[]A-T
LMK107 B7224[]A-T
LMK107 B7474[]A-T
LMK107 B7105[]A-T
LMK107 B7225[]A-TR
JMK107 B7224[]A-T
JMK107 B7474[]A-T
JMK107 B7105[]A-T
JMK107 B7225[]A-TR
JMK107BB7475[]A-T
Rated voltage
[V]
Temperature
characteristics
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
50
25
16
10
6.3
Capacitance
[F]
0.22
0.47
1
0.47
1
0.22
0.47
1
2.2
0.22
0.47
1
2.2
0.22
0.47
1
2.2
4.7
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
10
10
10
10
10
3.5
3.5
5
10
3.5
3.5
5
10
3.5
3.5
5
10
10
HTLT
Rated voltage x %
150
150
150
150
150
150
150
150
150
200
200
150
150
200
200
150
200
150
Thickness*3 [mm]
0.8±0.10
0.8±0.10
0.8+0.15/-0.05
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8+0.20/-0
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8±0.10
0.8+0.20/-0
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R/W
R
R
R
R/W
R
R
R
R/W
R
R
R
R
●212TYPE
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 1.25mm thickness(G)
Part number 1
UMK212 BJ104[]G-T
UMK212 BJ224[]G-T
UMK212 BJ474[]G-T
UMK212 BJ105[]G-T
UMK212ABJ225[]G-T
UMK212BBJ475[]G-T
GMK212BBJ106[]G-T
TMK212 BJ225[]G-T
TMK212ABJ475[]G-T
TMK212BBJ106MG-T
TMK212BBJ226MG-TT
EMK212 BJ225[]G-T
EMK212ABJ475[]G-T
EMK212ABJ106[]G-T
EMK212BBJ226MG-T
LMK212 BJ225[]G-T
LMK212ABJ475[]G-T
LMK212ABJ106[]G-T
LMK212BBJ226MG-T
LMK212BBJ476MG-T
JMK212ABJ475[]G-T
JMK212ABJ106[]G-T
JMK212ABJ226MG-T
JMK212BBJ476MG-T
PMK212BBJ107MG-T
Part number 2
Rated voltage
[V]
50
Temperature
characteristics
B
B
B
B
B
35
B
TMK212 BJ475[]G-T
25
EMK212 BJ475[]G-T
EMK212 BJ106[]G-T
16
LMK212 BJ475[]G-T
LMK212 BJ106[]G-T
LMK212 BJ226MG-T
10
JMK212
JMK212
JMK212
JMK212
6.3
BJ475[]G-T
BJ106[]G-T
BJ226MG-T
BJ476MG-T
2.5
X5R*1
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R*1
X5R*1
X5R
X5R
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R*1
X5R
X5R
X5R
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
0.1
0.22
0.47
1
2.2
4.7
10
2.2
4.7
10
22
2.2
4.7
10
22
2.2
4.7
10
22
47
4.7
10
22
47
100
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±20
±20
±10, ±20
±10, ±20
±20
±20
±20
3.5
3.5
3.5
5
10
10
10
5
10
10
10
5
5
10
10
5
5
10
10
10
5
10
10
10
10
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Thickness*3 [mm]
Rated voltage x %
200
1.25±0.10
200
1.25±0.10
150
1.25±0.10
150
1.25±0.10
150
1.25+0.15/-0.05
150
1.25+0.20/-0
150
1.25+0.20/-0
150
1.25±0.10
150
1.25+0.15/-0.05
150
1.25+0.20/-0
150
1.25+0.20/-0
200
1.25±0.10
150
1.25+0.15/-0.05
150
1.25+0.15/-0.05
150
1.25+0.20/-0
200
1.25±0.10
200
1.25+0.15/-0.05
200
1.25+0.15/-0.05
150
1.25+0.20/-0
150
1.25+0.20/-0
200
1.25+0.15/-0.05
200
1.25+0.15/-0.05
150
1.25+0.15/-0.05
150
1.25+0.20/-0
150
1.25+0.20/-0
Soldering
R:Reflow
W:Wave
R/W
R/W
R/W
R/W
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
20
19
■PARTS NUMBER
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 0.85mm thickness(D)
Part number 1
UMK212 BJ105[]D-TD
Rated voltage
[V]
Temperature
characteristics
50
35
B
B
TMK212 BJ225[]D-T
TMK212 BJ475[]D-TD
25
B
EMK212 BJ225[]D-T
16
EMK212 BJ106[]D-TD
B
LMK212 BJ106[]D-T
JMK212 BJ106[]D-T
JMK212 BJ226MD-T
10
6.3
4
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R*1
X5R*1
X5R
X5R
X5R*1
X5R*1
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
1
2.2
4.7
0.47
1
2.2
4.7
10
1
2.2
4.7
10
1
2.2
10
22
10
22
47
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±20
±20
10
10
10
3.5
5
5
10
10
5
5
10
10
3.5
5
10
10
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
10
10
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
±20
±20
±20
±20
±20
±20
10
10
10
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±20
10
10
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
0.1
0.22
0.47
1
2.2
1
1
2.2
4.7
1
2.2
4.7
10
1
2.2
4.7
10
10
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
3.5
3.5
3.5
10
10
3.5
3.5
10
10
3.5
10
10
10
3.5
5
10
10
10
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
200
200
150
150
150
200
200
150
150
200
200
150
150
200
150
150
Thickness*3 [mm]
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
【Temperature Characteristic BJ : X5R(-55~+85℃)】 0.45mm thickness(K)
Part number 1
TMK212BBJ225[]K-T
EMK212BBJ475[]K-T
LMK212ABJ475[]K-T
JMK212ABJ475[]K-T
JMK212ABJ106MK-T *2
Part number 2
LMK212 BJ475[]K-T
JMK212 BJ475[]K-T
JMK212 BJ106MK-T
Rated voltage
[V]
25
16
10
6.3
Temperature
characteristics
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
2.2
4.7
4.7
4.7
10
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
150
Thickness*3 [mm]
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
0.45±0.05
Soldering
R:Reflow
W:Wave
R
R
R
R
R
CERAMIC CAPACITORS
UMK212ABJ105[]D-T
UMK212BBJ225[]D-T
GMK212BBJ475[]D-T
TMK212 BJ474[]D-T
TMK212 BJ105[]D-T
TMK212ABJ225[]D-T
TMK212BBJ475[]D-T
TMK212BBJ106[]D-T
EMK212 BJ105[]D-T
EMK212ABJ225[]D-T
EMK212 BJ475[]D-T
EMK212ABJ106[]D-T
LMK212 BJ105[]D-T
LMK212 BJ225[]D-T
LMK212ABJ106[]D-T
LMK212BBJ226MD-T
JMK212ABJ106[]D-T
JMK212ABJ226MD-T
AMK212BBJ476MD-T
Part number 2
【Temperature Characteristic C6 : X6S(-55~+105℃)】 1.25mm thickness(G)
Part number 1
Part number 2
EMK212BC6226MG-TT
LMK212BC6226MG-T
JMK212BC6226MG-T
JMK212BC6476MG-T
AMK212AC6226MG-T
AMK212BC6476MG-T
Rated voltage
[V]
16
10
6.3
4
Temperature
characteristics
X6S
X6S
X6S
X6S
X6S
X6S
Capacitance
[F]
22
22
22
47
22
47
μ
μ
μ
μ
μ
μ
HTLT
Thickness*3 [mm]
Rated voltage x %
150
1.25+0.20/-0
150
1.25+0.20/-0
150
1.25+0.20/-0
150
1.25+0.20/-0
150
1.25+0.15/-0.05
150
1.25+0.20/-0
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
【Temperature Characteristic C6 : X6S(-55~+105℃)】 0.85mm thickness(D)
Part number 1
Part number 2
LMK212AC6106[]D-T
AMK212BC6226MD-T
Rated voltage
[V]
10
4
Temperature
