NRH2410T150MN

厂商：
TAIYO-YUDEN(太诱)
封装：
IND_2.4X2.4MM_SM
描述：
功率电感 15µH ±20% 1.02Ω IND_2.4X2.4MM_SM

数据手册：

下载NRH2410T150MN.pdf

立即购买

数据手册
价格&库存

NRH2410T150MN 数据手册

Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2009. All of the contents speciﬁed herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those speciﬁed in this catalog or individual speciﬁcation. ■ Please contact Taiyo Yuden Co., Ltd. for further details of product speciﬁcations as the individual speciﬁcation is available. ■ Please conduct validation and veriﬁcation of products in actual condition of mounting and operating environment before commercial shipment of the equipment. ■ All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the ﬁeld such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct inﬂuence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in ﬁelds such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufﬁcient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. ■ The contents of this catalog are applicable to the products which are purchased from our sales ofﬁces or distribu“ tors (so called TAIYO YUDEN’ ofﬁcial sales channel” s ). It is only applicable to the products purchased from any of TAIYO YUDEN’ of ﬁcial sales channel. s ■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. ■ Caution for export Certain items in this catalog may require speciﬁc procedures for export according to“Foreign Exchange and Foreign Trade Control Law”of Japan,“U.S. Export Administration Regulations” and other applicable regulations. , Should you have any question or inquiry on this matter, please contact our sales staff. Should you have any question or inquiry on this matter, please contact our sales staff. 1 notice_e-01 SMD INDUCTORS SMALL AND LARGE CURRENT TYPE REFLOW ■ FEATURES ◦Small and Low proﬁle inductor. ◦It corresponds to High current. ◦Simple and original magnetic shield structure. ◦Durable structure against dropping impact. ■ APPLICATIONS ◦For small DC/DC converter (cellular Phone, HDD, DVC, DSC, PDA, LCD display etc). ■ ORDERING CODE N R ❶ H 2 4 ❷ 1 0 T△ T△1 ❸ ❸Packaging Tape & Reel △＝Blank Space example 0 ❹ 0 M○○○ ❺ ❺Inductance tolerance M ±20% N ±30% ❻ ❻Internal code ○○○ Standard products ○＝Blank Space ❶Type NRH NRS Coating resin speciﬁcation NRV ❷External dimensions （W×L×H） example ❹Nominal inductance 〔μH〕 2R2 100 101 2.2 10 100 2410 3010 3012 5012 5014 5020 6010 2.4×2.4×1.0mm 3.0×3.0×1.0mm 3.0×3.0×1.2mm 5.0×5.0×1.2mm 5.0×5.0×1.4mm 5.0×5.0×2.0mm 6.0×6.0×1.0mm ※R＝decimal point ■ E XTERNAL DIMENSIONS/STANDARD QUANTITY L H e W f e W e L H e f Δ ℓ Δe Δe Standard Quantity [pcs] Tape & Reel 1000 1000 800 1000 Type NRH2410 L W H e f Standard Quantity [pcs] Tape & Reel 2500 2000 2000 Type NRS5012 NRS5014 NRS5020 NRS6010 L W H e Δe f Δℓ 2.4±0.1 2.4±0.1 1.0 max 0.6±0.2 1.45±0.2 （0.095±0.004）（0.095±0.004）（0.039 max）（0.024±0.008）（0.057±0.008） 1.0 max NRH3010 3.0±0.1 （0.039 max） 0.9±0.2 1.9±0.2 3.0±0.1 NRH3012 （0.118±0.004）（0.118±0.004） 1.2 max （0.035±0.008）（0.075±0.008） NRV3012 （0.047 max） Recommended Land Patterns Unit：mm inch）（ 1.2 max （0.047 max） 4.9±0.2 4.9±0.2 1.4 max 1.2±0.2 0.3±0.2 3.3±0.2 1.3±0.3 （0.193±0.008）（0.193±0.008）（0.055 max）（0.047±0.008）（0.011±0.008）（0.130±0.008）（0.051±0.011） 2.0 max （0.079 max） 0.3±0.2 4.0±0.2 2.3±0.3 6.0±0.2 6.0±0.2 1.0 max 1.35±0.2 （0.236±0.008）（0.236±0.008）（0.039 max）（0.053±0.008）（0.011±0.008）（0.157±0.008）（0.091±0.011）【NRS6010】 4.7 Unit：mm inch）（【NRS5012, NRS5014, NRS5020】 3.6 2.7 4.0 5.7 【NRH2410】 1.45 2.0 0.7 0.7 【NR3010, NRH3012, NRV3012】 2.2 0.8 0.8 1.5 1.5 1.6 1.6 ■ AVAILABLE INDUCTANCE RANGE Range Type Imax [mA] NRH2410 Rdc±20％ Imax ［Ω］[mA] NRH3010 Rdc±20％ Imax ［Ω］[mA] NRH3012 Rdc±20％ Imax ［Ω］[mA] NRV3012 Rdc±20％ Imax ［Ω］[mA] 2300 NRS5012 Rdc±20％ Imax ［Ω］[mA] 0.053 NRS5014 Rdc±20％ Imax ［Ω］[mA] NRS5020 Rdc±20％ Imax ［Ω］[mA] NRS6010 Rdc±20％［Ω］ Inductance μH］［ 1.0 