0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
UP050CH2R7K-B-B

UP050CH2R7K-B-B

  • 厂商:

    TAIYO-YUDEN(太诱)

  • 封装:

    轴向

  • 描述:

    贴片电容(MLCC) 轴向 2.7pF ±10% 50V C0H

  • 数据手册
  • 价格&库存
UP050CH2R7K-B-B 数据手册
Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2016. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or use of our products. Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual specification. ■ Please contact TAIYO YUDEN for further details of product specifications as the individual specification is available. ■ Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our products. ■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC). Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, disaster prevention equipment, medical equipment, highly public information network equipment including, without limitation, telephone exchange, and base station). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment, nuclear control equipment, undersea equipment, military equipment). When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Please note that TAIYO YUDEN shall have no responsibility for any controversies or disputes that may occur in connection with a third party’ s intellectual property rights and other related rights arising from use of our products. TAIYO YUDEN grants no license for such rights. ■ Please note that unless otherwise agreed in writing, the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products. ■ The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter“TAIYO YUDEN’ s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export Administration Regulations” ,“Foreign Exchange and Foreign Trade Control Law”of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 17 AXIAL LEADED CERAMIC CAPACITORS AXIAL LEADED CERAMIC CAPACITORS WAVE WAVE ■PARTS NUMBER U P ① ② 0 2 5 ③ △ B ④ 1 0 4 ⑤ Rated voltage[VDC] 10 16 25 35 50 ②Series name Code P Series name Axial leaded capacitor ③Dimensions(L×φD) Code 025 050 075 A - B ⑦ ⑧ △=Blank space ⑥Capacitance tolerance Code D- J- K- M- Z- ⑦Lead Configurations Code A- B- KF KE NA Dimensions(L×φD)[mm] 2.3×2.0 (Multilayer type) 3.2×2.2 (Multilayer type) 4.2×3.2 (Multilayer type) Capacitance tolerance ±0.5pF ±5% ±10% ±20% +80/-20% Lead Configurations 26mm lead space, ammo pack 52mm lead space, ammo pack 5.0mm pitch formed lead bulk 7.5mm pitch formed lead bulk Axial lead, bulk ⑧Packaging Code B C ④Temperature characteristics Code Temperature characteristics CH 0±60(ppm/℃) △B ±10% B5 ±15% △F +30/-85% ⑤Nominal capacitance Code (example) 010 1R2 103 ※R=Decimal point △ Z ⑨ CERAMIC CAPACITORS ①Rated voltage Code L E T G U K - ⑥ Packaging Ammo Bulk ⑨Internal code Code △△ △Z △J Internal code Multilayer type (Standard) Multilayer type (Low voltage type) Nominal capacitance[pF] 1 1.2 10000 ■STANDARD EXTERNAL DIMENSIONS/MINIMUM QUANTITY Type L φD φd NA Multilayer type 025 Multilayer type 050 Multilayer type 075 2.3max (0.09max) 3.2max (0.126max) 4.2max (0.165max) 2.0max (0.079max) 2.2max (0.087max) 3.2max (0.126max) 0.45±0.05 (0.018±0.002) 0.45±0.05 (0.018±0.002) 0.55±0.05 (0.022±0.002) Minimum quantity[pcs] Bulk KF KE Taping A-/B- 1000 4000 - 5000 1000 3000 - 3000 1000 - 3000 2000 Unit:mm(inch) Bulk Straight NA Taping Straight Formed KF KE A- Pitch:5.0(0.197) Pitch:7.5(0.295) 26(1.024) B- 52(2.047) Unit:mm(inch) c_leaded_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 17 33 ■PARTS NUMBER * All the Axial leaded capacitor of Catalog Lineup are Compliance RoHS. ●Multilayer 025 type Class 1 Parts number Rated voltage[V] CERAMIC CAPACITORS UP025CH010D-[] Z 50 UP025CH1R2D-[] Z 50 UP025CH1R5D-[] Z 50 UP025CH1R8D-[] Z 50 UP025CH2R2D-[] Z 50 UP025CH2R7D-[] Z 50 UP025CH3R3D-[] Z 50 UP025CH3R9D-[] Z 50 UP025CH4R7D-[] Z 50 UP025CH5R6K-[] Z 50 UP025CH6R8K-[] Z 50 UP025CH8R2K-[] Z 50 UP025CH100J-[] Z 50 UP025CH120J-[] Z 50 UP025CH150J-[] Z 50 UP025CH180J-[] Z 50 UP025CH220J-[] Z 50 UP025CH270J-[] Z 50 UP025CH330J-[] Z 50 UP025CH390J-[] Z 50 UP025CH470J-[] Z 50 UP025CH560J-[] Z 50 UP025CH680J-[] Z 50 UP025CH820J-[] Z 50 UP025CH101J-[] Z 50 UP025CH151J-[] Z 50 UP025CH221J-[] Z 50 UP025CH331J-[] Z 50 UP025CH471J-[] Z 50 UP025CH681J-[] Z 50 UP025CH102J-[] Z 50 ・[] Please specify the lead configuration code. Temperature characteristics Nominal capacitance[pF] Capacitance tolerance Q CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 150 220 330 470 680 1 000 ±0.5pF ±0.5pF ±0.5pF ±0.5pF ±0.5pF ±0.5pF ±0.5pF ±0.5pF ±0.5pF ±10% ±10% ±10% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧400+20C Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Temperature characteristics Nominal capacitance[pF] Capacitance tolerance tanδ ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% +80/-20% +80/-20% +80/-20% +80/-20% +80/-20% +80/-20% +80/-20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦5.0% tanδ≦5.0% tanδ≦5.0% tanδ≦5.0% tanδ≦5.0% tanδ≦7.5% tanδ≦12.5% tanδ≦7.5% tanδ≦7.5% tanδ≦7.5% tanδ≦7.5% tanδ≦10.0% tanδ≦10.0% tanδ≦17.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% Insulation resistance [MΩ](min.) 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 ●Multilayer 025 type Class 2 Parts number Rated voltage[V] UP025 B101K-[] Z 50 UP025 B121K-[] Z 50 UP025 B151K-[] Z 50 UP025 B181K-[] Z 50 UP025 B221K-[] Z 50 UP025 B271K-[] Z 50 UP025 B331K-[] Z 50 UP025 B391K-[] Z 50 UP025 B471K-[] Z 50 UP025 B561K-[] Z 50 UP025 B681K-[] Z 50 UP025 B821K-[] Z 50 UP025 B102K-[] Z 50 UP025 B122K-[] Z ★ 50 UP025 B152K-[] Z 50 UP025 B222K-[] Z 50 UP025 B332K-[] Z 50 UP025 B472K-[] Z 50 UP025 B682K-[] Z 50 UP025 B103K-[] Z 50 UP025 B153K-[] Z ★ 50 UP025 B223K-[] Z 50 UP025 B333K-[] Z 50 UP025 B473K-[] Z 50 UP025 B683K-[] Z 50 UP025 B104K-[] Z 50 EP025 B224K-[] Z 16 EP025 B474K-[] Z 16 EP025 B105K-[] Z 16 UP025B5105K-[] Z 50 UP025 F103Z-[] Z 50 UP025 F223Z-[] Z 50 UP025 F473Z-[] Z 50 UP025 F104Z-[] Z 50 EP025 F224Z-[] Z ★ 16 EP025 F474Z-[] Z ★ 16 EP025 F105Z-[] Z ★ 16 EP025 B122M-[] J ★ 16 EP025 B152M-[] J ★ 16 EP025 B182M-[] J ★ 16 EP025 B222M-[] J ★ 16 EP025 B272M-[] J ★ 16 EP025 B332M-[] J ★ 16 EP025 B392M-[] J ★ 16 EP025 B472M-[] J ★ 16 EP025 B562M-[] J ★ 16 EP025 B682M-[] J ★ 16 EP025 B822M-[] J ★ 16 ・[] Please specify the lead configuration code. ★ : Option B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B5 F F F F F F F B B B B B B B B B B B 100 120 150 180 220 270 330 390 470 560 680 820 1 000 1 200 1 500 2 200 3 300 4 700 6 800 10 000 15 000 22 000 33 000 47 000 68 000 100 000 220 000 470 000 1 000 000 1 000 000 10 000 22 000 47 000 100 000 220 000 470 000 1 000 000 1 200 1 500 1 800 2 200 2 700 3 300 3 900 4 700 5 600 6 800 8 200 Insulation resistance [MΩ](min.) 