characteristics
Capacitance
[F]
X6S
X6S
10 μ
22 μ
HTLT
Rated voltage x %
150
150
Thickness*3 [mm]
0.85±0.10
0.85±0.10
Soldering
R:Reflow
W:Wave
R
R
【Temperature Characteristic B7 : X7R(-55~+125℃)】 1.25mm thickness(G)
Part number 1
UMK212 B7104[]G-T
UMK212 B7224[]G-T
UMK212 B7474[]G-T
UMK212 B7105[]G-T
UMK212BB7225[]G-T
GMK212 B7105[]G-T
TMK212 B7105[]G-T
TMK212 B7225[]G-TR
TMK212AB7475[]G-T
EMK212 B7105[]G-T
EMK212 B7225[]G-T
EMK212 B7475[]G-T
EMK212BB7106MG-T
LMK212 B7105[]G-T
LMK212 B7225[]G-T
LMK212 B7475[]G-T
LMK212AB7106[]G-T
JMK212AB7106[]G-T
Part number 2
Rated voltage
[V]
50
35
25
TMK212 B7475[]G-T
16
10
LMK212 B7106[]G-TD
JMK212 B7106[]G-T
6.3
Temperature
characteristics
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Thickness*3 [mm]
Rated voltage x %
200
1.25±0.10
150
1.25±0.10
150
1.25±0.10
150
1.25±0.10
150
1.25+0.20/-0
150
1.25±0.10
150
1.25±0.10
150
1.25±0.10
150
1.25+0.15/-0.05
200
1.25±0.10
150
1.25±0.10
150
1.25±0.10
150
1.25+0.20/-0
200
1.25±0.10
200
1.25±0.10
150
1.25±0.10
150
1.25+0.15/-0.05
150
1.25+0.15/-0.05
Soldering
R:Reflow
W:Wave
R/W
R/W
R/W
R/W
R
R/W
R/W
R
R
R/W
R
R
R
R/W
R
R
R
R
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
21
■PARTS NUMBER
【Temperature Characteristic B7 : X7R(-55~+125℃)】 0.85mm thickness(D)
Part number 1
UMK212AB7104[]D-T
UMK212AB7224[]D-T
UMK212AB7474[]D-T
UMK212AB7105[]D-T
TMK212AB7225[]D-TR
EMK212 B7474[]D-T
EMK212 B7105[]D-T
EMK212AB7225[]D-T
EMK212BB7475[]D-T
LMK212 B7105[]D-T
LMK212AB7225[]D-T
LMK212AB7475[]D-TR
Part number 2
Rated voltage
[V]
Temperature
characteristics
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
50
25
EMK212 B7225[]D-T
LMK212 B7225[]D-T
LMK212 B7475[]D-TR
16
10
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
0.1
0.22
0.47
1
2.2
0.47
1
2.2
4.7
1
2.2
4.7
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
10
10
10
10
10
3.5
5
5
10
3.5
5
10
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
150
200
200
150
150
200
200
150
Thickness*3 [mm]
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R/W
R
R
R
R
R
R
CERAMIC CAPACITORS
●316TYPE
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 1.6mm thickness(L)
Part number 1
UMK316 BJ105[]L-T
UMK316 BJ225[]L-T
UMK316 BJ475[]L-T
UMK316BBJ106[]L-T
TMK316 BJ225[]L-T
TMK316 BJ475[]L-T
TMK316 BJ106[]L-T
TMK316BBJ226ML-T
EMK316 BJ225[]L-T
EMK316 BJ475[]L-T
EMK316 BJ106[]L-T
EMK316ABJ226[]L-T
LMK316 BJ106[]L-T
LMK316ABJ226[]L-T
LMK316ABJ476ML-T
LMK316BBJ107ML-T
JMK316 BJ106[]L-T
JMK316ABJ226[]L-T
JMK316ABJ476ML-T
JMK316ABJ107ML-T
AMK316ABJ107ML-T
AMK316BBJ157ML-T
PMK316BBJ227ML-T
Part number 2
Rated voltage
[V]
Temperature
characteristics
B
50
25
16
B
B
B
B
EMK316 BJ226[]L-T
LMK316 BJ226[]L-T
LMK316 BJ476ML-T
JMK316 BJ226[]L-T
JMK316 BJ476ML-T
JMK316 BJ107ML-T
AMK316 BJ107ML-T
10
6.3
4
2.5
X5R*1
X5R
X5R
X5R
X5R*1
X5R
X5R*1
X5R
X5R*1
X5R
X5R*1
X5R
X5R*1
X5R
X5R
X5R
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
1
2.2
4.7
10
2.2
4.7
10
22
2.2
4.7
10
22
10
22
47
100
10
22
47
100
100
150
220
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±20
±10, ±20
±10, ±20
±20
±20
±20
±20
±20
3.5
10
10
10
3.5
5
5
10
3.5
5
5
10
5
10
10
10
5
10
10
10
10
10
10
HTLT
Rated voltage x %
200
150
150
150
200
150
150
150
200
200
150
150
200
150
150
150
200
200
200
150
150
150
150
Thickness*3 [mm]
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.30
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.30
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.30
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.30
1.6±0.30
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R/W
R
R
R
R
R
R
R
R
R
R
R
R
R
R
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 0.85mm thickness(D)
Part number 1
UMK316 BJ105[]D-T
UMK316 BJ225[]D-T
UMK316ABJ475[]D-T
TMK316 BJ105[]D-T
TMK316 BJ225[]D-T
TMK316 BJ475[]D-T
TMK316ABJ106[]D-T
EMK316 BJ225[]D-T
EMK316 BJ475[]D-T
EMK316 BJ106[]D-T
EMK316ABJ226MD-T
LMK316 BJ475[]D-T
LMK316 BJ106[]D-T
LMK316ABJ226MD-T
JMK316 BJ106[]D-T
JMK316ABJ226MD-T
JMK316ABJ476MD-T
Part number 2
Rated voltage
[V]
50
Temperature
characteristics
B
B
UMK316 BJ475[]D-T
25
B
B
TMK316 BJ106[]D-TD
16
B
B
EMK316 BJ226MD-T
B
10
LMK316 BJ226MD-T
JMK316 BJ226MD-T
JMK316 BJ476MD-T
6.3
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
1
2.2
4.7
1
2.2
4.7
10
2.2
4.7
10
22
4.7
10
22
10
22
47
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±20
±10, ±20
±20
±20
3.5
3.5
10
3.5
3.5
5
10
3.5
5
10
10
5
10
10
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
±20
±20
±20
±20
±20
±20
10
10
10
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
±20
10
HTLT
Rated voltage x %
150
150
150
200
150
150
150
200
200
150
150
200
200
150
200
150
150
Thickness*3 [mm]
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
【Temperature Characteristic C6 : X6S(-55~+105℃)】 1.6mm thickness(L)
Part number 1
Part number 2
EMK316BC6226ML-T
LMK316BC6476ML-T
JMK316AC6476ML-T
JMK316BC6107ML-T
AMK316AC6476ML-T
AMK316AC6107ML-T
Rated voltage
[V]
16
10
6.3
4
Temperature
characteristics
X6S
X6S
X6S
X6S
X6S
X6S
Capacitance
[F]
22
47
47
100
47
100
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
150
150
150
150
200
150
Thickness*3 [mm]
1.6±0.30
1.6±0.30
1.6±0.20
1.6±0.30
1.6±0.20
1.6±0.20
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
【Temperature Characteristic C7 : X7S(-55~+125℃)】 1.6mm thickness(L)
Part number 1
AMK316AC7476ML-T
Part number 2
Rated voltage
[V]
4
Temperature
characteristics
Capacitance
[F]
X7S
47 μ
HTLT
Rated voltage x %
150
Thickness*3 [mm]
1.6±0.20
Soldering
R:Reflow
W:Wave
R
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
22
19
■PARTS NUMBER
