TSL230RD

r r TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 D High-Resolution Conversion of Light D D D D D D D D Intensity to Frequency With No External Components Programmable Sensitivity and Full-Scale Output Frequency Communicates Directly With a Microcontroller High Irradiance Responsivity . . . 790 Hz/(mW/cm2) Typical at 640 nm Single-Supply Operation . . . 2.7 V to 5.5 V Power-Down Feature . . . 5 mA Typical Nonlinearity Error Typically 0.2% at 100 kHz Stable 200 ppm/°C Temperature Coefficient Low-Profile Lead (Pb) Free and RoHS Compliant Surface-Mount Package PACKAGE D 8-LEAD SOIC (TOP VIEW) S0 1 S1 2 OE 3 GND 4 8 S3 7 S2 6 OUT 5 VDD Description The TSL230RD, TSL230ARD, and TSL230BRD programmable light-to-frequency converters combine a configurable silicon photodiode and a current-to-frequency converter on single monolithic CMOS integrated circuit. The output can be either a pulse train or a square wave (50% duty cycle) with frequency directly proportional to light intensity. Device sensitivity is selectable in three ranges, providing two decades of adjustment. The full-scale output frequency can be scaled by one of four preset values. All inputs and the output are TTL compatible, allowing direct two-way communication with a microcontroller for programming and output interface. The output enable (OE) places the output in the high-impedance state for multiple-unit sharing of a microcontroller input line. The devices are available with absolute output frequency tolerances of ±10% (TSL230BRD), ±15% (TSL230ARD), and ±20% (TSL230RD). They have been temperature compensated for the ultraviolet-to-visible light range of 320 nm to 700 nm and respond over the light range of 320 nm to 1050 nm. The devices are characterized over the temperature range of − 25°C to 70°C. Functional Block Diagram Output Light Photodiode Array Current-to-Frequency Converter OE S0 S1 S2 S3 The LUMENOLOGY r Company Texas Advanced Optoelectronic Solutions Inc. 1001 Klein Road S Suite 300 S Plano, TX 75074 S (972) 673-0759 r www.taosinc.com 1 r Copyright E 2007, TAOS Inc. TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 Terminal Functions TERMINAL NAME GND OE OUT S0, S1 S2, S3 VDD NO. 4 3 6 1, 2 7, 8 5 I O I I TYPE Ground Enable for fO (active low) Scaled-frequency (fO) output Sensitivity-select inputs fO scaling-select inputs Supply voltage DESCRIPTION Selectable Options S1 L L H H S0 L H L H SENSITIVITY Power down 1× 10× 100× S3 L L H H S2 L H L H fO SCALING (divide-by) 1 2 10 100 Available Options DEVICE TSL230RD TSL230ARD TSL230BRD TA − 25°C to 70°C − 25°C to 70°C − 25°C to 70°C PACKAGE − LEADS SOIC−8 SOIC−8 SOIC−8 PACKAGE DESIGNATOR D D D ORDERING NUMBER TSL230RD TSL230ARD TSL230BRD Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Input voltage range, all inputs, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 0.3 V to VDD + 0.3 V Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 40°C to 85°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 40°C to 85°C Solder conditions in accordance with JEDEC J−STD−020A, maximum temperature (see Note 2) . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values are with respect to GND. 2. The device may be hand soldered provided that heat is applied only to the solder pad and no contact is made between the tip of the solder iron and the device lead. The maximum time heat should be applied to the device is 5 seconds. Recommended Operating Conditions MIN Supply voltage, VDD High-level input voltage, VIH Low-level input voltage, VIL Operating free-air temperature range, TA Copyright E 2007, TAOS Inc. NOM 5 MAX 5.5 VDD 0.8 70 UNIT V V V °C 2.7 VDD = 4.5 V to 5.5 V VDD = 4.5 V to 5.5 V 2 0 − 25 r r The LUMENOLOGY r Company 2 www.taosinc.com TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 Electrical Characteristics at TA = 25°C, VDD = 5 V (unless otherwise noted) PARAMETER VOH VOL IIH IIL IDD F.S. kSVS High-level output voltage Low-level output voltage High-level input current Low-level input current Supply current Full-scale frequency (See Note 2) Temperature coefficient of output frequency Supply voltage sensitivity Power-on mode Power-down mode S0=S1=H, S2=S3=L λ ≤ 700 nm (See Note 3) VDD = 5 V ±10% 1.1 ± 200 ± 0.5 2 5 TEST CONDITIONS IOH = − 4 mA IOL = 4 mA MIN 4 TYP 4.5 0.25 0.4 5 5 3 12 MAX UNIT V V μA μA mA μA MHz ppm/°C %/ V NOTES: 3. Full-scale frequency is the maximum operating frequency of the device without saturation. 