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 1,000 1,000 1,000 500 200 100 100 1,000 1,000 1,000 1,000 500 500 250 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 c_leaded_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 34 17 ■PARTS NUMBER Parts number * All the Axial leaded capacitor of Catalog Lineup are Compliance RoHS. Rated voltage[V] EP025 B103M-[] J ★ 16 EP025 B123M-[] J ★ 16 EP025 B153M-[] J ★ 16 EP025 B183M-[] J ★ 16 EP025 B223M-[] J ★ 16 TP025 F103Z-[] J ★ 25 TP025 F223Z-[] J ★ 25 TP025 F473Z-[] J ★ 25 ・[] Please specify the lead configuration code. ★ : Option Temperature characteristics B B B B B F F F Nominal capacitance[pF] 10 12 15 18 22 10 22 47 000 000 000 000 000 000 000 000 Capacitance tolerance tanδ ±20% ±20% ±20% ±20% ±20% +80/-20% +80/-20% +80/-20% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦7.5% tanδ≦7.5% tanδ≦7.5% Insulation resistance [MΩ](min.) 5,000 5,000 5,000 5,000 5,000 1,000 1,000 1,000 ●Multilayer 050 type Class 1 Parts number Rated voltage[V] Temperature characteristics Nominal capacitance[pF] Capacitance tolerance Q CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 1 000 ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% Q≧400+20C Q≧400+20C Q≧400+20C Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Q≧1000 Insulation resistance [MΩ](min.) 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 CERAMIC CAPACITORS UP050CH220J-[] Z 50 UP050CH240J-[] Z ★ 50 UP050CH270J-[] Z 50 UP050CH300J-[] Z ★ 50 UP050CH330J-[] Z 50 UP050CH360J-[] Z ★ 50 UP050CH390J-[] Z 50 UP050CH430J-[] Z ★ 50 UP050CH470J-[] Z 50 UP050CH510J-[] Z ★ 50 UP050CH560J-[] Z ★ 50 UP050CH620J-[] Z ★ 50 UP050CH680J-[] Z 50 UP050CH750J-[] Z ★ 50 UP050CH820J-[] Z ★ 50 UP050CH910J-[] Z ★ 50 UP050CH101J-[] Z 50 UP050CH111J-[] Z ★ 50 UP050CH121J-[] Z ★ 50 UP050CH131J-[] Z ★ 50 UP050CH151J-[] Z 50 UP050CH161J-[] Z ★ 50 UP050CH181J-[] Z ★ 50 UP050CH201J-[] Z ★ 50 UP050CH221J-[] Z 50 UP050CH241J-[] Z ★ 50 UP050CH271J-[] Z ★ 50 UP050CH301J-[] Z ★ 50 UP050CH331J-[] Z 50 UP050CH361J-[] Z ★ 50 UP050CH391J-[] Z ★ 50 UP050CH431J-[] Z ★ 50 UP050CH471J-[] Z 50 UP050CH511J-[] Z ★ 50 UP050CH561J-[] Z ★ 50 UP050CH621J-[] Z ★ 50 UP050CH681J-[] Z 50 UP050CH751J-[] Z ★ 50 UP050CH821J-[] Z ★ 50 UP050CH911J-[] Z ★ 50 UP050CH102J-[] Z 50 ・[] Please specify the lead configuration code. ★ : Option c_leaded_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 17 35 ■PARTS NUMBER * All the Axial leaded capacitor of Catalog Lineup are Compliance RoHS. ●Multilayer 050 type Class 2 Parts number Rated voltage[V] CERAMIC CAPACITORS UP050 B122K-[] Z ★ 50 UP050 B152K-[] Z ★ 50 UP050 B182K-[] Z ★ 50 UP050 B222K-[] Z 50 UP050 B272K-[] Z ★ 50 UP050 B332K-[] Z 50 UP050 B392K-[] Z ★ 50 UP050 B472K-[] Z 50 UP050 B562K-[] Z ★ 50 UP050 B682K-[] Z 50 UP050 B822K-[] Z ★ 50 UP050 B103K-[] Z 50 UP050 B123K-[] Z ★ 50 UP050 B153K-[] Z 50 UP050 B183K-[] Z ★ 50 UP050 B223K-[] Z 50 UP050 B273K-[] Z ★ 50 UP050 B333K-[] Z 50 UP050 B393K-[] Z ★ 50 UP050 B473K-[] Z 50 UP050 B563K-[] Z ★ 50 UP050 B683K-[] Z 50 UP050 B823K-[] Z ★ 50 UP050 B104K-[] Z 50 UP050 B224K-[] Z 50 UP050 B474K-[] Z 50 GP050 B105K-[] Z 35 EP050 B225K-[] Z 16 EP050 B475K-[] Z 16 EP050 B106K-[] Z 16 UP050 F103Z-[] Z 50 UP050 F223Z-[] Z 50 UP050 F473Z-[] Z 50 UP050 F104Z-[] Z 50 UP050 F224Z-[] Z 50 UP050 F474Z-[] Z 50 UP050 F105Z-[] Z 50 EP050 F225Z-[] Z ★ 16 LP050 F475Z-[] Z ★ 10 LP050 F106Z-[] Z ★ 10 ・[] Please specify the lead configuration code. ★ : Option Temperature characteristics B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B F F F F F F F F F F Nominal capacitance[pF] 1 200 1 500 1 800 2 200 2 700 3 300 3 900 4 700 5 600 6 800 8 200 10 000 12 000 15 000 18 000 2 2000 27 000 33 000 39 000 47 000 56 000 68 000 82 000 100 000 220 000 470 000 1 000 000 2 200 000 4 700 000 10 000 000 10 000 22 000 47 000 100 000 220 000 470 000 1 000 000 2 200 000 4 700 000 10 000 000 Capacitance tolerance tanδ ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% +80/-20% +80/-20% +80/-20% +80/-20% +80/-20% +80/-20% +80/-20% +80/-20% +80/-20% +80/-20% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦3.5% tanδ≦5.0% tanδ≦5.0% tanδ≦5.0% tanδ≦5.0% tanδ≦5.0% tanδ≦5.0% tanδ≦5.0% tanδ≦5.0% tanδ≦7.5% tanδ≦12.5% tanδ≦12.5% tanδ≦7.5% tanδ≦7.5% tanδ≦7.5% tanδ≦7.5% tanδ≦10.0% tanδ≦10.0% tanδ≦15.0% tanδ≦15.0% tanδ≦17.5% tanδ≦17.5% Capacitance tolerance tanδ ±10% ±10% ±10% ±10% ±10% ±10% ±10% +80/-20% tanδ≦5.0% tanδ≦7.5% tanδ≦7.5% tanδ≦12.5% tanδ≦12.5% tanδ≦12.5% tanδ≦12.5% tanδ≦17.5% Insulation resistance [MΩ](min.) 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 1,000 1,000 1,000 1,000 1,000 500 200 100 50 20 20 1,000 1,000 1,000 1,000 500 500 250 125 50 25 ●Multilayer 075 type Class 2 Parts number Rated voltage[V] UP075 B105K-[] 50 GP075 B225K-[] 35 GP075 B475K-[] 35 TP075 B106K-[] 25 UP075B5225K-[] 50 UP075B5475K-[] ★ 50 GP075B5106K-[] ★ 35 GP075 F106Z-[] ★ 35 ・[] Please specify the lead configuration code. ★ : Option Temperature characteristics B B B B B5 B5 B5 F Nominal capacitance[pF] 1 000 000 2 200 000 4 700 000 10 000 000 2 200 000 4 700 000 10 000 000 10 000 000 Insulation resistance [MΩ](min.) 100 50 20 20 40 10 10 25 c_leaded_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 36 17 Axial Leaded Ceramic Capacitors ■PACKAGING ①Minimum Quantity Type Lead configuration code Minimum Quantity Bulk A-(1.024 inch wide) B-(2.047 inches wide) Multilayer type (075, 050, 025) NA KE(075) KF(050) KF(025) - 1000 3000 3000 4000 [pcs] Taping 2000(075) 3000(050) 5000(025) - ②Dimensions of Bulk Products ●NA configuration Type φD 2.0max. (0.079max.) 2.2max. (0.087max.) 3.2max. (0.126max.) Multilayer type 025 Multilayer type 050 Multilayer type 075 Dimensions(mm) L φd 2.3max. 0.45±0.05 (0.09max.) (0.018±0.002) 3.2max. 0.45±0.05 (0.126max.) (0.018±0.002) 4.2max. 0.55±0.05 (0.165max.) (0.022±0.002) ℓ 20.0min. (0.787min.) 20.0min. (0.787min.) 20.0min. (0.787min.) Unit:mm(inch) ●KF/KE configuration Type Multilayer type 025 Multilayer type 050 Multilayer type 075 Lead configuration code KF KF KE φD 2.0max. (0.079max.) 2.2max. (0.087max.) 3.2max. (0.126max.) L 2.3max. (0.09max.) 3.2max. (0.126max.) 4.2max. (0.165max.) Dimensions(mm) W 5.0±0.5 (0.197±0.020) 5.0±0.5 (0.197±0.020) 7.5±0.5 (0.295±0.020) φd 0.45±0.05 (0.018±0.002) 0.45±0.05 (0.018±0.002) 0.55±0.05 (0.022±0.002) ℓ 6.5±0.5 (0.256±0.020) 6.5±0.5 (0.256±0.020) 6.5±0.5 (0.256±0.020) Unit:mm(inch) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_pack_e-E02R01 ③Taping Dimensions ●A-(a:1.024 inch wide)configuration Type Multilayer type 025 Multilayer type 050 Multilayer type 075 Dimensions(mm) φD 2.0max. (0.079max.) 2.2max. (0.087max.) 3.2max. (0.126max.) L 2.3max. (0.09max) 3.2max. (0.126max.) 4.2max. (0.165max.) a b |L1-L2| 26+0.5/-0 (1.024+0.020/-0) 0.8max. (0.031max.) 0.5max. (0.020max.) φd 0.45±0.05 (0.018±0.002) 0.45±0.05 (0.018±0.002) 0.55±0.05 (0.022±0.002) Minimum insertion pitch 5.0 (0.197) 