LB2016T1R0M

厂商：
TAIYO-YUDEN(太诱)
封装：
描述：
LB2016T1R0M - WOUND CHIP INDUCTORS - Taiyo Yuden (U.S.A.), Inc

数据手册：

下载LB2016T1R0M.pdf

立即购买

数据手册
价格&库存

LB2016T1R0M 数据手册

Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2009. All of the contents speciﬁed herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those speciﬁed in this catalog or individual speciﬁcation. ■ Please contact Taiyo Yuden Co., Ltd. for further details of product speciﬁcations as the individual speciﬁcation is available. ■ Please conduct validation and veriﬁcation of products in actual condition of mounting and operating environment before commercial shipment of the equipment. ■ All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the ﬁeld such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct inﬂuence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in ﬁelds such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufﬁcient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. ■ The contents of this catalog are applicable to the products which are purchased from our sales ofﬁces or distribu“ tors (so called TAIYO YUDEN’ ofﬁcial sales channel” s ). It is only applicable to the products purchased from any of TAIYO YUDEN’ ofﬁcial sales channel. s ■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. ■ Caution for export Certain items in this catalog may require speciﬁc procedures for export according to“Foreign Exchange and Foreign Trade Control Law”of Japan,“U.S. Export Administration Regulations” and other applicable regulations. , Should you have any question or inquiry on this matter, please contact our sales staff. Should you have any question or inquiry on this matter, please contact our sales staff. 1 notice_e-01 WOUND CHIP INDUCTORS (LB SERIES) REFLOW ■ FEATURES Wound Chip Inductors cover customers' wide range module designs by wide-line-up shape, standard, low Rdc, and high electric current series. ◦ B/LBR Series：Super low Rdc and high Idc characteristics. L ◦ LB3218 Series ： This series is downsized from 3225 size. Land pattern can be used by 3225 size. ◦LBMF1608 The best efﬁciency design is achieved by adopting bottom-surface electrode structure. Because of 1608 shape, it can be high-density mounting. ■ APPLICATIONS ◦ SC/DVC/HDD, LCD, portable telephones, game equipments. D Various audio-visual equipments, various communication equipments, etc. ■ ORDERING CODE L ❶ LB B△ ❷ 2 0 ❸ 1 T 2 T ❹ 1 0 ❺ 0 △△△△△ ❻ ❼ ❼Special code Standard △ products Low Rdc R type ❽ ❽Internal code Standard Products △＝Blank space ❶Type Wound chip inductor ❷Shape Standard products High current Low Rdc Bottom-surface electrode △ C R MF ❸External Dimensions 〔mm〕 1608 0603） 1.6×0.8 （ 2012 0805） 2.0×1.25 （ 2016 0806） 2.0×1.6 （（ 2518 1007） 2.5×1.8 （ 3218 1207） 3.2×1.8 （ 3225 1210） 3.2×1.5 ❹Packaging Tape & Reel ❺Nominal Inductance μH〕〔 example 1R0 1 100 10 101 100 ※R=decimal point ❻Inductance Tolerances〔％〕 K ±10 M ±20 △△△ ■ E XTERNAL DIMENSIONS/STANDARD QUANTITY EXTERNAL DIMENSIONS C Type LBC3225 L W T e Standard Quantity [pcs] Paper Embossed Tape Tape －－－－－ 4000 － 1000 2000 2000 2000 2000 － 3000 Unit：mm inch）（ A B A 3.2±0.2 2.5±0.2 2.5±0.2 0.6±0.3 （0.128±0.008）（0.098±0.008）（0.098±0.008）（0.024±0.012） 3.2±0.2 1.8±0.2 1.8±0.2 0.6±0.2 （0.128±0.008）（0.071±0.008）（0.071±0.008）（0.024±0.008） 2.5±0.2 1.8±0.2 1.8±0.2 0.5±0.2 （0.098±0.008）（0.071±0.008）（0.071±0.008）（0.020±0.008） 2.0±0.2 1.6±0.2 1.6±0.2 0.5±0.2 （0.079±0.008）（0.063±0.008）（0.063±0.008）（0.020±0.008） 2.0±0.2 1.25±0.2 1.25±0.2 0.5±0.2 （0.079±0.008）（0.049±0.008）（0.049±0.008）（0.020±0.008） 1.6±0.1 0.8±0.1 0.8±0.1 0.35±0.15 （0.063±0.004）（0.031±0.004）（0.031±0.004）（0.014±0.006） 1.6±0.2 0.8±0.2 0.8±0.2 0.45±0.15 （0.063±0.008）（0.031±0.008）（0.031±0.008）（0.016±0.006） LB3218 Unit：mm C 1.0 0.9 1.45 1.8 2.0 2.0 2.0 LB2518 LBC2518 LBR2518 LB2016 LBC2016 LB2012 LBC2012 LBR2012 LB1608 LBMF1608 TYPE 1608 MF1608 2012 2016 2518 3218 3225 A 0.55 0.55 0.7 0.7 0.8 1.0 1.0 B 0.7 0.8 0.8 0.8 1.2 1.6 1.6 Surface Mounting ・ Mounting and soldering conditions should be checked beforehand. ・ A pplicable soldering process to those products is reﬂow soldering only. ・ Recommended Land Patterns ■ AVAILABLE CAPACITANCE RANGE Type Range LB3218 LB2518 LB2016 LB2012 LB1608 LBC3225 LBC2518 LBC2016 LBC2012 LBR2518 LBR2012 LBMF1608 Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％ Imax. mA］ Rdc±30％［　［Ω］［　［Ω］［　［Ω］［　［Ω］［　［Ω］［　［Ω］［　［Ω］［　［Ω］［　［Ω］［　［Ω］［　［Ω］［　［Ω］ 1 Inductance μH］［ 1075 1μH 0.06 665 1μH 0.06 490 1μH 0.09 405 1μH 0.15 160 1μH 0.17 1100 1μH 0.055 775 1μH 0.08 690 1μH 70 10 340 0.25 165 0.25 155 0.5 120 0.7 60 10μH 140 2.40 60 2.1 40 4.5 100μH 45 100μH 7.0 150 1.4 100μH 125 3.70 680μ 45 H 28.0 680μH 75 8.0 100μH 0.55 0.7 540 0.133 375 0.36 245 0.82 200 90 47μH 1.2 5.8 80 1.89 100μH 50 4.0 100μH 235 0.19 150 0.36 80 35 47μH 0.36 2.5 0.1 620 1μH 0.19 960 1μH 0.045 400 1μH 0.07 230 1μH 0.09 100 1000 40 27 1000μH 15 24 1000μH ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 42 1 wound01_e-01 ■ PART NUMBERS ●LB1608 TYPE Ordering code LB 1608T1R0M LB 1608T2R2M LB 1608T4R7M LB 1608T8R2M LB 1608T100M EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 2.2 4.7 8.2 10 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 45 32 32 DC Resistance 〔Ω〕±30％）（ 0.17 0.33 0.55 0.70 0.70 Rate d current 〔mA〕 ax. m 160 115 70 60 60 Measuring frequency 〔MHz〕 7.96 ±20% 2.52 ●LB2012 TYPE Ordering code LB 2012T1R0M LB 2012T2R2M LB 2012T3R3M LB 2012T4R7M LB 2012T6R8M LB 2012T100 □ LB 2012T100 □R LB 2012T150 □ LB 2012T220 □ LB 2012T470 □ LB 2012T680 □ LB 2012T101□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 2.2 3.3 4.7 6.8 10 10 15 22 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 55 45 38 32 32 28 16 11 10 8 DC Resistance 〔Ω〕±30％）（ 0.15 0.23 0.30 0.40 0.47 0.70 0.50 1.3 1.7 3.7 6.0 7.0 Rate d current 〔mA〕 ax. m 405 260 235 190 135 120 120 100 80 60 50 45 Measuring frequency 〔MHz〕 FERRITE PRODUCTS ±20% 7.96 ±10% ±20% 2.52 0.796 ●LB2016 T YPE Ordering code LB 2016T1R0M LB 2016T1R5M LB 2016T2R2M LB 2016T3R3M LB 2016T4R7M LB 2016T6R8M LB 2016T100 □ LB 2016T150 □ LB 2016T220 □ LB 2016T330 □ LB 2016T470 □ LB 2016T680 □ LB 2016T101□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 70 55 45 38 32 28 16 14 11 10 8 DC Resistance 〔Ω〕±30％）（ 0.09 0.11 0.13 0.20 0.25 0.35 0.50 0.70 1.0 1.7 2.4 3.0 4.5 Rate d current 〔mA〕 ax. m 490 380 375 285 225 200 155 130 105 85 70 55 40 Measuring frequency 〔MHz〕 ±20% 7.96 ±10% ±20% 2.52 0.796 ●LB2518 T YPE EHS （Environmental Hazardous Substances） LB 2518T1R0M RoHS LB 2518T1R5M RoHS LB 2518T2R2M RoHS LB 2518T3R3M RoHS LB 2518T4R7M RoHS LB 2518T4R7MR RoHS LB 2518T6R8M RoHS LB 2518T100 □ RoHS LB 2518T150 □ RoHS LB 2518T220 □ RoHS LB 2518T330 □ RoHS LB 2518T470 □ RoHS LB 2518T680 □ RoHS LB 2518T101□ RoHS LB 2518T151□ RoHS LB 2518T221□ RoHS LB 2518T331□ RoHS LB 2518T471□ RoHS LB 2518T681□ RoHS LB 2518T102□ RoHS ・□Please specify the Inductance tolerance code K or M）（ Ordering code Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 100 0 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 68 54 46 46 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 3.5 3.0 2.4 DC Resistance 〔Ω〕±30％）（ 0.06 0.07 0.09 0.11 0.13 0.10 0.15 0.25 0.32 0.50 0.70 0.95 1.5 2.1 3.2 4.5 7.0 10 17 24 Rate d current 〔mA〕 ax. m 665 405 340 280 240 235 195 165 145 115 95 85 70 60 45 40 30 25 20 15 Measuring frequency 〔MHz〕 ±20% 7.96 2.52 ±10% ±20% 0.796 0.252 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound01_e-01 1 43 ■ PART NUMBERS ●LB3218 TYPE Ordering code LB 3218T1R0M LB 3218T1R5M LB 3218T2R2M LB 3218T3R3M LB 3218T4R7M LB 3218T6R8M LB 3218T100 □ LB 3218T150 □ LB 3218T220 □ LB 3218T330 □ LB 3218T470 □ LB 3218T680 □ LB 3218T101□ LB 3218T151□ LB 3218T221□ LB 3218T331□ LB 3218T471□ LB 3218T681□ LB 3218T102□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1000 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 68 54 41 40 30 25 19 15 12 11 8.0 7.0 5.0 4.0 3.5 3.0 2.4 DC Resistance 〔Ω〕±30％）（ 0.06 0.07 0.09 0.11 0.13 0.17 0.25 0.32 0.49 0.75 0.92 1.49 2.4 3.2 5.4 7.0 14 17 27 Rate d current 〔mA〕 ax. m 1075 860 775 560 550 380 340 300 255 215 205 145 140 105 80 65 54 45 39 Measuring frequency 〔MHz〕 ±20% 7.96 2.52 ±10% ±20% 0.796 0.252 ●LBMF1608 TYPE Ordering code LBMF1608T1R0M LBMF1608T2R2M LBMF1608T3R3M LBMF1608T4R7M LBMF1608T100 □ LBMF1608T220 □ LBMF1608T470 □ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 2.2 3.3 4.7 10 22 47 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 60 45 32 16 11 DC Resistance 〔Ω〕±30％）（ 0.09 0.17 0.22 0.24 0.36 1.0 2.5 Rate d current 〔mA〕 ax. m 230 160 130 110 80 50 35 Measuring frequency 〔MHz〕 ±20% 7.96 ±10% ±20% 2.52 ●LBC3225 TYPE Ordering code LB C3225T1R0MR LB C3225T1R5MR LB C3225T2R2MR LB C3225T3R3MR LB C3225T4R7MR LB C3225T6R8MR LB C3225T100 □R LB C3225T150 □R LB C3225T220 □R LB C3225T330 □R LB C3225T470 □R LB C3225T680 □R LB C3225T101□R EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 250 220 190 160 70 50 23 20 17 13 10 8 6 DC Resistance 〔Ω〕±30％）（ 0.055 0.060 0.080 0.095 0.100 0.120 0.133 0.195 0.270 0.410 0.670 1.00 1.40 Rate d current 〔mA〕 ax. m 1100 1000 930 820 680 620 540 420 330 300 220 190 150 Measuring frequency 〔MHz〕 ±20% 0.1 ±10% ±20% ●LBC2518 TYPE EHS （Environmental Hazardous Substances） LB C2518T1R0M RoHS LB C2518T1R0MR RoHS LB C2518T1R5M RoHS LB C2518T2R2M RoHS LB C2518T3R3M RoHS LB C2518T4R7M RoHS LB C2518T6R8M RoHS LB C2518T100 □ RoHS LB C2518T150 □ RoHS LB C2518T220 □ RoHS LB C2518T330 □ RoHS LB C2518T470 □ RoHS LB C2518T680 □ RoHS LB C2518T101□ RoHS LB C2518T151□ RoHS LB C2518T221□ RoHS LB C2518T331□ RoHS LB C2518T471□ RoHS LB C2518T681□ RoHS ・□Please specify the Inductance tolerance code K or M）（ Ordering code Inductance 〔μH〕 1.0 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 100 80 68 54 41 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 4.5 3.0 DC Resistance 〔Ω〕±30％）（ 0.08 0.065 0.11 0.13 0.16 0.20 0.30 0.36 0.65 0.77 1.5 1.9 2.8 3.7 6.1 8.4 12.3 22 28 Rate d current 〔mA〕 ax. m 775 890 730 630 560 510 420 375 285 250 185 165 140 125 95 80 65 50 45 Measuring frequency 〔MHz〕 ±20% 7.96 2.52 ±10% ±20% 0.796 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 44 1 wound01_e-01 ■ PART NUMBERS ●LBC2016 TYPE Ordering code LB C2016T1R0M LB C2016T1R5M LB C2016T2R2M LB C2016T3R3M LB C2016T4R7M LB C2016T6R8M LB C2016T100 □ LB C2016T150 □ LB C2016T220 □ LB C2016T330 □ LB C2016T470 □ LB C2016T680 □ LB C2016T101□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 70 55 45 38 32 28 16 14 11 10 8 DC Resistance 〔Ω〕±30％）（ 0.10 0.15 0.20 0.27 0.37 0.59 0.82 1.2 1.8 2.8 4.3 7.0 8.0 Rate d current 〔mA〕 ax. m 690 600 520 410 355 290 245 200 165 135 110 95 75 Measuring frequency 〔MHz〕 ±20% 7.96 ±10% ±20% 2.52 0.796 FERRITE PRODUCTS ●LBC2012 TYPE Ordering code LB C2012T1R0M LB C2012T2R2M LB C2012T4R7M LB C2012T100 □ LB C2012T220 □ LB C2012T470 □ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 2.2 4.7 10 22 47 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 70 45 40 16 11 DC Resistance 〔Ω〕±30％）（ 0.19 0.33 0.50 1.2 3.7 5.8 Rate d current 〔mA〕 ax. m 620 430 295 200 130 90 Measuring frequency 〔MHz〕 7.96 ±20% ±10% ±20% 2.52 ●LBR2518 TYPE Ordering code LB R 2518T1R0M LB R2518T2R2M LB R2518T4R7M LB R2518T100 □ LB R2518T220 □ LB R2518T470 □ LB R2518T101□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 2.2 4.7 10 22 47 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 68 45 30 19 11 9 DC Resistance 〔Ω〕±30％）（ 0.045 0.07 0.10 0.19 0.44 0.84 1.89 Rate d current 〔mA〕 ax. m 960 480 345 235 175 120 80 Measuring frequency 〔MHz〕 7.96 ±20% ±10% ±20% 2.52 0.796 ●LBR2012 TYPE EHS （Environmental Hazardous Substances） LB R 2012T1R0M RoHS LB R2012T2R2M RoHS LB R2012T4R7M RoHS LB R2012T100 □ RoHS LB R2012T220 □ RoHS LB R2012T470 □ RoHS LB R2012T101□ RoHS ・□Please specify the Inductance tolerance code K or M）（ Ordering code Inductance 〔μH〕 1.0 2.2 4.7 10 22 47 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 45 32 16 11 8 DC Resistance 〔Ω〕±30％）（ 0.07 0.13 0.24 0.36 1.0 1.7 4.0 Rate d current 〔mA〕 ax. m 400 260 200 150 100 75 50 Measuring frequency 〔MHz〕 7.96 ±20% ±10% ±20% 2.52 0.796 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound01_e-01 1 45 ■ ELECTRICAL CHARACTERISTICS （ ■DC Bias characteristics Measured by HP4285A＋42841A） LB1608 100 1000 101□ Inductance 〔μH〕 LB2012 1000 LB2016 1000 Standard Type LB2518 Inductance 〔μH〕 Inductance 〔μH〕 10 10 100□ 10 100□ Inductance 〔μH〕 100M 100 100 101□ 100 101□ 10 100□ 1 1R0M 1 1R0M 1 1R0M 1 1R0M 0.1 1 10 100 DC Bias 〔mA〕 1000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 Standard Type LB3218 1000 100 470□ 100 101□ Inductance 〔μH〕 10 100□ 100 LBC2012 1000 High Current Type LBC2016 1000 101□ Inductance 〔μH〕 LBC2518 Inductance 〔μH〕 Inductance 〔μH〕 100 101□ 10 100□ 10 100□ 10 100□ 1R0M 1 1 1R0M 1 1R0M 1 1R0M 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 0.1 1 10 100 DC Bias 〔mA〕 1000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 High Current Type ＬＣ3225 Ｂ 100 101□Ｒ 1000 LBR2012 Low Rdc Type LBR2518 1000 Bottom-surface electrode Type LBMF1608 10 100□ 4R7M Inductance 〔μH〕 