Notice for TAIYO YUDEN Products
[ For General Electronic Equipment ]
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2018. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully
before practical application or use of our products.
Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or
equipment incorporating our products, which are caused under the conditions other than those specified in this
catalog or individual product specification sheets.
■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification
sheets are available.
■ Please conduct validation and verification of our products in actual condition of mounting and operating
environment before using our products.
■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA
equipment, home electric appliances, office equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be
sure to contact TAIYO YUDEN for further information before using the products for any equipment which may
directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment,
disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information
network equipment including, without limitation, telephone exchange, and base station).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g.,
aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control
equipment, undersea equipment, military equipment).
*Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g.,
in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN.
Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment.
When our products are used even for high safety and/or reliability-required devices or circuits of general electronic
equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to
install a protection circuit as necessary.
Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way
responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog
for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above.
■ Information contained in this catalog is intended to convey examples of typical performances and/or applications
of our products and is not intended to make any warranty with respect to the intellectual property rights or any
other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights.
■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and
TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products.
Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in
accordance with such agreement.
■ The contents of this catalog are applicable to our products which are purchased from our sales offices or
authorized distributors (hereinafter“TAIYO YUDEN’
s official sales channel”). Please note that the contents of this
catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’
s official sales
channel.
■ Caution for Export
Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export
Administration Regulations”
,“Foreign Exchange and Foreign Trade Control Law”of Japan, and other applicable
regulations. Should you have any questions on this matter, please contact our sales staff.
19
RADIAL LEADED INDUCTORS
RADIAL LEADED INDUCTORS
WAVE
WAVE
■PARTS NUMBER
L
H △
①
*Operating Temp. : -25～+105℃（Including self-generated heat）
L △
②
①Series name
Code
LH△
0
8
③
T
B
1
0 1
⑤
④
K
⑥
⑥Inductance tolerance
Code
J
K
M
N
Dimensions（D）［mm max.］
9.0
11.0
④Packaging
Code
NB
TB
⑦Internal code
Code
△△△
Packaging
Bulk（LHL）
Ammo packaging（LHL）
Nominal inductance［μH］
1.0
15
1000
／ LEADED INDUCTORS
INDUCTORS
Characteristics
Standard type Taping available