7.5 (0.295) Unit:mm(inch) ●B-(a:2.047 inches wide)configuration Type Multilayer type 025 Multilayer type 050 Multilayer type 075 Dimensions(mm) φD 2.0max. (0.079max.) 2.2max. (0.087max.) 3.2max. (0.126max.) L 2.3max. (0.09max.) 3.2max. (0.126max.) 4.2max. (0.165max.) a b |L1-L2| 52+2/-1 (2.047+0.079/-0.039) 1.2max. (0.047 max.) 1.0max. (0.039max.) φd 0.45±0.05 (0.018±0.002) 0.45±0.05 (0.018±0.002) 0.55±0.05 (0.022±0.002) Minimum insertion pitch 5.0 (0.197) 7.5 (0.295) Unit:mm(inch) ※Radial taping is available for 075 type (Optional) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_pack_e-E02R01 Axial Leaded Ceramic Capacitors ■RELIABILITY DATA 1. Operating Temperature Range Class1(Temperature Compensating) Specified Value Class2(High Dielectric) Multilayer type Multilayer type (Characteristics:B, B5) Multilayer type (Characteristics:F) -25 to +85℃ 2. Storage Temperature Range Class1(Temperature Compensating) Specified Value Class2(High Dielectric) Multilayer type Multilayer type (Characteristics:B, B5) -25 to +85℃ Multilayer type (Characteristics:F) 3. Rate Voltage Class1(Temperature Compensating) Specified Value Class2(High Dielectric) Multilayer type 50VDC Multilayer type (Characteristics:B, B5) 16VDC, 25VDC, 35VDC, 50VDC Multilayer type (Characteristics:F) 10VDC, 16VDC, 25VDC, 35VDC, 50VDC 4. Withstanding Voltage Between terminals Specified Value Test Methods and Remarks No abnorminality Applied voltage Duration Charge/discharge current : Rate Voltage×3(Class 1) : Rate Voltage×2.5(Class 2) : 1 to 5 sec. : 50mA max.(Class 1,2) Between terminals and body Specified Value No abnorminality Test Methods and Remarks Metal globule method Applied voltage Duration Charge/Discharge current : Rate Voltage×2.5 : 1 to 5 sec. : 50mA max. 5.Insulation Resistance Class1(Temperature Compensating) Specified Value Class2(High Dielectric) Multilayer type 10000MΩ min. Multilayer type (Characteristics:B, B5) Rate voltage : 16VDC 1200pF~22000pF(Item△J) 220000pF 470000pF 1000000pF 2200000pF 4700000pF 10000000pF Rate voltage : 25VDC 10000000pF Rate voltage : 35VDC 1000000pF 2200000pF 4700000pF 10000000pF Rate voltage : 50VDC 100pF~39000pF 47000pF~100000pF 220000pF 470000pF 1000000pF 2200000pF : : : : : : : 5000MΩ min 500MΩ min 200MΩ min 100MΩ min 50MΩ min 20MΩ min 20MΩ min : 20MΩ min : : : : 100MΩ min 50MΩ min 20MΩ min 10MΩ min : : : : : : 5000MΩ min 1000MΩ min 500MΩ min 200MΩ min 100MΩ min 40MΩ min ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 4700000pF Rate voltage : 10VDC 4700000pF 10000000pF Rate voltage : 16VDC 220000pF 470000pF 1000000pF 2200000pF Rate voltage : 25VDC 10000pF~47000pF(Item△J) Rate voltage : 35VDC 10000000pF Rate voltage : 50VDC 10000pF~100000pF 220000pF~470000pF 1000000pF Multilayer type (Characteristics:F) Test Methods and Remarks Applied voltage Duration : 10MΩ min : 50MΩ min : 25MΩ min : : : : 500MΩ min 500MΩ min 250MΩ min 125MΩ min : 1000MΩ min : 25MΩ min : 1000MΩ min : 500MΩ min : 250MΩ min : Rate voltage : 60±5 sec. 6.Capacitance Class1(Temperature Compensating) Specified Value Class2(High Dielectric) Measuring frequency Test Methods and Remarks Measuring voltage Bias application : : : : : : : : : Multilayer type ±0.5pF ±5% ±10% Multilayer type (Characteristics:B, B5) ±10%, ±20%(Item△J) Multilayer type (Characteristics:F) +80/-20% 1MHz±10% 1kHz±10% 1kHz±10% 120Hz±10% 1.0±0.5Vrms 1.0±0.2Vrms 1.0±0.2Vrms 0.5±0.1Vrms None (Class1 (Class1 (Class2 (Class2 (Class1 (Class1 (Class2 (Class2 : C≦1000pF) : C>1000pF) : C≦10μF) : C>10μF) : C≦1000pF) : C>1000pF) : C≦10μF) : C>10μF) 7.Q or Tangent of Loss Angle(tanδ) Class1(Temperature Compensating) Multilayer type Multilayer type (Characteristics:B, B5) Specified Value Class2(High Dielectric) Multilayer type (Characteristics:F) 30pF or under : Q≧400+20C 33pF or over : Q≧1000 C:Nominal Capacitance[pF] Rate voltage : 16VDC 1200pF~22000pF(Item△J) 220000pF~470000pF 1000000pF~2200000pF 4700000pF~10000000pF Rate voltage : 25VDC 10000000pF Rate voltage : 35VDC 1000000pF 2200000pF~4700000pF 10000000pF Rate voltage : 50VDC 100pF~39000pF 47000pF~1000000pF (1000000pF/B5 2200000pF~4700000pF Rate voltage : 10VDC 4700000pF~10000000pF Rate voltage : 16VDC 220000pF 470000pF 1000000pF 2200000pF Rate voltage : 25VDC 10000pF~47000pF(Item△J) Rate voltage : 35VDC : : : : 3.5% max 5.0% max 7.5% max 12.5% max : 12.5% max : 5.0% max : 7.5% max : 12.5% max : : : : 3.5% max 5.0% max 12.5% max) 12.5% max : 17.5% max : : : : 10.0% 10.0% 17.5% 15.0% max max max max : 7.5% max ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 Measuring frequency Test Methods and Remarks Measuring voltage Bias application : : : : : : : : : 1MHz±10% 1kHz±10% 1kHz±10% 120Hz±10% 1.0±0.5Vrms 1.0±0.2Vrms 1.0±0.2Vrms 0.5±0.1Vrms None (Class1 (Class1 (Class2 (Class2 (Class1 (Class1 (Class2 (Class2 10000000pF Rate voltage : 50VDC 10000pF~100000pF 220000pF~470000pF 1000000pF : C≦1000pF) : C>1000pF) : C≦10μF) : C>10μF) : C≦1000pF) : C>1000pF) : C≦10μF) : C>10μF) : 17.5% max : 7.5% max : 10.0% max : 15.0% max 8.Capacitance:Change due to Temperature or Rate of Capacitance Change When voltage is not applied Class1(Temperature Compensating) Specified Value Class2(High Dielectric) Test Methods and Remarks Multilayer type CH : 0±60 SL : -350~+1000 [ppm/℃] Multilayer type (Characteristics:B, B5) ±10%(B5 : ±15%) Multilayer type +30/-85 % (Characteristics:F) Measurement of capacitance at 20℃ and 85℃, -25℃ shall be made to calculate temperature characteristic by the following equation. (Class 1) (C85-C20) ×106(ppm/℃) C20×△T Change of maximum capacitance deviation in step 1 to 5(Class2) Step Temperature(℃) 1 20 2 -25 3 20(Reference temperature) 4 85 5 20 ※In the B5 characteristics is, the Temperatures of step 1,3, and 5 are 25℃. 9.Terminal Strength Tensile Class1(Temperature Compensating) Specified Value Class2(High Dielectric) Test Methods and Remarks Multilayer type Multilayer type (Characteristics:B, B5) No abnomalities, such as cuts or looseness of terminals. Multilayer type (Characteristics:F) Apply the stated tensile force progressively in the direction to draw terminal. Nominal wire diameter[mm] Tensile force[N] Duration[s] 0.45・0.55 19.6 5 Torsional Class1(Temperature Compensating) Specified Value Class2(High Dielectric) Test Methods and Remarks Multilayer type Multilayer type (Characteristics:B, B5) No abnomalities, such as cuts or looseness of terminals. Multilayer type (Characteristics:F) Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 5 sec. Then second bend in the opposite direction shall be made. Number of bends : 2 times Nominal wire diameter[mm] Bending force[N] Mass weight[kg] 0.45・0.55 2.45 0.25 10.Resistance to Vibration Specified Value Class1(Temperature Compensating) Multilayer type Appearance : No significant abnomality Withstanding