Inductance 〔μH〕 Inductance 〔μH〕 10 100□Ｒ 100 Inductance 〔μH〕 101□ 100 101□ 100□ 10 1 1R0M 1 1R0MR 10 100□ 1 1R0M 1R0M 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 1 1 10 100 DC Bias 〔mA〕 1000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 0.1 1 10 100 DC Bias 〔mA〕 1000 （ ■Impedance-vs-Frequency characteristics Measured by HP4291A） LB1608 10000 100M 1000 1R0M 10000 Impedance 〔Ω〕 1000 100 100000 LB2012 101□ 100□ 1R0M 100000 10000 Impedance 〔Ω〕 1000 100 101□ 100□ 1R0M LB2016 Standard Type LB2518 100000 10000 Impedance 〔Ω〕 1000 100 10 1 101□ 100□ 1R0M Impedance 〔Ω〕 100 10 10 1 10 1 1 1 10 100 1000 Frequency 〔MHz〕 10000 1 10 100 1000 Frequency 〔MHz〕 10000 1 10 100 1000 Frequency 〔MHz〕 10000 1 10 100 1000 Frequency 〔MHz〕 10000 Standard Type LB3218 100000 101□ 10000 Impedance 〔Ω〕 1000 100 10 1 100□ 1R0M 10000 Impedance 〔Ω〕 1000 100 10 1 100000 470□ 100□ 1R0M 10000 Impedance 〔Ω〕 LBC2012 100000 High Current Type LBC2016 101□ 100□ 1R0M 1000 100 10 1 100000 101□ LBC2518 10000 Impedance 〔Ω〕 1000 100□ 1R0M 100 10 1 1 10 100 1000 Frequency 〔MHz〕 10000 1 10 100 1000 Frequency 〔MHz〕 10000 1 10 100 1000 Frequency 〔MHz〕 10000 1 10 100 1000 Frequency 〔MHz〕 10000 High Current Type LBC3325 100000 10000 Impedance 〔Ω〕 1000 100 10 1 0.1 0.1 101□R 100□R 1R0MR Low Rdc Type LBR2012 100000 101□ 10000 Impedance 〔Ω〕 1000 100 10 1 100□ 1R0M 10000 Impedance 〔Ω〕 1000 100 10 1 100000 101□ 100□ 1R0M LBR2518 Bottom-surface electrode Type LBMF1608 100000 470□ 10000 Impedance 〔Ω〕 100□ 4R7M 1000 100 10 1 1 10 100 1000 10000 Frequency 〔MHz〕 1 10 100 1000 Frequency 〔MHz〕 10000 1 10 100 1000 Frequency 〔MHz〕 10000 1 10 100 1000 Frequency 〔MHz〕 10000 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 46 1 wound01_e-01 WOUND CHIP POWER INDUCTORS (CB SERIES) REFLOW ■ FEATURES ◦ his series corresponds to high electric current compared with LB/ T LBC series. Wound Chip Inductors that can be used for small DC/DC converters and are suitable for choke uses. ◦ BMF 1608 Series C The best efﬁciency design is achieved by adopting bottom-surface electrode structure. Wound C hip Inductors that are suitable for module design which needs high electric current like DC/DC converters. ■ APPLICATIONS ◦ SC/DVC/HDD, LCD, portable telephones, game equipment. D Various audio-visual equipment, various communication equipment, etc. ■ ORDERING CODE C ❶ CB B△ ❷ 2 0 ❸ 1 T 2 T ❹ 1 0 ❺ 0 △△△△△ ❻ ❼ ❼Special code Standard △ products Low Rdc R type ❽ ❽Internal code Standard Products △＝Blank space ❶Type Wound chip power inductor ❷Characteristic Spec Low Rdc High current Low proﬁle Bottom-surface electrode △ C L MF ❸External Dimensions 〔mm〕 1608 0603） 1.6×0.8 （ 2012 0805） 2.0×1.25 （ 2016 0806） 2.0×1.6 （（ 2518 1007） 2.5×1.8 （ 3225 1210） 3.2×2.5 ❹Packaging Tape & Reel ❺Nominal Inductance μH〕〔 example 1R0 1 100 10 101 100 ※R=decimal point ❻Inductance Tolerances ％〕〔 K ±10 M ±20 △△△ ■ E XTERNAL DIMENSIONS/STANDARD QUANTITY Type C L W T e Standard Quantity [pcs] Paper Embossed Tape Tape －－－－ 4000 － 1000 2000 2000 2000 － 3000 Unit：mm inch）（ CBC3225 A B A 3.2±0.2 2.5±0.2 2.5±0.2 0.6±0.3 （0.126±0.008）（0.098±0.008）（0.098±0.008）（0.024±0.012） 2.5±0.2 1.8±0.2 1.8±0.2 0.5±0.2 （0.098±0.008）（0.071±0.008）（0.071±0.008）（0.020±0.008） 2.0±0.2 1.6±0.2 1.6±0.2 0.5±0.2 （0.079±0.008）（0.063±0.008）（0.063±0.008）（0.020±0.008） 2.0±0.2 1.25±0.2 1.25±0.2 0.5±0.2 （0.079±0.008）（0.049±0.008）（0.049±0.008）（0.020±0.008） 2.0±0.2 1.25±0.2 0.9±0.1 0.5±0.2 （0.079±0.008）（0.049±0.008）（0.035±0.004）（0.020±0.008） 1.6±0.2 0.8±0.2 0.8±0.2 0.45±0.15 （0.063±0.2）（0.031±0.008）（0.031±0.008）（0.016±0.006） CB2518 CBC2518 CB2016 CBC2016 CB2012 CBC2012 CBL2012 CBMF1608 TYPE 1608 MF1608 2012 2016 2518 3225 A 0.55 0.55 0.7 0.7 0.8 1.0 B 0.7 0.8 0.8 0.8 1.2 1.6 Unit：mm C 1.0 0.9 1.45 1.8 2.0 2.0 Recommended Land Patterns Surface Mounting ・ Mounting and soldering conMounting ditions should be checked beforehand. ・ A pplicable soldering process to those products is reﬂow soldering only. ・ Recommended Land Patterns ■ AVAILABLE CAPACITANCE RANGE Type Range CB2518 CB2016 CB2012 CBC3225 CBC2518 CBC2016 CBC2012 CBC2012 CBMF1608 Imax mA］ Rdc±30％［Ω］ Imax mA］ Rdc±30％［Ω］ Imax mA］ Rdc±30％［Ω］ Imax mA］ Rdc±30％［Ω］ Imax mA］ Rdc±30％［Ω］ Imax mA］ Rdc±30％［Ω］ Imax mA］ Rdc±30％［Ω］ Imax mA］ Rdc±30％［Ω］ Imax mA］ Rdc±30％［Ω］［　［　［　［　［　［　［　［　［　 1 1200 1μH 0.06 600 1μH 0.09 500 1μH 0.15 1440 1μH 0.055 1000 1μH 0.08 1100 1μH 0.1 700 1μH 0.19 620 1μH 0.15 350 1μH 0.09 22 510 10 250 47 110 100 60 0.09 2.40 0.95 2.1 510 250 110 70 100μH 1000 25 1000μH 24 0.13 0.5 2.4 4.5 410 200 90 60 100μH 0.23 0.5 3.7 7 1130 900 390 270 100μH 0.08 0.133 0.67 1.4 890 480 240 160 65 680μH 0.13 0.36 1.90 3.7 28 750 380 150 110 100μH 0.2 0.82 4.3 8 530 240 120 47μH 0.33 1.2 5.8 530 440 100 47μH 0.33 1.0 4.2 230 115 50 47μH 0.17 0.36 2.5 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. Inductance μH］［ 48 1 wound02_e-01 ■ PART NUMBERS ●CB2012 TYPE Ordering code CB 2012T1R0M CB 2012T2R2M CB 2012T3R3M CB 2012T4R7M CB 2012T6R8M CB 2012T100□ CB 2012T100□R CB 2012T150□ CB 2012T220□ CB 2012T470□ CB 2012T680□ CB 2012T101□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 2.2 3.3 4.7 6.8 10 10 15 22 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 55 45 38 32 32 28 16 11 10 8 Resistance DC 〔Ω（±30％）〕 0.15 0.23 0.30 0.40 0.47 0.70 0.50 1.3 1.7 3.7 6.0 7.0 Saturation current Idc1 Rated current mA〕〔 Temperature rise current Idc2 500 900 410 770 330 650 300 580 250 540 190 440 200 520 170 320 135 280 90 190 70 140 60 130 Measuring frequency 〔MHz〕 ±20% 7.96 ±10% ±20% 2.52 0.796 FERRITE PRODUCTS ●CB2016 T YPE Ordering code CB 2016T1R0M CB 2016T1R5M CB 2016T2R2M CB 2016T3R3M CB 2016T4R7M CB 2016T6R8M CB 2016T100□ CB 2016T150□ CB 2016T220□ CB 2016T330□ CB 2016T470□ CB 2016T680□ CB 2016T101□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 70 55 45 38 32 28 16 14 11 10 8 Resistance DC 〔Ω（±30％）〕 0.09 0.11 0.13 0.20 0.25 0.35 0.50 0.70 1.0 1.7 2.4 3.0 4.5 Saturation current Idc1 Rated current mA〕〔 Temperature rise current Idc2 600 1100 550 1000 510 1000 400 800 340 740 300 600 250 520 210 440 165 370 130 270 110 240 90 210 70 170 Measuring frequency 〔MHz〕 ±20% 7.96 ±10% ±20% 2.52 0.796 ●CB2518 T YPE Ordering code CB 2518T1R0M CB 2518T1R5M CB 2518T2R2M CB 2518T3R3M CB 2518T4R7MR CB 2518T4R7M CB 2518T6R8M CB 2518T100 □ CB 2518T150 □ CB 2518T220 □ CB 2518T330 □ CB 2518T470 □ CB 2518T680 □ CB 2518T101□ CB 2518T151□ CB 2518T221□ CB 2518T331□ CB 2518T471□ CB 2518T681□ CB 2518T102□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 100 0 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 68 54 46 46 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 3.5 3.0 2.4 Resistance DC 〔Ω（±30％）〕 0.06 0.07 0.09 0.11 0.10 0.13 0.15 0.25 0.32 0.50 0.70 0.95 1.5 2.1 3.2 4.5 7.0 10 17 24 Saturation current Idc1 Rated current mA〕〔 Temperature rise current Idc2 1200 1500 650 1400 510 1300 440 1200 310 1200 340 1100 270 930 250 820 180 650 165 580 130 460 110 420 70 310 60 260 55 210 50 180 40 140 35 120 30 90 25 75 Measuring frequency 〔MHz〕 ±20% 7.96 2.52 ±10% ±20% 0.796 0.252 ●CBC2012 TYPE Ordering code CB C2012T1R0M CB C2012T2R2M CB C2012T4R7M CB C2012T100 □ CB C2012T220 □ CB C2012T470 □ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 2.2 4.7 10 22 47 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 70 45 40 16 11 Resistance DC 〔Ω（±30％）〕 0.19 0.33 0.50 1.2 3.7 5.8 Saturation current Idc1 Rated current mA〕〔 Temperature rise current Idc2 700 840 530 640 360 520 240 340 170 190 120 150 Measuring frequency 〔MHz〕 ±20% ±10% ±20% 7.96 2.52 ・ Please specify the Inductance tolerance code Ｋor Ｍ） □ （ ※） e saturation current value Idc1）s the DC current value having inductance decrease down to 30%. at 20℃） Th （ i （（ ※） temperature rise current value Idc2）s the DC current value having temperature increase up to 40℃. at 20℃） The （ i ※） maximum rated current is the DC current value that satisﬁes both of DC saturation current value and temperature rise current value. The ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound02_e-01 1 49 ■ PART NUMBERS ●CBC2016 TYPE Ordering code CB C2016T1R0M CB C2016T1R5M CB C2016T2R2M CB C2016T3R3M CB C2016T4R7M CB C2016T6R8M CB C2016T100□ CB C2016T150□ CB C2016T220□ CB C2016T330□ CB C2016T470□ CB C2016T680□ CB C2016T101□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 70 55 45 38 32 28 16 14 11 10 8 Resistance DC 〔Ω（±30％）〕 0.10 0.15 0.20 0.27 0.37 0.59 0.82 1.2 1.8 2.8 4.3 7.0 8.0 Rated current mA〕〔 Temperature rise current Idc2 1100 1100 1000 1000 750 720 600 610 550 530 450 450 380 350 300 300 250 240 220 220 150 150 130 130 110 110 Measuring frequency 〔MHz〕 Saturation current Idc1 ±20% 7.96 ±10% ±20% 2.52 0.796 ●CBC2518 TYPE Ordering code CB C2518T1R0M CB C2518T1R5M CB C2518T2R2M CB C2518T3R3M CB C2518T4R7M CB C2518T6R8M CB C2518T100□ CB C2518T150□ CB C2518T220□ CB C2518T330□ CB C2518T470□ CB C2518T680□ CB C2518T101□ CB C2518T151□ CB C2518T221□ CB C2518T331□ CB C2518T471□ CB C2518T681□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 68 54 41 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 3.5 3.0 Resistance DC 〔Ω（±30％）〕 0.08 0.11 0.13 0.16 0.20 0.30 0.36 0.65 0.77 1.5 1.9 2.8 3.7 6.1 8.4 12.3 22 28 Rated current mA〕〔 Temperature rise Saturation current current Idc1 Idc2 1000 1200 950 1190 890 1100 730 1020 680 920 550 740 480 680 350 500 320 460 270 320 240 290 200 200 160 170 140 130 110 115 100 90 80 70 65 60 Measuring frequency 〔MHz〕 ±20% 7.96 2.52 ±10% ±20% 0.796 ●CBC3225 TYPE Ordering code CB C3225T1R0MR CB C3225T1R5MR CB C3225T2R2MR CB C3225T3R3MR CB C3225T4R7MR CB C3225T6R8MR CB C3225T100□R CB C3225T150□R CB C3225T220□R CB C3225T330□R CB C3225T470□R CB C3225T680□R CB C3225T101□R EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 250 220 190 160 70 50 23 20 17 13 10 8 6 Resistance DC 〔Ω（±30％）〕 0.055 0.06 0.08 0.095 0.10 0.12 0.133 0.195 0.27 0.41 0.67 1.0 1.4 Rated current mA〕〔 Temperature rise current Idc2 2000 1440 2000 1310 2000 1130 2000 1040 1250 1010 950 940 900 900 730 850 620 780 500 570 390 480 320 410 270 340 Measuring frequency 〔MHz〕 Saturation current Idc1 ±20% 0.1 ±10% ±20% ●CBL2012 TYPE Ordering code CB L2012T1R0M CB L2012T2R2M CB L2012T4R7M CB L2012T100M CB L2012T220M CB L2012T470M EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 2.2 4.7 10 22 47 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 45 32 23 11 Resistance DC 〔Ω（±30％）〕 0.15 0.39 0.66 1.0 2.1 4.2 Rated current mA〕〔 Temperature rise current Idc2 620 950 440 590 275 490 205 370 150 250 100 140 Measuring frequency 〔MHz〕 Saturation current Idc1 ±20% 0.1 ・□Please specify the Inductance tolerance code Ｋor Ｍ）（ ※） saturation current value Idc1）s the DC current value having inductance decrease down to 30%. at 20℃） The （ i （（ ※） temperature rise current value Idc2）s the DC current value having temperature increase up to 40℃. at 20℃） The （ i ※） maximum rated current is the DC current value that satisﬁes both of DC saturation current value and temperature rise current value. The ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 50 1 wound02_e-01 ■ PART NUMBERS ●CBMF1608 TYPE Ordering code CBMF1608T1R0M CBMF1608T2R2M CBMF1608T3R3M CBMF1608T4R7M CBMF1608T100□ CBMF1608T220□ CBMF1608T470□ EHS （Environmental Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 1.0 2.2 3.3 4.7 10.0 22 47 Inductance Tolerance Self-resonant frequency 〔MHz〕 min. 100 80 60 45 32 16 11 Resistance DC 〔Ω（±30％）〕 0.09 0.17 0.22 0.24 0.36 1.0 2.5 Rated current mA〕〔 Temperature rise current Idc2 290 770 190 560 170 500 145 470 115 380 70 230 50 140 Measuring frequency 〔MHz〕 Saturation current Idc1 ±20% 7.96 ±10% ±20% 2.52 ・ Please specify the Inductance tolerance code Ｋor Ｍ） □ （（ ※） e saturation current value Idc1）s the DC current value having inductance decrease down to 30%. at 20℃） Th （ i （ ※） temperature rise current value Idc2）s the DC current value having temperature increase up to 40℃. at 20℃） The （ i ※） maximum rated current is the DC current value that satisﬁes both of DC saturation current value and temperature rise current value. The FERRITE PRODUCTS ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound02_e-01 1 51 ■ ELECTRICAL CHARACTERISTICS ■DC Bias characteristics　Measured by HP4285A＋42841A CB2012 1000 101□ Inductance 〔μH〕 1000 101□ Inductance 〔μH〕 CB2016 1000 101□ Low Rdc Type CB2518 Inductance 〔μH〕 100 100 100 10 100□ 10 100□ 10 100□ 1 1R0M 1 1R0M 1 1R0M 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 High Current Type CBC2012 100 470□ 1000 101□ Inductance 〔μH〕 CBC2016 1000 101□ Inductance 〔μH〕 10 100□R CBC2518 100 CBC3225 101□R Inductance 〔μH〕 10 Inductance 〔μH〕 100□ 100 100 10 100□ 10 100□ 1R0M 1 1 1R0M 1 1R0M 1 1R0MR 0.1 1 10 100 DC Bias 〔mA〕 1000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 0.1 1 10 100 1000 DC Bias 〔mA〕 10000 Low Proﬁle Type CBL2012 100 470M Inductance 〔μH〕 Inductance 〔μH〕 Bottom-surface electrode Type CBMF1608 100 100□ 4R7M 10 100M 4R7M 10 1R0M 1 1 10 100 DC Bias 〔mA〕 1000 1 1 10 100 DC Bias 〔mA〕 1000 ■Impedance-vs-Frequency characteristics　Measured by HP4291A CB2012 100000 10000 Impedance 〔Ω〕 101□ 100□ 1R0M 1000 100 10 1 