WYSAAVDX7

21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Wireless LAN Module IEEE802.11b/g/n WYSAAVDX7 Data Report TAIYO YUDEN 1/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Document constituent list Control name General Items Absolute maximum ratings Electrical characteristics Circuit schematic Outline / Appearance Pin Layout Handling Precaution Packaging Specification Control No. HD-AG-A100174 HD-AM-A100174 HD-AE-A100174 HD-MC-A100174 HD-AD-A100174 HD-BA-A100174 HQ-BA-521-A HD-BB-A100174 Document Page 1/4 - 4/4 1/1 1/5 - 5/5 1/1 1/2 - 2/2 1/1 1/1 1/2 - 2/2 Rev. records 21-May-2015> Ver.1.0 Released TAIYO YUDEN 2/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Control No. Control name HD-AG-A100174 (1/4) General Items Scope This specification (“Specification”) applies to the hybrid IC for use Wireless LAN module (“Product”) manufacture by TAIYO YUDEN Co., Ltd. (“TAIYO YUDEN”) 1. 2. 3. 4. User Code: WYSAAVDX7 Function: Radio frequency transfer Module. (IEEE802.11bgn standard conformity) Application: PC peripheral, Handy terminal Structure: Hybrid IC loaded with silicon monolithic and GaAs semiconductor Ability of lead free mounting at customer's assembly (Heat resistance of this Product): Yes Containment of hazardous substance in this Product *This product conforms to RoHS Directive. 5. Outline: Stacking Connector Type 6. Marking: IC ID, FCC ID, Japan ID, MAC address and Lot at label on the bottom side. 7. Features: -IEEE802.11bgn standard conformity -Interface: SDIO -Embedded MPU for reducing loads on host processor -Built-in EEPROM (MAC address) 8. Security: WEP (64/128), TKIP, AES, WPA, WPA2, WAPI 9. Packing: Packaging method: Tray Packaging unit: 90pcs./tray 1080pcs./Box 10. Terminal: Data input-output (20pin Stacking Connector) “Panasonic Electric Works Co., Ltd: AXK820145WG” RF input-output (Antenna) 11. Mount: with M2 screw 12. Notes: a. This Product is not designed for radiation durable and should not be used under the circumstance of radiation. b. The operating conditions of this Product are as shown in this Specification. Please note that TAIYO YUDEN shall not be liable for a failure and/or abnormality which is caused by use under the conditions other than the operating conditions hereof. c. This Product mentioned in this Specification is manufactured for use in consumer products. Before using this Product in any special equipment (such as medical equipment, space equipment, air craft, disaster prevention equipment), where higher safety and reliability are duly required, the applicability and suitability of this Product must be fully evaluated by the customer at its sole risk to ensure correct and safety operation of those special equipments. Also, evaluation of the safety function of this Product even for use in general electronics equipment shall be thoroughly made and when necessary, a protective circuit shall be added at design stage, all at the customer’s sole risk. TAIYO YUDEN 3/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Control No. Control name HD-AG-A100174 (2/4) General Items d. i) You are requested to fully check and confirm by the start of mass production of this Product that (1) no bug, defect or other failure is included in firmware incorporated in this Product (“Incorporated Software”), (2) no bug defect or other failure is caused by installation of this Product with Incorporated Software into customer’s products, and that Incorporated Software fully meets customer’s intended use, although TAIYO YUDEN sufficiently inspects or verifies quality of Incorporated Software. ii) Please note that TAIYO YUDEN is not responsible for any failure arising out of bugs or defects in Incorporated Software. e. Communication between this Product and others might not be established nor maintained depending upon radio environment or operating conditions of this Product and other ISM band at 2.4GHz products. f. This Product operates in the unlicensed ISM band at 2.4GHz. In case this Product is used around the other wireless devices which operate in same frequency band of this Product, there is a possibility that interference occurs between this Product and such other devices. If such interference occurs, please stop the operation of other devices or relocate this Product before using this Product or do not use this Product around the other wireless devices. g. Please evaluate adequately our module incorporated to your products before mass production. h. In some cases, TAIYO YUDEN may use replacements as component parts of Products. Such replacement shall apply only to component part of Products, which TAIYO YUDEN deems it possible to replace or