【Temperature Characteristic B7 : X7R(-55~+125℃)】 1.6mm thickness(L)
Part number 1
Rated voltage
[V]
Temperature
characteristics
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
50
UMK316 B7475[]L-T
35
TMK316 B7475[]L-T
TMK316 B7106[]L-TD
EMK316 B7106[]L-TD
LMK316 B7106[]L-TD
LMK316 B7226[]L-TD
25
16
10
6.3
Capacitance
[F]
Capacitance tolerance
[%]
tanδ
[%]
0.22
0.47
1
2.2
4.7
10
1
2.2
4.7
10
2.2
4.7
10
22
2.2
4.7
10
22
10
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
2.5
3.5
3.5
10
10
10
3.5
3.5
10
10
3.5
5
10
10
3.5
5
10
10
5
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±10, ±20
±20
10
10
10
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
HTLT
Rated voltage x %
200
200
200
150
150
150
200
200
200
150
200
200
200
150
200
200
200
150
200
Thickness*3 [mm]
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.30
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
1.6±0.20
Soldering
R:Reflow
W:Wave
R/W
R/W
R
R
R
R
R/W
R
R
R
R/W
R
R
R
R/W
R
R
R
R
【Temperature Characteristic B7 : X7R(-55~+125℃)】 0.85mm thickness(D)
Part number 1
Part number 2
UMK316 B7225[]D-T
TMK316AB7475[]D-T
LMK316AB7106MD-T
Rated voltage
[V]
Temperature
characteristics
Capacitance
[F]
X7R
X7R
X7R
2.2 μ
4.7 μ
10 μ
50
25
10
HTLT
Rated voltage x %
150
150
150
Thickness*3 [mm]
0.85±0.10
0.85±0.10
0.85±0.10
Soldering
R:Reflow
W:Wave
R
R
R
CERAMIC CAPACITORS
UMK316 B7224[]L-T
UMK316 B7474[]L-T
UMK316 B7105[]L-T
UMK316 B7225[]L-T
UMK316AB7475[]L-T
GMK316AB7106[]L-TR
TMK316 B7105[]L-T
TMK316 B7225[]L-T
TMK316AB7475[]L-T
TMK316AB7106[]L-T
EMK316 B7225[]L-T
EMK316 B7475[]L-T
EMK316AB7106[]L-T
EMK316BB7226ML-T
LMK316 B7225[]L-T
LMK316 B7475[]L-T
LMK316AB7106[]L-T
LMK316AB7226[]L-TR
JMK316 B7106[]L-T
Part number 2
●325TYPE
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 2.5mm thickness(M)
Part number 1
UMK325 BJ475[]M-P
UMK325 BJ106[]M-P
GMK325 BJ226MM-P
TMK325 BJ106[]M-P
TMK325 BJ226[]M-P
TMK325ABJ476MM-P
EMK325 BJ226[]M-P
EMK325 BJ476MM-P
EMK325ABJ107MM-P
LMK325 BJ226[]M-P
LMK325 BJ476MM-P
LMK325ABJ107MM-P
LMK325ABJ227MM-PE
JMK325 BJ476MM-P
JMK325ABJ107MM-P
JMK325ABJ157MM-P
JMK325ABJ227MM-P
AMK325ABJ157MM-P
AMK325ABJ227MM-P
AMK325ABJ337MM-P
Part number 2
Rated voltage
[V]
Temperature
characteristics
50
35
B
25
B
16
B
LMK325 BJ107MM-P
JMK325 BJ107MM-P
10
6.3
4
X5R
X5R
X5R
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
4.7
10
22
10
22
47
22
47
100
22
47
100
220
47
100
150
220
150
220
330
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±20
±10, ±20
±20
±20
±10, ±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
±20
5
5
5
3.5
5
10
5
10
10
5
10
10
10
10
10
10
10
10
10
10
HTLT
Rated voltage x %
150
150
150
150
150
150
150
150
150
200
150
150
150
150
150
150
150
150
150
150
Thickness*3 [mm]
2.5±0.20
2.5±0.20
2.5±0.20
2.5±0.20
2.5±0.20
2.5±0.30
2.5±0.20
2.5±0.20
2.5±0.30
2.5±0.20
2.5±0.20
2.5±0.30
2.5±0.30
2.5±0.20
2.5±0.30
2.5±0.30
2.5±0.30
2.5±0.30
2.5±0.30
2.5±0.30
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 1.9mm thickness(Y,N)
Part number 1
Part number 2
UMK325 BJ475[]N-T
GMK325 BJ225[]N-T
GMK325 BJ475[]N-T
GMK325 BJ106[]N-T
TMK325 BJ335MN-T
TMK325 BJ475[]N-T
TMK325 BJ106[]N-T
EMK325 BJ475[]N-T
EMK325 BJ106[]N-T
EMK325 BJ476MY-T
LMK325 BJ226MY-T
LMK325 BJ106[]N-T
JMK325 BJ226MY-T
JMK325 BJ107MY-T
JMK325 BJ476MN-T
Rated voltage
[V]
Temperature
characteristics
50
B
35
25
B
B
B
16
10
B
B
6.3
X5R
X5R
X5R
X5R
X5R*1
X5R*1
X5R
X5R*1
X5R
X5R
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
4.7
2.2
4.7
10
3.3
4.7
10
4.7
10
47
22
10
22
100
47
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
μ
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
±10, ±20
±20
±20
±10, ±20
±20
±20
±20
10
3.5
10
5
3.5
3.5
5
3.5
3.5
10
5
3.5
5
10
10
HTLT
Rated voltage x %
150
200
150
150
200
200
200
200
200
150
150
200
200
150
150
Thickness*3 [mm]
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
1.9+0.1/-0.2
1.9+0.1/-0.2
1.9±0.20
1.9+0.1/-0.2
1.9+0.1/-0.2
1.9±0.20
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
【Temperature Characteristic BJ : B(-25~+85℃)/X5R(-55~+85℃)】 0.85mm thickness(D)
Part number 1
TMK325 BJ106[]D-T
EMK325 BJ106[]D-T
EMK325 BJ226MD-T
LMK325 BJ335[]D-T
LMK325 BJ475[]D-T
LMK325 BJ106[]D-T
Part number 2
Rated voltage
[V]
Temperature
characteristics
25
16
10
B
B
X5R
X5R
X5R
X5R
X5R
X5R
Capacitance
[F]
10
10
22
3.3
4.7
10
μ
μ
μ
μ
μ
μ
Capacitance tolerance
[%]
tanδ
[%]
±10, ±20
±10, ±20
±20
±10, ±20
±10, ±20
±10, ±20
5
5
10
3.5
5
5
HTLT
Rated voltage x %
150
150
150
200
200
150
Thickness*3 [mm]
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
0.85±0.10
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
23
■PARTS NUMBER
【Temperature Characteristic C6 : X6S(-55~+105℃)】 2.5mm thickness(M)
Part number 1
Part number 2
EMK325AC6476MM-P
LMK325AC6107MM-P
JMK325AC6227MM-PE
JMK325AC6107MM-P
AMK325AC6157MM-P
AMK325AC6227MM-P
PMK325AC6337MM-P
Rated voltage
[V]
16
10
6.3
4
2.5
Temperature
characteristics
X6S
X6S
X6S
X6S
X6S
X6S
X6S
Capacitance
[F]
47
100
220
100
150
220
330
μ
μ
μ
μ
μ
μ
μ
Capacitance tolerance
[%]
tanδ
[%]
±20
±20
±20
±20
±20
±20
±20
10
10
10
10
10
10
10
Capacitance tolerance
[%]
tanδ
[%]
±20
10
Capacitance tolerance
[%]
tanδ
[%]
HTLT
Rated voltage x %
150
150
150
150
150
150
150
Thickness*3 [mm]
2.5±0.30
2.5±0.30
2.5±0.30
2.5±0.30
2.5±0.30
2.5±0.30
2.5±0.30
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
【Temperature Characteristic C7 : X7S(-55~+125℃)】 2.5mm thickness(M)
Part number 1
Part number 2
CERAMIC CAPACITORS
JMK325AC7107MM-P
Rated voltage
[V]
6.3
Temperature
characteristics
Capacitance
[F]
X7S
100 μ
HTLT
Rated voltage x %
150
Thickness*3 [mm]
2.5±0.30
Soldering