100000 10000 Impedance 〔Ω〕 1000 100 10 1 CB2016 101□ 100□ 1R0M Low Rdc Type CB2518 100000 10000 Impedance 〔Ω〕 1000 100 10 1 101□ 100□ 1R0M 1 10 100 1000 Frequency 〔MHz〕 10000 1 100 1000 10 Frequency 〔MHz〕 10000 1 100 1000 10 Frequency 〔MHz〕 10000 High Current Type CBC2012 100000 470□ 10000 Impedance 〔Ω〕 1000 100 10 1 100□ 1R0M 10000 Impedance 〔Ω〕 1000 100 10 1 100000 CBC2016 101□ 100□ 1R0M 100000 101□ 10000 Impedance 〔Ω〕 1000 100 10 1 100□ 1R0M 10000 Impedance 〔Ω〕 1000 100 10 1 CBC2518 100000 CBC3225 101□R 100□R 1R0MR 1 100 1000 10 Frequency 〔MHz〕 10000 1 100 1000 10 Frequency 〔MHz〕 10000 1 100 1000 10 Frequency 〔MHz〕 10000 1 100 1000 10 Frequency 〔MHz〕 10000 Low Proﬁle Type CBL2012 100000 470M 10000 Impedance 〔Ω〕 1000 100 10 1 100M 4R7M Bottom-surface electrode Type CBMF1608 100000 10000 Impedance 〔Ω〕 1000 100 10 1 470□ 100□ 4R7M 1 100 10 Frequency 〔MHz〕 1000 1 10 100 1000 Frequency 〔MHz〕 10000 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 52 1 wound02_e-01 WOUND CHIP INDUCTORS FOR SIGNAL LINE (LB/LE SERIES M TYPE) LB： REFLOW LE： WAVE REFLOW ■ FEATURES ◦ BM2016 Series L High Q and narrow tolerance are achieved by adopting bottom-surface electrode structure.Wound Chip Inductors that are suitable for module design of signal line uses. ◦ EM2520 Series L A high-quality inductor that is simple to mass-produce and conforms to the same production process and basic construction as an axial lead type inductor. ■ APPLICATIONS ◦ SC/DVC/HDD, LCD, portable telephones, game equipment. D Various audio-visual equipment, various communication equipment, etc. ■ ORDERING CODE L BM ❶ 2 0 ❷ 1 6 T T ❸ ❸Packaging Tape & Reel 1 0 ❹ 0 J△ ❺ ❻ ❻Internal code Standard Products △＝Blank space LBM ❶Type Wound chip inductor for signal line Wound chip inductor for LEM signal line ❷External Dimensions mm〕〔 2016 2.0×1.6 2520 2.5×2.0 ❹Nominal Inductance μH〕〔 example R12 0.12 1R0 1.00 100 10.0 ※R=decimal point ❺Inductance Tolerances J ±5% K ±10% △ ■ E XTERNAL DIMENSIONS/STANDARD QUANTITY LBM2016 LEM2520 ■ AVAILABLE CAPACITANCE RANGE Type Range 0.12 Ordinary type Inductance μH］［ LBM2016 Idc mA］［ 610 LEM2520 Rdc±30％［Ω］ 0.37 Rdc±30％［Ω］ Idc mA］［ 0.13 520 1.0 385 0.38 245 1.10 e e 10 215 1.20 155 3.50 Type LBM2016 L W T e W Standard Quantity [pcs] Paper Tape Embossed Tape － 2000 100 80 8.00 100μH 60 21.00 100μH 2.0±0.2 1.6±0.2 1.6±0.2 0.5±0.2 （0.08±0.008）（0.063±0.008）（0.063±0.008）（0.02±0.008） 2.5±0.2 2.0±0.2 1.8±0.2 0.45 1.4±0.1 LEM2520 （0.098±0.008）（0.079±0.008）（0.071±0.008）（0.018）（0.055±0.004） Unit：mm inch）（ Recommended Land Patterns Surface Mounting ・Mounting and soldering conditions should be checked beforehand. （・ Applicable soldering process to those products is reﬂow soldering only. LB only）・Recommended Land Pat terns C Unit：mm A B A TYPE LBM2016 LEM2520 A 0.7 0.9 B 0.8 1.5 C 1.8 1.5 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 54 1 wound03_e-01 ■ PART NUMBERS ●LBM2016 TYPE Ordering code LB M2016TR12J LB M2016TR15J LB M2016TR18J LB M2016TR22J LB M2016TR27J LB M2016TR33J LB M2016TR39J LB M2016TR47J LB M2016TR56J LB M2016TR68J LB M2016TR82J LB M2016T1R0J LB M2016T1R2J LB M2016T1R5J LB M2016T1R8J LB M2016T2R2J LB M2016T2R7J LB M2016T3R3J LB M2016T3R9J LB M2016T4R7J LB M2016T5R6J LB M2016T6R8J LB M2016T8R2J LB M2016T100J LB M2016T120J LB M2016T150J LB M2016T180J LB M2016T220J LB M2016T270J LB M2016T330J LB M2016T390J LB M2016T470J LB M2016T560J LB M2016T680J LB M2016T820J LB M2016T101J EHS Environmental （ Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 Inductance Tolerance Q （min.） Self-resonant frequency 〔MHz〕 in. m 600 550 500 450 425 400 375 350 300 270 250 220 180 135 100 75 55 48 43 40 36 33 30 27 23 20 18 17 16 15 14 13 12 11 10 9.0 Resistance DC 〔Ω〕±30％）（ 0.13 0.15 0.15 0.20 0.21 0.21 0.26 0.26 0.29 0.32 0.34 0.38 0.41 0.47 0.48 0.54 0.59 0.68 0.74 0.78 0.88 0.97 1.10 1.20 1.4 1.5 2.5 2.8 3.2 3.6 3.9 4.1 5.9 7.0 7.7 8.0 Rated current 〔mA〕（max.） 610 570 560 520 510 490 440 430 410 400 390 385 370 350 345 340 310 290 275 270 255 240 225 215 200 190 150 140 130 125 120 115 95 90 85 80 Measuring frequency 〔MHz〕 25.2 30 FERRITE PRODUCTS 7.96 ±5％ 25 2.52 20 15 0.796 ●LEM2520 TYPE Ordering code LEM 2520 TR12K LEM 2520 TR15K LEM 2520 TR18K LEM 2520 TR22K LEM 2520 TR27K LEM 2520 TR33K LEM 2520 TR39K LEM 2520 TR47K LEM 2520 TR56K LEM 2520 TR68K LEM 2520 TR82K LEM 2520 T1R0J LEM 2520 T1R2J LEM 2520 T1R5J LEM 2520 T1R8J LEM 2520 T2R2J LEM 2520 T2R7J LEM 2520 T3R3J LEM 2520 T3R9J LEM 2520 T4R7J LEM 2520 T5R6J LEM 2520 T6R8J LEM 2520 T8R2J LEM 2520 T100J LEM 2520 T120J LEM 2520 T150J LEM 2520 T180J LEM 2520 T220J LEM 2520 T270J LEM 2520 T330J LEM 2520 T390J LEM 2520 T470J LEM 2520 T560J LEM 2520 T680J LEM 2520 T820J LEM 2520 T101J EHS Environmental （ Hazardous Substances） RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance 〔μH〕 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 Inductance Tolerance Q （min.） Self-resonant frequency 〔MHz〕 in. m 600 550 500 450 425 400 375 350 300 270 250 220 180 135 100 75 55 48 43 40 36 33 30 27 23 20 18 17 16 15 14 13 12 11 10 9 Resistance DC 〔Ω〕±30％）（ 0.37 0.42 0.46 0.52 0.56 0.60 0.65 0.68 0.75 0.85 1.00 1.10 1.20 1.30 1.45 1.55 1.70 1.90 2.10 2.30 2.50 2.70 3.05 3.50 3.80 4.40 4.80 5.50 6.30 7.10 9.50 11.10 12.10 16.60 19.00 21.00 Rated current 〔mA〕（max.） 520 480 460 430 420 400 375 350 325 300 260 245 230 220 210 200 195 185 180 175 170 165 160 155 150 140 130 125 115 110 90 80 75 70 65 60 Measuring frequency 〔MHz〕 ±10％ 25.2 30 7.96 ±5％ 25 2.52 20 15 0.796 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound03_e-01 1 55 ■ ELECTRICAL CHARACTERISTICS ●LBM2016 ■Q-vs-Frequency characteristics 100 100J 101J Q 10 1R0J ■Impedance-vs-Frequency characteristics 1000000 101J 100000 10000 100J 1R0J ■Inductance-vs-Frequency characteristics 1000 Inductance[μH] 100 101J 10 100J 1000 100 0 1 10 1 1 1R0J 10 Frequency[MHz] 100 10 Freaquency[MHz] 100 0 1 10 Freaquency[MHz] 100 ●LEM2520 ■Q-vs-Frequency characteristics Measured by HP4285A＋42851A ■DC Bias characteristics Measured by HP4285A＋42841A ■Temperature characteristics Measured by HP4285A＋42851A ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 56 1 wound03_e-01 ■ PACKAGING ①Minimum Quantity Type LBC3225/CBC3225 LB3218 LBR2518/LBC2518/LB251 /CB2518/CBC2518/LEM2520 LBM2016/LBC2016/ LB2016/CB2016/CBC2016 LB2012/LBC2012/LBR202 /CB2012/CBC2012 CBL2012 LB1608 LBMF1608/CBMF1608 Standard Quantity pcs］［ Papar Tape Embossed Tape ー 1000 ー 2000 ーーー 4000 4000 ー 2000 2000 3000 ーー 3000 ④Leader and Blank Portion ⑤Reel Size φ60 ＋1 φ2.36 ＋0.039 ) （ −0 −0 10.0±1.5 (0.394±0.059) ◦Embossed tape ⑥Top Tape Strength The top tape requires a peel-off force 0.1 to 0.7N in the direction of the arrow as illustrated below. Pull direction ③Taping Dimensions ◦Embossed Tape 0.315 inches wide）（ ◦Card board carrier tape 0.315 inches wide）（ Type LBM 2016 LEM 2520 LBC3225/ CBC3225 LB3218 Chip cavity A B Insertion pitch F Tape thickness T K 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. 1.75±0.1 （0.069±0.004） 0.083±0.004） 0.157±0.004） 0.012±0.002）（0.074）（（（ 2.3±0.1 2.7±0.1 4.0±0.1 0.3±0.05 2.1±0.1 （0.091±0.004）（0.106±0.004） 0.157±0.004） 0.012±0.002） 0.083±0.004）（（（ 2.8±0.1 3.5±0.1 4.0±0.1 0.3±0.05 4.0max. （0.110±0.004） 0.138±0.004） 0.157±0.004） 0.012±0.002）（0.157）（（（ 2.1±0.1 3.5±0.1 4.0±0.1 0.3±0.05 2.2max. （0.084±0.004）（0.014±0.004） 0.157±0.004） 0.012±0.002）（0.086）（（ LB2518 / CB2518 2.15±0.1 2.7±0.1 4.0±0.1 0.3±0.05 2.2max. LBC2518 / CBC2518 （0.085±0.004）（0.107±0.004） 0.157±0.004） 0.012±0.002）（0.086）（（ LBR2518 LB2016/ CB2016 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 1.9max. LBC2016 / CBC2016 （0.069±0.004） 0.083±0.004） 0.157±0.004） 0.012±0.002）（0.074）（（（ LB2012 / CB2012 1.45±0.1 2.25±0.1 4.0±0.1 0.25±0.05 1.45max. LBC2012 / CBC2012 （0.058±0.004）（0.09±0.004）（0.157±0.004） 0.010±0.002）（0.057）（ LBR2012 1.55±0.1 2.3±0.1 4.0±0.1 1.1max. 1.1max. CBL2012 （0.044）（0.061±0.004）（0.091±0.004）（0.157±0.004）（0.044） 1.0±0.1 1.8±0.1 4.0±0.1 1.1max. 1.1max. LB1608 （0.044）（0.059±0.004）（0.072±0.004）（0.157±0.004）（0.044） LBMF1608 / 1.1±0.1 1.9±0.1 4.0±0.1 0.25±0.05 1.2max. CBMF1608 （0.04±0.004）（0.076±0.004）（0.157±0.004） 0.010±0.002）（0.047）（ Unit：mm inch）（＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli_e-01 1 φ180 ＋0 φ7.09 ＋0 ) （ −3 −0.118 ②Tape material 2.5 max （0.098） wound0103_reli-PRP1 ■ RELIABILITY DATA 1.Operating temperature Range LEM2520 LB3218 LB2518 LB2016 LBC3225 LBC2518 LBC2016 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2016 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 2.Storage LEM2520 LB3218 LBC3225 LBR2518 CB2518 CBC3225 CBL2012 CBMF1608 LBM2016 ー40～＋85℃ LB2012 LBC2012 LB1608 LBMF1608 CBC2012 （ー25～＋105℃ Including self-generated heat） LB2518 LBC2518 LBR2012 CB2016 CBC2518 LB2016 LBC2016 CB2012 CBC2016 LB2012 LBC2012 LB1608 LBMF1608 ー40～＋85℃ CBC2012 3.Rated Current LEM2520 LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 Within the speciﬁed tolerance CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LEM Series The maximum DC value having inductance decrease within 10％ and temperature increase within 20℃ by the application of DC bias. 4.Inductance LEM2520 LB3218 LB2518 LB2016 LBC2016 LBC3225 LBC2518 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2016 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LEM Series R12～101 LB2012 LBC2012 LB1608 LBMF1608 Within the speciﬁed tolerance CBC2012 LB・LBC・LBR・CB・CBC・CBL・LBMF・CBMF・LBM Series Measuring equipment：LCR Meter HP4285A＋42851A or its equivalent）（ Measuring frequency：Speciﬁed frequency Measuring equipment：LCR Mater HP4285A or its equivalent）（ 5.Q LEM2520 Within the speciﬁed tolerance LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 Within the speciﬁed tolerance 【Test Methods and Remarks】 LEM Series R12～101 Measuring equipment：LCR Meter HP4285A＋42851A or its equivalent）（ Measuring frequency：Speciﬁed frequency LBM Series Measuring equipment：LCR Mater HP4285A or its equivalent）（ 6.DC Resisitance LEM2520 LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 Within the speciﬁed tolerance CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LEM・LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Series　Measuring equipment：DC Ohmmeter HIOKI 3227 or its equivalent）（＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli-PRP2 1 wound0103_reli_e-01 ■ RELIABILITY DATA 7.Self-Resonant Frequency LEM2520 LB3218 LB2518 LB2016 LB2012 LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LEM2520 LB・LBC・LBR・CB・CBC・CBL・LBMF・CBMF Series LBM Series 8.Temperature Characteristic LEM2520 LB3218 LBC3225 LBR2518 CB2518 CBC3225 LB2518 LBC2518 LBR2012 CB2016 CBC2518 LB2016 LBC2016 CB2012 CBC2016 CBC2012 LB2012 LBC2012 LB1608 LBMF1608 LB1608 LBMF1608 Within the speciﬁed tolerance Measuring equipment：Impedance analyzer HP4291A or its equivalent）（ Measuring equipment：Impedance analyzer HP4291A or its equivalent）（ Measuring equipment：Network analyzer HP8720B or its equivalent）（ CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 Change of maximum inductance deviation in step 1-5　 Inductance change:Within±5％ Inductance change:Within±15％ LBMF1608・LB3218　Inductance change:Within±20％ LBC3225・LBC2518・LBC2016 Inductance change:Within±20％ LBC2012 Inductance change:Within±30％ Inductance change:Within±15％ Inductance change:Within±15％ CBC3225・CBC2518・CBC2016 Inductance change:Within±20％ CBC2012 Inductance change:Within±30％ Inductance change:Within±15％ Inductance change:Within±20％ Inductance change:Within±5％ 2 ー25 3 4 5 20 Step Temperture ℃）（ 1 20 20 Reference temperature）＋85 Maximum operating temperature）（（ 9.Rasistance to Flexure of Substrate LEM2520 LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 No damage. CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 Pressing jig Warp： 2mm LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Series）（ 3mm LEM2520）（ LB LBMF ・・ CBMF1608 Test substrate: Printed board ：0.8mm Others：1.0mm According to JIS C0051 Board 10.Body Strength LEM2520 LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LB・LBC・LBR・CB・CBC・CBL・LBM・LEM2520 Applied force：10N Duration：10sec. LB1608・LBMF1608・CBMF1608 Applied force：5N Duration：10sec. No damage. 11.Self Resonant Freguency LEM2520 LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 Inductance change : Within－10％ LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 Inductance change : Within－20％ CB2518 CB2016 CB2012 CBC2012 CBC2518 CBC2016 CBC3225 Inductance change : Within－30％ CBL2012 CBMF1608 LBM2016 Inductance change : Within－10％【Test Methods and Remarks】 Measure inductance with application of rated current using LCR metre to compare it with the initial value. ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli_e-01 1 wound0103_reli-PRP3 ■ RELIABILITY DATA 12.Adhesion of terminal electrode LEM2520 LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC3225 LBC2518 LBC2016 LBC2012 LBR2518 LBR2012 No abnormality. CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF・LEM2520　Applied force：10N to X and Y directions Duration：5 sec. Test substrate：Printed board LB1608・CBMF1608・LBMF1608 Applied force：5N to X and Y directions Duration：5 sec. Test substrate：Printed board 13.Resistance to vibration LEM2520 Inductance change:Within±5％ LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC2518 LBC2016 LBC2012 LBC3225 LBR2518 LBR2012 Inductance change:Within±10％ CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 Inductance change:Within±5％【Test Methods and Remarks】 LEM・LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF：According to JIS C5102 clause 8.2. Vibration type：A Directions：2 hrs each in X, Y and Z directions. Total：6 hrs Frequency range：10 to 55 to 10 Hz 1min.）（ Amplitude：1.5mm Mounting method：Soldering onto printed board Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEM：Recovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 14.Drop test LEM2520 Inductance change:Within±5％ LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LEM： Acceleration：980m/sec2 Duration：6msec Number of times：6 sides × 3 times Mounting method：Soldering onto printed board Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEM：Recovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 15.Solderability LEM2520 LB3218 LB2518 LB2016 LBC3225 LBC2518 LBC2016 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2016 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LEM： No signiﬁcant abnormality in appearance. No signiﬁcant abnormality in appearance. No signiﬁcant abnormality in appearance. No signiﬁcant abnormality in appearance. LB2012 LBC2012 LB1608 LBMF1608 At least 90％ of surface of terminal electrode is covered by new CBC2012 Solder temperature：230±5℃ Duration：5±0.5sec. Flux：Methanol solution with 25％ of colophony LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Solder temperature：245±5℃ Duration：5±0.5sec Flux：Methanol solution with 25％ of colophony ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli-PRP4 1 wound0103_reli_e-01 ■ RELIABILITY DATA 16.Resisitance to soldering heat LEM2520 LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 No signiﬁcant abnormality in appearance. LB3218， LB2518， LB2016， LB2012， LB1608 Inductance change:Within±10％ No signiﬁcant abnormality in appearance. LBMF1608 Inductance change:Within±20％ No signiﬁcant abnormality in appearance. LBC3225 LBC2518 LBC2016 LBC2012 LBR2518 LBR2012 CB2518 CB2016 CB2012 Inductance change:Within±10％ CBC3225 CBC2518 CBC2016 CBC2012 CBL2012 CBMF1608 Inductance change:Within±20％ LBM2016 Inductance change:Within±5％【Test Methods and Remarks】 LEM： Reﬂow condition 3 times of reﬂow over at 220±5℃ for 40sec. MAX, With Peak temperature at 240±5℃ for 5 sec. MAX. Refer to a Proﬁle of chart below.）（ Flow condition Solder temperature：260±5℃ Duration：10±1sec. Once LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： 3 times of reﬂow oven at 230℃ MIN for 40sec. with peak temperature at 260 ℃ for 5sec. 17.Resisitance to solvent LEM2520 LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 Solvent temperature：Room temperature Type of solvent：Isopropyl alcohol 　 LEM2520・LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF）（ Cleaning conditions：90s. Immersion and cleaning. 　 LEM2520・LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF）（ 18.Thermal shock Inductance change :Within±10％ Q→ R12～4R7：30 min. 5R6～330：25 min. 390～820：20 min. 101：15 min. No signiﬁcant abnormality in appearance. No signiﬁcant abnormality in appearance. No signiﬁcant abnormality in appearance. No signiﬁcant abnormality in appearance LEM2520 LB3218 LB2012 LB2518 LB2016 LB1608 LBMF1608 LBC2518 LBC2016 LBC2012 LBC3225 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 Step Temperature ℃） Duration min）（（ LEM : Conditions for 1cycle 1 ー40 30 2 ＋85 30 Inductance change:Within±10％ No signiﬁcant abnormality in appearance. Number of cycle：100 cycle Recovery：At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF：ー40～＋85℃, maintain times 30min. ,100 cycle Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 19.Damp heat Inductance change :Within±10％ Q→ R12～4R7：30 min. 5R6～330：25 min. 390～820：20 min. 101：15 min. LEM2520 LB3218 LB2012 LB2518 LB2016 LB1608 LBMF1608 LBC2518 LBC2016 LBC2012 LBC3225 LBR2518 LBR2012 CB2518 CB2016 CB2012 Inductance change:Within±10％ CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 Temperature：60±2℃ Humidity：90～95％RH Duration：1000 hrs Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEM：Recovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. No signiﬁcant abnormality in appearance. ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli_e-01 1 wound0103_reli-PRP5 ■ RELIABILITY DATA 20.Loading under damp heat Inductance change :Within±10％ Q→ R12～4R7：30 min. 5R6～330：25 min. 390～820：20 min. 101：15 min. LEM2520 LB3218 LB2012 LB2518 LB2016 LB1608 LBMF1608 LBC2518 LBC2016 LBC2012 LBC3225 LBR2518 LBR2012 CB2518 CB2016 CB2012 Inductance change:Within±10％ No signiﬁcant abnormality in appearance. CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LEM・LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF：Temperature：60±2℃ Humidity：90～95％RH Duration：1000 hrs Applied current：Rated current Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEM：Recovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 21.High temperature life test Inductance change :Within±10％ Q→ R12～4R7：30 min. 5R6～330：25 min. 390～820：20 min. 101：15 min. LEM2520 LB3218 LB2012 LB2518 LB2016 LB1608 LBMF1608 LBC2016 LBC2012 LBC3225 LBC2518 LBR2518 LBR2012 CB2518 CB2016 CB2012 CBC2518 CBC2016 CBC2012 CBC3225 CBL2012 No signiﬁcant abnormality in appearance. Inductance change:Within±10％ CBMF1608 LBM2016 【Test Methods and Remarks】 LEM・CB・CBC・CBL・LBM・CBMF：Temperature：85±2℃ Duration：1000 hrs Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEM：Recovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 22.Loading at high temperature LEM2520 LB3218 LB2518 LB2016 LB2012 LB1608 LBMF1608 LBC2518 LBC2016 LBC2012 LBC3225 Inductance change:Within±10％ No signiﬁcant abnormality in appearance. LBR2518 LBR2012 CB2016 CB2012 CB2518 CBC2518 CBC2016 CBC2012 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LB・LBC・LBR・LBMF：Temperature：85±2℃ Duration：1000 hrs Applied current：Rated current Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli-PRP6 1 wound0103_reli_e-01 ■ RELIABILITY DATA 23.Low temperature life test Inductance change :Within±10％ Q→ R12～4R7：30 min. 5R6～330：25 min. 390～820：20 min. 101：15 min. LEM2520 LB3218 LB2012 LB2518 LB2016 LB1608 LBMF1608 LBC2518 LBC2016 LBC2012 LBC3225 LBR2518 LBR2012 CB2518 CB2016 CB2012 Inductance change:Within±10％ CBC2016 CBC2012 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 【Test Methods and Remarks】 LEM・LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Temperature：－40±2℃ Duration：1000 hrs Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEM：Recovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 24.Standard condition LEM2520 LB3218 LB2518 LBC3225 LBC2518 LBR2518 LBR2012 CB2518 CB2016 CBC2518 CBC3225 CBL2012 CBMF1608 LBM2016 No signiﬁcant abnormality in appearance. LB2016 LBC2016 CB2012 CBC2016 LB2012 LBC2012 LB1608 LBMF1608 CBC2012 Standard test conditions Unless speciﬁed, Ambient temperature is 20±15℃ and the Relative humidity is 65± 20％. If there is any doubt about the test results, further measurement shall be had within the following limits: Ambient Temperature: 20±2℃ Relative humidity: 65±5％ Inductance value is based on our standard measurement systems. ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli_e-01 1 wound0103_reli-PRP7 ■ PRECAUTIONS LEM Type，LB Type，CB Type 1． Circuit Design ◆Operating environment 1．The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high Precautions reliability (trafﬁc systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2． PCB Design ◆Land pattern design Precautions 1． Please contact any of our ofﬁces for a land pattern, and refer to a recommended land pattern of a right ﬁgure or speciﬁcations. PRECAUTIONS Unit : mm 【Recommended Land Patterns】 TYPE A B C Surface Mounting ・Mounting and soldering conditions should be checked beforehand. 1608 0.55 0.7 1.0 ・Applicable soldering process to those products is reﬂow soldering only. MF1608 0.55 0.8 0.9 ・Recommended Land Patterns Technical 2012 0.7 0.8 1.45 consider2016 0.7 0.8 1.8 ations 2518 0.8 1.2 2.0 C LEM2520 0.9 1.5 1.5 3218 1.0 1.6 2.0 3225 1.0 1.6 2.7 A B A 3． Considerations for automatic placement ◆Adjustment of mounting machine Precautions 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Technical consider- 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. ations 4． Soldering ◆Wave soldering LEM Type only）（ 1． For wave soldering,please apply conditions meeting the range of the specifed conditions in our catalog or the relevant speciﬁcations. ◆Reﬂow soldering LB and CB Types）（ 1． For reﬂow soldering with either leaded or lead-free solder,the proﬁle speciﬁed in "point for controlling" is recommended. （ Precautions ◆Reﬂow soldering LEM） 1． For reﬂow soldering, please apply conditions meeting the range of the speciﬁed conditions in our catalog or the relevant speciﬁcations. ◆Recommended conditions for using a soldering iron 1． Put the soldering iron on the land-pattern. Soldering iron's temperature-Below 350℃ Duration-3 secons or less. The soldering iron shoud not come in contact with inductor directly. ◆Wave soldering LEM Type only）（ 1． Components can be damaged by excessive heat where soldering conditions exceed the speciﬁed range. ◆Reﬂow soldering LB and CB Types）（ 1． Reﬂow proﬁle 300 250 （LB CB Type）・ Peak Temp: 260＋0/ー5℃ 5 sec Max 180℃ Pre-heat zone 230℃ Minn Technical considerations 200 150 150℃ 100 50 0 90±30 sec 30±10 sec ◆Recommended conditions for using a soldering iron 1． Components can be damaged by excessive heat where soldering conditions exceed the speciﬁed range. 5． Cleaning Precautions Technical considerations 6． Handling ◆Handling 1． Keep the inductors away from all magnets and magnetic objects. ◆Breakaway PC boards splitting along perforations）（ 1． When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deﬂection or twisting to the board. Precautions 2． Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1． Please do not give the inductors any excessive mechanical shocks. ◆Handling 1． There is a case that a characteristic varies with magnetic inﬂuence. Technical ◆Breakaway PC boards splitting along perforations）（ consider1． Planning pattern conﬁgurations and the position of products should be carefully performed to minimize stress. ations ◆Mechanical considerations 1． There is a case to be damaged by a mechanical shock. 7． Storage conditions ◆Storage 1． maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. To 　・Recommended conditions 　　Ambient temperature：0～40℃　／　Humidity：Below 70% RH Precautions The ambient temperature must be kept below 30℃ Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, LE type inductors should be used within one year from the time of delivery. LB type：Should be used within 6 months from the time of delivery. LE type：In case of storage over 6 months, solderability shall be checked before actual usage. Technical ◆Storage 1． Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of considerations taping/packaging materials may take place. ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. ◆Cleaning conditions 1． LEM Type, LB Type, CB Type Washing by supersonic waves shall be avoided. ◆Cleaning conditions 1． LEM Type, LB Type, CB Type If washing by supersonic waves, supersonic waves may cause broken products. wound0103_reli-PRP8 1 wound0103_reli_e-01 SMD INDUCTORS LOW PROFILE TYPE REFLOW ■ FEATURES ◦Small and Low proﬁle inductor. ◦It corresponds to High current. ◦Simple and original magnetic shield structure. ◦Durable structure against dropping impact. ■ APPLICATIONS ◦For small DC/DC converter (cellular Phone, HDD, DVC, DSC, PDA, LCD display etc). ■ ORDERING CODE N R△4 ❶ ❶Type Coating resin speciﬁcation △＝Blank Space 0 ❷ 1 8 T△ T△1 ❸ ❸Packaging Tape & Reel △＝Blank Space 0 ❹ 0 M△ ❺ ❻ △ ❻Internal code Standard product △＝Blank Space NR△, NRG ❹Nominal inductance 〔μH〕 example ❺Inductance tolerance M ±20% N ±30% example 3010 3012 3015 4010 4012 4018 ❷External dimensions (W×L×H) 4026 4.0×4.0×2.6mm 3.0×3.0×1.0mm 5040 5.0×5.0×4.0mm 3.0×3.0×1.2mm 6012 6.0×6.0×1.2mm 3.0×3.0×1.5mm 6020 6.0×6.0×2.0mm 4.0×4.0×1.0mm 6028 6.0×6.0×2.8mm 4.0×4.0×1.2mm 6045 6.0×6.0×4.5mm 4.0×4.0×1.8mm 8040 8.0×8.0×4.0mm 2R2 100 101 2.2 10 100 ※R＝decimal point ■ E XTERNAL DIMENSIONS/STANDARD QUANTITY L H e W f e L H e ℓ W e Type NR3010 NR3012 NR3015 NR4010 NR4012 NR4018 NRG4026 L W H 1.0 max （0.039 max） e f Standard Quantity [pcs] Tape & Reel 2000 2000 2000 5000 4500 3500 2000 Δe f Type L W H e Δe f Δℓ Standard Quantity [pcs] Tape & Reel 1500 1.2 max 0.9±0.2 3.0±0.1 3.0±0.1 1.9±0.2 （0.118±0.004）（0.118±0.004）（0.047 max）（0.035±0.008）（0.075±0.008） 1.5 max （0.059 max） 1.0 max （0.039 max） 4.0±0.2 （0.157± 0.008） 4.0±0.2 （0.157± 0.008） 1.2 max （0.047 max） 1.1±0.2 2.5±0.2 1.8 max （0.043±0.008）（0.098±0.008）（0.071 max） NR5040 ＊3） 4.1max （ 4.9±0.2 4.9±0.2 　 0.161max） 1.2±0.2 0.3±0.2 3.3±0.2 1.3±0.3 （0.193±0.008）（0.193±0.008）＊4）4.0max （0.047±0.008）（0.011±0.008）（0.130±0.008）（0.051±0.011）　 0.157max）（ 6.0±0.2 6.0±0.2 1.2 max 1.35±0.2 0.3±0.2 4.0±0.2 NR6012 （E Type）（0.236±0.008）（0.236±0.008）（0.047 max）（0.053±0.008）（0.011±0.008）（0.157±0.008） NR6020 NR6028 NR6045 1.35±0.2 0.3±0.2 4.0±0.2 6.0±0.2 6.0±0.2 2.0 max （0.236±0.008）（0.236±0.008）（0.078 max）（0.053±0.008）（0.011±0.008）（0.157±0.008） 1.35±0.2 0.3±0.2 4.0±0.2 6.0±0.2 6.0±0.2 2.8 max （0.236±0.008）（0.236±0.008）（0.110 max）（0.053±0.008）（0.011±0.008）（0.157±0.008） 1.35±0.2 0.3±0.2 4.0±0.2 6.0±0.2 6.0±0.2 4.5 max （0.236±0.008）（0.236±0.008）（0.177 max）（0.053±0.008）（0.011±0.008）（0.157±0.008） 2.3±0.3 （0.091±0.011） 1000 2500 2000 1500 Unit : mm (inch) 2.6 max （0.102 max） *1）4.2max 8.0±0.2 8.0±0.2 （0.165max） 1.6±0.3 5.6±0.3 NR8040 （0.315±0.008） 0.315±0.008） *2）4.0max （0.063±0.012） 0.220±0.012）（（（0.157max） *1）0 R9～6R8 Type *2）100～101 Type *3）1R5～100 Type *4）150～470 Type 1000 Unit : mm (inch) ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 122 1 wound04_e-01 Recommended Land Pat terns 【NR3010, NR3012, NR3015】 2.2 2.7 3.7 0.8 0.8 4.0 5.7 【NR4010, NR4012, NR4018, NRG4026】 2.8 【NR5040】 3.6 【NR6012,NR6020,NR6028,NR6045】 4.7 【NR8040】 5.6 7.5 1.2 1.2 1.5 1.5 1.6 1.6 1.8 1.8 Unit : mm ■ AVAILABLE INDUCTANCE RANGE Range Type NR 3010 IMAX [mA] NR 3012 NR 3015 NR 4010 NR 4012 NR 4018 NR 5040 NR 6 012 NR 6 020 NR 6 028 NR 6 045 NR 8040 NRG 4026 Rdc±30％［Ω］ Rdc±20％ IMAX ［Ω］ [mA] 0.065 1490 Rdc±20％ IMAX ［Ω］ [mA] 0.05 2100 Rdc±20％ IMAX ［Ω］ [mA] 0.030 1050 Rdc±20％ IMAX ［Ω］ [mA] 0.100 1500 Rdc±20％ IMAX ［Ω］ [mA] 0.060 1830 Rdc±20％ IMAX ［Ω］ [mA] 0.030 Rdc±30％ IMAX ［Ω］ [mA] Inductance μH］［ 0.8 1300 1.0 3.3 10 47 100 220 500 220 Rdc±20％ IMAX ［Ω］ [mA] 3800 Rdc±20％ IMAX ［Ω］ [mA] 0.020 4600 Rdc±30％ IMAX ［Ω］ [mA] 0.013 4200 Rdc±30％ IMAX ［Ω］ [mA] 0.014 7800 Rdc±30％ IMAX ［Ω］ [mA] 0.006 2300 FERRITE PRODUCTS 3600 0.450 540 2.05 250 0.290 700 1.45 300 0.230 560 1.34 240 0.380 740 1.81 350 0.240 840 1.00 0.180 2100 900 0.020 1730 0.095 0.235 1400 950 0.125 1900 0.290 620 0.600 700 0.500 1000 0.290 0.065 2500 0.047 3100 0.030 0.056 1000 0.310 320 0.034 1300 0.085 650 0.300 170 4.00 2.18 ■ PART NUMBERS ●NR 3010 Shielded type Ordering code NR NR NR NR NR NR NR NR NR NR NR 3010T 3010T 3010T 3010T 3 010T 3 010T 3 010T 3 010T 3 010T 3 010T 3 010T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 126 98 82 63 56 46 35 30 25 20 17 DC Resistance [Ω] (±20％) 0.0 65 0.080 0.095 0.140 0.190 0.300 0.450 0.740 1.03 1.55 2.05 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc2 Idc1 1,300 1,400 1,300 1,200 1,100 1,100 870 940 750 780 610 630 500 510 400 400 350 350 260 275 220 235 Measuring frequency 〔kHz〕 100 ±20％ ●NR 3012 Shielded type Ordering code NR NR NR NR NR NR NR NR NR NR NR 3012T 3012T 3012T 3012T 3012T 3 012T 3 012T 3 012T 3 012T 3 012T 3 012T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 110 92 70 55 48 40 32 27 22 19 17 DC Resistance [Ω] (±20％) 0.050 0.060 0.080 0.100 0.130 0.190 0.290 0.450 0.630 1.03 1.45 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 1,500 1,490 1,400 1,360 1,100 1, 200 910 1,050 770 980 670 740 540 630 440 485 375 420 310 330 250 280 Measuring frequency 〔kHz〕 100 ±20％ ●NR 3015 Shielded type Ordering code NR NR NR NR NR NR NR NR NR NR NR 3015T 3015T 3015T 3015T 3015T 3015T 3 015T 3 015T 3 015T 3 015T 3 015T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 100 87 64 49 40 36 28 23 20 18 17 DC Resistance [Ω] (±20％) 0.030 0.040 0.060 0.080 0.120 0.160 0.230 0.360 0.520 0.840 1.34 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 2,100 2,100 1,820 1,800 1,480 1,500 1,210 1, 230 1,020 1,040 870 880 700 710 560 560 470 470 390 370 320 300 Measuring frequency 〔kHz〕 100 ±20％ ※） saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) The ※） temperature rise current value Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃) The （ ※） rated current is the DC current value that satisﬁes both of current value saturation current value and temperature rise current value. The ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound04_e-01 1 123 ■ PART NUMBERS ●NR 4010 Shielded type Ordering code NR NR NR NR NR NR NR NR NR NR 4010T 4010T 4010T 4010T 4 010T 4 010T 4 010T 4 010T 4 010T 4 010T 1R0N 2R2N 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 2.2 3.3 4.7 6.8 10 15 22 33 47 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 116 73 58 47 38 31 24 19 15 13 DC Resistance [Ω] (±20％) 0.100 0.150 0.180 0.210 0.300 0.380 0.510 0.870 1.54 1.81 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 1,800 1,050 89 0 1,150 1,100 820 900 750 740 620 560 600 470 510 360 400 280 300 240 280 Measuring frequency 〔kHz〕 100 ±20％ ●NR 4012 Shielded type Ordering code NR NR NR NR NR NR NR NR NR NR 4012T 4012T 4012T 4012T 4012T 4 012T 4 012T 4 012T 4 012T 4 012T 1R0N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M 330M 470M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 2.2 3.3 4.7 6.8 10 15 22 33 47 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 131 66 50 45 35 28 23 18 15 12 DC Resistance [Ω] (±20％) 0.0 60 0.09 0 0.130 0.140 0.180 0.240 0.400 0.480 0.810 1.00 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 2,500 1,500 1,650 1, 200 1,200 980 1,050 96 0 900 840 740 770 560 600 510 540 400 420 350 370 Measuring frequency 〔kHz〕 ±20％ 100 ●NR 4018 Shielded type Ordering code NR 4018T 1R0N NR 4018T 2R2M NR 4018T 3R3M NR 4018T 4R7M NR 4018T 6R8M NR 4018T 100M NR 4018T 150M NR 4018T 220M NR 4018T 330M NR 4018T 470M NR 4018T 680M NR 4018T 101M NR 4018T 151M NR 4018T 221M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 80 52 44 34 29 24 19 16 12 10 8.3 6.5 5.5 4.0 DC Resistance [Ω] (±20％) 0.030 0.06 0 0.070 0.090 0.110 0.180 0.250 0.360 0.530 0.650 1.00 1.50 2.50 4.00 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 4,000 1,830 2,700 1,440 2,000 1, 230 1,700 1, 200 1,450 1,060 1,200 840 940 650 800 590 650 490 570 420 470 320 400 270 310 220 270 170 Measuring frequency 〔kHz〕 ±20％ 100 ●NR 5040 Shielded type Ordering code NR 5040T 1R5N NR 5040T 2R2N NR 5040T 3R3N NR 5040T 4R7N NR 5040T 6R8M NR 5040T 100M NR 5040T 150M NR 5040T 220M NR 5040T 330M NR 5040T 470M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 60 42 32 28 21 18 13 9 7 6 DC Resistance [Ω] (±30％) 0.020 0.022 0.027 0.029 0.049 0.056 0.080 0.126 0.180 0.310 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 6,000 3,600 4,600 3,500 3,800 3,300 3,300 3,100 2,600 2,300 2,300 2,100 2,000 1,800 1,600 1,400 1,300 1, 200 1,100 90 0 Measuring frequency 〔kHz〕 ±30％ 100 ±20％ ●NR 6012 Shielded type Ordering code NR 6012T 2R5NE NR 6012T 4R0NE NR 6012T 5R3ME NR 6012T 6R8ME NR 6012T 100ME NR 6012T 150ME NR 6 012T 220ME NR 6 012T 330ME NR 6 012T 470ME NR 6 012T 680ME NR 6 012T 101ME EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 2.5 4.0 5.3 6.8 10 15 22 33 47 68 100 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 45 39 34 30 22 18 12 8 6 3 1 DC Resistance [Ω] (±20％) 0.09 0 0.105 0.125 0.165 0.235 0.330 0.530 0.700 1.05 1.35 2.18 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 2,100 1,730 1,800 1,570 1,500 1,400 1,300 1,180 1,000 1,000 800 790 760 630 590 530 520 460 440 410 350 320 Measuring frequency 〔kHz〕 100 ±20％ ※） saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) The ※） temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃) The ※） e rated current is the DC current value that satisﬁes both of current value saturation current value and temperature rise current value. Th ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 124 1 wound04_e-01 ■ PART NUMBERS ●NR 6020 Shielded type Ordering code NR 6020T 0R8N NR 6020T 1R5N NR 6020T 2R2N NR 6020T 3R3N NR 6020T 4R7N NR 6020T 6R8N NR 6020T 100M NR 6020T 220M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 0.8 1.5 2.2 3.3 4.7 6.8 10 22 Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 110 93 73 55 43 30 18 11 DC Resistance [Ω] (±20％) 0.020 0.026 0.034 0.040 0.058 0.085 0.125 0.290 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 5,500 3,800 4,000 3, 200 3,200 2,700 2,800 2,600 2,400 2,000 2,000 1,800 1,700 1,400 1,050 950 Measuring frequency 〔kHz〕 ±30％ 100 ±20％ ●NR 6028 Shielded type Ordering code NR 6028T 0R9N NR 6028T 1R5N NR 6028T 2R2N NR 6028T 3R0N NR 6028T 4R7M NR 6028T 6R0M NR 6028T 100M NR 6028T 150M NR 6028T 220M NR 6028T 330M NR 6028T 470M NR 6 028T 680M NR 6 028T 101M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 0.9 1.5 2.2 3.0 4.7 6.0 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 90 78 68 55 39 30 20 17 12 10 8 5 3 DC Resistance [Ω] (±30％) 0.013 0.016 0.020 0.023 0.031 0.040 0.065 0.095 0.135 0.220 0.300 0.420 0.600 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 6,600 4,600 5,000 4, 200 4,200 3,700 3,600 3,400 2,700 3,000 2,500 2,500 1,900 1,900 1,600 1,800 1,300 1,400 1,100 1,100 950 920 760 770 620 660 Measuring frequency 〔kHz〕 FERRITE PRODUCTS ±30％ 100 ±20％ ●NR 6045 Shielded type Ordering code NR 6045T 1R0N NR 6045T 1R3N NR 6045T 1R8N NR 6045T 2R3N NR 6045T 3R0N NR 6045T 4R5M NR 6045T 6R3M NR 6045T 100M NR 6045T 150M NR 6045T 220M NR 6045T 330M NR 6045T 470M NR 6045T 680M NR 6045T 101M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.3 1.8 2.3 3.0 4.5 6.3 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 110 95 DC Resistance [Ω] (±30％) 0.014 0.016 0.018 0.021 0.024 0.031 0.038 0.047 0.077 0.115 0.145 0.220 0.330 0.500 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc2 Idc1 8,500 8,000 7,000 6,000 5,000 4,000 3,800 3,000 2,300 1,900 1,500 1,300 1,000 800 4, 200 4,000 3,700 3,500 3, 200 3,000 2,800 2,500 1,900 1,500 1,400 1,100 90 0 700 Measuring frequency 〔kHz〕 ±30％ 80 60 45 25 15 12 10 100 ±20％ 7 6 5 4 3 ●NR 8040 Shielded type Ordering code NR NR NR NR NR NR NR NR NR NR NR NR NR 8040T 8040T 8040T 8040T 8040T 8040T 8040T 8040T 8040T 8040T 8040T 8040T 8040T 0R9N 1R4N 2R0N 3R6N 4R7N 6R8N 100M 150M 220M 330M 470M 680M 101M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 0.9 1.4 2.0 3.6 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 85 63 50 34 30 24 22 16 13 12 8 7 6 DC Resistance [Ω] (±30％) 0.00 6 0.007 0.009 0.015 0.018 0.025 0.034 0.050 0.066 0.100 0.150 0.230 0.290 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 11,000 7,800 9,000 7,000 6,300 7,400 4,900 5,300 4,100 4,700 3,700 4,000 3,400 3,100 2,400 2,700 2,200 2, 200 1,700 1,900 1,400 1,500 1,100 1,200 1,000 1,000 Measuring frequency 〔kHz〕 ±30％ 100 ±20％＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound04_e-01 1 125 ■ PART NUMBERS ●NRG 4026 Shielded type Ordering code NRG4026 T 1R2N NRG4026 T 2R3N NRG4026 T 3R5M NRG4026 T 4R7M NRG4026 T 6R6M NRG4026 T 100M NRG4026 T 150M NRG4026 T 220M NRG4026 T 330M NRG4026 T 470M Inductance [μH] 1.2 2.3 3.5 4.7 6.6 10 15 22 33 47 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 120 96 58 46 33 DC Resistance [Ω] (±30%) 0.030 0.040 0.050 0.055 0.0 65 0.085 0.110 0.165 0.200 0.300 〔 Rated current ※） mA〕 Saturation current Temperature rise current Idc1 Idc2 3,100 2,100 1,800 1,450 1,300 1,000 900 610 540 410 2,300 1,970 1,700 1,600 1,500 1,300 1,10 0 900 800 650 Measuring frequency 〔kHz〕 ±20％ 26 19 13 9 6 100 ※） he saturation current (Idc1) is DC current value Inductance decrease down to 30%. (at 20℃) T ※） temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃) The ※） e rated current is Idc2. Th ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 126 1 wound04_e-01 ■ ELECTRICAL CHARACTERISTICS ■ DC Bias characteristics NR 3010 100 100 NR 3012 100 （Measured by HP4285A） NR 3015 100 NR 4010 470M 470M 470M 470M Inductance μH〕〔 Inductance μH〕〔 Inductance μH〕〔 Inductance μH〕〔 220M 220M 220M 220M 10 100M 10 100M 10 100M 10 100M 4R7M 4R7M 4R7M 4R7M 2R2M 2R2M 2R2M 2R2N FERRITE PRODUCTS 1 10 100 1,000 10,000 1 10 100 1,000 10,000 1 10 100 1,000 10,000 1 10 100 1,000 10,000 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 NR 4012 100 1000 NR 4018 100 NR 5040 NR 6012 E Type）（ 1000 470M 221M 470M 100 Inductance μH〕〔 Inductance μH〕〔 220M Inductance μH〕〔 Inductance μH〕〔 101M 220M 100 101M 10 100M 470M 10 100M 470M 220M 220M 10 4R7M 100M 4R7M N 10 100M 5R3M 4R7N 2R2N 2R2M 2R2M 1 10 100 1,000 10,000 1 10 100 1,000 10,000 1 10 100 1,000 10,000 1 10 100 1,000 10,000 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 100 NR 6020 1000 NR 6028 NR 6045 1000 1000 NR 8040 220M 100 100 101M 10 101M 100 101M 470M 220M Inductance μH〕〔 Inductance μH〕〔 Inductance μH〕〔 220M 220M 4R7M 2R2M 10 100M 4R7 2R2 0R9 10 100M 4R5N 2R3N Inductance μH〕〔 100M 470M 470M 10 100M 4R7N 2R0N 1 0R8N 1 1 1R0N 1 0R9N 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 0.1 10 100 1,000 DC Bias mA〕〔 10,000 100,000 0.1 10 100 1,000 DC Bias mA〕〔 10,000 100,000 DC Bias mA〕〔 DC Bias mA〕〔 100 NRG 4026 470M Inductance μH〕〔 220M 10 100M 4R7M 2R3N 1 10 100 1,000 10,000 DC Bias mA〕〔＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound04_e-01 1 127 SMD INDUCTORS SMALL AND LARGE CURRENT TYPE REFLOW ■ FEATURES ◦Small and Low proﬁle inductor. ◦It corresponds to High current. ◦Simple and original magnetic shield structure. ◦Durable structure against dropping impact. ■ APPLICATIONS ◦For small DC/DC