substitute according to (i) Scope provided in this Specification (e.g. Official Standard (Type Approvals etc.)) and (ii) Quality of Products. TAIYO YUDEN also ensures traceability of such replacement on production lot basis. j. Caution for Export Control This Product may be subject to governmental approvals, consents, licenses, authorizations, declarations, filings, and registrations for export or re-export of the Product, required by Japanese Foreign Exchange and Foreign Trade Law(including related laws and regulations) and/or any other country’s applicable laws or regulations related to export control. In case you will export or re-export this Product, you are strongly recommended to check and confirm, before exporting or re-exporting, necessary procedures for export or re-export of this Product which is required by applicable laws and regulations, and if necessary, you have to obtain necessary and appropriate approvals or licenses from governmental authority at your own risk and expense. TAIYO YUDEN 4/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Control No. Control name HD-AG-A100174 (3/4) General Items k. Japan Regulatory Information This product with a specific antenna is a radio system approved for Type Approval. Please follow the instructions below on designing your product. a) Please notify clearly below sentences, on your product or in the product manual. This product has a radio system which was approved as a radio station in a low power data communication system based on the Radio Law and the Telecommunication Business Law. Name of the radio system: 001WWCA1266 b) This module is certified by Type Approval as the device which has SDIO Interface. Please do not use other purposes except that of certified. Please contact TAIYO YUDEN for more details of purposes of this product. c) This product is displayed the following actual indication. 2) 3) 1) 4) 5) 1) 2.4 : Represents radio equipment using the 2.4GHz band. 2) DS : Represents modulation DS-SS system. 3) OF : Represents modulation OFDM system. 4) 4 : Represents estimated interference-causing radius to premises radio stations for RFID. 5) ■ ■ ■ : Indicates that the equipment can use the entire band and is capable of avoiding the band used by RFID systems. This equipment shares a frequency band with a wide range of equipment: e.g. industrial, scientific, and medical equipment such as microwave ovens, premises radio stations (radio stations requiring licenses), and specified low-power radio stations (radio stations not requiring licenses) for RFID used for rectory production lines as well as amateur radio stations (radio stations requiring licenses). 1. Before use, confirm that no premises radio stations and specified low-power radio stations for RFID or amateur radio stations operate in your vicinity. 2. In the event that this equipment causes or halt radio wave emission and contact us at the information indicated below for consultation on interference avoidance measures (e.g., partition installation). 3. Contact us if this equipment causes harmful interference to any specified low-power radio stations for RFID or amateur radio stations or if other problems arise. TAIYO YUDEN 5/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Control No. HD-AG-A100174 (4/4) Control name General Items m. Canada Regulatory Information a) This device complies with Industry Canada licence-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. b) This product is certified as type of the portable device with Industry Canada. To maintain compliance with SAR requirement, please use within specification of this product. Please contact TAIYO YUDEN for more details of this product. c) Please notify certified ID by either one of the following method in your product. -Contains Transmitter module IC : 4389B-WYSAAVDX7 -Contains IC : 4389B-WYSAAVDX7 n. FCC Regulatory Information a) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. b) Please notify certified ID by either one of the following method. -Contains Transmitter Module FCC ID: RYYWYSAAVDX7 -Contains FCC ID: RYYWYSAAVDX7 c) CAUTION: changes or modifications not expressly approved by the party responsible for compliance could void the use’s authority to operate the equipment d) This product is certified as type of the portable device with Industry Canada. To maintain compliance with SAR requirement, please use within specification of this product. Please contact TAIYO YUDEN for more details of this product. TAIYO YUDEN 6/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Control No. HD-AM-A100174 (1/1) Control name Absolute maximum ratings Absolute maximum ratings Item Symbol Rating Min. Typ. Max. Unit Supply voltage 1 VBAT -0.3 6.0 V Supply voltage 2 VIO - 4.0 V Remark Recommendation operating range Item Symbol Rating Unit Min. Typ. Max. VBAT 3.4 5.0 5.5 Supply voltage 2 VIO 1.62/2.97 1.8/3.3 1.98/3.63 V Storage temperature range Tstg -30 25 85 Degrees C Topr -20 25 80 Degrees C Supply voltage 1 Operating temperature range (Shielding case surface temperature) Remark V TAIYO YUDEN 7/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Control No. HD-AE-A100174 (1/5) Control name Electrical characteristics DC Specifications Peak Current / Power consumption The Specification applies for Topr.