R:Reflow
W:Wave
R
【Temperature Characteristic B7 : X7R(-55~+125℃)】 2.5mm thickness(M)
Part number 1
Part number 2
UMK325 B7335[]M-P
UMK325 B7475[]M-P
UMK325AB7106[]M-P
TMK325AB7106[]M-P
TMK325 B7226[]M-PR
EMK325 B7226[]M-PR
LMK325 B7476[]M-PR
JMK325 B7476[]M-PR
Rated voltage
[V]
50
25
16
10
6.3
Temperature
characteristics
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
Capacitance
[F]
3.3
4.7
10
10
22
22
47
47
μ
μ
μ
μ
μ
μ
μ
μ
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±20
±20
±20
±20
±20
±20
±20
±20
3.5
5
10
10
10
10
10
10
HTLT
Rated voltage x %
200
150
150
200
150
150
150
200
Thickness*3 [mm]
2.5±0.20
2.5±0.20
2.5±0.30
2.5±0.30
2.5±0.20
2.5±0.20
2.5±0.20
2.5±0.20
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
R
【Temperature Characteristic B7 : X7R(-55~+125℃)】 1.9mm thickness(N)
Part number 1
Part number 2
UMK325 B7475[]N-TR
TMK325 B7335[]N-T
TMK325 B7475[]N-T
TMK325 B7106[]N-TR
EMK325 B7475[]N-T
EMK325 B7106[]N-T
LMK325 B7106[]N-T
Rated voltage
[V]
50
25
16
10
Temperature
characteristics
X7R
X7R
X7R
X7R
X7R
X7R
X7R
Capacitance
[F]
4.7
3.3
4.7
10
4.7
10
10
μ
μ
μ
μ
μ
μ
μ
Capacitance tolerance
[%]
±10,
±10,
±10,
±10,
±10,
±10,
±10,
±20
±20
±20
±20
±20
±20
±20
tanδ
[%]
10
3.5
3.5
10
3.5
3.5
3.5
HTLT
Rated voltage x %
150
200
150
150
200
150
200
Thickness*3 [mm]
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
1.9±0.20
Soldering
R:Reflow
W:Wave
R
R
R
R
R
R
R
●432TYPE
【Temperature Characteristic BJ : X5R(-55~+85℃)】 2.5mm thickness(M)
Part number 1
Part number 2
AMK432 BJ477MM-T
Rated voltage
[V]
4
Temperature
characteristics
Capacitance
[F]
X5R
470 μ
Capacitance tolerance
[%]
tanδ
[%]
±20
10
Capacitance tolerance
[%]
tanδ
[%]
±20
10
HTLT
Rated voltage x %
150
Thickness*3 [mm]
2.5±0.20
Soldering
R:Reflow
W:Wave
R
【Temperature Characteristic C6 : X6S(-55~+105℃)】 2.5mm thickness(M)
Part number 1
PMK432 C6477MM-T
Part number 2
Rated voltage
[V]
2.5
Temperature
characteristics
Capacitance
[F]
X6S
470 μ
HTLT
Rated voltage x %
150
Thickness*3 [mm]
2.5±0.20
Soldering
R:Reflow
W:Wave
R
c_mlcc_e-E07R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
24
19
Multilayer Ceramic Capacitors
■PACKAGING
①Minimum Quantity
●Taped package
Thickness
Type(EIA)
□MK021(008004)
□VS021(008004)
□MK042(01005)
□VS042(01005)
□MK063(0201)
□WK105(0204) ※
□MK105(0402)
□MF105(0402)
□VK105(0402)
□MK107(0603)
□WK107(0306) ※
□MF107(0603)
□VS107(0603)
□MJ107(0603)
□MK212(0805)
□WK212(0508) ※
□MF212(0805)
□VS212(0805)
□MJ212(0805)
□MK316(1206)
□MF316(1206)
□MJ316(1206)
□MK325(1210)
□MF325(1210)
□MJ325(1210)
□MK432(1812)
Note : ※ LW Reverse type.
mm
code
0.125
K
0.2
0.2
0.3
0.3
0.13
0.18
0.2
0.3
0.5
0.5
0.45
0.5
0.8
0.7
0.8
0.45
0.85
1.25
0.85
0.85
1.25
0.85
1.15
1.6
1.15
1.6
0.85
1.15
1.9
2.0max.
2.5
1.9
2.5
2.5
C, D
C
P,T
P
H
E
C
P
V
W
K
V
A
C
A
K
D
G
D
D
G
D
F
L
F
L
D
F
N
Y
M
N
M
M
Standard quantity [pcs]
Paper tape
Embossed tape
-
50000
-
40000
15000
10000
-
-
20000
15000
10000
10000
4000
-
4000
4000
3000
-
-
20000
15000
-
-
-
-
-
4000
-
-
3000
4000
-
-
4000
4000
-
4000
-
-
-
-
3000
-
-
2000
-
3000
2000
3000
2000
-
2000
-
-
-
-
1000
2000
500(T), 1000(P)
500
②Taping material
※No bottom tape for pressed carrier tape
●Card board carrier tape
●Embossed tape
Top tape
Top tape
Base tape
Sprocket hole
Sprocket hole
Bottom tape
Chip cavity
Base tape
Chip cavity
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_pack_e-E06R01
Chip filled
Chip
※ LW Reverse type.
③Representative taping dimensions
●Paper Tape(8mm wide)
●Pressed carrier tape( 2mm pitch)
Unit:mm(inch)
A
B
T
8.0±0.3
(0.315±0.012)
Sprocket hole
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
T1
2.0±0.05
(0.079±0.002)
F
4.0±0.1
(0.157±0.004)
Chip Cavity
Type(EIA)
A
0.37
Insertion Pitch
F
B
0.67
□MK063(0201)
□WK105(0204) ※
0.65
1.15
□MK105(0402) (*1 C)
□MK105(0402) (*1 P)
Note *1 Thickness, C:0.2mm ,P:0.3mm. ※ LW Reverse type.
2.0±0.05
●Punched carrier tape (2mm pitch)
0.45max.
0.42max.
0.4max.
0.45max.
0.3max.
0.42max.
Unit:mm
T
8.0±0.3
(0.315±0.012)
B
2.0±0.05
(0.079±0.002)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
A
F
T1
Unit:mm(inch)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
Tape Thickness
T
4.0±0.1
(0.157±0.004)
A
Chip Cavity
B
Insertion Pitch
F
Tape Thickness
T
0.65
1.15
2.0±0.05
0.8max.
Type(EIA)
□MK105 (0402)
□MF105 (0402)
□VK105 (0402)
Unit:mm
●Punched carrier tape (4mm pitch)
B
T
8.0±0.3
(0.315±0.012)
A
F
Unit:mm(inch)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
Sprocket hole
φ1.5+0.1/-0
(φ0.059+0.004/-0)
4.0±0.1
(0.157±0.004)
2.0±0.1
(0.079±0.004)
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_pack_e-E06R01
Chip Cavity
Type(EIA)
A
Insertion Pitch
F
B
□MK107(0603)
□WK107(0306) ※
1.0
1.8
□MF107(0603)
4.0±0.1
□MK212(0805)
1.65
2.4
□WK212(0508) ※
□MK316(1206)
2.0
3.6
Note:Taping size might be different depending on the size of the product. ※ LW Reverse type.
●Embossed tape(4mm wide)
Unit:mm
4.0±0.05
(0.157±0.002)
B
1.0±0.02
(0.039±0.001)
1.1max.
0.9±0.05
(0.035±0.002)
1.8±0.02
(0.071±0.001)
A
F
1.1max.
Unit:mm(inch)
φ0.8±0.04
(φ0.031±0.002)
Sprocket hole
Tape Thickness
T
2.0±0.04
(0.079±0.002)
Chip Cavity
Type(EIA)
□MK021(008004)
□VS021(008004)
□MK042(01005)
□VS042(01005)
A
B
0.135
0.27
0.23
0.43
Insertion Pitch
F
K
Tape Thickness
T
1.0±0.02
0.5max.
0.25max.
Unit:mm
●Embossed tape(8mm wide)
Unit:mm(inch)
3.5±0.05
(0.138±0.002)
Sprocket hole
A
B
F
1.75±0.1
(0.069±0.004)
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
4.0±0.1
(0.157±0.004)
2.0±0.1
(0.079±0.004)
Type(EIA)
□MK105(0402)
□WK107(0306) ※
□MK212(0805)
□MF212(0805)
□MK316(1206)
□MF316(1206)
□MK325(1210)
□MF325(1210)
Note: ※ LW Reverse type.