converter (cellular Phone, HDD, DVC, DSC, PDA, LCD display etc). ■ ORDERING CODE N R ❶ H 2 4 ❷ 1 0 T△ T△1 ❸ ❸Packaging Tape & Reel △＝Blank Space example 0 ❹ 0 M○○○ ❺ ❺Inductance tolerance M ±20% N ±30% ❻ ❻Internal code ○○○ Standard products ○＝Blank Space ❶Type NRH NRS Coating resin speciﬁcation NRV ❷External dimensions （W×L×H） example ❹Nominal inductance 〔μH〕 2R2 100 101 2.2 10 100 2410 3010 3012 5012 5014 5020 6010 2.4×2.4×1.0mm 3.0×3.0×1.0mm 3.0×3.0×1.2mm 5.0×5.0×1.2mm 5.0×5.0×1.4mm 5.0×5.0×2.0mm 6.0×6.0×1.0mm ※R＝decimal point ■ E XTERNAL DIMENSIONS/STANDARD QUANTITY L H e W f e W e L H e f Δ ℓ Δe Δe Standard Quantity [pcs] Tape & Reel 1000 1000 800 1000 Type NRH2410 L W H e f Standard Quantity [pcs] Tape & Reel 2500 2000 2000 Type NRS5012 NRS5014 NRS5020 NRS6010 L W H e Δe f Δℓ 2.4±0.1 2.4±0.1 1.0 max 0.6±0.2 1.45±0.2 （0.095±0.004）（0.095±0.004）（0.039 max）（0.024±0.008）（0.057±0.008） 1.0 max NRH3010 3.0±0.1 （0.039 max） 0.9±0.2 1.9±0.2 3.0±0.1 NRH3012 （0.118±0.004）（0.118±0.004） 1.2 max （0.035±0.008）（0.075±0.008） NRV3012 （0.047 max） Recommended Land Patterns Unit：mm inch）（ 1.2 max （0.047 max） 4.9±0.2 4.9±0.2 1.4 max 1.2±0.2 0.3±0.2 3.3±0.2 1.3±0.3 （0.193±0.008）（0.193±0.008）（0.055 max）（0.047±0.008）（0.011±0.008）（0.130±0.008）（0.051±0.011） 2.0 max （0.079 max） 0.3±0.2 4.0±0.2 2.3±0.3 6.0±0.2 6.0±0.2 1.0 max 1.35±0.2 （0.236±0.008）（0.236±0.008）（0.039 max）（0.053±0.008）（0.011±0.008）（0.157±0.008）（0.091±0.011）【NRS6010】 4.7 Unit：mm inch）（【NRS5012, NRS5014, NRS5020】 3.6 2.7 4.0 5.7 【NRH2410】 1.45 2.0 0.7 0.7 【NR3010, NRH3012, NRV3012】 2.2 0.8 0.8 1.5 1.5 1.6 1.6 ■ AVAILABLE INDUCTANCE RANGE Range Type Imax [mA] NRH2410 Rdc±20％ Imax ［Ω］[mA] NRH3010 Rdc±20％ Imax ［Ω］[mA] NRH3012 Rdc±20％ Imax ［Ω］[mA] NRV3012 Rdc±20％ Imax ［Ω］[mA] 2300 NRS5012 Rdc±20％ Imax ［Ω］[mA] 0.053 NRS5014 Rdc±20％ Imax ［Ω］[mA] NRS5020 Rdc±20％ Imax ［Ω］[mA] NRS6010 Rdc±20％［Ω］ Inductance μH］［ 1.0 1410 2.2 4.7 10 22 100 450 300 0.070 1480 0.065 1710 0.048 1100 0.120 3600 2800 0.045 0.100 1300 900 0.021 1900 0.120 1000 0.260 0.090 0.270 0.690 600 1.47 380 0.350 720 0.770 500 0.270 0.630 850 0.420 1800 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 128 1 wound05_e-01 ■ PART NUMBERS ●NRH 2410 Shielded type Ordering code NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NR H2410T NR H2410T NR H2410T NR H2410T R68NN 4 1R0NN 4 1R5MN 2R2MN 3R3MN 4R7MN 6R8MN 100MN 150MN 220MN EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 120 106 94 77 56 50 43 32 27 22 DC Resistance [Ω] (±20%) 0.0 60 0.070 0.110 0.150 0.220 0.290 0.410 0.690 1.02 1.47 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 2,200 1,570 1,800 1,410 1,550 1,160 1,290 970 770 1,000 670 880 570 750 450 550 370 470 300 390 Measuring frequency 〔kHz〕 100 ±20％ ●NRH 3010 Type FERRITE PRODUCTS Ordering code NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NR H3010T NR H3010T NR H3010T NR H3010T 1R2N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.2 1.5 2.2 3.3 4.7 6.8 10 15 22 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 120 99 86 64 50 44 34 25 22 DC Resistance [Ω] (±20%) 0.0 65 0.075 0.083 0.130 0.170 0.250 0.350 0.550 0.770 ±20％〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 1,700 1,480 1,370 1,440 1,300 1,300 1,000 1,030 900 850 745 700 6 00 620 480 450 410 380 Measuring frequency 〔kHz〕 100 ●NRH 3012 Type Ordering code NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NR H3012T NR H3012T NR H3012T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 111 95 78 61 50 43 32 26 22 DC Resistance [Ω] (±20％) 0.048 0.055 0.075 0.100 0.130 0.190 0.270 0.450 0.630 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 2,200 1,710 1,600 1,700 1,500 1,370 1,200 1, 210 1,060 1,000 890 850 730 720 570 530 500 500 Measuring frequency 〔kHz〕 100 ±20％ ●NRV 3012 Type EHS (Environmental Hazardous Substances) RoHS Inductance [μH] 2.2 Inductance Tolerance ±20％ Self-resonant frequency 〔MHz〕 min.) ( 70 DC Resistance [Ω] (±20％) 0.120 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 1,800 1,100 Measuring frequency 〔kHz〕 100 Ordering code NRV3012T 2R2M ●NRS 5012 Type Ordering code NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 100 86 70 48 40 36 26 DC Resistance [Ω] (±20％) 0.053 0.070 0.085 0.160 0.180 0.260 0.420 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 4,500 2,300 2, 200 3,800 3,100 2,000 1,450 2,400 1,400 2,200 1,100 1,700 850 1,400 Measuring frequency 〔kHz〕 100 ±20％ ●NRS 5014 Type EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS Inductance [μH] 1.2 2.2 3.3 4.7 Ordering code NRS5014T 1R2N NRS5014T 2R2N NRS5014T 3R3N NRS5014T 4R7N Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 86 56 48 41 DC Resistance [Ω] (±20％) 0.045 0.065 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 3,800 2,800 2,350 2,050 2,800 2,300 2,100 1,800 Measuring frequency 〔kHz〕 ±30％ 0.080 0.100 100 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound05_e-01 1 129 ■ PART NUMBERS ●NRS 5020 Type Ordering code NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T 1R0N 1R5N 2R2N 3R3N 4R7M 6R8M 100M 150M 220M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 81 68 57 46 37 30 24 20 17 DC Resistance [Ω] (±20％) 0.021 0.026 0.035 0.048 0.06 0 0.090 0.120 0.165 0.260 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 4,000 3,600 3, 200 3,350 2,900 2,900 2,400 2,400 2,000 2,000 1,650 1,600 1,300 1,450 1,100 1, 200 1,00 0 9 00 Measuring frequency 〔kHz〕 ±30％ 100 ±20％ ●NRS 6010 Type Ordering code NRS6010T NRS6010T NRS6010T NRS6010T NRS6010T NRS6010T 1R5N 2R2N 3R3N 4R7N 6R8N 100M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.5 2.2 3.3 4.7 6.8 10 Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 90 65 50 38 30 25 DC Resistance [Ω] (±20％) 0.090 0.110 0.135 0.165 0.220 0.270 ±30％ ±20％〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 2,400 1,900 1,900 1,700 1,600 1,500 1,300 1,400 1,200 1, 200 1,000 1,100 Measuring frequency 〔kHz〕 100 ※） saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) The ※） temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃) The ※） e rated current is the DC current value that satisﬁes both of current value saturation current value and temperature rise current value. Th ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 130 1 wound05_e-01 ■ ELECTRICAL CHARACTERISTICS ■ DC Bias characteristics NRH 2410 100 100 （Measured by HP4285A） NRH 3010 100 NRH 3012 100 NRV 3012 220M 220M 220M 10 100M 10 10 10 100M 4R7M Inductance μH〕〔 Inductance μH〕〔 Inductance μH〕〔 4R7M 4R7M 2R2M 2R2M 2R2M Inductance μH〕〔 100M 2R2M 1 1R0N 1 1 1R0N 1 FERRITE PRODUCTS 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 NRS 5012 100 100 NRS 5014 100 NRS 5020 100 NRS 6010 200M 10 Inductance μH〕〔 Inductance μH〕〔 Inductance μH〕〔 4R7M 4R7M 4R7M Inductance μH〕〔 100M 10 10 100M 10 100M 4R7M 2R2M 2R2N 2R2N 1 1R0N 1 1R2N 1 1R0N 1 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound05_e-01 1 131 ■ PACKAGING ①Minimum Quantity Type NRH 2410 NR 3010/NRH 3010 NR 3012/NRH3012/NRV3012 NR 3015 NR 4010 NR 4012 NR 4018 NRG4026 NRS5012 NRS5014 NRS5020 NR 5040 NRS6010 NR 6012 NR 6020 NR 6028 NR 6045 NR 8040 Standard Quantity [pcs] Tape ＆ Reel 2500 2000 2000 2000 5000 4500 3500 2000 1000 1000 800 1500 1000 1000 2500 2000 1500 1000 Type NR 4010 NR 4012 NR 4018 NRG 4026 NRS 5012 NRS 5014 NRS 5020 5.25±0.1 5.25±0.1 （0.207±0.004） 0.207±0.004）（ 4.3±0.1 4.3±0.1 （0.169±0.004） 0.169±0.004）（ Chip cavity A B Insertion pitch F Tape thickness T K 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 2.1±0.1 （0.083±0.004） 0.3±0.05 3.1±0.1 （0.012±0.002） 0.122±0.004）（ 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 2.3±0.1 （0.091±0.004） 4.2±0.1 （0.165±0.004） 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 8.0±0.1 （0.315±0.004） 5.15±0.1 5.15±0.1 NR 5040 （0.203±0.004） 0.203±0.004）（ NRS 6010 NR 6012 NR 6020 NR 6028 NR 6045 6.3±0.1 6.3±0.1 （0.248±0.004） 0.248±0.004）（ 0.4±0.1 （0.016±0.004） 2.3±0.1 （0.090±0.004） ②Tape Material 3.1±0.1 （0.122±0.004） 4.7±0.1 （0.185±0.004） Unit : mm (inch) ◦Embossed tape 16mm wide (0.63 inches wide) 2.0±0.1 （0.079±0.004） 4.0±0.1 （0.157±0.004） φ1.5±0.1 （0.059±0.004） F CHIP cavity K 1.75±0.1 （0.069±0.004） T 16.0±0.3 （0.630±0.012） A 7.5±0.1 （0.295±0.004） B Electrode bottom view）（ ③Taping dimensions ◦Embossed tape 8mm wide (0.315 inches wide) （0.059ー0 ＋0.1 φ1.5ー0 Type NR 8040 Chip cavity A B Insertion pitch F Tape thickness T K 0.5±0.1 (0.020±0.004) 4.5±0.1 (0.177±0.004) Unit : mm (inch) CHIP cavity ）＋0.004 1.75±0.1 K （0.069±0.004） T 3.5±0.1 （0.138±0.004） 8.0±0.2 （0.315±0.008） 12.0±0.1 8.3±0.1 8.3±0.1 (0.327±0.004) (0.327±0.004) (0.472±0.004) A B ④Leader and Blank portion ◦NR, NRH, NRS, NRG, NRV Electrode bottom view）（ Blank portions Chip cavity Blank portions Leader F 2.0±0.05 4.0±0.1 （0.079±0.002）（0.157±0.004） Type NRH 2410 NR 3010 NRH 3010 Chip cavity A B 2.6±0.1 2.6±0.1 （0.102±0.004） 0.102±0.004）（ Insertion pitch F Tape thickness T K 0.25±0.05 1.3±0.1 （0.009±0.002） 0.051±0.004）（ 160mm or more (6.3 inches or more) 100mm or more (3.94 inches or more) 400mm or more (15.8 inches or more) 1.4±0.1 （0.055±0.004） 4.0±0.1 NR 3012 3.2±0.1 3.2±0.1 （0.157±0.004） 0.3±0.05 1.6±0.1 NRH 3012 （0.126±0.004） 0.126±0.004）（（0.012±0.002） 0.063±0.004）（ NRV3012 NR 3015 1.9±0.1 （0.075±0.004） Unit : mm (inch) Direction of tape feed ◦Embossed tape 12mm wide (0.47 inches wide) ＋0.1 φ1.5ー0 ＋0.004 （0.059ー0 ） CHIP cavity 1.75±0.1 K （0.069±0.004） T 5.5±0.1 （0.217±0.004） 12.0±0.3 （0.472±0.012） A B F 2.0±0.1 4.0±0.1 （0.079±0.004）（0.157±0.004） Electrode bottom view）（＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0405_pack-P1 1 wound0405_pack_e-01 ■ PACKAGING ⑤Reel size W 2±0.5 φ13±0.5 2.5 or less （0.098inches or less） Reel size (Reference values) φd Type NRH2410 NR 3010 NRH 3010 NR 3012 NRH 3012 NRV 3012 NR 3015 NRS 5012 NRS 5014 NRS 5020 NRS 6010 NR 6012 φD W 180±0.5 （7.087±0.019） 60±1.0 （2.36±0.04） 10.0±1.5 （0.394±0.059） 180±3.0 （7.087±0.118） 60±2.0 （2.36±0.08） 14.0±1.5 （0.551±0.059） Unit : mm (inch) W 2±0.5 φ13±0.5 t Type φD Reel size (Reference values) φd t (max.) NR 4010 NR 4012 NR 4018 NRG 4026 NR 5040 330±3.0 80±2.0 （12.99±0.118）（3.15±0.078） NR 6 020 NR 6 028 NR 6 045 NR 8040 18.5 （0.72） 13.5±1.0 （0.531±0.04） 22.5 （0.89） 17.5±1.0 （0.689±0.04） Unit : mm (inch) ⑥Top Tape Strength The top tape requires a peel-off force of 0.1 to 1.3N in the direction of the arrow as illustrated below. ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0405_pack_e-01 φD W φd φD φd 1 wound0405_pack-P2 SMD INDUCTORS LARGE CURRENT TYPE ■ FEATURES ◦SMD inductor. ◦It corresponds to High current. ◦Simple and original magnetic shield structure. ■ APPLICATIONS ◦Power supply circuits / DC-DC converters in a variety of applications such as PDP TV, LCD TV, HDD, PC, etc. ■ ORDERING CODE N R△1 ❶ 0 0 ❷ 5 T△ 0 T△1 ❸ ❹Nominal inductance 〔μH〕 example 0 ❹ 0 M△ ❺ ❻ △ ❻Internal code Standard product △＝Blank Space ❶Type NR△ Coating resin speciﬁcation △＝Blank Space ❷External dimensions (W×H) example ❸Packaging Tape & Reel △＝Blank Space 10050 10.0×5.0mm ❺Inductance tolerance M ±20% N ±30% 1R3 100 101 1.3 10 100 ※R＝decimal point ■ E XTERNAL DIMENSIONS/STANDARD QUANTITY Recommended Land Patterns Surface Mounting ・Mounting and soldering conditions should be checked beforehand. ・ Applicable soldering process to these products is reﬂow soldering only. ■ AVAILABLE INDUCTANCE RANGE Range Type Imax [A] NR 10050 Rdc±30％ [mΩ] L a 1.0 Inductance μH］［ 9 6.8 W b b 4.5 10 4.1 25 H 2.6 5.4 2.6 Unit : mm Type L W H 5.0 max (0.197 max) a 4.0 （0.16） b 1.75 （0.07） Standard Quantity [pcs] Tape & Reel 500 Unit : mm (inch) 100 220 1.2 0.8 209 450 10.0±0.3 9.8±0.5 NR 10050 （0.394±0.012）（0.386±0.020） ■ PART NUMBERS ●NR 10050 type Ordering code NR10050T1R3N NR10050T2R1N NR10050T2R9N NR10050T3R8N NR10050T4R9N NR10050T6R5N NR10050T100M NR10050T150M NR10050T220M NR10050T330M NR10050T470M NR10050T680M NR10050T101M NR10050T221M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.3 2.1 2.9 3.8 4.9 6.5 10 15 22 33 47 68 100 220 Inductance Tolerance Self-resonant frequency [MHz] (min.) 53 37 29 26 23 19 15 11 10 8.2 7.0 5.6 4.6 3.0 DC Resistance [Ω] (±30%) 0.00 68 0.008 0.0093 0.013 0.015 0.018 0.025 0.035 0.045 0.066 0.092 0.144 0.209 0.450 [ Rated current ※） mA] Saturation current Temperature rise current Idc1 Idc2 11000 90 00 10000 8300 8200 730 0 7300 6800 6600 6000 6000 5200 4700 4100 3600 3200 2600 2500 2500 2100 2000 1800 1700 1500 1300 1200 1000 800 Measuring frequency [kHz] ±30％ 100 ±20％ ※） saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) The ※） temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃) The ※） e maximum rated current is the DC current value that satisﬁes both of current value Saturation current value and temperature rise current value. (at 20℃) Th ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 132 1 wound06_e-01 ■ ELECTRICAL CHARACTERISTICS ■ DC Bias characteristics 1000.0 （Measured by HP4285A） NR 10050 221M 100.0 101M 680M Inductance μH〕〔 470M 330M 220M 150M 100M 6R5N 4R9N 3R8N 2R9N 2R1N 1R3N 10.0 1.0 FERRITE PRODUCTS 0.1 0.1 1.0 10.0 100.0 DC Bias A〕〔＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound06_e-01 