High current type
③Dimensions（D）
Code
08
10
△＝Blank space
⑤Nominal inductance
Code
（example）
1R0
150
102
※R＝Decimal point
Series name
Radial leaded inductor
②Characteristics
Code
L△
LC
△ △ △
⑦
Inductance tolerance
±5％
±10％
±20％
±30％
Internal code
Standard
■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
LHL /LHLC
D
H2
d
ℓ
F
LH
LH
LH
LH
Type
D
H2
ℓ
F
φd
L 08
LC08
L 10
LC10
9.0 max
（0.354 max）
11.0 max
（0.433 max）
9.5 max
（0.374 max）
14.0 max
（0.551 max）
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
0.6±0.05
（0.024±0.002）
0.6±0.05
（0.024±0.002）
Box
－
－
Standard quantity [pcs]
Bulk
Taping
100
1000
50
500
Unit：mm（inch）
i_leaded_LH_e-E05R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
107
■PARTS NUMBER
●LHL08
Parts number
EHS
Nominal inductance
［μH］
／ LEADED INDUCTORS
INDUCTORS
LH L 08[]1R0N
RoHS
1.0
LH L 08[]1R5M
RoHS
1.5
LH L 08[]2R2M
RoHS
2.2
LH L 08[]2R7M
RoHS
2.7
LH L 08[]3R3M
RoHS
3.3
LH L 08[]3R9M
RoHS
3.9
LH L 08[]4R7M
RoHS
4.7
LH L 08[]5R6M
RoHS
5.6
LH L 08[]6R8M
RoHS
6.8
LH L 08[]8R2M
RoHS
8.2
LH L 08[]100K
RoHS
10
LH L 08[]120K
RoHS
12
LH L 08[]150K
RoHS
15
LH L 08[]180K
RoHS
18
LH L 08[]220K
RoHS
22
LH L 08[]270K
RoHS
27
LH L 08[]330K
RoHS
33
LH L 08[]390K
RoHS
39
LH L 08[]470K
RoHS
47
LH L 08[]560K
RoHS
56
LH L 08[]680K
RoHS
68
LH L 08[]820K
RoHS
82
LH L 08[]101K
RoHS
100
LH L 08[]121K
RoHS
120
LH L 08[]151K
RoHS
150
LH L 08[]181K
RoHS
180
LH L 08[]221K
RoHS
220
LH L 08[]271K
RoHS
270
LH L 08[]331K
RoHS
330
LH L 08[]391K
RoHS
390
LH L 08[]471K
RoHS
470
LH L 08[]561K
RoHS
560
LH L 08[]681K
RoHS
680
LH L 08[]821K
RoHS
820
LH L 08[]102J
RoHS
1000
LH L 08[]122J
RoHS
1200
LH L 08[]152J
RoHS
1500
LH L 08[]182J
RoHS
1800
LH L 08[]222J
RoHS
2200
LH L 08[]272J
RoHS
2700
LH L 08[]332J
RoHS
3300
LH L 08[]392J
RoHS
3900
LH L 08[]472J
RoHS
4700
LH L 08[]562J
RoHS
5600
LH L 08[]682J
RoHS
6800
LH L 08[]822J
RoHS
8200
LH L 08[]103J
RoHS
10000
LH L 08[]123J
RoHS
12000
LH L 08[]153J
RoHS
15000
LH L 08[]183J
RoHS
18000
LH L 08[]223J
RoHS
22000
LH L 08[]273J
RoHS
27000
LH L 08[]333J
RoHS
33000
・ [] Please specify the packaging code. (TB: Taping, NB: Bulk)
Inductance
tolerance
Q
（min.）
Self-resonant
frequency
［MHｚ］（min..）
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Measuring frequency
［MHz］
±30％
±20％
±20％
±20％
±20％
±20％
±20％
±20％
±20％
±20％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
40
40
40
40
40
40
40
40
40
40
65
65
50
50
50
50
40
40
40
40
35
35
25
25
20
35
35
25
25
20
25
25
25
30
55
45
55
55
55
55
55
55
65
65
65
65
60
60
60
60
60
60
60
76
65
56
48
41
33
30
23
21
19
17
16
13
12
11
10
8.8
8.4
8.2
7.9
7.0
6.5
5.7
5.2
4.7
4.2
3.7
3.5
3.2
2.9
2.4
2.2
2.0
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.85
0.78
0.68
0.62
0.61
0.60
0.48
0.44
0.35
0.30
0.28
0.25
0.23
0.013
0.014
0.017
0.019
0.021
0.024
0.025
0.028
0.030
0.034
0.041
0.044
0.053
0.060
0.068
0.091
0.10
0.12
0.15
0.17
0.20
0.22
0.32
0.36
0.41
0.66
0.73
0.85
0.97
1.1
1.3
1.5
1.8
2.3
2.7
3.2
4.1
4.8
5.6
7.5
8.5
9.7
14
16
18
20
32
36
62
72
82
90
100
4.7
4.4
4.1
3.5
3.2
3.1
3.0
2.9
2.8
2.5
2.4
2.3
2.0
1.9
1.8
1.5
1.4
1.3
1.2
1.1
1.0
0.90
0.79
0.70
0.64
0.60
0.53
0.51
0.44
0.41
0.38
0.35
0.32
0.30
0.25
0.22
0.20
0.19
0.16
0.15
0.14
0.11
0.10
0.093
0.092
0.084
0.070
0.064
0.051
0.048
0.044
0.042
0.040
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
i_leaded_LH_e-E05R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
108
19
■PARTS NUMBER
●LHL10
Parts number
EHS
Nominal inductance
［μH］
Q
（min.）
Self-resonant
frequency
［MHｚ］（min..）