Chip Cavity
A
0.6
1.0
B
1.1
1.8
1.65
2.4
2.0
3.6
2.8
3.6
Insertion Pitch
F
2.0±0.1
4.0±0.1
Tape Thickness
K
0.6max
1.3max.
T
0.2±0.1
0.25±0.1
3.4max.
0.6max.
Unit:mm
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_pack_e-E06R01
●Embossed tape(12mm wide)
Unit:mm(inch)
5.5±0.05
(0.217±0.002)
Sprocket hole
A
B
4.0±0.1
(0.157±0.004)
12.0±0.3
(0.472±0.012)
1.75±0.1
(0.069±0.004)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
2.0±0.1
(0.079±0.004)
F
Chip Cavity
Type(EIA)
A
3.1
3.7
□MK325(1210)
□MK432(1812)
B
4.0
4.9
Insertion Pitch
F
8.0±0.1
8.0±0.1
K
4.0max.
4.0max.
Tape Thickness
E
2.0±0.5
T
0.6max.
0.6max.
Unit:mm
④Trailer and Leader
Blank portion
Chip cavity
Blank portion
Leader
100mm or more
(3.94inches or more)
160mm or more
(6.3inches or more)
Direction of tape feed
400mm or more
(15.7inches or more)
⑤Reel size
t
E
C
R
B
A
D
W
A
φ178±2.0
B
φ50min.
C
φ13.0±0.2
D
φ21.0±0.8
4mm wide tape
8mm wide tape
12mm wide tape
T
1.5max.
2.5max.
2.5max.
W
5±1.0
10±1.5
14±1.5
Unit:mm
R
1.0
⑥Top Tape Strength
The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below.
Pull direction
0~20°
Top tape
Base tape
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_pack_e-E06R01
Super Low Distortion Multilayer Ceramic Capacitors , Medium-High Voltage Multilayer Ceramic Capacitors and
High Reliability Application Multilayer Ceramic Capacitors are noted separately.
Multilayer Ceramic Capacitors
■RELIABILITY DATA
1.Operating Temperature Range
Temperature
Compensating(Class1)
Standard
High Frequency Type
-55 to +125℃
B7
C6
C7
Specification
B
X5R
X7R
X6S
X7S
Temperature Range
-25 to +85℃
-55 to +85℃
-55 to +125℃
-55 to +105℃
-55 to +125℃
LD(※)
X5R
-55 to +85℃
BJ
Specified
Value
High Permittivity (Class2)
Note: ※LD Low distortion high value multilayer ceramic capacitor
2. Storage Conditions
Temperature
Compensating(Class1)
Standard
High Frequency Type
-55 to +125℃
Specification
Temperature Range
B
-25 to +85℃
BJ
X5R
-55 to +85℃
B7
X7R
-55 to +125℃
C6
X6S
-55 to +105℃
C7
X7S
-55 to +125℃
LD(※)
X5R
-55 to +85℃
Note: ※LD Low distortion high value multilayer ceramic capacitor
Specified
Value
High Permittivity (Class2)
3. Rated Voltage
Specified
Value
Temperature
Compensating(Class1)
Standard
50VDC, 25VDC, 16VDC
High Frequency Type
50VDC, 25VDC, 16VDC
High Permittivity (Class2)
50VDC, 35VDC, 25VDC, 16VDC, 10VDC, 6.3VDC, 4VDC, 2.5VDC
4. Withstanding Voltage (Between terminals)
Specified
Value
Temperature
Compensating(Class1)
Standard
High Frequency Type
No breakdown or damage
High Permittivity (Class2)
Test
Methods and
Remarks
Class 1
Rated voltage×3
Applied voltage
Duration
Charge/discharge current
Class 2
Rated voltage×2.5
1 to 5 sec.
50mA max.
5. Insulation Resistance
Specified
Value
Temperature
Compensating(Class1)
Standard
High Frequency Type
High Permittivity (Class2) Note 1
Test
Methods and
Remarks
Applied voltage
Duration
Charge/discharge current
10000 MΩmin.
C≦0.047μF : 10000 MΩ min.
C>0.047μF : 500MΩ・μF
: Rated voltage
: 60±5 sec.
: 50mA max.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
6. Capacitance (Tolerance)
Specified
Value
Standard
C□
U□
SL
0.2pF≦C≦5pF
0.2pF≦C≦10pF
C>10pF
: ±0.25pF
: ±0.5pF
: ±5% or ±10%
High Frequency Type
CG
0.2pF≦C≦2pF
C>2pF
: ±0.1pF
: ±5%
Temperature
Compensating(Class1)
High Permittivity (Class2)
Test
Methods and
Remarks
±10% or ±20%
Standard
Preconditioning
Measuring frequency
Measuring voltage Nte
Bias application
Class 1
High Frequency Type
None
1MHz±10%
0.5 to 5Vrms
Class 2
C≦10μF
C>10μF
Thermal treatment (at 150℃ for 1hr) Note 2
1kHz±10%
120±10Hz
1±0.2Vrms
0.5±0.1Vrms
None
7. Q or Dissipation Factor
Specified
Value
Temperature
Compensating(Class1)
C<30pF : Q≧400+20C
C≧30pF : Q≧1000
(C:Nominal capacitance)
Standard
High Frequency Type
High Permittivity (Class2) Note 1
Refer to detailed specification
BJ, B7, C6, C7:2.5% max.
Class 1
High Frequency Type
None
1MHz±10%
1GHz
0.5 to 5Vrms
Standard
Test
Methods and
Remarks
Preconditioning
Measuring frequency
Measuring voltage Note 1
Bias application
High Frequency Type
Measuring equipment
Measuring jig
Class 2
C≦10μF
C>10μF
Thermal treatment (at 150℃ for 1hr) Note 2
1kHz±10%
120±10Hz
1±0.2Vrms
0.5±0.1Vrms
None
: HP4291A
: HP16192A
8. Temperature Characteristic (Without voltage application)
Temperature Characteristic [ppm/℃]
C□ : 0
CG
Standard
Temperature
Compensating(Class1)
U□ : -750
SL
High Frequency Type
UJ, UK
: +350 to -1000
Temperature Characteristic [ppm/℃]
C□ : 0
CG
Specified
Value
Tolerance [ppm/℃]
G : ±30
J:±120
K:±250
Tolerance [ppm/℃]
G : ±30
Capacitance
Reference
Temperature Range
change
temperature
±10%
20℃
-25 to +85℃
±15%
25℃
-55 to +85℃
±15%
25℃
-55 to +125℃
±22%
25℃
-55 to +105℃
±22%
25℃
-55 to +125℃
±15%
25℃
-55 to +85℃
distortion high value multilayer ceramic capacitor
Specification
B
X5R
B7
X7R
C6
XS
C7
X7S
LD(※)
X5R
Note : ※LD Low
BJ
High Permittivity (Class2)
Class 1
Capacitance at 20℃ and 85℃ shall be measured in thermal equilibrium, and the temperature characteristic shall be calculated from the
following equation.
(C85-C20)
×106(ppm/℃)
△T=65
C20×△T
Test
Methods and
Remarks
Class 2
Capacitance at each step shall be measured in thermal equilibrium, and the temperature characteristic shall be calculated from the following
equation.
Step
B
X5R、X7R、X6S、X7S
1
Minimum operating temperature
2
20℃
25℃
3
Maximum operating temperature
(C-C2)
C2
×100(%)
C :Capacitance in Step 1 or Step 3
C2 :Capacitance in Step 2
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
9. Deflection
Specified
Value
Temperature
Compensating(Class1)
Standard
Appearance
Capacitance change
: No abnormality
: Within ±5% or ±0.5 pF, whichever is larger.
High Frequency Type
Appearance
Capacitance change
: No abnormality
: Within±0.5 pF
Appearance
Capacitance change
: No abnormality
: Within ±12.5%
High Permittivity (Class2)
Board
Thickness
Warp
Duration
Test
Methods and
Remarks
Multilayer Ceramic Capacitors
021, 042, 063, ※105 Type
The other types
Glass epoxy-resin substrate
0.8mm
1.6mm
1mm
10 sec.