1 133 ■ PACKAGING ①Minimum Quantity Type NR 10050 Standard Quantity [pcs] Tape & Reel 500 ⑥Top Tape Strength The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below. ②Tape Material ③Taping dimensions ◦Embossed tape 24mm wide (0.945 inches wide) 16.0±0.1 （0.63±0.004） φ1.5ー0 ＋0.004 （0.059ー0 ）＋0.1 2.0±0.1 （0.079±0.004） 4.0±0.1 （0.157±0.004） 1.75±0.1 （0.069±0.004） K T F B A 24.0 11.5±0.1 ー0.1 ＋0.012 （0.453±0.004） 0.945 ー0.004 ）（＋0.3 Type NR 10050 Chip cavity A 10.4±0.1 (0.409±0.004) B 9.9±0.1 (0.390±0.004) Insertion pitch F 16.0±0.1 (0.630±0.004) Tape thickness T K 0.5±0.05 (0.020±0.002) 5.7±0.1 (0.224±0.004) Unit : mm (inch) ④Leader and Blank portion Cover Tape Blank portions Chip cavity Blank portions Leader 100 to 200mm 20 to 30 pockets 40 to 50 pockets （3.94 to 7.87 inches） Direction of tape feed 1role of reel ⑤Reel size 25.5±1.0 （1.004±0.04） 2±0.5 （0.079±0.020） φ13±0.5 （φ0.512±0.020） t Type NR 10050 φD 330±3 (12.99±0.118) Reel size (Reference values) φd 80±2 (3.15±0.078) Unit : mm (inch) ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound06_pack_e-01 φD φd t (max.) 30.5 (1.201) 1 wound06_pack-P1 SMD INDUCTORS COMPACT TYPE REFLOW ■ FEATURES ◦BR C2518/BRFL2518 (NEW PRODUCTS) The best efﬁciency design is achieved by adopting bottom-surface electrode structure.Small and low-proﬁle Wound Chip Inductors that are suitable for module design which needs high electric current like DC/DC converters. ■ APPLICATIONS ◦For small DC/DC converter (cellular phone, HDD, DVC, DSC, PDA, LCD display etc). ■ ORDERING CODE B ❶ BR R△2 ❷ 5 ❸ 1 8 T ❹ 2 T R ❺ 2 M△△△ ❻ ❼ ❻Inductance tolerance M ±20% K ±10% ❶Type SMD Inductors ❷Characteristic Spec △ Low Rdc L Low proﬁle C High Current FL Low proﬁle ❸External Dimensions (W×L) : mm (inch) 1608 (0603) 1.6×0.8mm 2012 (0805) 2.0×1.2mm 2016 (0806) 2.0×1.6mm 2518 (1007) 2.5×1.8mm 3225 (1210) 3.2×2.5mm ❹Packaging Tape & Reel ❺Nominal Inductance 〔μH〕 example R20 1R0 2R2 4R7 0.2 1.0 2.2 4.7 ❼Internal code △△△ Standard product △＝Blank Space ※R＝decimal point ■ E XTERNAL DIMENSIONS/STANDARD QUANTITY L W Type BR C1608 L W H e Standard Quantity [pcs] Embossed Tape Paper Tape ーーーーーーー 3000 30 00 2000 2000 30 00 30 00 2000 Unit : mm (inch) H e 1.6±0.2 0.8±0.2 0.8±0.2 0.45±0.15 （0.063±0.008） 0.031±0.008） 0.031±0.008） 0.016±0.006）（（（ 1.0 max. 0.5±0.2 2.0±0.2 1. 25±0.2 （0.078±0.008） 0.049±0.008）（0.040 max.）（0.020±0.008）（ 2.0±0.2 1.6±0.2 1.6±0.2 0.5±0.2 （0.078±0.008） 0.063±0.008） 0.063±0.008） 0.020±0.008）（（（ 2.5±0.2 1.8±0.2 1.8±0.2 0.5±0.2 （0.098±0.008） 0.071±0.008）（0.071±0.008） 0.020±0.008）（（ 1.2 max. 0.5±0.2 2.5±0.2 1.8±0.2 （0.098±0.008） 0.071±0.008）（0.048 max.）（0.020±0.008）（ 2.5±0.2 1.8±0.2 1.0 max. 0.5±0.2 （0.098±0.008） 0.071±0.008）（0.040 max.）（0.020±0.008）（ 3.2±0.2 2.5±0.2 1.7 max. 0.75±0.2 （0.126±0.008） 0.098±0.008）（0.068 max.）（0.030±0.008）（ BR L2012 BR C2016 BR C2518 Recommended Land Patterns Surface Mounting ・Mounting and soldering conditions should be checked beforehand. ・ Applicable soldering process to this products is reﬂow soldering only. BR L2518 BRFL2518 BR L3225 C A B A Type 1608 2012 2016 2518 3225 A 0.55 0.65 0.70 0.65 1.00 B 0.80 0.90 0.80 1.50 1.60 C 0.90 1.40 1.80 1.95 2.70 Unit : mm ■ AVAILABLE INDUCTANCE RANGE Range Type Imax [mA] BR L3225 Rdc±30％ Imax [Ω] [mA] BRFL2518 Rdc±30％ Imax [Ω] [mA] BR L2518 Rdc±30％ Imax [Ω] [mA] BR C2518 Rdc±30％ Imax [Ω] [mA] BR C2016 Rdc±30％ Imax [Ω] [mA] 1,050 Inductance μH］［ BR L2012 Rdc±30％ Imax [Ω] [mA] 0.47μH 0.090 0.135 980 520 280 BR C1608 Rdc±30％ [Ω] 0.060 0.180 2.2μH 0.550 0.2μH 1.0 2.2 4.7 2,200 1μH 0.043 1,200 850 1μH 0.080 0.135 1,000 850 470 1μH 0.080 0.135 0.400 1,650 1μH 0.050 1,100 1μH 0.085 850 650 700 0.350 4.7μH 0.330 4.7μH 10 22 47 610 0.350 520 0.400 270 0.850 100 220 250 100μH 2.50 190 100μH 3.60 170 100μH 3.40 85 100μH 7.70 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 134 1 wound07_e-01 ■ PART NUMBERS ●BR C1608 type Ordering code BR BR BR BR BR BR BR BR C1608TR20M C1608TR35M C 1608TR45M C 1608TR56M C 1608TR77M C 1608T1R0M C 1608T1R5M C 1608T2R2M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 0.20 0.35 0.45 0.56 0.77 1.00 1.50 2.20 Inductance Tolerance Self-resonant DC Resistance frequency [Ω] (±30%) [MHz] (min.) 400 300 200 170 150 140 120 100 0.0 60 0.080 0.090 0.095 0.110 0.180 0.30 0 0.550 [ Rated current ※） mA] Measuring Saturation current Temperature rise current frequency [MHz] Idc1 Idc2 1,750 980 1,400 810 1,250 80 0 1,150 76 0 7.96 1,000 66 0 850 520 700 410 550 280 ±20％ ●BR L2012 t ype Ordering code BR L2012TR47M BR L2012T1R0M BR L 2012T1R5M BR L 2012T2R2M BR L 2012T3R3M BR L 2012T4R7M BR L 2012T6R8M BR L 2012T100M BR L2012T150M BR L 2012T220M BR L 2012T330M BR L 2012T470M BR L 2012T680M BR L 2012T101M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 0.47 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant DC Resistance frequency [Ω] (±30%) [MHz] (min.) 350 300 250 200 190 150 60 30 15 13 8.0 7.0 6.5 6.0 0.090 0.135 0.180 0.30 0 0.50 0 0.550 0.750 0.850 1.00 1.30 2.00 3.50 5.80 7.70 [ Rated current ※） mA] Measuring Saturation current Temperature rise current frequency [MHz] Idc1 Idc2 1,100 1,050 850 850 700 750 7.96 600 550 490 440 340 400 350 290 330 270 300 220 270 19 0 2.52 220 150 160 125 110 100 85 85 0.79 6 FERRITE PRODUCTS ±20％ ●BR C2016 t ype Ordering code BR BR BR BR BR BR BR BR BR BR BR BR BR C2016T1R0M C2016T1R5M C2016T2R2M C2016T3R3M C2016T4R7M C2016T6R8M C2016T100 □ C2016T150 □ C2016T220 □ C2016T330 □ C2016T470 □ C2016T680 □ C2016T101□ EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant DC Resistance frequency [Ω] (±30%) [MHz] (min.) 450 370 250 140 78 39 35 28 24 13 11 8 7 0.0 85 0.150 0.180 0.220 0.270 0.330 0.400 0.600 1.00 1.70 2.20 2.80 3.40 [ Rated current ※） mA] Measuring Saturation current Temperature rise current frequency [MHz] Idc1 Idc2 1,350 1,100 1,100 820 910 760 740 680 610 66 0 560 550 450 520 0.10 410 400 310 310 240 270 210 210 200 190 140 170 ±20％ ±20％ ±10％ ●BR C2518 type Ordering code BR BR BR BR BR BR BR BR BR BR BR BR BR C2518T1R0M C2518T1R5M C2518T2R2M C2518T3R3M C2518T4R7M C2518T6R8M C2518T100 □ C 2518T150 □ C 2518T220 □ C 2518T330 □ C 2518T470 □ C 2518T680 □ C 2518T101□ EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant DC Resistance frequency [MHz] (min.) [Ω] (±30%) 280 230 200 150 100 45 20 13 10 8 6.5 5.5 4.5 0.050 0.080 0.120 0.175 0.230 0.280 0.350 0.43 0.56 0.85 1.45 2.40 3.60 Rated current ※） mA] [ Saturation Temperature rise current current Idc1 Idc2 2,550 1,650 2,100 1,300 1,800 1,000 1,450 86 0 1,250 750 1,050 680 890 610 550 76 0 490 640 390 56 0 300 410 230 340 300 190 Measuring frequency [MHz] ±20％ 1.00 ±20％ ±10％・Please specify the inductance tolerance code. (M or K) ※） saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) The ※） temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃) The ※） e rated current is the DC current value that satisﬁes both of DC saturation current value and temperature rise current value. Th ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound07_e-01 1 135 ■ PART NUMBERS ●BR L2518 type Ordering code BR BR BR BR BR L2518T1R0M L2518T1R5M L2518T2R2M L 2518T3R3M L 2518T4R7M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 Inductance Tolerance Self-resonant DC Resistance frequency [MHz] (min.) [Ω] (±30%) 130 100 80 70 60 0.080 0.100 0.135 0.300 0.400 Rated current ※） mA] [ Saturation Temperature rise current current Idc1 Idc2 1,300 1,000 1,200 920 900 850 750 580 650 470 Measuring frequency [MHz] ±20％ 7.96 ●BRFL2518 type Ordering code BRFL2518T1R0M BRFL2518T1R5M BRFL2518T2R2M BR FL2518T3R3M BR FL2518T4R7M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 Inductance Tolerance Self-resonant DC Resistance frequency [MHz] (min.) [Ω] (±30%) 130 100 80 70 60 0.090 0.110 0.130 0.220 0.330 Rated current ※） mA] [ Saturation Temperature rise current current Idc1 Idc2 1,200 1, 200 1100 100 0 850 950 700 700 650 650 Measuring frequency [MHz] ±20％ 1.00 ●BR L3225 type Ordering code BR BR BR BR BR BR BR BR BR BR BR BR BR L3225T1R0M L3225T1R5M L3225T2R2M L3225T3R3M L3225T4R7M L3225T6R8M L3225T100 □ L 3225T150 □ L 3225T220 □ L 3225T330 □ L 3225T470 □ L 3225T680 □ L 3225T101□ EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance Self-resonant DC Resistance frequency [MHz] (min.) [Ω] (±30%) 220 170 150 140 120 90 70 20 13 9 7 6 5 0.043 0.045 0.065 0.120 0.180 0.270 0.350 0.570 0.690 0.840 1.00 1.40 2.50 Rated current ※） mA] [ Saturation Temperature rise current current Idc1 Idc2 2,400 2, 200 2,200 1,750 1,850 1,600 1,450 1, 200 1,300 1,000 770 1,050 900 700 530 700 470 550 420 470 420 390 330 300 270 250 Measuring frequency [MHz] ±20％ 0.10 ±20％ ±10％・Please specify the inductance tolerance code. (M or K) ※） saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) The ※） temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃) The ※） e rated current is the DC current value that satisﬁes both of DC saturation current value and temperature rise current value. Th ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 136 1 wound07_e-01 ■ ELECTRICAL CHARACTERISTICS ■ DC Bias characteristics BRL3225 10 101□ （Measured by HP4285A） BRFL2518 10 Inductance μH）（ Inductance μH）（ 4R7M BRL2518 10 4R7M BRC2518 100 101□ Inductance μH）（ Inductance μH）（ 10 100□ 2R2M 2R2M 10 100□ 1 1R0M 1 1R0M 1 1R0M 1 1R0M 0.1 1 10 100 1000 DC BIAS mA）（ 10000 0.1 1 10 100 1000 DC BIAS mA）（ 10000 0.1 1 10 100 1000 DC BIAS mA）（ 10000 0.1 1 10 100 1000 DC BIAS mA）（ 10000 BRC2016 100 101□ BRL2012 1000 Inductance μH）（ 10 BRC1608 FERRITE PRODUCTS Inductance μH）（ Inductance μH）（ 100 10 101M 2R2M 100□ 10 1 R77M 100M 1 1R0M 1 1R0M R20M 0.1 1 10 100 1000 DC BIAS mA）（ 10000 0.1 0.1 1 10 100 1000 DC BIAS mA）（ 10000 1 10 100 1000 DC BIAS mA）（ 10000 ■ Impedance-vs-Frequency characteristics BRL3225 100000 101□ （Measured by HP4291A） BRFL2518 10000 4R7M 2R2M BRL2518 10000 4R7M 2R2M BRC2518 100000 101□ 10000 Impedance Ω）（ 1000 100 10 1 1 10 100 Impedance Ω）（ Impedance Ω）（ 1R0M 1R0M Impedance Ω）（ 100□ 10000 1000 1000 100□ 1000 1R0M 100 100 1R0M 100 10 1 10 1 10 1 1000 10000 1 Frequency MHz）（ 10 100 1000 Frequency MHz）（ 10000 1 10 100 Frequency MHz）（ 1000 1 10 100 1000 10000 Frequency MHz）（ BRC2016 100000 10000 Impedance Ω）（ 1000 100 10 1 0.1 0.1 1 10 100 1000 1R0M 101□ 100□ BRL2012 100000 10000 Impedance Ω）（ 1000 1000 101M 100M 1R0M BRC1608 10000 2R2M Impedance Ω）（ 1000 R77M 100 R20M 10 1 10 1 1 10 100 1000 Frequency MHz）（ 1 10 100 1000 Frequency MHz）（ Frequency MHz）（＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound07_e-01 1 137 ■ PACKAGING ①Minimum Quantity Type BR C1608 BR L 2012 BR C2016 BR C2518 BR L 2518 BRFL2518 BR L3225 Standard Quantity [pcs] Paper Tape Embossed Tape ー 3,000 ー 3,000 ー 2,000 ー 2,000 ー 3,000 ー 3,000 ー 2,000 ⑤Reel size 2.5 or less （0.098max） φ60 ＋1 φ2.36 ＋0.039 ) （ −0 −0 10.0±1.5 (0.394±0.059) φ180 ＋0 φ7.09 ＋0 ) （ −3 −0.118 ②Tape Material ⑥Top Tape Strength The top tape requires a peel-off force of 0.2 to 0.7N in the direction of the arrow as illustrated below. ③Taping dimensions ◦Embossed Tape 8mm wide (0.315 inches wide) ◦Card board carrier tape 8mm wide (0.315 inches wide) Type BR C1608 BR L2012 BR C2016 BR C2518 BR L2518 BRFL2518 BR L3225 Chip cavity A B Insertion pitch F Tape thickness T K 1.2 max. （0.047） 1.2 max. （0.048） 1.9 max. （0.074） 1.0±0.10 1.9±1.0 4.0±0.1 0.25±0.05 （0.04±0.004） 0.076±0.004） 0.157±0.004） 0.01±0.002）（（（ 1.40±0.1 2.2±0.1 4.0±0.1 0.25±0.05 （0.056±0.004）（0.088±0.004）（0.157±0.004） 0.01±0.002）（ 1.75±0.1 2.1±0.1 4.0±0.1 0.3±0.05 （0.069±0.004）（0.083±0.004）（0.157±0.004） 0.012±0.002）（ 2.15±0.1 2.7±0.1 4.0±0.1 0.3±0.05 2.2 max. （0.085±0.004）（0.107±0.004） 0.157±0.004） 0.012±0.002）（0.086）（（ 2.3±0.1 2.8±0.1 4.0±0.1 0.3±0.05 1.45 max. （0.092±0.004）（0.112±0.004） 0.157±0.004） 0.012±0.002）（0.057）（（ 2.15±0.1 2.8±0.1 4.0±0.1 0.25±0.05 （0.085±0.004）（0.112±0.004） 0.157±0.004）（0.01±0.002）（ 2.8±0.1 3.5±0.1 4.0±0.1 0.25±0.05 （0.112±0.004） 0.140±0.004） 0.157±0.004） 0.01±0.002）（（（ 1.25 max. （0.049） 1.9 max. （0.074） Unit : mm (inch) ④Leader and Blank portion Blank portions Chip cavity Blank portions Leader 160 to 320mm （6.3 to 12.8 inches） 160 to 200 mm （6.3 to 7.87 inches） Direction of tape feed 400 to 560 mm （16.0 to 22.4 inches）＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound07_pack_e-01 1 wound07_pack-P1 ■ RELIABILITY DATA 1. Operating Temperature Range BRC1608, BRL2012, BRC2016, BRC2518, ー25∼＋105℃ BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, ー25∼＋120℃ NRH24/30, NRS50/60 Type NR10050 Type ー25∼＋105℃ 【Test Method and Remarks】 Including self-generated heat 2. Storage Temperature Range BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, ー40∼＋85℃ NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : 0 to 40℃ for the product with taping. NR10050 Type : 0∼40℃ for the product with taping. 