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Measuring frequency
［MHz］
±20％
±20％
±20％
±20％
±20％
±20％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
50
50
50
50
50
50
90
90
90
90
60
60
60
60
50
50
40
40
40
40
40
40
40
30
30
30
30
30
30
30
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
60
40
40
40
40
30
30
30
30
30
30
46
40
38
34
30
24
19
16
12
9.2
8.6
7.1
6.8
6.7
6.2
5.2
4.9
4.7
3.8
3.2
2.9
2.6
2.3
2.1
2.0
1.8
1.7
1.5
1.4
1.3
1.2
0.87
0.83
0.75
0.70
0.67
0.56
0.54
0.49
0.41
0.38
0.36
0.29
0.27
0.24
0.21
0.20
0.15
0.14
0.13
0.12
0.10
0.095
0.088
0.085
0.070
0.069
0.019
0.022
0.024
0.025
0.028
0.031
0.034
0.038
0.042
0.046
0.061
0.069
0.078
0.085
0.093
0.10
0.12
0.13
0.18
0.25
0.29
0.40
0.44
0.50
0.56
0.62
0.84
0.93
1.0
1.4
1.8
2.3
2.7
3.0
3.9
4.3
5.8
6.4
7.1
9.0
10
12
19
21
34
38
43
67
76
84
96
170
200
210
240
260
300
4.2
4.1
4.0
3.8
3.4
3.3
3.2
2.8
2.6
2.4
2.1
2.0
1.9
1.8
1.7
1.6
1.5
1.4
1.2
1.0
0.95
0.80
0.75
0.70
0.68
0.63
0.57
0.52
0.48
0.42
0.41
0.33
0.30
0.29
0.25
0.24
0.21
0.20
0.19
0.17
0.16
0.15
0.12
0.11
0.090
0.081
0.075
0.060
0.056
0.053
0.050
0.036
0.035
0.033
0.031
0.030
0.028
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0252MHz
L：1kHz， Q：0.0252MHz
L：1kHz， Q：0.0252MHz
／ LEADED INDUCTORS
INDUCTORS
LH L 10[]3R3M
RoHS
3.3
LH L 10[]3R9M
RoHS
3.9
LH L 10[]4R7M
RoHS
4.7
LH L 10[]5R6M
RoHS
5.6
LH L 10[]6R8M
RoHS
6.8
LH L 10[]8R2M
RoHS
8.2
LH L 10[]100K
RoHS
10
LH L 10[]120K
RoHS
12
LH L 10[]150K
RoHS
15
LH L 10[]180K
RoHS
18
LH L 10[]220K
RoHS
22
LH L 10[]270K
RoHS
27
LH L 10[]330K
RoHS
33
LH L 10[]390K
RoHS
39
LH L 10[]470K
RoHS
47
LH L 10[]560K
RoHS
56
LH L 10[]680K
RoHS
68
LH L 10[]820K
RoHS
82
LH L 10[]101K
RoHS
100
LH L 10[]121K
RoHS
120
LH L 10[]151K
RoHS
150
LH L 10[]181K
RoHS
180
LH L 10[]221K
RoHS
220
LH L 10[]271K
RoHS
270
LH L 10[]331K
RoHS
330
LH L 10[]391K
RoHS
390
LH L 10[]471K
RoHS
470
LH L 10[]561K
RoHS
560
LH L 10[]681K
RoHS
680
LH L 10[]821K
RoHS
820
LH L 10[]102J
RoHS
1000
LH L 10[]122J
RoHS
1200
LH L 10[]152J
RoHS
1500
LH L 10[]182J
RoHS
1800
LH L 10[]222J
RoHS
2200
LH L 10[]272J
RoHS
2700
LH L 10[]332J
RoHS
3300
LH L 10[]392J
RoHS
3900
LH L 10[]472J
RoHS
4700
LH L 10[]562J
RoHS
5600
LH L 10[]682J
RoHS
6800
LH L 10[]822J
RoHS
8200
LH L 10[]103J
RoHS
10000
LH L 10[]123J
RoHS
12000
LH L 10[]153J
RoHS
15000
LH L 10[]183J
RoHS
18000
LH L 10[]223J
RoHS
22000
LH L 10[]273J
RoHS
27000
LH L 10[]333J
RoHS
33000
LH L 10[]393J
RoHS
39000
LH L 10[]473J
RoHS
47000
LH L 10[]563J
RoHS
56000
LH L 10[]683J
RoHS
68000
LH L 10[]823J
RoHS
82000
LH L 10[]104J
RoHS
100000
LH L 10[]124J
RoHS
120000
LH L 10[]154J
RoHS
150000
・ [] Please specify the packaging code. (TB: Taping, NB: Bulk)
Inductance
tolerance
i_leaded_LH_e-E05R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
109
■PARTS NUMBER
●LHLC08
Parts number
EHS
Nominal inductance
［μH］
／ LEADED INDUCTORS
INDUCTORS
LH LC08[]1R0N
RoHS
1.0
LH LC08[]1R5M
RoHS
1.5
LH LC08[]2R2M
RoHS
2.2
LH LC08[]2R7M
RoHS
2.7
LH LC08[]3R3M
RoHS
3.3
LH LC08[]3R9M
RoHS
3.9
LH LC08[]4R7M
RoHS
4.7
LH LC08[]5R6M
RoHS
5.6
LH LC08[]6R8M
RoHS
6.8
LH LC08[]8R2M
RoHS
8.2
LH LC08[]100K
RoHS
10
LH LC08[]120K
RoHS
12
LH LC08[]150K
RoHS
15
LH LC08[]180K
RoHS
18
LH LC08[]220K
RoHS
22
LH LC08[]270K
RoHS
27
LH LC08[]330K
RoHS
33
LH LC08[]390K
RoHS
39
LH LC08[]470K
RoHS
47
LH LC08[]560K
RoHS
56
LH LC08[]680K
RoHS
68
LH LC08[]820K
RoHS
82
LH LC08[]101K
RoHS
100
LH LC08[]121K
RoHS
120
LH LC08[]151K
RoHS
150
LH LC08[]181K
RoHS
180
LH LC08[]221K
RoHS
220
LH LC08[]271K