1410 2.2 4.7 10 22 100 450 300 0.070 1480 0.065 1710 0.048 1100 0.120 3600 2800 0.045 0.100 1300 900 0.021 1900 0.120 1000 0.260 0.090 0.270 0.690 600 1.47 380 0.350 720 0.770 500 0.270 0.630 850 0.420 1800 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 128 1 wound05_e-01 ■ PART NUMBERS ●NRH 2410 Shielded type Ordering code NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T NRH2410T R68NN 4 1R0NN 4 1R5MN 2R2MN 3R3MN 4R7MN 6R8MN 100MN 150MN 220MN EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 120 10 6 94 77 56 50 43 32 27 22 DC Resistance [Ω] (±20%) 0.060 0.070 0.110 0.150 0.220 0.290 0.410 0.690 1.02 1.47 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 2, 200 1,570 1,800 1,410 1,550 1,160 1, 290 970 1,000 770 880 670 750 570 550 450 470 370 39 0 300 Measuring frequency 〔kHz〕 100 ±20％ ●NRH 3010 Type FERRITE PRODUCTS Ordering code NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T NRH3010T 1R2N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.2 1.5 2.2 3.3 4.7 6.8 10 15 22 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 120 99 86 64 50 44 34 25 22 DC Resistance [Ω] (±20%) 0.065 0.075 0.083 0.130 0.170 0.250 0.350 0.550 0.770 ±20％〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 1,700 1,480 1,440 1,370 1,300 1,300 1,000 1,030 850 900 70 0 745 60 0 620 450 480 380 410 Measuring frequency 〔kHz〕 100 ●NRH 3012 Type Ordering code NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T NRH3012T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M 150M 220M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 111 95 78 61 50 43 32 26 22 DC Resistance [Ω] (±20％) 0.048 0.055 0.075 0.100 0.130 0.190 0.270 0.450 0.630 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 2, 200 1,710 1,700 1,600 1,500 1,370 1, 200 1,210 1,000 1,060 850 890 730 720 530 570 50 0 500 Measuring frequency 〔kHz〕 100 ±20％ ●NRV 3012 Type EHS (Environmental Hazardous Substances) RoHS Inductance [μH] 2.2 Inductance Tolerance ±20％ Self-resonant frequency 〔MHz〕 min.) ( 70 DC Resistance [Ω] (±20％) 0.120 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 1,800 1,100 Measuring frequency 〔kHz〕 100 Ordering code NRV3012T 2R2M ●NRS 5012 Type Ordering code NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T NRS5012T 1R0N 1R5N 2R2M 3R3M 4R7M 6R8M 100M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 Inductance Tolerance ±30％ Self-resonant frequency 〔MHz〕 min.) ( 100 86 70 48 40 36 26 DC Resistance [Ω] (±20％) 0.053 0.070 0.085 0.160 0.180 0.260 0.420 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 4,500 2,300 3,800 2,200 3,100 2,000 2,400 1,450 2, 200 1,400 1,700 1,100 1,400 850 Measuring frequency 〔kHz〕 100 ±20％ ●NRS 5014 Type EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS Inductance [μH] 1.2 2.2 3.3 4.7 Ordering code NRS5014T 1R2N NRS5014T 2R2N NRS5014T 3R3N NRS5014T 4R7N Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 86 56 48 41 DC Resistance [Ω] (±20％) 0.045 0.065 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 3,800 2,800 2,350 2,050 2,800 2,300 2,100 1,800 Measuring frequency 〔kHz〕 ±30％ 0.080 0.100 100 ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound05_e-01 1 129 ■ PART NUMBERS ●NRS 5020 Type Ordering code NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T NRS5020T 1R0N 1R5N 2R2N 3R3N 4R7M 6R8M 100M 150M 220M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 81 68 57 46 37 30 24 20 17 DC Resistance [Ω] (±20％) 0.021 0.026 0.035 0.048 0.060 0.090 0.120 0.165 0.260 〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 4,000 3,600 3,350 3,200 2,900 2,900 2,400 2,400 2,000 2,000 1,600 1,650 1,300 1,450 1,100 1,200 90 0 1,000 Measuring frequency 〔kHz〕 ±30％ 100 ±20％ ●NRS 6010 Type Ordering code NRS6010T NRS6010T NRS6010T NRS6010T NRS6010T NRS6010T 1R5N 2R2N 3R3N 4R7N 6R8N 100M EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS Inductance [μH] 1.5 2.2 3.3 4.7 6.8 10 Inductance Tolerance Self-resonant frequency 〔MHz〕 min.) ( 90 65 50 38 30 25 DC Resistance [Ω] (±20％) 0.090 0.110 0.135 0.165 0.220 0.270 ±30％ ±20％〔 Rated current ※） mA〕 Saturation Temperature rise current current Idc1 Idc2 1,900 2,400 1,900 1,700 1,600 1,500 1,300 1,400 1, 200 1,200 1,000 1,100 Measuring frequency 〔kHz〕 100 ※） saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃) The ※） temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃) The ※） rated current is the DC current value that satisﬁes both of current value saturation current value and temperature rise current value. The ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 130 1 wound05_e-01 ■ ELECTRICAL CHARACTERISTICS ■ DC Bias characteristics NRH 2410 100 100 （Measured by HP4285A） NRH 3010 100 NRH 3012 100 NRV 3012 220M 220M 220M 10 100M 10 10 10 100M 4R7M Inductance μH〕〔 Inductance μH〕〔 Inductance μH〕〔 4R7M 4R7M 2R2M 2R2M 2R2M Inductance μH〕〔 100M 2R2M 1 1R0N 1 1 1R0N 1 FERRITE PRODUCTS 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 NRS 5012 100 100 NRS 5014 100 NRS 5020 100 NRS 6010 200M 10 Inductance μH〕〔 Inductance μH〕〔 Inductance μH〕〔 4R7M 4R7M 4R7M Inductance μH〕〔 100M 10 10 100M 10 100M 4R7M 2R2M 2R2N 2R2N 1 1R0N 1 1R2N 1 1R0N 1 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 0.1 10 100 1,000 10,000 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔 DC Bias mA〕〔＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound05_e-01 1 131 ■ PACKAGING ①Minimum Quantity Type NRH 2410 NR 3010/NRH 3010 NR 3012/NRH3012/NRV3012 NR 3015 NR 4010 NR 4012 NR 4018 NRG4026 NRS5012 NRS5014 NRS5020 NR 5040 NRS6010 NR 6012 NR 6020 NR 6028 NR 6045 NR 8040 Standard Quantity [pcs] Tape ＆ Reel 2500 20 00 2000 20 00 50 00 4500 3500 2000 1000 1000 800 1500 1000 10 00 2500 20 00 1500 10 00 Type NR 4010 NR 4012 NR 4018 NRG 4026 NRS 5012 NRS 5014 NRS 5020 5.25±0.1 5.25±0.1 （0.207±0.004） 0.207±0.004）（ 4.3±0.1 4.3±0.1 （0.169±0.004） 0.169±0.004）（ Chip cavity A B Insertion pitch F Tape thickness T K 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 2.1±0.1 （0.083±0.004） 0.3±0.05 3.1±0.1 （0.012±0.002） 0.122±0.004）（ 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 2.3±0.1 （0.091±0.004） 4.2±0.1 （0.165±0.004） 1.4±0.1 （0.055±0.004） 1.6±0.1 （0.063±0.004） 8.0±0.1 （0.315±0.004） 5.15±0.1 5.15±0.1 NR 5040 （0.203±0.004） 0.203±0.004）（ NRS 6010 NR 6012 NR 6020 NR 6028 NR 6045 6.3±0.1 6.3±0.1 （0.248±0.004） 0.248±0.004）（ 0.4±0.1 （0.016±0.004） 2.3±0.1 （0.090±0.004） ②Tape Material 3.1±0.1 （0.122±0.004） 4.7±0.1 （0.185±0.004） Unit : mm (inch) ◦Embossed tape 16mm wide (0.63 inches wide) 2.0±0.1 （0.079±0.004） 4.0±0.1 （0.157±0.004） φ1.5±0.1 （0.059±0.004） F CHIP cavity K 1.75±0.1 （0.069±0.004） T 16.0±0.3 （0.630±0.012） A 7.5±0.1 （0.295±0.004） B Electrode bottom view）（ ③Taping dimensions ◦Embossed tape 8mm wide (0.315 inches wide) （0.059ー0 ＋0.1 φ1.5ー0 Type NR 8040 Chip cavity A B Insertion pitch F Tape thickness T K 0.5±0.1 (0.020±0.004) 4.5±0.1 (0.177±0.004) Unit : mm (inch) CHIP cavity ）＋0.004 1.75±0.1 K （0.069±0.004） T 3.5±0.1 （0.138±0.004） 8.0±0.2 （0.315±0.008） 8.3±0.1 12.0±0.1 8.3±0.1 (0.327±0.004) (0.327±0.004) (0.472±0.004) A B ④Leader and Blank portion ◦NR, NRH, NRS, NRG, NRV Electrode bottom view）（ Blank portions Chip cavity Blank portions Leader F 2.0±0.05 4.0±0.1 （0.079±0.002）（0.157±0.004） Type NRH 2410 NR 3010 NRH 3010 Chip cavity A B 2.6±0.1 2.6±0.1 （0.102±0.004） 0.102±0.004）（ Insertion pitch F Tape thickness T K 0.25±0.05 1.3±0.1 （0.009±0.002） 0.051±0.004）（ 160mm or more (6.3 inches or more) 100mm or more (3.94 inches or more) 400mm or more (15.8 inches or more) 1.4±0.1 （0.055±0.004） 4.0±0.1 NR 3012 3.2±0.1 3.2±0.1 （0.157±0.004） 0.3±0.05 1.6±0.1 NRH 3012 （0.126±0.004） 0.126±0.004）（（0.012±0.002） 0.063±0.004）（ NRV3012 NR 3015 1.9±0.1 （0.075±0.004） Unit : mm (inch) Direction of tape feed ◦Embossed tape 12mm wide (0.47 inches wide) ＋0.1 φ1.5ー0 ＋0.004 （0.059ー0 ） CHIP cavity 1.75±0.1 K （0.069±0.004） T 5.5±0.1 （0.217±0.004） 12.0±0.3 （0.472±0.012） A B F 2.0±0.1 4.0±0.1 （0.079±0.004）（0.157±0.004） Electrode bottom view）（＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0405_pack-P1 1 wound0405_pack_e-01 ■ PACKAGING ⑤Reel size W 2±0.5 φ13±0.5 2.5 or less （0.098inches or less） Reel size (Reference values) φd Type NRH2410 NR 3010 NRH 3010 NR 3012 NRH 3012 NRV 3012 NR 3015 NRS 5012 NRS 5014 NRS 5020 NRS 6010 NR 6 012 φD W 180±0.5 （7.087±0.019） 60±1.0 （2.36±0.04） 10.0±1.5 （0.394±0.059） 180±3.0 （7.087±0.118） 60±2.0 （2.36±0.08） 14.0±1.5 （0.551±0.059） Unit : mm (inch) W 2±0.5 φ13±0.5 t Type φD Reel size (Reference values) φd t (max.) NR 4010 NR 4012 NR 4018 NRG 4026 NR 5040 330±3.0 80±2.0 （12.99±0.118）（3.15±0.078） NR 6 020 NR 6 028 NR 6 045 NR 8040 18.5 （0.72） 13.5±1.0 （0.531±0.04） 22.5 （0.89） 17.5±1.0 （0.689±0.04） Unit : mm (inch) ⑥Top Tape Strength The top tape requires a peel-off force of 0.1 to 1.3N in the direction of the arrow as illustrated below. ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0405_pack_e-01 φD W φd φD φd 1 wound0405_pack-P2 ■ RELIABILITY DATA 1. Operating Temperature Range BRC1608, BRL2012, BRC2016, BRC2518, ー25∼＋105℃ BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, ー25∼＋120℃ NRH24/30, NRS50/60 Type NR10050 Type ー25∼＋105℃ 【Test Method and Remarks】 Including self-generated heat 2. Storage Temperature Range BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, ー40∼＋85℃ NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : 0 to 40℃ for the product with taping. NR10050 Type : 0∼40℃ for the product with taping. 3. Rated current BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Within the speciﬁed tolerance NRH24/30, NRS50/60 Type NR10050 Type 4. Inductance BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Within the speciﬁed tolerance NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : LCR Meter : HP 4285A or equivalent, Measuring frequency : Speciﬁed frequency NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : LCR Meter : HP 4285A or equivalent, 100KHz, 1V NR10050 Type : LCR Meter : HP 4263A or equivalent, 100KHz, 1V 5. DC Resistance BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Within the speciﬁed tolerance NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 DC ohmmeter : HIOKI 3227 or equivalent 6. Self resonance frequency BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Within the speciﬁcation NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : Inpedance analyzer/material analyzer : HP4291A or equivalent HP4191A, 4192A or equivalent 7. Temperature characteristic BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type BRL2012, BRC2016, BRL2518, BRL3225, BRC2518, BRFL2518 Inductance change : Within ±15% BRC1608 Inductance change : Within ±20% NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type Inductance change : Within ±20% NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : Measurement of inductance shall be taken at temperature range within −25℃∼＋85℃. With reference to inductance value at ＋20℃., change rate shall be calculated. Change of maximum inductance deviation in step 1 to 5 Temperature at step 1 Temperature at step 2 Temperature at step 3 Temperature at step 4 Temperature at step 5 20℃ Minimum operating temperature 20℃ (Standard temperature) Maximum oparating temperature 20℃ ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli-RP1 1 wound0407_reli_e-01 ■ RELIABILITY DATA 8. Resistance to ﬂexure of substrate BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type No damage. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : The test samples shall be soldered to the test board by the reﬂow. As illustrated below, apply force in the direction of the arrow indicating until deﬂection of the test board reaches to 2 mm. Force Rod 20 10 Test board size : 100×40×1.0 R230 Test board material : glass epoxy-resin Solder cream thickness : 0.12 (BR Series) Board 0.10 (NR30/40, NRV30, NRH24/30,NRG40) Test Sample R5 0.15 (NR50/60/80, NRS50/60) 45±2mm 45±2mm Land dimension BRC1608）（ 0.9 0.55 0.8 0.55 Land dimension BRL2012）（ Land dimension BRL3225）（ 2.7 1.0 1.6 1.0 Land dimension NR30, NRH30, NRV30）（ 2.7 0.8 1.4 0.8 Land dimension NR60, NRS60）（ 5.7 1.6 3.1 1.6 Land dimension NR, NRS50）（ 4.0 1.5 2.1 1.5 1.4 0.65 0.9 0.65 Land dimension ＢＣ2016）（Ｒ 1.8 0.7 0.8 0.7 Land dimension BRL2518,BRC2518,BRFL2518） Land dimension NRH24）（（ 1.95 0.65 1.5 0.65 0.7 0.75 0.7 2.0 Land dimension NR40, NRG40）（ 3.7 1.2 1.6 1.2 Land dimension NR80）（ 7.5 1.8 3.8 1.8 Printed board thickness : 1.0mm Unit : mm 9. Insulation resistance : between wires BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 10. Insulation resistance : between wire and core BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 11. Withstanding voltage : between wires and core BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 12. Adhesion of terminal electrode BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Shall not come off PC board. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : The test samples shall be soldered to the test board by the reﬂow. ・ plied force Ap : 10N to X and Y directions. ・ Duration : 5s. 10N, 5s ・ Solder cream thickness : 0.15mm. BRC1608, NR10050 Type : ・ Applied force : 5N to X and Y directions. ・ ration Du : 5s. 13. Resistance to vibration BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : The test samples shall be soldered to the test board by the reﬂow. Then it shall be submitted to below test conditions. Frequency Range Total Amplitude Sweeping Method Time 10∼55Hz 1.5mm (May not exceed acceleration 196m/s2) 10Hz to 55Hz to 10Hz for 1min. X Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2hrs of recovery under the standard condition sfter the test, followed by the measurement within 48hrs. ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli_e-01 1 wound0407_reli-RP2 ■ RELIABILITY DATA 14. Solderability BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, At least 90％ of surface of terminal electrode is covered by new solder. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050Type : The test samples shall be dipped in ﬂux, and then immersed in molten solder as shown in below table. Flux : Methanol solution containing rosin 25%. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : Solder Temperature Time 245±5℃ 5±1.0 sec. BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Solder Temperature Time 245±5℃ 5±0.5 sec. ※Immersion depth : All sides of mounting terminal shall be immersed. 15. Resistance to soldering heat BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : 0 3 times of reﬂow oven at 230℃ MIN. for 40sec. with peak temperature at 260＋5 ℃ for 5sec. ー : NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type The test sample shall be exposed to reﬂow oven at 230±5℃ for 40 seconds, with peak temperature at 260±5℃ for 5 seconds, 2 times. NR6020 Type : 0 The test sample shall be exposed to reﬂow oven at 230±5℃ for 40 seconds, with peak temperature at 250＋5 ℃ for 5 seconds, 2 times. ー Test board thickness : 1.0mm Test board material : glass epoxy-resin 16. Thermal shock BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type, NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : The test samples shall be soldered to the test board by the reﬂow. The test samples shall be placed at speciﬁed temperature for speciﬁed time by step 1 to step 4 as shown in below table in sequence. The temperature cycle shall be repeated 100 cycles. Step 1 2 3 4 Conditions of 1 cycle Temperature ( ℃) Duration (min) ー40±3 Room temperature ＋85±2 Room temperature 30±3 Within 3 30±3 Within 3 17. Damp heat BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% No signiﬁcant abnormality in appearance. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Temperature Humidity Time 60±2℃ 90∼95%RH 1000 hours. Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : The test samples shall be soldered to the test board by the reﬂow. The test samples shall be placed in thermostatic oven set at speciﬁed temperature and humidity as shown in below table. Temperature Humidity Time 60±2℃ 90∼95%RH 500±24hour ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli-RP3 1 wound0407_reli_e-01 ■ RELIABILITY DATA 18. Loading under damp heat BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Temperature Humidity Applied current Time 60±2℃ 90∼95％RH Rated current 1000hours. Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : The test samples shall be soldered to the test board by the reﬂow. The test samples shall be placed in thermostatic oven set at speciﬁed temperature and humidity and applied the rated current continuously as shown in below table. Temperature Humidity Applied current Time 60±2℃ 90∼95％RH Rated current 500±2hour 19. Low temperature life test BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type Inductance change : Within ±10% NR30/40/50/60/80, NRV30, NRG40, No signiﬁcant abnormality in appearance. NRH24/30, NRS50/60 Type NR10050 Type 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Temperature Duration ー40±2℃ 1000hours Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type, NR10050 Type : The test samples shall be soldered to the test board by the reﬂow. After that, the test samples shall be placed at test conditions as shown in below table. Temperature Time −40±3℃ 500±24hour 20. High temperature life test BRC1608, BRL2012, BRC2016, BRC2518, Inductance change : Within ±10% BRFL2518, BRL2518, BRL3225 Type No signiﬁcant abnormality in appearance. NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type Inductance change : Within ±10% NR10050 Type No signiﬁcant abnormality in appearance. 【Test Method and Remarks】 BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type : Temperature Duration 85±2℃ 1000hours Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. NR10050 Type : Temperature Time 105±3℃ 500±24hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 21. Loading at high temperature life test BRC1608, BRL2012, BRC2016, BRC2518, BRFL2518, BRL2518, BRL3225 Type NR30/40/50/60/80, NRV30, NRG40, Inductance change : Within ±10% NRH24/30, NRS50/60 Type No signiﬁcant abnormality in appearance. NR10050 Type 【Test Method and Remarks】 NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type : The test samples shall be soldered to the test board by the reﬂow soldering. Temperature Applied current Time 85±2℃ Rated current 500±24hour 22. Standard condition BRC1608, BRL2012, BRC2016, BRC2518, Standard test condition : BRFL2518, BRL2518, BRL3225 Type Unless otherwise speciﬁed, temperature is 20±15％ and 65±20％of relative humidity. When there are question concerning measurement result : In order to provide correlation date, the test shall be condition of 20±2℃ NR30/40/50/60/80, NRV30, NRG40, of temperature, 65±5% relative humidity. NRH24/30, NRS50/60 Type Inductance is in accordance with our measured value. NR10050 Type ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli_e-01 1 wound0407_reli-RP4 ■ PRECAUTIONS SMD Inductors 1. Circuit Design ◆ Operating environment 1. The products described in this speciﬁcation are intended for use in general electronic equipment,(ofﬁce supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high Precautions reliability (trafﬁc systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design ◆Land pattern design 1. Please refer to a recommended land pattern. ◆Land pattern design Technical Surface Mounting consider・Mounting