Voltage : No abnomality ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 Capacitance : 4.7pF or under 5.6pF~8.2pF 10pF or over Q: 30pF or under 33pF or over Insulation resistance C : Nominal Capacitance [pF] Multilayer type (Characteristics:B, B5) Class2(High Dielectric) Multilayer type (Characteristics:F) : Within ±0.5pF : Within±10% : Within±5% : Q≧400+20C : Q≧1000 : 10000MΩ min Appearance : No significant abnomality Withstanding Voltage : No abnomality Rate Voltage : 16VDC Capacitance 1200pF~22000pF(Item△J) : 220000pF~10000000pF : tanδ : 1200pF~22000pF(Item△J) : 220000pF~470000pF : 1000000pF~2200000pF : 4700000pF~10000000pF : Insulation Resistance : 1200pF~22000pF(Item△J) : 220000pF : 470000pF : 1000000pF : 2200000pF : 4700000pF~10000000pF : Rate Voltage : 25VDC Capacitance : Within ±10% tanδ : 10000000pF : Insulation Resistance : 10000000pF : Rate Voltage : 35VDC Capacitance : Within ±10% tanδ : 1000000pF : 2200000pF~4700000pF : 10000000pF : Insulation Resistance : 1000000pF : 2200000pF : 4700000pF : 10000000pF : Rate Voltage : 50VDC Capacitance : Within ±10% tanδ : 100pF~39000pF : 47000pF~1000000pF : (1000000pF/B5 : 2200000pF~4700000pF : Insulation Resistance : 100pF~39000pF : 47000pF~100000pF : 220000pF : 470000pF : 1000000pF : 2200000pF : 4700000pF : Appearance : No significant abnomality Withstanding Voltage : No abnomality Rate Voltage : 10VDC Capacitance tanδ : 4700000pF~10000000pF Insulation Resistance : 4700000pF 10000000pF Rate Voltage : 16VDC Within ±20% Within ±10% 3.5% max 5.0% max 7.5% max 12.5% max 5000MΩ min 500MΩ min 200MΩ min 100MΩ min 50MΩ min 20MΩ min 12.5% max 20MΩ min 5.0% max 7.5% max 12.5% max 100MΩ min 50MΩ min 20MΩ min 10MΩ min 3.5% max 5.0% max 12.5% max) 12.5% max 5000MΩ min 1000MΩ min 500MΩ min 200MΩ min 100MΩ min 40MΩ min 10MΩ min : Within +80/-20% : 17.5% max : 50MΩ min : 25MΩ min ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 Capacitance tanδ : 220000pF 470000pF 1000000pF 2200000pF Insulation Resistance : 220000pF 470000pF 1000000pF 2200000pF Rate Voltage : 25VDC Capacitance tanδ : 10000pF~47000pF(Item△J) Insulation Resistance : 10000pF~47000pF(Item△J) Rate Voltage : 35VDC Capacitance tanδ : 10000000pF Insulation Resistance 10000000pF Rate Voltage : 50VDC Capacitance tanδ : 10000pF~100000pF 220000pF~470000pF 1000000pF Insulation Resistance : 10000pF~100000pF 220000pF~470000pF 1000000pF Test Methods and Remarks : Within +80/-20% : : : : 10.0% 10.0% 17.5% 15.0% max max max max : : : : 500MΩ min 500MΩ min 250MΩ min 125MΩ min : Within +80/-20% : 7.5% max : 1000MΩ min : Within +80/-20% : 17.5% max : 25MΩ min : Within +80/-20% : 7.5% max : 10.0% max : 15.0% max : 1000MΩ min : 500MΩ min : 250MΩ min According to JIS C 5101-1 Vibration type :A Directions : 2 hrs each in X, Y and Z directions Total : 6 hrs Frequency range : 10 to 55 to 10Hz(1min) Amplitude : 1.5mm Mountin method : Soldering onto the PC board 11.Free Fall Appearance:No significant abnomality Withstanding Voltage:No abnomality Class1(Temperature Compensating) Multilayer type Specified Value Class2(High Dielectric) Multilayer type (Characteristics:B, B5) Capacitance 4.7pF or under 5.6pF~8.2pF 10pF or over Q: 30pF or under 33pF or over Insulation resistance C : Nominal Capacitance [pF] : Within ±0.5pF : Within ±10% : Within ±5% : Q≧400+20C : Q≧1000 : 10000MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Rate Voltage:16VDC Capacitance: 1200pF~22000pF(Item△J) :Within ±20% 220000pF~10000000pF :Within ±10% tanδ: 1200pF~22000pF(Item△J) :3.5% max 220000pF~470000pF :5.0% max 1000000pF~2200000pF :7.5% max 4700000pF~10000000pF :12.5% max Insulation resistance: 1200pF~22000pF(Item△J) :5000MΩ min 220000pF :500MΩ min 470000pF :200MΩ min 1000000pF :100MΩ min ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 2200000pF 4700000pF~10000000pF Rate Voltage:25VDC Capacitance:Within ±10% tanδ: 10000000pF Insulation resistance: 10000000pF Rate Voltage:35VDC Capacitance:Within ±10% tanδ: 1000000pF 2200000pF~4700000pF 10000000pF Insulation resistance: 1000000pF 2200000pF 4700000pF 10000000pF Rate Voltage:50VDC Capacitance:Within ±10% tanδ: 100pF~39000pF 47000pF~1000000pF (1000000pF/B5 2200000pF~4700000pF Insulation resistance: 100pF~39000pF 47000pF~100000pF 220000pF 470000pF 1000000pF 2200000pF 4700000pF Multilayer type (Characteristics:F) :50MΩ min :20MΩ min :12.5% max :20MΩ min :5.0% max :7.5% max :12.5% max :100MΩ min :50MΩ min :20MΩ min :10MΩ min :3.5% max :5.0% max :12.5% max) :12.5% max :5000MΩ min :1000MΩ min :500MΩ min :200MΩ min :100MΩ min :40MΩ min :10MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Rate Voltage:10VDC Capacitance :Within +80/-20% tanδ: 4700000pF~10000000pF :17.5% max Insulation resistance: 4700000pF :50MΩ min 10000000pF :25MΩ min Rate Voltage:16VDC Capacitance : Within+80/-20% tanδ: 220000pF :10.0% max 470000pF :10.0% max 1000000pF :17.5% max 2200000pF :15.0% max Insulation resistance: 220000pF :500MΩ min 470000pF :500MΩ min 1000000pF :250MΩ min 2200000pF :125MΩ min Rate Voltage:25VDC Capacitance : Within +80/-20% tanδ: 10000pF~47000pF(Item△J) :7.5% max Insulation resistance: 10000pF~47000pF(Item△J) :1000MΩ min Rate Voltage:35VDC Capacitance : Within +80/-20% tanδ: 10000000pF :17.5% max Insulation resistance: 10000000pF :25MΩ min Rate Voltage:50VDC Capacitance : Within +80/-20% ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 tanδ: 10000pF~100000pF 220000pF~470000pF 1000000pF Insulation resistance: 10000pF~100000pF 220000pF~470000pF 1000000pF Test Methods and Remarks Drop Test Impact material Height Total number of drops : : : : :7.5% max :10.0% max :15.0% max :1000MΩ min :500MΩ min :250MΩ min Free fall Floor 1m 5 times 12.Body Strength Class1(Temperature Compensating) Multilayer type Class2(High Dielectric) Multilayer type (Characteristics:B, B5) Multilayer type (Characteristics:F) Specified Value Applied force Duration Speed Test Methods and Remarks No abnomality such as damage. : 19.6N : 5 sec. : Shall attain to specified force in 2 sec. 0.5R 90° 2.0mm 1.5mm(025type) 13.Solderability Class1(Temperature Compensating) Multilayer type Class2(High Dielectric) Multilayer type (Characteristics:B, B5) Multilayer type (Characteristics:F) Specified Value Test Methods and Remarks Solder temperature Duration At least 75% of lead surface is covered with new solder. : 230±5℃ : 2±0.5 sec.(This test may be applicable after 6 months storage.) 