※
105 Type thickness, C: 0.2mm ,P: 0.3mm.
Capacitance measurement shall be conducted
with the board bent
10. Body Strength
Specified
Value
Standard
Temperature
Compensating(Class1)
High Frequency Type
High Permittivity (Class2)
Test
Methods and
Remarks
-
No mechanical damage.
-
High Frequency 105Type
Applied force
: 5N
Duraton
: 10 sec.
11. Adhesive Strength of Terminal Electrodes
Specified
Value
Standard
Temperature
Compensating(Class1)
High Frequency Type
No terminal separation or its indication.
High Permittivity (Class2)
Test
Methods and
Remarks
Applied force
Duration
Multilayer Ceramic Capacitors
021, 042, 063 Type
105 Type or more
2N
5N
30±5 sec.
12. Solderability
Specified
Value
Temperature
Compensating(Class1)
Standard
High Frequency Type
At least 95% of terminal electrode is covered by new solder.
High Permittivity (Class2)
Test
Methods and
Remarks
Solder type
Solder temperature
Duration
Eutectic solder
H60A or H63A
230±5℃
Lead-free solder
Sn-3.0Ag-0.5Cu
245±3℃
4±1 sec.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
13. Resistance to Soldering
Standard
Appearance
Capacitance change
Q
Insulation resistance
Withstanding voltage
: No abnormality
: Within ±2.5% or ±0.25pF, whichever is larger.
: Initial value
: Initial value
(between terminals) : No abnormality
High Frequency Type
Appearance
Capacitance change
Q
Insulation resistance
Withstanding voltage
: No abnormality
: Within ±2.5%
: Initial value
: Initial value
(between terminals) : No abnormality
Appearance
Capacitance change
Dissipation factor
Insulation resistance
Withstanding voltage
: No abnormality
: Within ±7.5%
: Initial value
: Initial value
(between terminals): No abnormality
Temperature
Compensating(Class1)
Specified
Value
High Permittivity (Class2)
Note 1
Class 1
021, 042, 063 Type
105 Type
Preconditioning
Preheating
Test
Methods and
Remarks
None
80 to 100℃, 2 to 5 min.
150 to 200℃, 2 to 5 min.
150℃, 1 to 2 min.
Solder temp.
Duration
Recovery
270±5℃
3±0.5 sec.
6 to 24 hrs (Standard condition) Note 5
021, 042、063 Type
Preconditioning
Preheating
150℃, 1 to 2 min.
Solder temp.
Duration
Recovery
Class 2
105, 107, 212 Type
316, 325, 432 Type
Thermal treatment (at 150℃ for 1 hr) Note 2
80 to 100℃, 2 to 5 min.
80 to 100℃, 5 to 10 min.
150 to 200℃, 2 to 5 min.
150 to 200℃, 5 to 10 min.
270±5℃
3±0.5 sec.
24±2 hrs (Standard condition) Note 5
14. Temperature Cycle (Thermal Shock)
Standard
Appearance
Capacitance change
Q
Insulation resistance
Withstanding voltage
: No abnormality
: Within ±2.5% or ±0.25pF, whichever is larger.
: Initial value
: Initial value
(between terminals) : No abnormality
High Frequency Type
Appearance
Capacitance change
Q
Insulation resistance
Withstanding voltage
: No abnormality
: Within ±0.25pF
: Initial value
: Initial value
(between terminals) : No abnormality
Appearance
Capacitance change
Dissipation factor
Insulation resistance
Withstanding voltage
: No abnormality
: Within ±7.5%
: Initial value
: Initial value
(between terminals) : No abnormality
Temperature
Compensating(Class1)
Specified
Value
High Permittivity (Class2)
Note 1
Class 1
Preconditioning
Test
Methods and
Remarks
1 cycle
Number of cycles
Recovery
Class 2
Thermal treatment (at 150℃ for 1 hr)
Note 2
None
Step
1
2
3
4
Temperature(℃)
Minimum operating temperature
Normal temperature
Maximum operating temperature
Normal temperature
Time(min.)
30±3
2 to 3
30±3
2 to 3
5 times
6 to 24 hrs (Standard condition) Note 5
24±2 hrs (Standard condition) Note 5
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
15. Humidity (Steady State)
Appearance
Capacitance change
Q
Standard
Temperature
Compensating(Class1)
Specified
Value
High Frequency Type
High Permittivity (Class2)
Note 1
Insulation resistance
: No abnormality
: Within ±5% or ±0.5pF, whichever is larger.
: C<10pF : Q≧200+10C
10≦C<30pF : Q≧275+2.5C
C≧30pF:Q≧350(C:Nominal capacitance)
: 1000 MΩmin.
Appearance
Capacitance change
Insulation resistance
: No abnormality
: Within ±0.5pF,
: 1000 MΩmin.
Appearance
Capacitance change
Dissipation factor
Insulation resistance
:
:
:
:
Class 1
Standard
Test
Methods and
Remarks
Preconditioning
Temperature
Humidity
Duration
Recovery
No abnormality
Within ±12.5%
5.0% max.
50 MΩμF or 1000 MΩwhichever is smaller.
Class 2
All items
Thermal treatment( at 150℃ for 1 hr) Note 2
40±2℃
90 to 95%RH
500+24/-0 hrs
24±2 hrs (Standard condition) Note 5
High Frequency Type
None
40±2℃
60±2℃
90 to 95%RH
500+24/-0 hrs
6 to 24 hrs (Standard condition) Note 5
16. Humidity Loading
Appearance
Capacitance change
Q
Standard
Insulation resistance
Temperature
Compensating(Class1)
Specified
Value
Appearance
Capacitance change
Note 1
Appearance
Capacitance change
Dissipation factor
Insulation resistance
:
:
:
:
90 to 95%RH
500+24/-0 hrs
Rated voltage
50mA max.
50mA max.
6 to 24 hrs (Standard condition) Note 5
24±2 hrs(Standard condition) Note 5
Preconditioning
Temperature
Humidity
Duration
Applied voltage
Charge/discharge
current
Recovery
Class 1
High Frequency Type
No abnormality
Within ±12.5%
5.0% max.
25 MΩμF or 500 MΩ, whichever is smaller.
Class 2
All items
Voltage treatment
(Rated voltage are applied for 1 hour at 40℃) Note 3
40±2℃
90 to 95%RH
500+24/-0 hrs
Rated voltage
Standard
Test
Methods and
Remarks
Insulation resistance
: No abnormality
: C≦2pF:Within ±0.4 pF
C>2pF:Within ±0.75 pF
(C:Nominal capacitance)
: 500 MΩmin.
High Frequency Type
High Permittivity (Class2)
: No abnormality
: Within ±7.5% or ±0.75pF, whichever is larger.
: C<30pF:Q≧100+10C/3
C≧30pF:Q≧200 (C:Nominal capacitance)
: 500 MΩmin.
None
40±2℃
60±2℃
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
17. High Temperature Loading
Appearance
Capacitance change
Q
Standard
Temperature
Compensating(Class1)
Specified
Value
High Frequency Type
High Permittivity (Class2)
Note 1
Test
Methods and
Remarks
Temperature
Duration
Applied voltage
Charge/discharge
current
Recovery
Appearance
Capacitance change
Insulation resistance
: No abnormality
: Within ±3% or ±0.3pF, whichever is larger.
: 1000 MΩmin.
Appearance
Capacitance change
Dissipation factor
Insulation resistance
:
:
:
:
Class 1
High Frequency Type
No abnormality
Within ±12.5%
5.0% max.
50 MΩμF or 1000 MΩ, whichever is smaller.
Maximum operating temperature
1000+48/-0 hrs
Rated voltage×2 Note 4
Class 2
BJ, LD(※)
C6
B7, C7
Voltage treatment(Twice the rated voltage shall be applied for
1 hour at 85℃, 105℃ or 125℃) Note 3, 4
Maximum operating temperature
1000+48/-0 hrs
Rated voltage×2 Note 4
50mA max.