RoHS
270
LH LC08[]331K
RoHS
330
LH LC08[]391K
RoHS
390
LH LC08[]471K
RoHS
470
LH LC08[]561K
RoHS
560
LH LC08[]681K
RoHS
680
LH LC08[]821K
RoHS
820
LH LC08[]102J
RoHS
1000
LH LC08[]122J
RoHS
1200
LH LC08[]152J
RoHS
1500
LH LC08[]182J
RoHS
1800
LH LC08[]222J
RoHS
2200
LH LC08[]272J
RoHS
2700
LH LC08[]332J
RoHS
3300
LH LC08[]392J
RoHS
3900
LH LC08[]472J
RoHS
4700
LH LC08[]562J
RoHS
5600
LH LC08[]682J
RoHS
6800
LH LC08[]822J
RoHS
8200
LH LC08[]103J
RoHS
10000
LH LC08[]123J
RoHS
12000
LH LC08[]153J
RoHS
15000
LH LC08[]183J
RoHS
18000
LH LC08[]223J
RoHS
22000
LH LC08[]273J
RoHS
27000
LH LC08[]333J
RoHS
33000
・ [] Please specify the packaging code. (TB: Taping, NB: Bulk)
Inductance
tolerance
Q
（min.）
Self-resonant
frequency
［MHｚ］（min..）
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Measuring frequency
［MHz］
±30％
±20％
±20％
±20％
±20％
±20％
±20％
±20％
±20％
±20％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
40
40
40
40
40
40
40
40
40
40
65
65
50
50
50
50
40
40
40
40
35
35
25
25
20
35
35
25
25
20
25
25
25
30
55
45
55
55
55
55
55
55
65
65
65
65
60
60
60
60
60
60
60
76
65
56
48
41
33
30
23
21
19
17
16
13
12
11
10
8.8
8.4
8.2
7.9
7.0
6.5
5.7
5.2
4.7
4.2
3.7
3.5
3.2
2.9
2.4
2.2
2.0
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.85
0.78
0.68
0.62
0.61
0.60
0.48
0.44
0.35
0.30
0.28
0.25
0.23
0.013
0.014
0.017
0.019
0.021
0.024
0.025
0.028
0.030
0.034
0.041
0.044
0.053
0.060
0.068
0.091
0.10
0.12
0.15
0.17
0.20
0.22
0.32
0.36
0.41
0.66
0.73
0.85
0.97
1.1
1.3
1.5
1.8
2.3
2.7
3.2
4.1
4.8
5.6
7.5
8.5
9.7
14
16
18
20
32
36
62
72
82
90
100
5.4
5.2
4.8
4.2
3.8
3.7
3.6
3.5
3.4
3.0
2.9
2.8
2.6
2.4
2.3
2.0
1.9
1.7
1.5
1.4
1.3
1.2
1.0
0.96
0.88
0.71
0.66
0.63
0.59
0.55
0.49
0.47
0.44
0.38
0.35
0.31
0.29
0.26
0.23
0.21
0.19
0.18
0.16
0.15
0.14
0.13
0.11
0.084
0.068
0.066
0.057
0.054
0.053
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
i_leaded_LH_e-E05R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
110
19
■PARTS NUMBER
●LHLC10
Parts number
EHS
Nominal inductance
［μH］
Q
（min.）
Self-resonant
frequency
［MHｚ］（min..）
DC Resistance
［Ω］（max.）
Rated current
［A］（max.）
Measuring frequency
［MHz］
±20％
±20％
±20％
±20％
±20％
±20％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±10％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
±5％
50
50
50
50
50
50
90
90
90
90
60
60
60
60
50
50
40
40
40
40
40
40
40
30
30
30
30
30
30
30
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
60
40
40
40
40
30
30
30
30
30
30
46
40
38
34
30
24
19
16
12
9.2
8.6
7.1
6.8
6.7
6.2
5.2
4.6
4.7
3.8
3.2
2.9
2.6
2.3
2.1
2.0
1.8
1.7
1.5
1.4
1.3
1.2
0.87
0.83
0.75
0.70
0.67
0.56
0.54
0.49
0.41
0.38
0.36
0.29
0.27
0.24
0.21
0.20
0.15
0.14
0.13
0.12
0.10
0.095
0.088
0.085
0.070
0.069
0.019
0.022
0.024
0.025
0.028
0.031
0.034
0.038
0.042
0.046
0.061
0.069
0.078
0.085
0.093
0.10
0.12
0.13
0.18
0.25
0.29
0.40
0.44
0.50
0.56
0.62
0.84
0.93
1.0
1.4
1.8
2.3
2.7
3.0
3.9
4.3
5.8
6.4
7.1
9.0
10
12
19
21
34
38
43
67
76
84
96
170
200
210
240
260
300
5.0
4.8
4.7
4.5
4.1
3.9
3.6
3.4
3.2
3.0
2.8
2.7
2.6
2.4
2.3
2.1
2.0
1.8
1.5
1.3
1.2
1.0
0.97
0.90
0.86
0.75
0.65
0.61
0.57
0.50
0.48
0.40
0.37
0.36
0.32
0.30
0.26
0.25
0.24
0.21
0.20
0.18
0.14
0.13
0.11
0.10
0.095
0.076
0.068
0.065
0.061
0.045
0.043
0.041
0.038
0.037
0.035
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
2.52
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.796
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
0.252
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0796MHz