14.Soldering Appearance:No significant abnomality Withstanding Voltage:No abnomality Class1(Temperature Compensating) Multilayer type Capacitance change: 8.2pF or under 10pF or over Q: 30pF or under 33pF or over Insulation resistance C:Nominal Capacitance [pF] :Within ±0.25pF :Within ±2.5% :Q≧400+20C :Q≧1000 :10000MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Specified Value Class2(High Dielectric) Multilayer type (Characteristics:B, B5) Rate Voltage:16VDC Capacitance change: 1200pF~22000pF(Item△J) 220000pF~10000000pF tanδ: 1200pF~22000pF(Item△J) 220000pF~470000pF 1000000pF~2200000pF 4700000pF~10000000pF Insulation resistance: 1200pF~22000pF(Item△J) 220000pF :Within±7.5% :Within±10.0% :3.5% max :5.0% max :7.5% max :12.5% max :5000MΩ min :500MΩ min ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 470000pF :200MΩ min 1000000pF :100MΩ min 2200000pF :50MΩ min 4700000pF~10000000pF :20MΩ min Rate Voltage:25VDC Capacitance change: 10000000pF :Within ±10.0% tanδ: 10000000pF :12.5% max Insulation resistance: 10000000pF :20MΩ min Rate Voltage:35VDC Capacitance change: 1000000pF~10000000pF :Within ±10.0% tanδ: 1000000pF :5.0% max 2200000pF~4700000pF :7.5% max 10000000pF :12.5% max Insulation resistance: 1000000pF :100MΩ min 2200000pF :50MΩ min 4700000pF :20MΩ min 10000000pF :10MΩ min Rate Voltage:50VDC Capacitance change: 100pF~39000pF :Within ±7.5% 47000pF~1000000pF :Within ±10.0% tanδ: 100pF~39000pF :3.5% max 47000pF~1000000pF :5.0% max (1000000pF/B5 :12.5% max) 2200000pF~4700000pF :12.5% max Insulation resistance: 100pF~39000pF :5000MΩ min 47000pF~100000pF :1000MΩ min 220000pF :500MΩ min 470000pF :200MΩ min 1000000pF :100MΩ min 2200000pF :40MΩ min 4700000pF :10MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Multilayer type (Characteristics:F) Rate Voltage:10VDC Capacitance change tanδ: 4700000pF~10000000pF Insulation resistance: 4700000pF 10000000pF Rate Voltage:16VDC Capacitance change tanδ: 220000pF~470000pF 1000000pF 2200000pF Insulation resistance: 220000pF~470000pF 1000000pF 2200000pF Rate Voltage:25VDC Capacitance change tanδ: 10000pF~47000pF(Item△J) Insulation resistance: 10000pF~47000pF(Item△J) Rate Voltage:35VDC Capacitance change tanδ: 10000000pF :Within ±20% :17.5% max :50MΩ min :25MΩ min :Within ±20% :10.0% max :17.5% max :15.0% max :500MΩ min :250MΩ min :125MΩ min :Within ±20% :7.5% max :1000MΩ min :Within ±20% :17.5% max ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 Insulation resistance: 10000000pF Rate Voltage:50VDC Capacitance change: 10000pF~1000000pF tanδ: 10000pF~100000pF 220000pF~470000pF 1000000pF Insulation resistance: 10000pF~100000pF 220000pF~470000pF 1000000pF Test Methods and Remarks Solder temperature Duration Immersed conditions Preconditioning Recovery :7.5% max :10.0% max :15.0% max :1000MΩ min :500MΩ min :250MΩ min 270±5℃ 5±0.5 sec. Inserted into the PC board(with t=1.6mm, hole=1.0mm diameter) 1 hr of preconditioning at 150 +0/-10℃ followed by 48±4 hrs of recovery under the standard condition. : Recovery for the following period under the standard condition after the test. 24±2 hrs(Class 1) 48±4 hrs(Class 2) Multilayer type Multilayer type (Characteristics:B, B5) Multilayer type (Characteristics:F) Specified Value Class2(High Dielectric) Test Methods and Remarks :Within 20.0% : : : : 15.Resistance to Solvent Class1(Temperature Compensating) According to JIS C 5101-1 Type of test Solvent temperature Duration Solvent Type :25MΩ min : : : : No significant abnormality in appearance and legible marking. Method 1 20 to 25℃ 30±5 sec. A in Table 23, Isopropyl alcohol 16.Thermal Shock Appearance:No significant abnomality Withstanding Voltage:No abnomality Class1(Temperature Compensating) Multilayer type Specified Value Class2(High Dielectric) Multilayer type (Characteristics:B, B5) Capacitance change: 8.2pF or under 10pF or over Q: 8.2pF or under 10pF~30pF 33pF or over Insulation resistance C : Nominal Capacitance [pF] :Within ±0.5pF :Within ±5.0% :Q≧200+10C :Q≧275+2.5C :Q≧350 :1000MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Rate voltage:16VDC Capacitance change: 1200pF~22000pF(Item△J) :Within ±12.5% 220000pF~10000000pF :Within ±15.0% tanδ: 1200pF~22000pF(Item△J) :5.0% max 220000pF~470000pF :7.5% max 1000000pF~2200000pF :10.0% max 4700000pF~10000000pF :22.5% max Insulation resistance: 1200pF~22000pF(Item△J) :1000MΩ min 220000pF :125MΩ min 470000pF :50MΩ min 1000000pF :25MΩ min 2200000pF :12.5MΩ min 4700000pF~10000000pF :5MΩ min Rate voltage:25VDC Capacitance change: 10000000pF :Within ±15.0% ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 tanδ: 10000000pF :15.0% max Insulation resistance: 10000000pF :5MΩ min Rate voltage:35VDC Capacitance change: 1000000pF :Within ±15.0% 2200000pF~4700000pF :Within ±15.0% 10000000pF :Within ±15.0% tanδ: 1000000pF :7.5% max 2200000pF~4700000pF :10.0% max 10000000pF :22.5% max Insulation resistance: 1000000pF :50MΩ min 2200000pF :25MΩ min 4700000pF~10000000pF :5MΩ min Rate voltage:50VDC Capacitance change: 100pF~39000pF :Within ±12.5% 47000pF~4700000pF :Within ±15.0% (1000000pF/B5 :Within ±22.5%) tanδ: 100pF~39000pF :5.0% max 47000pF~1000000pF :7.5% max (1000000pF/B5 :Within ±17.5%) 2200000pF~47000000pF :22.5% max Insulation resistance: 100pF~39000pF :1000MΩ min 47000pF~100000pF :500MΩ min 220000pF :250MΩ min 470000pF :100MΩ min 1000000pF :50MΩ min 2200000pF :20MΩ min 4700000pF :5MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Multilayer type (Characteristics:F) Rate voltage:10VDC Capacitance change tanδ: 4700000pF~10000000pF Insulation resistance: 4700000pF 10000000pF Rate voltage:16VDC Capacitance change tanδ: 220000pF~470000pF 1000000pF 2200000pF Insulation resistance: 220000pF 470000pF 1000000pF 2200000pF Rate voltage:25VDC Capacitance change tanδ 10000pF~47000pF(Item△J) Insulation resistance: 10000pF~47000pF(Item△J) Rate voltage:35VDC Capacitance change tanδ: 10000000pF Insulation resistance: 10000000pF Rate voltage:50VDC Capacitance change: :Within ±30.0% :20.0% max :10MΩ min :5MΩ min :Within ±30.0% :15.0% max :22.5% max :17.5% max :100MΩ min :50MΩ min :25MΩ min :25MΩ min :Within ±30% : :12.5% max :500MΩ min :Within ±30.0% :20.0% max :5MΩ min ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 10000pF~1000000pF tanδ: 10000pF~100000pF 220000pF~470000pF 1000000pF Insulation resistance: 10000pF~100000pF 220000pF~470000pF 1000000pF Test Methods and Remarks Conditions for 1 cycle Step Temperature[℃] 1 Room temperature 2 -25+0/-3 3 Room temperature 4 +85+3/-0 5 Room temperature Number of cycles Preconditioning Recovery :Within ±30.0% :12.5% max :15.0% max :17.5% max :500MΩ min :250MΩ min :50MΩ min Duration[min.] Within 3 30±3 Within 3 30±3 Within 3 :5 : 1 hr of preconditioning at 150 +0/-10℃ followed by 48±4 hrs of recovery under the standard condition. : Recovery for the following period under the standard condition after the removal from test chamber. 