50mA max.
6 to 24hr (Standard condition) Note 5
24±2 hrs (Standard condition) Note 5
Standard
Preconditioning
Insulation resistance
: No abnormality
: Within ±3% or ±0.3pF, whichever is larger.
: C<10pF: Q≧200+10C
10≦C<30pF:Q≧275+2.5C
C≧30pF: Q≧350(C:Nominal capacitance)
: 1000 MΩmin.
None
Note: ※LD Low distortion high value multilayer ceramic capacitor
Note 1 The figures indicate typical specifications. Please refer to individual specifications in detail.
Note 2 Thermal treatment : Initial value shall be measured after test sample is heat-treated at 150+0/-10℃ for an hour and kept at room temperature for
24±2hours.
Note 3 Voltage treatment : Initial value shall be measured after test sample is voltage-treated for an hour at both the temperature and voltage specified in
the test conditions, and kept at room temperature for 24±2hours.
Note 4 150% of rated voltage is applicable to some items. Please refer to their specifications for further information.
Note 5 Standard condition: Temperature: 5 to 35℃, Relative humidity: 45 to 85 % RH, Air pressure: 86 to 106kPa When there are questions concerning
measurement results, in order to provide correlation data, the test shall be conducted under the following condition.
Temperature: 20±2℃, Relative humidity: 60 to 70 % RH, Air pressure: 86 to 106kPa Unless otherwise specified, all the tests are conducted under the
"standard condition".
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_reli_e-E06R01
High Reliability Application Multilayer Ceramic Capacitors are noted separately.
Precautions on the use of Multilayer Ceramic Capacitors
■PRECAUTIONS
1. Circuit Design
Precautions
◆Verification of operating environment, electrical rating and performance
1. A malfunction of equipment in fields such as medical, aerospace, nuclear control, etc. may cause serious harm to human life or have
severe social ramifications.
Therefore, any capacitors to be used in such equipment may require higher safety and reliability, and shall be clearly differentiated from
them used in general purpose applications.
◆Operating Voltage (Verification of Rated voltage)
1. The operating voltage for capacitors must always be their rated voltage or less.
If an AC voltage is loaded on a DC voltage, the sum of the two peak voltages shall be the rated voltage or less.
For a circuit where an AC or a pulse voltage may be used, the sum of their peak voltages shall also be the rated voltage or less.
2. Even if an applied voltage is the rated voltage or less reliability of capacitors may be deteriorated in case that either a high frequency AC
voltage or a pulse voltage having rapid rise time is used in a circuit.
2. PCB Design
Precautions
◆Pattern configurations (Design of Land-patterns)
1. When capacitors are mounted on PCBs, the amount of solder used (size of fillet) can directly affect the capacitor performance.
Therefore, the following items must be carefully considered in the design of land patterns:
(1)Excessive solder applied can cause mechanical stresses which lead to chip breaking or cracking. Therefore, please consider
appropriate land-patterns for proper amount of solder.
(2)When more than one component are jointly soldered onto the same land, each component's soldering point shall be separated by
solder-resist.
◆Pattern configurations (Capacitor layout on PCBs)
After capacitors are mounted on boards, they can be subjected to mechanical stresses in subsequent manufacturing processes (PCB
cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering of the boards, etc.). For this reason, land
pattern configurations and positions of capacitors shall be carefully considered to minimize stresses.
◆Pattern configurations (Design of Land-patterns)
The following diagrams and tables show some examples of recommended land patterns to prevent excessive solder amounts.
(1)Recommended land dimensions for typical chip capacitors
Land patterns for PCBs
●Multilayer Ceramic Capacitors : Recommended land dimensions
Land pattern
(unit: mm)
Solder-resist
Wave-soldering
Chip capacitor
Type
107
212
316
325
L
1.6
2.0
3.2
3.2
C
Size
W
0.8
1.25
1.6
2.5
A
0.8 to 1.0
1.0 to 1.4
1.8 to 2.5
1.8 to 2.5
B
0.5 to 0.8
0.8 to 1.5
0.8 to 1.7
0.8 to 1.7
B
A
B
C
0.6 to 0.8
0.9 to 1.2
1.2 to 1.6
1.8 to 2.5
Chip capacitor
W
Technical
considerations
L
Reflow-soldering
Type
021
L
0.25
Size
W
0.125
A
0.095~0.135
B
0.085~0.125
C
0.110~0.150
Note:Recommended land
042
0.4
0.2
0.15~0.25
0.15~0.20
0.15~0.30
size might be
063
105
107
212
316
0.6
1.0
1.6
2.0
3.2
0.3
0.5
0.8
1.25
1.6
0.20~0.30 0.45~0.55
0.8~1.0
0.8~1.2
1.8~2.5
0.20~0.30 0.40~0.50
0.6~0.8
0.8~1.2
1.0~1.5
0.25~0.40 0.45~0.55
0.6~0.8
0.9~1.6
1.2~2.0
different according to the allowance of the size of the product.
●LWDC: Recommended land dimensions
(unit: mm)
Type
105
107
L
0.52
0.8
Size
W
1.0
1.6
A
0.18~0.22
0.25~0.3
B
0.2~0.25
0.3~0.4
C
0.9~1.1
1.5~1.7
for reflow-soldering
212
1.25
2.0
0.5~0.7
0.4~0.5
1.9~2.1
325
3.2
2.5
1.8~2.5
1.0~1.5
1.8~3.2
432
4.5
3.2
2.5~3.5
1.5~1.8
2.3~3.5
LWDC
W
L
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
(2)Examples of good and bad solder application
Item
Not recommended
Lead wire of component
Recommended
Solder-resist
Mixed mounting of SMD and
leaded components
Chassis
Solder (for grounding)
Solder-resist
Component placement close to
the chassis
Electrode pattern
Lead wire of component
Soldering iron
Hand-soldering of leaded
components near mounted
components
Solder-resist
Solder-resist
Horizontal component
placement
◆Pattern configurations (Capacitor layout on PCBs)
1-1. The following is examples of good and bad capacitor layouts ; capacitors shall be located to minimize any
stresses from board warp or deflection.
Items
Not recommended
Recommended
possible mechanical
Place the product at a right
angle to the direction of the
anticipated mechanical
stress.
Deflection of board
1-2. The amount of mechanical stresses given will vary depending on capacitor layout. Please refer to diagram below.
E
D
Perforation
C
A
B
Slit
Magnitude of stress
A>B=C>D>E
1-3. When PCB is split, the amount of mechanical stress on the capacitors can vary according to the method used. The following methods
are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, please consider the PCB,
split methods as well as chip location.
3. Mounting
Precautions
◆Adjustment of mounting machine
1. When capacitors are mounted on PCB, excessive impact load shall not be imposed on them.
2. Maintenance and inspection of mounting machines shall be conducted periodically.
◆Selection of Adhesives
1. When chips are attached on PCBs with adhesives prior to soldering, it may cause capacitor characteristics degradation unless the
following factors are appropriately checked : size of land patterns, type of adhesive, amount applied, hardening temperature and
hardening period. Therefore, please contact us for further information.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
◆Adjustment of mounting machine
1. When the bottom dead center of a pick-up nozzle is too low, excessive force is imposed on capacitors and causes damages. To avoid
this, the following points shall be considerable.
(1)The bottom dead center of the pick-up nozzle shall be adjusted to the surface level of PCB without the board deflection.
(2)The pressure of nozzle shall be adjusted between 1 and 3 N static loads.
(3)To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins shall be
used on the other side of the PCB. The following diagrams show some typical examples of good and bad pick-up nozzle
placement:
Item
Improper method
Proper method
Single-sided mounting
chipping
or cracking
supporting pins
or back-up pins
Double-sided mounting
chipping
or cracking
Technical
considerations
supporting pins
or back-up pins
2. As the alignment pin is worn out, adjustment of the nozzle height can cause chipping or cracking of capacitors because of mechanical
impact on the capacitors.
To avoid this, the monitoring of the width between the alignment pins in the stopped position, maintenance, check and replacement of
the pin shall be conducted periodically.