L：1kHz， Q：0.0252MHz
L：1kHz， Q：0.0252MHz
L：1kHz， Q：0.0252MHz
／ LEADED INDUCTORS
INDUCTORS
LH LC10[]3R3M
RoHS
3.3
LH LC10[]3R9M
RoHS
3.9
LH LC10[]4R7M
RoHS
4.7
LH LC10[]5R6M
RoHS
5.6
LH LC10[]6R8M
RoHS
6.8
LH LC10[]8R2M
RoHS
8.2
LH LC10[]100K
RoHS
10
LH LC10[]120K
RoHS
12
LH LC10[]150K
RoHS
15
LH LC10[]180K
RoHS
18
LH LC10[]220K
RoHS
22
LH LC10[]270K
RoHS
27
LH LC10[]330K
RoHS
33
LH LC10[]390K
RoHS
39
LH LC10[]470K
RoHS
47
LH LC10[]560K
RoHS
56
LH LC10[]680K
RoHS
68
LH LC10[]820K
RoHS
82
LH LC10[]101K
RoHS
100
LH LC10[]121K
RoHS
120
LH LC10[]151K
RoHS
150
LH LC10[]181K
RoHS
180
LH LC10[]221K
RoHS
220
LH LC10[]271K
RoHS
270
LH LC10[]331K
RoHS
330
LH LC10[]391K
RoHS
390
LH LC10[]471K
RoHS
470
LH LC10[]561K
RoHS
560
LH LC10[]681K
RoHS
680
LH LC10[]821K
RoHS
820
LH LC10[]102J
RoHS
1000
LH LC10[]122J
RoHS
1200
LH LC10[]152J
RoHS
1500
LH LC10[]182J
RoHS
1800
LH LC10[]222J
RoHS
2200
LH LC10[]272J
RoHS
2700
LH LC10[]332J
RoHS
3300
LH LC10[]392J
RoHS
3900
LH LC10[]472J
RoHS
4700
LH LC10[]562J
RoHS
5600
LH LC10[]682J
RoHS
6800
LH LC10[]822J
RoHS
8200
LH LC10[]103J
RoHS
10000
LH LC10[]123J
RoHS
12000
LH LC10[]153J
RoHS
15000
LH LC10[]183J
RoHS
18000
LH LC10[]223J
RoHS
22000
LH LC10[]273J
RoHS
27000
LH LC10[]333J
RoHS
33000
LH LC10[]393J
RoHS
39000
LH LC10[]473J
RoHS
47000
LH LC10[]563J
RoHS
56000
LH LC10[]683J
RoHS
68000
LH LC10[]823J
RoHS
82000
LH LC10[]104J
RoHS
100000
LH LC10[]124J
RoHS
120000
LH LC10[]154J
RoHS
150000
・ [] Please specify the packaging code. (TB: Taping, NB: Bulk)
Inductance
tolerance
i_leaded_LH_e-E05R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
111
RADIAL LEADED INDUCTORS
■PACKAGING
①Minimum Quantity
Standard quantity [pcs]
Bulk
Taped
100
1000
50
500
100
1000
50
500
Type (EIA)
LHL 08
LHL 10
LHLC08
LHLC10
②Bulk dimensions
●LHL08, LHL10
Type
LHL08
LHL10
φD（max）
9.0
（0.354）
11.0
（0.433）
Dimensions
F＊
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
H2（max）
9.5
（0.374）
14.0
（0.551）
ℓ
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
φd
0.6±0.05
（0.024±0.002）
0.6±0.05
（0.024±0.002）
Unit：mm（inch）
*Measured at the base of the leads.
D
H1
H
H2
P
P0
P1
P2
F
h
W
W0
W1
W2
D0
φd
t
LHL08
φ9.0 max
（φ0.354 max）
30.5 max
（1.20 max）
18.0＋2.0/－0.0
（0.709＋0.079/－0.000）
9.5 max
（0.374 max）
12.7±1.0
（0.500±0.039）
12.7±0.3※1
（0.500±0.012）
3.85±0.7
（0.152±0.028）
6.35±1.3
（0.250±0.051）
5.0＋0.8/－0.2
（0.197＋0.031/0.008）
0.0±2.0
（0.0±0.079）
18.0＋1.0/－0.5
（0.709＋0.039/－0.020）
12.5 min
（0.492 min）
9.0±0.5
（0.354±0.020）
3.0 max※2
（0.118 max）
φ4.0±0.2
（φ0.158±0.008）
φ0.6±0.05
（φ0.024±0.002）
0.6±0.3
（0.024±0.012）
LHL10
φ11.0 max
（φ0.433 max）
34.0 max
（1.34 max）
18.0＋2.0/－0.0
（0.709＋0.079/－0.000）
14.0 max
（0.551 max）
12.7±1.0
（0.500±0.039）
12.7±0.3※1
（0.500±0.012）
3.85±0.7
（0.152±0.028）
6.35±1.3
（0.250±0.051）
5.0＋0.8/－0.2
（0.197＋0.031/－0.008）
0.0±2.0
（0.0±0.079）
18.0＋1.0/－0.5
（0.709＋0.039/－0.020）
12.5 min
（0.492 min）
9.0±0.5
（0.354±0.020）
3.0 max※2
（0.118 max）
φ4.0±0.2
（φ0.158±0.008）
φ0.6±0.05
（φ0.024±0.002）
0.6±0.3
（0.024±0.012）
Unit：mm（inch）
※1 Accumulated error for 20 pitches is 1mm.
※2 Bonding tape must not protrude from the base tape.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_LH_pack_e-E04R01
●LHLC08, LHLC10
Type
LHLC08
LHLC10
φD（max）
9.0
（0.354）
11.0
（0.433）
Dimensions
F＊
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
H2（max）
9.5
（0.374）
14.0
（0.551）
ℓ
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
φd
0.6±0.05
（0.024±0.002）
0.6±0.05
（0.024±0.002）
Unit：mm（inch）
*Measured at the base of the leads.