24±2 hrs( Class 1) 48±4 hrs( Class 2) 17.Damp Heat(steady state) Class1(Temperature Compensating) Multilayer type Specified Value Class2(High Dielectric) Multilayer type (Characteristics:B, B5) Appearance:No significant abnomality Withstanding Voltage:No abnomality Capacitance change: 8.2pF or under :Within ±0.5pF 10pF or over :Within ±5.0% Q: 8.2pF or under :Q≧200+10C 10pF~30pF :Q≧275+2.5C 33pF or over :Q≧350 Insulation resistance :1000MΩ min C : Nominal Capacitance [pF] Appearance:No significant abnomality Withstanding Voltage:No abnomality Rate voltage:16VDC Capacitance change: 1200pF~22000pF(Item△J) 220000pF~10000000pF tanδ: 1200pF~22000pF(Item△J) 220000pF~470000pF 1000000pF~2200000pF 4700000pF~10000000pF Insulation resistance: 1200pF~22000pF(Item△J) 220000pF 470000pF 1000000pF 2200000pF 4700000pF~10000000pF Rate voltage:25VDC Capacitance change: 10000000pF tanδ: 10000000pF Insulation resistance: 10000000pF Rate voltage:35VDC Capacitance change: 1000000pF 2200000pF~4700000pF 10000000pF tanδ: 1000000pF 2200000pF~4700000pF 10000000pF :Within ±12.5% :Within ±15.0% :5.0% max :7.5% max :10.0% max :22.5% max :1000MΩ min :125MΩ min :50MΩ min :25MΩ min :12.5MΩ min :5MΩ min :Within ±15.0% :15.0% max :5MΩ min :Within ±15.0% :Within ±15.0% :Within ±15.0% :10.0% max :10.0% max :22.5% max ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 Insulation resistance: 1000000pF 2200000pF 4700000pF~10000000pF Rate voltage:50VDC Capacitance change: 100pF~39000pF 47000pF~4700000pF (1000000pF/B5 tanδ: 100pF~39000pF 47000pF~1000000pF (1000000/B5 2200000pF~4700000pF Insulation resistance: 100pF~39000pF 47000pF~100000pF 220000pF 470000pF 1000000pF 2200000pF 4700000pF :50MΩ min :25MΩ min :5MΩ min :Within ±12.5% :Within ±15.0% :Within ±22.5%) :5.0% max :7.5% max :17.5% max) :22.5% max :1000MΩ min :500MΩ min :250MΩ min :100MΩ min :50MΩ min :20MΩ min :5MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Multilayer type (Characteristics:F) Test Methods and Remarks Temperature Humidity Duration Preconditioning : : : : Rate voltage:10VDC Capacitance change tanδ: 4700000pF~10000000pF Insulation resistance: 4700000pF 10000000pF Rate voltage:16VDC Capacitance change tanδ: 220000pF~470000pF 1000000pF 2200000pF Insulation resistance: 220000pF 470000pF 1000000pF 2200000pF Rate voltage:25VDC Capacitance change tanδ: 10000pF~47000pF(Item△J) Insulation resistance: 10000pF~47000pF(Item△J) Rate voltage:35VDC Capacitance change tanδ: 10000000pF Insulation resistance: 10000000pF Rate voltage:50VDC Capacitance change: 10000pF~1000000pF tanδ: 10000pF~100000pF 220000pF~470000pF 1000000pF Insulation resistance: 10000pF~100000pF 220000pF~470000pF 1000000pF :Within ±30.0% :20.0% max :10MΩ min :5MΩ min :Within ±30.0% :15.0% max :22.5% max :17.5% max :100MΩ min :50MΩ min :25MΩ min :25MΩ min :Within ±30% :12.5% max :500MΩ min :Within ±30.0% :20.0% max :5MΩ min :Within ±30.0% :12.5% max :15.0% max :17.5% max :500MΩ min :250MΩ min :50MΩ min 40±2℃ 90 to 95 % RH 500hrs+24/-0 hrs 1 hr of preconditioning at 150+0/-10 ℃ followed by 48±4 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 Recovery : 24±2 hrs of recovery under the standard condition after the removal from test chamber. (Class 1) : 1 hr of preconditioning at 150+10/-0 ℃ followed by 48±4 hrs of recovery under the standard condition after the removal from chamber. (Class 2) 18.Loading under Damp Heat Appearance:No significant abnomality Withstanding Voltage:No abnomality Class1(Temperature Compensating) Multilayer type Capacitance change: 8.2pF or under 10pF or over Q: 30pF or under 33pF or over Insulation resistance C : Nominal Capacitance [pF] :Within ±0.75pF :Within ±7.5% :Q≧100+10/3*C :Q≧200 :500MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Specified Value Class2(High Dielectric) Multilayer type (Characteristics:B, B5) Rate voltage:16VDC Capacitance change: 1200pF~22000pF(Item△J) 220000pF~470000pF 1000000pF~10000000pF tanδ: 1200pF~22000pF(Item△J) 220000pF~470000pF 1000000pF~2200000pF 4700000pF~10000000pF Insulation resistance: 1200pF~22000pF(Item△J) 220000pF 470000pF 1000000pF 2200000pF 4700000pF~10000000pF Rate voltage:25VDC Capacitance change: 10000000pF tanδ: 10000000pF Insulation resistance: 10000000pF Rate voltage:35VDC Capacitance change: 1000000pF 2200000pF 4700000pF~10000000pF tanδ: 1000000pF 2200000pF~4700000pF 10000000pF Insulation resistance: 1000000pF 2200000pF 4700000pF~10000000pF Rate voltage:50VDC Capacitance change: 100pF~39000pF 47000pF~1000000pF (1000000pF/B5 2200000pF~4700000pF tanδ: 100pF~39000pF 47000pF~1000000pF (1000000pF/B5 2200000pF~4700000pF Insulation resistance: 100pF~39000pF 47000pF~100000pF :Within ±12.5% :Within ±15.0% :Within ±22.5% :5.0% max :7.5% max :10.0% max :22.5% max :500MΩ min :50MΩ min :25MΩ min :12.5MΩ min :5.0MΩ min :2.5MΩ min :Within ±22.5% :22.5% max :2.5MΩ min :Within ±15.0% :Within ±15.0% :Within ±22.5% :10.0% max :10.0% max :22.5% max :12.5MΩ min :5.0MΩ min :2.5MΩ min :Within :Within :Within :Within ±12.5% ±15.0% ±22.5%) ±22.5% :5.0% max :7.5% max :17.5% max) :22.5% max :500MΩ min :250MΩ min ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 220000pF :125MΩ min 470000pF :25MΩ min 1000000pF :12.5MΩ min 2200000pF :10MΩ min 4700000pF :2.5MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Multilayer type (Characteristics:F) Test Methods and Remarks Temperature Humidity Duration Applied voltage Preconditioning Recovery Rate voltage:10VDC Capacitance change tanδ: 4700000pF~10000000pF Insulation resistance: 4700000pF 10000000pF Rate voltage:16VDC Capacitance change tanδ: 220000pF~470000pF 1000000pF 2200000pF Insulation resistance: 220000pF 470000pF 1000000pF 2200000pF Rate voltage:25VDC Capacitance change tanδ: 10000pF~47000pF(Item△J) Insulation resistance: 10000pF~47000pF(Item△J) Rate voltage:35VDC Capacitance change tanδ: 10000000pF Insulation resistance: 10000000pF Rate voltage:50VDC Capacitance change 10000pF~1000000pF tanδ: 10000pF~100000pF 220000pF~470000pF 1000000pF Insulation resistance: 10000pF~100000pF 220000pF~470000pF 1000000pF :Within ±30.0% :20.0% max :5MΩ min :2.5MΩ min :Within ±30.0% :15.0% max :22.5% max :17.5% max :50MΩ min :25MΩ min :12.5MΩ min :12.5MΩ min :Within ±30.0% :12.5% max :250MΩ min :Within ±30.0% :20.0% max :2.5MΩ min : :Within ±30.0% :12.5% max :15.0% max :17.5% max :250MΩ min :125MΩ min :25MΩ min : 40±2℃ : 90 to 95 % RH : 500 +24/-0 hrs : Rate voltage : 1 hr of preconditioning at 150 +0/-10 ℃ followed by 48±4 hrs of recovery under the standard condition. : 24±2 hrs of recovery under the standard condition after the removal from test cham-ber. (Class 1) : 1 hr of preconditioning at 150+10/-0 ℃ followed by 48±4 hrs of recovery under the standard condition after the removal from chamber. (Class 2) 19.High Temperature Lading Test Appearance:No significant abnomality Withstanding Voltage:No abnomality Specified Value Class1(Temperature Compensating) Multilayer type Capacitance change: 8.2pF or under 10pF or over Q: 8.2pF or under 10pF~30pF 33pF or over Insulation resistance :Within ±0.3pF :Within ±3.0% :Q≧200+10C :Q≧275+2.5C :Q≧350 :1000MΩ min ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 C : Nominal Capacitance [pF] Multilayer type (Characteristics:B, B5) Class2(High Dielectric) Multilayer type (Characteristics:F) Appearance:No significant abnomality Withstanding Voltage:No abnomality Rate voltage:16VDC Capacitance change: 1200pF~22000pF(Item△J) :Within ±12.5% 220000pF~470000pF :Within ±15.0% 1000000pF~10000000pF :Within ±22.5% tanδ: 1200pF~22000pF(Item△J) :5.0% max 220000pF~470000pF :7.5% max 1000000pF~2200000pF :10.0% max 4700000pF~10000000pF :22.5% max Insulation resistance: 1200pF~22000pF(Item△J) :1000MΩ min 220000pF :125MΩ min 470000pF :50MΩ min 1000000pF :25MΩ min 2200000pF :12.5MΩ min 4700000pF~10000000pF : 5.0MΩ min Rate voltage:25VDC Capacitance change: 10000000pF :Within ±22.5% tanδ: 10000000pF :22.5% max Insulation resistance: 10000000pF :5MΩ min Rate voltage:35VDC Capacitance change: 1000000pF :Within ±15.0% 2200000pF :Within ±15.0% 4700000pF~10000000pF :Within ±22.5% tanδ: 1000000pF :10.0% max 2200000pF~4700000pF :10.0% max 10000000pF :22.5% max Insulation resistance: 1000000pF :25MΩ min 2200000pF :25MΩ min 4700000pF~10000000pF :5MΩ min Rate voltage:50VDC Capacitance change: 100pF~39000pF :Within ±12.5% 47000pF~1000000pF :Within ±15.0% (1000000pF/B5 :Within ±22.5%) 2200000pF~4700000pF :Within ±22.5% tanδ: 100pF~39000pF :5.0% max 47000pF~1000000pF :7.5% max (1000000/B5 :17.5% max) 2200000pF~4700000pF :22.5% max Insulation resistance: 100pF~39000pF :1000MΩ min 47000pF~100000pF :500MΩ min 220000pF :250MΩ min 470000pF :100MΩ min 1000000pF :50MΩ min 2200000pF :20MΩ min 4700000pF :5MΩ min Appearance:No significant abnomality Withstanding Voltage:No abnomality Rate voltage:10VDC Capacitance change tanδ: 4700000pF~10000000pF Insulation resistance: 4700000pF 10000000pF Rate voltage:16VDC :Within ±30.0% :20.0% max :10MΩ min :5MΩ min ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 Capacitance change tanδ: 220000pF~470000pF 1000000pF 2200000pF Insulation resistance: 220000pF 470000pF 1000000pF 2200000pF Rate voltage:25VDC Capacitance change tanδ: 10000pF~47000pF(Item△J) Insulation resistance: 10000pF~47000pF(Item△J) Rate voltage:35VDC Capacitance change tanδ: 10000000pF Insulation resistance: 10000000pF Rate voltage:50VDC Capacitance change: 10000pF~1000000pF tanδ: 10000pF~100000pF 220000pF~470000pF 1000000pF Insulation resistance: 10000pF~100000pF 220000pF~470000pF 1000000pF Temperature Duration Applied voltage Test Methods and Remarks Preconditioning Recovery :Within ±30.0% :15.0% max :22.5% max :17.5% max :100MΩ min :50MΩ min :25MΩ min :25MΩ min :Within ±30% :10.0% max :500MΩ min :Within ±30.0% :20.0% max :5MΩ min :Within 30.0% :10.0% max :12.5% max :17.5% max :500MΩ min :250MΩ min :50MΩ min : : : : 85 +3/-0 ℃ 1000 +48/-0 hrs Rate voltage×2 Rate voltage×1.5 Class 2: B,B5 1000000pF(025Type) : B,B5 220000pF~10000000pF(050Type, 075Type) : 1 hr of preconditioning at 150 +10-0 ℃ followed by 48±4 hrs of recovery under the standard condition. : 24±2hrs of recovery under the standard condition after the removal from test chamber. (Class1) : 1 hr of preconditioning at 150+10-0 ℃ followed by 48±4 hrs of recovery under the standard condition after the removal from chamber. (Class 2) Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure.Unless otherwise specified, all the tests are conducted under the "standard condition." Withstanding voltage is also referred to as "voltage proof" under IEC specifications. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_reli_e-E04R01 Precautions on the use of Axial Leaded Ceramic Capacitors ■PRECAUTIONS 1. Circuit Design Precautions ◆Verification of operating environment, electrical rating and performance 1. A malfunction in medical equipment, spacecraft, nuclear reactors, etc. may cause serious harm to human life or have severe social ramifications. As such, any capacitors to be used in such equipment may require higher safety and/or reliability considerations and should be clearly differentiated from components used in general purpose applications. ◆Verification of Rated voltage( DC rated voltage) 1. The operating voltage for capacitors must always be lower than their rated values. If an AC voltage is loaded on a DC voltage, the sum of the two peak voltages should be lower than the rated value of the capacitor chosen. For a circuit where both an AC and a pulse voltage may be present, the sum of their peak voltages should also be lower than the capacitor's rated voltage. ◆Self-generated heat (Verification of Temperature) 1. If the capacitors specified only for DC use are used in AC or pulse circuits, the AC or a pulse current can generate heat inside the capacitor so the self-generated temperature rise should be limited to within 20℃. The surface temperature measured should include this self-temperature rise. Therefore, it is required to limit capacitor surface temperature including self -generated heat should not exceed the maximum operating temperature of +85℃. ◆Operating Environment precautions 1. Capacitors should not be used in the following environments: (1)Environmental conditions to avoid a. exposure to water or salt water. b. exposure to moisture or condensation. c. exposure to corrosive gases (such as hydrogen sulfide, sulfurous acid, chlorine, and ammonia) 1-1. When an AC or a pulse voltage is applied to capacitors specified for DC use, even if the voltage is less than the rated voltage, the AC current or pulse current running through the capacitor will cause the capacitor to self-generate heat because of the loss characteristics. The amount of heat generated depends on the dielectric materials used, capacitance, applied voltage, frequency, voltage waveform, etc. The surface temperature changes due to emitted heat which differs by capacitor shape or mounting method. Please contact Taiyo Yuden with any questions regarding emitted heat levels in your particular application. It is recommended the temperature rise be measured in the actual circuit to be used. 1-2. For capacitors, the voltage and frequency relationship is generally determined by peak voltage at low frequencies, and by self-generated heat at high frequencies. (Refer to the following curve.) Technical considerations Applied voltage Sum of the peak voltage (peak to peak) Self-generated heat limit Difference in self-generated heat relative to capacitance Frequency 2. PCB Design Precautions ◆Design of the capacitor mount 1. When capacitors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not it will cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs. As a result, humidity resistance performance would be lost and may lead to a reduction in insulation resistance and cause a withstand voltage failure. 