3. Rated current BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Within the speciﬁed tolerance NRH24/30, NRS50/60 Type NR10050 Type 4. Inductance BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Within the speciﬁed tolerance NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : LCR Meter : HP 4285A or equivalent, Measuring frequency : Speciﬁed frequency NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : LCR Meter : HP 4285A or equivalent, 100KHz, 1V NR10050 Type : LCR Meter : HP 4263A or equivalent, 100KHz, 1V 5. DC Resistance BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Within the speciﬁed tolerance NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 DC ohmmeter : HIOKI 3227 or equivalent 6. Self resonance frequency BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Within the speciﬁcation NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : Inpedance analyzer/material analyzer : HP4291A or equivalent HP4191A, 4192A or equivalent 7. Temperature characteristic BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type BRL2012, BRC2016, BRL2518, BRL3225, BRC2518, BRFL2518 Inductance change : Within ±15% BRC1608 Inductance change : Within ±20% NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type Inductance change : Within ±20% NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : Measurement of inductance shall be taken at temperature range within −25℃∼＋85℃. With reference to inductance value at ＋20℃., change rate shall be calculated. Change of maximum inductance deviation in step 1 to 5 Temperature at step 1 Temperature at step 2 Temperature at step 3 Temperature at step 4 Temperature at step 5 20℃ Minimum operating temperature 20℃ (Standard temperature) Maximum oparating temperature 20℃ ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli-RP1 1 wound0407_reli_e-01 ■ RELIABILITY DATA 8. Resistance to ﬂexure of substrate BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type No damage. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : The test samples shall be soldered to the test board by the reﬂow. As illustrated below, apply force in the direction of the arrow indicating until deﬂection of the test board reaches to 2 mm. Force Rod 20 10 Test board size : 100×40×1.0 R230 Test board material : glass epoxy-resin Solder cream thickness : 0.12 (BR Series) Board 0.10 (NR30/40, NRV30, NRH24/30,NRG40) Test Sample R5 0.15 (NR50/60/80, NRS50/60) 45±2mm 45±2mm Land dimension BRC1608）（ 0.9 0.55 0.8 0.55 Land dimension BRL2012）（ Land dimension BRL3225）（ 2.7 1.0 1.6 1.0 Land dimension NR30, NRH30, NRV30）（ 2.7 0.8 1.4 0.8 Land dimension NR60, NRS60）（ 5.7 1.6 3.1 1.6 Land dimension NR, NRS50）（ 4.0 1.5 2.1 1.5 1.4 0.65 0.9 0.65 Land dimension ＢＣ2016）（Ｒ 1.8 0.7 0.8 0.7 Land dimension BRL2518,BRC2518,BRFL2518） Land dimension NRH24）（（ 1.95 0.65 1.5 0.65 0.7 0.75 0.7 2.0 Land dimension NR40, NRG40）（ 3.7 1.2 1.6 1.2 Land dimension NR80）（ 7.5 1.8 3.8 1.8 Printed board thickness : 1.0mm Unit : mm 9. Insulation resistance : between wires BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 10. Insulation resistance : between wire and core BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 11. Withstanding voltage : between wires and core BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 12. Adhesion of terminal electrode BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Shall not come off PC board. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : The test samples shall be soldered to the test board by the reﬂow. ・ Applied force : 10N to X and Y directions. ・ Duration : 5s. 10N, 5s ・ der cream thickness : 0.15mm. Sol BRC1608, NR10050 Type : ・ Applied force : 5N to X and Y directions. ・ Duration : 5s. 13. Resistance to vibration BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : The test samples shall be soldered to the test board by the reﬂow. Then it shall be submitted to below test conditions. Frequency Range Total Amplitude Sweeping Method Time 10∼55Hz 1.5mm (May not exceed acceleration 196m/s2) 10Hz to 55Hz to 10Hz for 1min. X Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2hrs of recovery under the standard condition sfter the test, followed by the measurement within 48hrs. ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli_e-01 1 wound0407_reli-RP2 ■ RELIABILITY DATA 14. Solderability BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, At least 90％ of surface of terminal electrode is covered by new solder. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050Type : The test samples shall be dipped in ﬂux, and then immersed in molten solder as shown in below table. Flux : Methanol solution containing rosin 25%. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : Solder Temperature Time 245±5℃ 5±1.0 sec. BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Solder Temperature Time 245±5℃ 5±0.5 sec. ※Immersion depth : All sides of mounting terminal shall be immersed. 15. Resistance to soldering heat BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : 0 3 times of reﬂow oven at 230℃ MIN. for 40sec. with peak temperature at 260＋5 ℃ for 5sec. ー : NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type The test sample shall be exposed to reﬂow oven at 230±5℃ for 40 seconds, with peak temperature at 260±5℃ for 5 seconds, 2 times. NR6020 Type : 0 The test sample shall be exposed to reﬂow oven at 230±5℃ for 40 seconds, with peak temperature at 250＋5 ℃ for 5 seconds, 2 times. ー Test board thickness : 1.0mm Test board material : glass epoxy-resin 16. Thermal shock BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : The test samples shall be soldered to the test board by the reﬂow. The test samples shall be placed at speciﬁed temperature for speciﬁed time by step 1 to step 4 as shown in below table in sequence. The temperature cycle shall be repeated 100 cycles. Step 1 2 3 4 Conditions of 1 cycle Temperature ( ℃) Duration (min) ー40±3 Room temperature ＋85±2 Room temperature 30±3 Within 3 30±3 Within 3 17. Damp heat BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% No signiﬁcant abnormality in appearance. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Temperature Humidity Time 60±2℃ 90∼95%RH 1000 hours. Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : The test samples shall be soldered to the test board by the reﬂow. The test samples shall be placed in thermostatic oven set at speciﬁed temperature and humidity as shown in below table. Temperature Humidity Time 60±2℃ 90∼95%RH 500±24hour ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli-RP3 1 wound0407_reli_e-01 ■ RELIABILITY DATA 18. Loading under damp heat BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Temperature Humidity Applied current Time 60±2℃ 90∼95％RH Rated current 1000hours. Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : The test samples shall be soldered to the test board by the reﬂow. The test samples shall be placed in thermostatic oven set at speciﬁed temperature and humidity and applied the rated current continuously as shown in below table. Temperature Humidity Applied current Time 60±2℃ 90∼95％RH Rated current 500±2hour 19. Low temperature life test BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Temperature Duration ー40±2℃ 1000hours Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : The test samples shall be soldered to the test board by the reﬂow. After that, the test samples shall be placed at test conditions as shown in below table. Temperature Time −40±3℃ 500±24hour 20. High temperature life test BRC1608, BRL2012, BRC2016, BRC2518, Inductance change : Within ±10% BRFL2518, BRL2518, BRL3225 Type No signiﬁcant abnormality in appearance. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type Inductance change : Within ±10% NR10050 Type No signiﬁcant abnormality in appearance. 【Test Method and Remarks】 BRC160 8, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Temperature Duration 85±2℃ 1000hours Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. NR10050 Type : Temperature Time 105±3℃ 500±24hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 21. Loading at high temperature life test BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Inductance change : Within ±10% NRH24/30, NRS50/60 Type No signiﬁcant abnormality in appearance. NR10050 Type 【Test Method and Remarks】 NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : The test samples shall be soldered to the test board by the reﬂow soldering. Temperature Applied current Time 85±2℃ Rated current 500±24hour 22. Standard condition BRC1608, BRL2012, BRC2016, BRC2518, Standard test condition : BRFL2518, BRL2518, BRL3225 Type Unless otherwise speciﬁed, temperature is 20±15％ and 65±20％of relative humidity. When there are question concerning measurement result : In order to provide correlation date, the test shall be condition of 20±2℃ NR30/40/50/60/80, NRV30, NRG40, of temperature, 65±5% relative humidity. NRH24/30, NRS50/60 Type Inductance is in accordance with our measured value. NR10050 Type ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli_e-01 1 wound0407_reli-RP4 ■ PRECAUTIONS SMD Inductors 1. Circuit Design ◆ Operating environment 1. The products described in this speciﬁcation are intended for use in general electronic equipment,(ofﬁce supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high Precautions reliability (trafﬁc systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design ◆Land pattern design 1. Please refer to a recommended land pattern. ◆Land pattern design Technical Surface Mounting consider・Mounting and soldering conditions should be checked beforehand. ations ・A pplicable soldering process to this products is reﬂow soldering only. Precautions 3. Considerations for automatic placement ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. Precautions 2. Mounting and soldering conditions should be checked beforehand. Technical ◆Adjustment of mounting machine consider1. When installing products, care should be taken not to apply distortion stress as it may deform the products. ations 4. Soldering ◆Reﬂow soldering 1. Please contact any of our ofﬁces for a reﬂow soldering, and refer to the recommended condition speciﬁed. 2. This products is reﬂow soldering only. 3. Please do not add any stress to a product until it returns in normal temperature after reﬂow soldering. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after conﬁrming of adhesion, temperature of resistance to soldering heat, soldering etc Precautions sufﬁciently. ◆Recommended conditions for using a soldering iron (NR10050 Type) ・Put the soldering iron on the land-pattern. ・Soldering iron's temperature - Below 350℃ ・Duration - 3 seconds or less ・The soldering iron should not directly touch the inductor. ◆Reﬂow soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. ・BRC160 8, BRL2012, BRL2518, BRC2016, BRL3225 Type BRC2518, BRFL2518 Recommended reﬂow condition (Pb free solder) Temperature ℃］［・NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type Recommended reﬂow condition (Pb free solder) Temperature ℃］［ 300 200 100 0 150∼180 5sec max Peak ： 250＋5/ー0℃ 30±10sec 230℃ min ・NR10050 Type Recommended reﬂow condition (Pb free solder) Temperature ℃］［ 300 200 100 0 150∼180 5sec max Peak ： 250＋0/ー5℃ 30±10sec 230℃ min Technical considerations 300 200 100 0 150∼180 5sec max Peak ： 260＋0/ー5℃ 30±10sec 230℃ min 90±30sec 90±30sec 90±30sec Ｈeating Time sec】【Ｈeating Time sec】【Ｈeating Time sec】【 5. Cleaning Precautions Technical considerations 6. Handling ◆Handling 1. Keep the product away from all magnets and magnetic objects. ◆Breakaway PC boards (splitting along perforations) 1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deﬂection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations Precautions 1. Please do not give the product any excessive mechanical shocks. 2. Please do not add any shock and power to a product in transportation. ◆Pick-up pressure 1. Please do not push to add any pressure to a winding part. Please do not give any shock and push into a ferrite core exposure part.。 ◆Packing 1. Please avoid accumulation of a packing box as much as possible. ◆Breakaway PC boards (splitting along perforations) 1. Planning pattern conﬁgurations and the position of products should be carefully performed to minimize stress. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. Technical 2. There is a case to be broken by the handling in transportation. considerations ◆Pick-up pressure 1. Damage and a characteristic can vary with an excessive shock or stress. ◆Packing 1. There is a case that transformation and a product of tape are damaged by accumulation of a packing box. 7. Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Precautions ・Recommended conditions Ambient temperature : 0∼40℃ Humidity : Below 70% RH The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping /packaging materials may take place. ◆ Cleaning conditions 1. Washing by supersonic waves shall be avoided. ◆ Cleaning conditions 1. If washing by supersonic waves, supersonic waves may cause broken products. Technical considerations ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli-RP5 1 wound0407_reli_e-01

下载 PDF

LB2016T1R0M 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“LB2016T1R0M”相匹配的价格&库存，您可以联系我们找货

免费人工找货

搜索历史

LB2016T1R0M

相关技术文章