D
H1
H
H2
P
P0
P1
P2
F
H
W
W0
W1
W2
D0
φd
t
LHLC08
φ9.0max
(φ0.354max）
30.5max
（1.20max）
18.0＋2.0/－0.0
（0.709＋0.079/－0.000）
9.5max
（0.374max）
12.7±1.0
（0.500±0.039）
12.7±0.3※1
（0.500±0.012）
3.85±0.7
（0.152±0.028）
6.35±1.3
（0.250±0.051）
5.0＋0.8/－0.2
（0.197＋0.031/－0.008）
0.0±2.0
（0.0±0.079）
18.0＋1.0/－0.5
（0.709＋0.039/－0.020）
12.5min
（0.492min）
9.0±0.5
（0.354±0.020）
3.0max※2
（0.118max）
φ4.0±0.2
（φ0.158±0.008）
φ0.6±0.05
（φ0.024±0.002）
0.6±0.3
（0.024±0.012）
LHLC10
φ11.0max
（φ0433max）
34.0max
（1.34max）
18.0＋2.0/－0.0
（0.709＋0.079/－0.000）
14.0max
（0.551max）
12.7±1.0
（0.500±0.039）
12.7±0.3※1
（0.500±0.012）
3.85±0.7
（0.152±0.028）
6.35±1.3
（0.250±0.051）
5.0＋0.8/－0.2
（0.197＋0.031/－0.008）
0.0±2.0
（0.0±0.079）
18.0＋1.0/－0.5
（0.709＋0.039/－0.020）
12.5min
（0.492min）
9.0±0.5
（0.354±0.020）
3.0max※2
（0.118max）
φ4.0±0.2
（φ0.158±0.008）
φ0.6±0.05
（φ0.024±0.002）
0.6±0.3
（0.024±0.012）
Unit：mm（inch）
※1 Accumulated error for 20 pitches is 1mm.
※2 Bonding tape must not protrude from the base tape.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_LH_pack_e-E04R01
AXIAL LEADED INDUCTORS（CAL Type）、
RADIAL LEADED INDUCTORS（LH Type）、
LEADED FERRITE BEAD INDUCTORS（ FB Series A Type／R Type）
■RELIABILITY DATA
1. Operating temperature Range
CAL45 Type
Specified Value
LHL□□□
－25～＋ 105℃
FBA/FBR
CAL45 Type
Test Methods and
Remarks
LHL□□□
Including self-generated heat
FBA/FBR
2. Storage temperature Range
CAL45 Type
Specified Value
LHL□□□
－40～＋ 85℃（Except for taping condition）
FBA/FBR
3. Rated current
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
The maximum DC value having inductance within 10% and temperature increase within 40℃ by the application of DC bias.
LHL□□□ :
The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10：within 30%) and temperature increase within the
following specified temperature by the application of DC bias.
Reference temperature
: 25℃（LHL08, LHL10）
: 40℃（LHLC08, LHLC10）
FBA/FBR :
No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be
within ±20% of the initial value.
This is not guaranteed for electrical characteristics during current application.
4. Impedance
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
Test Methods and
Remarks
FBA/FBR :
Measuring equipment
Measuring frequency
Within the specified tolerance
: Impedance analyzer (HP4191A) or its equivalent
: Specified frequency
5. Inductance
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Measuring equipment
Measuring frequency
LHL□□□ :
Measuring equipment
Measuring frequency
: LCR meter (HP4285A + HP42851A or its equivalent)
: Specified frequency
: LCR meter (HP4285A＋HP42851A or its equivalent)
: LCR meter (HP4263A) or its equivalent (at 1kHz)
: Specified frequency
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
6. Q
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
LHL□□□
Measuring equipment
Measuring frequency
: LCR meter (HP4285A＋HP42851A or its equivalent)
: LCR meter (HP4263A) or its equivalent (at 1kHz)
: Specified frequency
7. DC Resistance
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
Measuring equipment
: DC ohmmeter
8. Self resonance frequency
CAL45 Type
Specified Value
LHL□□□
Within the specified tolerance
FBA/FBR
Test Methods and
Remarks
LHL□□□
Measuring equipment
: (HP4191A, 4192A) its equivalent
9. Temperature characteristic
CAL45 Type
Specified Value
LHL□□□
△L/L : Within ±7%
FBA/FBR
Test Methods and
Remarks
Change of maximum inductance deviation in step 1 to 5
Temperature (℃)
Step
LHL□□□
1
20
2
Minimum operating temperature
3
20 (Standard temperature)
4
Maximum operating temperature
5
20
10. Tensile strength test
CAL45 Type
Specified Value
LHL□□□
No abnormality such as cut lead, or looseness.
FBA/FBR
Test Methods and
Remarks
CAL45 Type : Apply the stated tensile force progressively in the direction to draw terminal.
force (N)
duration (s)
10
10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Nominal wire diameter tensile φd (mm)
force (N)
duration (s)
0.3＜φd≦0.5
5
30±5
0.5＜φd≦0.8
10
0.8＜φd≦1.2
25
FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the
of the component during 10±1 seconds.
axial direction
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
11. Over current
Specified Value
CAL45 Type
No emission of smoke no firing.