and soldering conditions should be checked beforehand. ations ・A pplicable soldering process to this products is reﬂow soldering only. Precautions 3. Considerations for automatic placement ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. Precautions 2. Mounting and soldering conditions should be checked beforehand. Technical ◆Adjustment of mounting machine consider1. When installing products, care should be taken not to apply distortion stress as it may deform the products. ations 4. Soldering ◆Reﬂow soldering 1. Please contact any of our ofﬁces for a reﬂow soldering, and refer to the recommended condition speciﬁed. 2. This products is reﬂow soldering only. 3. Please do not add any stress to a product until it returns in normal temperature after reﬂow soldering. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after conﬁrming of adhesion, temperature of resistance to soldering heat, soldering etc Precautions sufﬁciently. ◆Recommended conditions for using a soldering iron (NR10050 Type) ・Put the soldering iron on the land-pattern. ・Soldering iron's temperature - Below 350℃ ・Duration - 3 se conds or less ・The soldering iron should not directly touch the inductor. ◆Reﬂow soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. ・BRC1608, BRL2012, BRL2518, BRC2016, BRL3225 Type BRC2518, BRFL2518 Recommended reﬂow condition (Pb free solder) Temperature ℃］［・NR30/40/50/60/80, NRV30, NRG40, NRH24/30, NRS50/60 Type Recommended reﬂow condition (Pb free solder) Temperature ℃］［ 300 200 100 0 150∼180 5sec max Peak ： 250＋5/ー0℃ 30±10sec 230℃ min ・NR10050 Type Recommended reﬂow condition (Pb free solder) Temperature ℃］［ 300 200 100 0 150∼180 5sec max Peak ： 250＋0/ー5℃ 30±10sec 230℃ min Technical considerations 300 200 100 0 150∼180 5sec max Peak ： 260＋0/ー5℃ 30±10sec 230℃ min 90±30sec 90±30sec 90±30sec Ｈeating Time sec】【Ｈeating Time sec】【Ｈeating Time sec】【 5. Cleaning Precautions Technical considerations 6. Handling ◆Handling 1. Keep the product away from all magnets and magnetic objects. ◆Breakaway PC boards (splitting along perforations) 1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deﬂection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations Precautions 1. Please do not give the product any excessive mechanical shocks. 2. Please do not add any shock and power to a product in transportation. ◆Pick-up pressure 1. Please do not push to add any pressure to a winding part. Please do not give any shock and push into a ferrite core exposure part.。 ◆Packing 1. Please avoid accumulation of a packing box as much as possible. ◆Breakaway PC boards (splitting along perforations) 1. Planning pattern conﬁgurations and the position of products should be carefully performed to minimize stress. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. Technical 2. There is a case to be broken by the handling in transportation. considerations ◆Pick-up pressure 1. Damage and a characteristic can vary with an excessive shock or stress. ◆Packing 1. There is a case that transformation and a product of tape are damaged by accumulation of a packing box. 7. Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Precautions ・Recommended conditions Ambient temperature : 0∼40℃ Humidity : Below 70% RH The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. ◆ Cleaning conditions 1. Washing by supersonic waves shall be avoided. ◆ Cleaning conditions 1. If washing by supersonic waves, supersonic waves may cause broken products. Te chnical considerations ＊ T his catalog contains the typical speciﬁcation only due to the limitation of space. When you consider purchase of our products, please check our speciﬁcation. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0407_reli-RP5 1 wound0407_reli_e-01

下载 PDF

NRH2410T150MN 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“NRH2410T150MN”相匹配的价格&库存，您可以联系我们找货

免费人工找货