= 25 degrees C, Supply voltage=Typical voltage (5.0V). RF output power = Typ. No. Parameter Condition Symbol Min Typ Max Unit 1 Normal supply voltage 1 VBAT 3.4 5.0 5.5 V 2 Normal supply voltage 2 VIO 1.98/3.63 V 3 Input Low Voltage VIL -0.3 0.3 x VIO V 4 Input High Voltage VIH 0.8 x VIO VIO + 0.3 V 5 Output Low Voltage VOL - 0.4 V 6 Output High voltage VOH VIO - 0.4 - V 1.627/2.97 1.8/3.3 7 Peak current 1 VBAT Iccp1 400 mA 8 Peak current 2 VIO Iccp2 30 mA 9 Power consumption1 Burst Tx (150Mbps), Duty 2.4% Pc1 439 mW 10 Power consumption2 Continuous Rx (150Mbps) Pc2 552 mW 11 Power consumption3 Burst Tx (72.2Mbps), Duty 4..2% Pc3 443 mW 12 Power consumption4 Continuous Rx (72.2Mbps) Pc4 514 mW 13 Power consumption5 Burst Tx (54Mbps), Duty 25.4% Pc5 502 mW 14 Power consumption6 Continuous Rx (54Mbps) Pc6 503 mW 15 Power consumption7 Burst Tx (11Mbps), Duty 43.3% Pc7 651 mW 16 Power consumption8 Continuous Rx (11Mbps) Pc8 499 mW 17 Power consumption9 Power save mode (DTIM=1, Pc9 - 27 - mW VIO=3.3V Pc11 - 3 - mW VIO=3.3V Beacon interval =100ms) 18 Power consumption11 Deep Sleep TAIYO YUDEN 8/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Control No. HD-AE-A100174 (2/5) Control name Electrical characteristics AC Specifications Power-on timing / External sleep clock Conditio n Parameter 1 Valid Power/ Clock to PDn de-asserted Symbol Min Tpor 300 2 Input SLP_CLK frequency Tf 3 Input SLP_CLK high voltage VIH 0.8 4 Input SLP_CLK low voltage VIL 0.0 5 Input SLP_CLK phase noise requirement PN 6 Input SLP_CLK slew rate limit (10-90%) SR Typ Max Unit Remark ms 32.768 1.8 KHz 1.98 0.25 -125 V V dBc/Hz @100KHz 100 7 Input SLP_CLK duty cycle tolerance DC 20 80 PDn must remain asserted for minimum of Tpor after VBAT, VIO and SLP_CLK are stable. RESETn must be inactive value (asserted high) when PDn is de-asserted (high level). ns % External reset(RESETn), power down(PDn) Parameter Conditio n Symbol Min Typ Max Unit Remark 1 RESETn pulse width Trpw 1 ms Note1 2 PDn pulse width Tppw 300 ms Notes2, 3 1. RESETn should be asserted while VBAT, VIO and SLP_CLK are stable and PDn is de-asserted (high level). 2. PDn should be asserted while VBAT, VIO and SLP_CLK are stable and RESETn is de-asserted (high level). 3. For lowest current consumption, apply all power rails to WYSAAVDX7 during the assertion of PDn pin. TAIYO YUDEN 9/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Control No. HD-AE-A100174 (3/5) Control name Electrical characteristics SDIO Interface Specifications The Specification applies for Topr.= 25degrees C , Supply voltage=Typical voltage(5.0V). Parameter Symbol 1 Input SDIO_CLK Frequency Tf 2 Input SDIO_CLK High Time Tch 3 Input SDIO_CLK Low Time Tcl 4 Input SDIO_CMD, DATA[3:0] Setup time Tsu 5 Input SDIO_CMD, DATA[3:0] Hold time Thd 6 Output SDIO_CMD, DATA[3:0] Delay time 7 Output SDIO_CMD, DATA[3:0] Hold time Condition Min Typ Max Normal 0 - 25 High Speed 0 - 50 Normal 10 - - High Speed 7 - - Normal 10 - - High Speed 7 - - Normal 5 - - High Speed 6 - - Unit MHz ns ns ns Normal 5 - - High Speed 2 - - Tod - - - 7.33 ns Toh High Speed 2.5 - - ns Normal Mode Remark ns Tf SD_CLK Tch HOST > WiFi Tsu Tcl Thd SD_CMD SD_DATA[3:0] WiFi > HOST Tod SD_CMD SD_DATA[3:0] High Speed Mode Tf SD_CLK Tch HOST > WiFi Tsu Tcl Thd SD_CMD SD_DATA[3:0] Toh WiFi > HOST Tod SD_CMD SD_DATA[3:0] TAIYO YUDEN 10/19 21-May.2015 Ver.1.0 TAIYO YUDEN WYSAAVDX7 Control No. HD-AE-A100174 (4/5) Control name Electrical characteristics RF Specifications (WLAN 11n/150Mbps, OFDM) The Specification applies for Ta=25 degrees C, Supply voltage =Typical voltage (5.0V). No Parameter Condition Symbol Min Typ Max . 1 RF frequency range FREQ 2422 2462 2 TX Power Po 9 11 13 1st Side Lobe M1 -20 2nd Side Lobe 3 Spectrum Mask M2 -28 rd 3 Side Lobe M3 -45 4 Symbol clock tolerance Ft -25 25 5 Frequency tolerance Ft -25 25 Rms 6 EVM EVM -28 7 TX Out of band spurious1 30MHz to 1GHz TOS1 -36 8 TX Out of band spurious2 1GHz to 12.75GHz TOS2 -30 9 TX Out of band spurious3 1.8GHz to 1.9GHz 5.15GHz to 5.3GHz TOS3 -47 PER