LHL□□□
There shall be no scorch or short of wire.
LHLC08, LHLC10 : There shall be no firing.
FBA/FBR
Test Methods and
Remarks
LHL□□□・CAL45 Type ：
Measuring current
: Rated current×2
Duration
: 5 min.
Number of measuring
: one time
12. Terminal strength : bending
CAL45 Type
Specified Value
LHL□□□
No abnormality such as cut lead, or looseness.
FBA/FBR
CAL45 Type :
Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the
initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter
Mass reference
Bending force
tensile
weight
0.3＜ φ d≦0.5
2.5
0.25
0.5＜ φ d≦0.8
5
0.50
Test Methods and
Remarks
LHL□□□・FBA/FBR :
Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the
initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter
Mass reference
Bending force
tensile
weight
0.3＜φd≦0.5
2.5
0.25
0.5＜φd≦0.8
5
0.5
0.8＜φd≦1.2
10
1.0
13. Insulation resistance : between the terminals and body
CAL45 Type
Specified Value
LHL□□□
100MΩmin.
FBA/FBR
Test Methods and
Remarks
LHL□□□ :
Applied voltage
Duration
: 500 VDC
: 60 sec.
14. Insulation resistance : between terminals and core
CAL45 Type
Specified Value
LHL□□□
FBA/FBR
Test Methods and
Remarks
FBA/FBR :
Applied voltage
Duration
1MΩmin.
: 100 VDC
: 60±5 sec.
15. Withstanding : between the terminals and body
CAL45 Type
Specified Value
LHL□□□
No abnormality such as insulation damage
FBA/FBR
Test Methods and
Remarks
LHL□□□ :
According to JIS C5101-1.
Metal global method
Applied voltage
: 500 VDC
Duration
: 60 sec.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
16. DC bias characteristic
CAL45 Type
Specified Value
△L/L : Within －10%
LHL□□□
FBA/FBR
Test Methods and
Remarks
CAL45 Type : Measure inductance with application of rated current using LCR meter to compare it with the initial value.
17. Body strength
CAL45 Type
Specified Value
No abnormality as damage.
LHL□□□
FBA/FBR
CAL45 Type :
Applied force
Duration
Speed
FBA :
Applied force
Duration
No abnormality such as cracks on body.
:50N
: 10 sec.
: Shall attain to specified force in 2 sec.
: 50±3N
: 30±1 sec.
Test Methods and
Remarks
18. Resistance to vibration
Specified Value
Test Methods and
Remarks
CAL45 Type
△L/L : Within ±5%
LHL□□□
Appearance : No abnormality
△L/L : Within ±5%
Q change : Within ±30%
FBA/FBR
Appearance : No abnormality
Impedance change : Within ±20%
CAL45 Type :
Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range
: 10 to 55 to 10Hz (1min.)
Amplitude
: 1.5mm
Mounting method
: Soldering onto printed board.
Recovery
: At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□・FBA/FBR :
Directions
: 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range
: 10 to 55 to 10Hz (1min.)
Amplitude
: 1.5mm
Mounting method
: Soldering onto printed board.
19. Resistance to shock
CAL45 Type
Specified Value
No significant abnormality in appearance
LHL□□□
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Drop test
Impact material
Height
Total number of drops
: concrete or vinyl tile
: 1m
: 10 times
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
20. Solderability
Specified Value
Test Methods and
Remarks
CAL45 Type
At least 75％ of terminal electrode is covered by new solder.
LHL□□□
At least 75％ of terminal electrode is covered by new solder.
FBA/FBR
At least 90％ of terminal electrode is covered by new solder.
CAL45 Type :
Solder temperature
Duration
LHL□□□ :
Solder temperature
Duration
Immersion depth
FBA/FBR :
Solder temperature
Duration
Immersion depth
: 230±5℃
: 2±0.5 sec.
: 235±5℃
: 2±0.5 sec.
: Up to 1.5mm from bottom of case.
: 230±5℃
: 3±1 sec.
: Up to 1.5mm from terminal root.
21. Resistance to soldering heat
Specified Value
CAL45 Type
△L/L : Within ±5%
LHL□□□
No significant abnormality in appearance
Inductance change : Within ±5%
Q change : Within ±30%
FBA/FBR
No significant abnormality in appearance
Impedance change : Within ±20%
CAL45 Type :
Solder temperature
Duration
Immersed conditions
Recovery
:
:
:
:
LHL□□□ :
Solder bath method :
270±5℃
5±0.5 sec. One time
Inserted into substrate with t=1.6mm
At least 1hr of recovery under the standard condition after the test, followed by the measurement within
2hrs.
Solder temperature
Duration
Manual soldering :
Caution
Recovery
:
:
:
:
:
:
:
:
260±5℃
10±1 sec.
Up to 1.5mm from the bottom of case.
350±10℃ (At the tip of soldering iron)
5±1 sec.
Up to 1.5mm from the bottom of case.
No excessive pressing shall be applied to terminals.
1 to 2hrs of recovery under the standard condition after the test.