3. Considerations for automatic insertion Precautions Technical considerations ◆Adjustment Automatic Insertion machines( leaded components) 1. When inserting capacitors in a PC board by auto-insertion machines the impact load imposed on the capacitors should be minimized to prevent the leads from chucking or clinching. 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 2. Our company recommends the method to place the lead with fewer loads that join the product. 4. Soldering ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_prec_e-E02R01 Precautions Technical considerations ◆Selection of Flux 1. When soldering capacitors are on the board, flux should be applied thinly and evenly. 2. Flux used should be with less than or equal to 0.1 wt% (equivalent to Chlorine) of halogenated content. Flux having a strong acidity content should not be applied. 3. When using water-soluble flux, special care should be taken to properly clean the boards. ◆Wave Soldering 1. Temperature, time, amount of solder, etc. are specified in accordance with the following recommended conditions. 2. Do not immerse the entire capacitor in the flux during the soldering operation. Only solder the lead wires on the bottom of the board. ◆Recommended conditions for using a soldering iron: 1. Put the soldering iron on the land-pattern. Soldering iron's temperature - below 350℃ Duration - 3 seconds or less Numbers of times - 1 times The soldering iron should not directly touch the capacitor. ◆Selection of Flux 1. Flux is used to increase solderability in wave soldering, but if too much is applied, a large amount of flux gas may be emitted and may detrimentally affect solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system. 2. With too much halogenated substance (Chlorine, etc.) content is used to activate the flux, an excessive amount of residue after soldering may lead to corrosion of the terminal electrodes or degradation of insulation resistance on the surface of the capacitors. 3. Since the residue of water-soluble flux is easily dissolved by water content in the air, the residue on the surface of capacitors in high humidity conditions may cause a degradation of insulation resistance and therefore affect the reliability of the components. The cleaning methods and the capability of the machines used should also be considered carefully when selecting water-soluble flux. ◆Wave Soldering 1. If capacitors are used beyond the range of the recommended conditions, heat stresses may cause cracks inside the capacitors, and consequently degrade the reliability of the capacitors. 2. When the capacitors are dipped in solder, some soldered parts of the capacitor may melt due to solder heat and cause short-circuits or cracking of the ceramic material. Deterioration of the resin coating may lower insulation resistance and cause a reduction of withstand voltage. ◆Recommended conditions for using a soldering iron: 1. If products are used beyond the range of the recommended conditions, heat stress may deform the products, and consequently degrade the reliability of the products. 5. Cleaning Precautions Technical considerations ◆Board cleaning 1. When cleaning the mounted PC boards, make sure that cleaning conditions are consistent with prescribed usage conditions. 1. The resin material used for the outer coating of capacitors is occasionally a wax substance for moisture resistance which can easily be dissolved by some solutions. So before cleaning, special care should be taken to test the component’s vulnerability to the solutions used. When using water-soluble flux please clean the PCB with purified water sufficiently and dry thoroughly at the end of the process. Insufficient washing or drying could lower the reliability of the capacitors. 6. Post-cleaning-process Precautions ◆Application of resin molding, etc. to the PCB and components. 1. Please contact your local Taiyo Yuden sales office before performing resin coating or molding on mounted capacitors. Please contact your local Taiyo Yuden sales office in case of sealing the capacitor with resin or molding it on mounted capacitors. Please verify that the sealing or molding does not affect on the actual application in quality. Technical considerations 1-1. The thermal expansion and coefficient of contraction of the molded resin are not necessarily matched with those of the capacitor. The capacitors may be exposed to stresses due to thermal expansion and contraction during and after hardening. This may lower the specified characteristics and insulation resistance or cause reduced withstanding voltage by cracking the ceramic or separating the coated resin from the ceramics. 1-2. With some types of mold resins, the resin's decomposition gas or reaction gas may remain inside the resin during the hardening period or while left under normal conditions, cause a deterioration of the capacitor's performance. 1-3. Some mold resins may have poor moisture proofing properties. Please verify the contents of the resins before they are applied. 1-4. Please contact Taiyo Yuden before using if the hardening process temperature of the mold resins is higher than the operating temperature of the capacitors. 7. Handling Precautions Technical considerations ◆Mechanical considerations 1. Be careful not to subject the capacitors to excessive mechanical shocks. Withstanding voltage failure may result. 2. If ceramic capacitors are dropped onto the floor or a hard surface they should not be used. 1. Because the capacitor is made of ceramic, mechanical shocks applied to the board may damage or crack the capacitors. 2. Ceramic capacitors which are dropped onto the floor or a hard surface may develop defects and have a higher risk of failure over time. 8. Storage conditions ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_prec_e-E02R01 Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control temperature and humidity in the storage area. Humidity should especially be kept as low as possible. Recommended conditions: Ambient temperature Below 40 ℃ Humidity Below 70% RH. Products should be used within 6 months after delivery. After the above period, the solderability should be checked before using the capacitors. 2. Capacitors should not be kept in an environment filled with decomposition gases such as sulfurous hydrogen, sulfurous acid, chlorine, ammonia, etc. 3. Capacitors should not be kept in a location where they may be exposed to moisture, condensation or direct sunlight. Technical considerations 1. Under high temperature/high humidity conditions, the decrease in solderability due to the oxidation of terminal electrodes and deterioration of taping and packaging characteristics may be accelerated. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . c_leaded_prec_e-E02R01
UP050CH2R7K-B-B 价格&库存

很抱歉,暂时无法提供与“UP050CH2R7K-B-B”相匹配的价格&库存,您可以联系我们找货

免费人工找货