◆Selection of Adhesives
Some adhesives may cause IR deterioration. The different shrinkage percentage of between the adhesive and the capacitors may result in
stresses on the capacitors and lead to cracking. Moreover, too little or too much adhesive applied to the board may adversely affect
components. Therefore, the following precautions shall be noted in the application of adhesives.
(1)Required adhesive characteristics
a. The adhesive shall be strong enough to hold parts on the board during the mounting & solder process.
b. The adhesive shall have sufficient strength at high temperatures.
c. The adhesive shall have good coating and thickness consistency.
d. The adhesive shall be used during its prescribed shelf life.
e. The adhesive shall harden rapidly.
f. The adhesive shall have corrosion resistance.
g. The adhesive shall have excellent insulation characteristics.
h. The adhesive shall have no emission of toxic gasses and no effect on the human body.
(2)The recommended amount of adhesives is as follows;
After capacitor are bonded
Amount adhesive
[Recommended condition]
a
a
Figure
212/316 case sizes as examples
a
0.3mm min
b
b
100 to 120μm
c
Adhesives shall not contact land
c
c
4. Soldering
Precautions
◆Selection of Flux
Since flux may have a significant effect on the performance of capacitors, it is necessary to verify the following conditions prior to use;
(1)Flux used shall be less than or equal to 0.1 wt%( in Cl equivalent) of halogenated content. Flux having a strong acidity content shall
not be applied.
(2)When shall capacitors are soldered on boards, the amount of flux applied shall be controlled at the optimum level.
(3)When water-soluble flux is used, special care shall be taken to properly clean the boards.
◆Soldering
Temperature, time, amount of solder, etc. shall be set in accordance with their recommended conditions.
Sn-Zn solder paste can adversely affect MLCC reliability.
Please contact us prior to usage of Sn-Zn solder.
Technical
considerations
◆Selection of Flux
1-1. When too much halogenated substance(Chlorine, etc.) content is used to activate flux, or highly acidic flux is used, it may lead to
corrosion of terminal electrodes or degradation of insulation resistance on the surfaces of the capacitors.
1-2. Flux is used to increase solderability in wave soldering. However if too much flux is applied, a large amount of flux gas may be emitted
and may adversely affect the solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system.
1-3. Since the residue of water-soluble flux is easily dissolved in moisture in the air, the residues on the surfaces of capacitors in high
humidity conditions may cause a degradation of insulation resistance and reliability of the capacitors. Therefore, the cleaning
methods and the capability of the machines used shall also be considered carefully when water-soluble flux is used.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
◆Soldering
・ Ceramic chip capacitors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling.
・ Therefore, the soldering must be conducted with great care so as to prevent malfunction of the components due to excessive thermal
shock.
・ Preheating : Capacitors shall be preheated sufficiently, and the temperature difference between the capacitors and solder shall be within
130℃.
・ Cooling : The temperature difference between the capacitors and cleaning process shall not be greater than 100℃.
[Reflow soldering]
【Recommended conditions for eutectic
soldering】
【Recommended condition for Pb-free
soldering】
300
300
200
Peak
260℃ Max.
Within 10sec.
230℃
Within 10sec.
60sec. 60sec
Min.
Min.
Slow cooling
100
Temperature(℃)
Temperature(℃)
Preheating
0
200
Slow
cooling
100
0
Preheating150℃ Heating above
230℃
60sec. Min.
40sec. Max.
1/2T~1/3T
Capacitor
Caution
①The ideal condition is to have solder mass(fillet)controlled to 1/2 to 1/3 of the
thickness of a capacitor.
②Because excessive dwell times can adversely affect solderability, soldering duration shall
be kept as close to recommended times as possible. soldering for 2 times.
[Wave soldering]
【Recommended conditions for eutectic
soldering】
300
100
Temperature(℃)
Temperature(℃)
Slow cooling
PC board
Peak
260℃ Max.
Within 10sec.
230~250℃
Within 3sec.
200
T
【Recommended condition for Pb-free
soldering】
300
Preheating
120sec. Min.
Solder
200
120sec. Min.
Preheating
150℃
100
Slow
cooling
0
0
Caution
①Wave soldering must not be applied to capacitors designated as for reflow soldering only. soldering for 1 times.
【Recommended condition for Pb-free
soldering】
400
400
300
200
Slow cooling
100
0
Preheating
60sec. Min.
Temperature(℃)
Temperature(℃)
300
⊿T
Slow cooling
200
Preheating
150℃ Min.
100
0
400
Peak
350℃ Max.
Within 3sec.
230~280℃
Within 3sec.
316type or less
200
0
Slow cooling
⊿T
Preheating
150℃ Min.
100
60sec. Min.
⊿T
⊿T≦150℃
Peak
280℃ Max.
Within 3sec.
300
温度(℃)
[Hand soldering]
【Recommended conditions for eutectic
soldering】
60sec. Min.
325type or more
⊿T
⊿T≦130℃
Caution
①Use a 50W soldering iron with a maximum tip diameter of 1.0 mm.
②The soldering iron shall not directly touch capacitors. soldering for 1 times.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
5. Cleaning
Precautions
Technical
considerations
◆Cleaning conditions
1. When PCBs are cleaned after capacitors mounting, please select the appropriate cleaning solution in accordance with the intended use
of the cleaning. (e.g. to remove soldering flux or other materials from the production process.)
2. Cleaning condition shall be determined after it is verified by using actual cleaning machine that the cleaning process does not affect
capacitor's characteristics.
1. The use of inappropriate cleaning solutions can cause foreign substances such as flux residue to adhere to capacitors or deteriorate
their outer coating, resulting in a degradation of the capacitor's electrical properties (especially insulation resistance).
2. Inappropriate cleaning conditions( insufficient or excessive cleaning) may adversely affect the performance of the capacitors.
In the case of ultrasonic cleaning, too much power output can cause excessive vibration of PCBs which may lead to the cracking of
capacitors or the soldered portion, or decrease the terminal electrodes' strength. Therefore, the following conditions shall be carefully
checked;
Ultrasonic output :
20 W/ℓ or les
Ultrasonic frequency :
40 kHz or less
Ultrasonic washing period : 5 min. or less
6. Resin coating and mold
Precautions
1. With some type of resins, decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while
left under normal storage conditions resulting in the deterioration of the capacitor's performance.
2. When a resin's hardening temperature is higher than capacitor's operating temperature, the stresses generated by the excessive heat
may lead to damage or destruction of capacitors.
The use of such resins, molding materials etc. is not recommended.
7. Handling
Precautions
◆Splitting of PCB
1. When PCBs are split after components mounting, care shall be taken so as not to give any stresses of deflection or twisting to the board.
2. Board separation shall not be done manually, but by using the appropriate devices.
◆Mechanical considerations
Be careful not to subject capacitors to excessive mechanical shocks.
(1)If ceramic capacitors are dropped onto a floor or a hard surface, they shall not be used.
(2)Please be careful that the mounted components do not come in contact with or bump against other boards or components.
8. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep packaging materials in good condition, care must be taken to control
temperature and humidity in the storage area. Humidity should especially be kept as low as possible.
・Recommended conditions
Ambient temperature : Below 30℃
Humidity : Below 70% RH
The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of capacitor is deteriorated as
time passes, so capacitors shall be used within 6 months from the time of delivery.
・Ceramic chip capacitors shall be kept where no chlorine or sulfur exists in the air.
2. The capacitance values of high dielectric constant capacitors will gradually decrease with the passage of time, so care shall be taken to
design circuits. Even if capacitance value decreases as time passes, it will get back to the initial value by a heat treatment at 150℃ for
1hour.
Technical
considerations
If capacitors are stored in a high temperature and humidity environment, it might rapidly cause poor solderability due to terminal oxidation and
quality loss of taping/packaging materials. For this reason, capacitors shall be used within 6 months from the time of delivery. If exceeding the
above period, please check solderability before using the capacitors.
※RCR-2335B(Safety Application Guide for fixed ceramic capacitors for use in electronic equipment)is published by JEITA.
Please check the guide regarding precautions for deflection test, soldering by spot heat, and so on.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01