Solder temperature
Duration
Immersion depth
Solder temperature
Duration
Immersion depth
Recovery
:
:
:
:
:
:
:
260±5℃
10±1 sec.
Up to 1.5mm from the terminal root.
350±5℃
3±1 sec.
Up to 1.5mm from the terminal root.
3hrs of recovery under the standard condition after the test.
Solder temperature
Duration
Test Methods and
Remarks
FBA/FBR :
Solder bath method:
Condition 1:
Condition 2 :
22. Resistance to solvent
CAL45 Type
Specified Value
Please avoid the ultrasonic cleaning of this product.
LHL□□□
No significant abnormality in appearance
Impedance change : Within ±20%
FBA/FBR
Test Methods and
Remarks
FBA/FBR :
Solvent temperature
Duration
Solvent type
Recovery
:
:
:
:
20～25℃
30±5 sec.
Acetone
3hrs of recovery under the standard condition after the test.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
23. Thermal shock
Specified Value
CAL45 Type
△L/L : Within ±10%
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30%
FBA/FBR
Appearance : No abnormality
Impedance change : Within ±20%
CAL45 Type：Conditions for 1cycle
Step
Temperature (℃)
1
－25＋0/－3
2
Room temperature
3
＋85＋2/－0
4
Room temperature
Number of cycles
Recovery
Test Methods and
Remarks
Duration (min.)
30±3
Within 3
30±3
Within 3
: 5 cycles
: At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the
measurement within 2hrs.
LHL□□□・FBA/FBR： According to JIS C60068-2-14.
Conditions for 1 cycle
Step
Temperature (℃)
1
Minimum operating temperature
2
Room temperature
3
Maximum operating temperature
4
Room temperature
Number of cycles
Recovery
:
:
:
:
Duration (min.)
30±3
Within 3
30±3
Within 3
10 cycles 〔LHL□□□〕
5 cycles (FBA/ FBR)
1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 〔LHL□□□〕
3hrs of recovery under the standard condition after the removal from the test chamber. (FBA/ FBR)
24. Damp heat
CAL45 Type
Specified Value
△L/L : Within ±10%
LHL□□□
Appearance：No abnormality
Impedance change：Within ±20%
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Temperature
Humidity
Duration
Recovery
FBA/FBR :
Temperature
Humidity
Duration
Recovery
: 40±2℃
: 90～95%RH
: 1000 hrs
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
:
:
:
:
60±2℃
90～95%RH
1000 hrs
3hrs of recovery under the standard condition after the removal from the test chamber.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
25. Loading under damp heat
Specified Value
CAL45 Type
△L/L : Within ±10%
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30%
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Temperature
Humidity
Duration
Applied current
Recovery
LHL□□□ :
Temperature
Humidity
Duration
Applied current
Recovery
: 40±2℃
: 90～95%RH
: 1000 hrs
: Rated current
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
:
:
:
:
:
40±2℃
90～95%RH
1000＋48/-0 hrs
Rated current
1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
CAL45 Type
Specified Value
△L/L : Within ±10%
LHL□□□
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Temperature
Duration
Applied current
Recovery
: 85±2℃
: 1000 hrs
: Rated current
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
Specified Value
CAL45 Type
△L/L : Within ±10%
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30%
FBA/FBR
Test Methods and
Remarks
CAL45 Type :
Temperature
Duration
Recovery
LHL□□□ :
Temperature
Duration
Recovery
: －25±2℃
: 1000 hrs
: At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
:－40±3℃
: 1000＋48/-0 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
28. High temperature life test
CAL45 Type
Specified Value
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30%
FBA/FBR
Test Methods and
Remarks
LHL□□□ :
Temperature
Duration
Recovery
: 105±2℃
: 1000＋48/-0 hrs
: 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-E06R01
AXIAL LEADED INDUCTORS（CAL Type）、
RADIAL LEADED INDUCTORS（LH Type）、
LEADED FERRITE BEAD INDUCTORS（FB Series A Type／R Type）
■PRECAUTIONS
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions
Technical
considerations
◆Design
1. Please design insertion pitches as matching to that of leads of the component on PCBs.
◆Design
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will
cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
Precautions
Technical
considerations
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire inductor in the flux during the soldering operation.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering
heat, soldering etc sufficiently.
◆Recommended conditions for using a soldering iron:
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. As for reflow soldering, please contact our sales staff.
Technical
considerations
◆Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
◆Recommended conditions for using a soldering iron
If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade
the reliability of the products.
5. Cleaning
Precautions
Technical
considerations
◆Cleaning conditions
1. CAL type, LH type
Please do not do cleaning by a supersonic wave.
◆Cleaning conditions
1. CAL type, LH type,
If washing by supersonic waves, supersonic waves may deform products.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_prec_e-E02R01
6. Handling
Precautions
Technical
considerations
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
2. LH type
If inductors are dropped onto the floor or a hard surface they should not be used.
◆Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading /
fragile item).
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. LH type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead wire could be deformed by a fall or an excessive shock.
7. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
Recommended conditions
・Ambient temperature 0～40℃
・Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
considerations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_prec_e-E02R01
工商网监
湘ICP备2023018690号