4. The temperature coefficient of output frequency is measured with constant irradiance as the temperature is varied between −25°C and 70°C. The constant irradiance is sufficiently high that the output frequency is much greater than the dark frequency over the entire temperature range. Operating Characteristics at VDD = 5 V, TA = 25°C, Ee = 126 μW/cm2, λp = 640 nm (unless otherwise noted) PARAMETER TEST CONDITIONS S0 = S1 = H, S2 = S3 = L S1 = H, S0 = S2 = S3 = L fO Output frequency frequency S0 = H, S1 = S2 = S3 = L S0 = S1 = S2 = H, S3 = L S0 = S1 = S3 = H, S2 = L S0 = S1 = S2 = S3 = H fD Re tw Dark frequency Responsivity Output pulse Output pulse duration Nonlinearity (See Notes and 5) (See Notes 4 and 5) Ee = 0, S0 = S1 = H, S2 = S3 = L S0 = S1 = H, S2 = S3 = L S2 = S3 = L S2 or S3 = H fO = 0 MHz to 10 kHz fO = 0 MHz to 100 kHz fO = 0 MHz to 1 MHz 125 1/2fO ± 0.1% ± 0.2% ± 0.5% 100 TSL230RD MIN 80 8 0.8 40 8 0.8 TYP 100 10 1 50 10 1 0.4 0.79 600 125 1/2fO ± 0.1% ± 0.2% ± 0.5% 100 1 pulse of new frequency plus 1 μs 2 periods of new principal frequency plus 1 μs (Note 6) 50 150 50 150 50 150 ns MAX 120 12 1.2 60 12 1.2 10 TSL230ARD MIN 85 8.5 0.85 42.5 8.5 0.85 TYP 100 10 1 50 10 1 0.4 0.79 600 125 1/2fO ± 0.1% ± 0.2% ± 0.5% 100 μs %F.S. MAX 115 11.5 1.15 57.5 11.5 1.15 10 TSL230BRD MIN 90 9 0.9 45 9 0.9 TYP 100 10 1 50 10 1 0.4 0.79 600 MAX 110 11 1 55 11 1.1 10 Hz kHz/ (μW/ cm2) ns s UNIT kHz Recovery from power down Step response to full-scale step input Response time to programming change Response time to output enable (OE) NOTES: 5. Nonlinearity is defined as the deviation of fO from a straight line between zero and full scale, expressed as a percent of full scale. 6. Nonlinearity test condition: S0 = S1 = H, S2 = S3 = L. 7. Principal frequency is the internal oscillator frequency, equivalent to divide-by-1 output selection. The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 3 TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 TYPICAL CHARACTERISTICS OUTPUT FREQUENCY vs IRRADIANCE 1000 VDD = 5 V λp = 640 nm TA = 25°C S2 = S3 = L S0 = H, S1 = H 1.2 PHOTODIODE SPECTRAL RESPONSIVITY Output Frequency (fO − fD) — kHz 100 1.0 Normalized Responsivity 10 0.8 1 0.6 0.1 S0 = L, S1 = H 0.4 0.01 S0 = H, S1 = L 0.2 0.001 0.001 0.01 0.1 1 10 100 1k 10k 100k 1M 0 300 400 500 600 700 800 900 1000 1100 Ee − Irradiance − μW/cm2 λ − Wavelength − nm Figure 1 Figure 2 TEMPERATURE COEFFICIENT OF OUTPUT FREQUENCY vs WAVELENGTH OF INCIDENT LIGHT 7000 6000 5000 4000 3000 2000 1000 0 300 VDD = 5 V 1.2 1 fD — Dark Frequency — Hz VDD = 5 V Ee = 0 S0 = S1 = H S2 = S3 = L 0.8 0.6 0.4 0.2 0 −25 0 25 50 75 Temperature Coefficient of Output Frequency — ppm/5C DARK FREQUENCY vs TEMPERATURE 400 500 600 700 800 900 1000 TA − Temperature − °C λ − Wavelength of Incident Light − nm Figure 3 Figure 4 Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 4 www.taosinc.com TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 TYPICAL CHARACTERISTICS OUTPUT FREQUENCY vs SUPPLY VOLTAGE 1.010 TA = 25°C fO = 100 kHz 1.005 Normalized Output Frequency 1.000 0.995 0.990 0.985 0.980 2.5 3 3.5 4 4.5 5 5.5 VDD − Supply Voltage − V Figure 5 NORMALIZED OUTPUT FREQUENCY vs. ANGULAR DISPLACEMENT 1 fO — Output Frequency — Normalized 0.8 Optical Axis Angular Displacement is Equal for Both Aspects 0 −90 −60 −30 0 30 60 Q − Angular Displacement − ° 90 0.6 0.4 0.2 Figure 6 The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 5 TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 APPLICATION INFORMATION Power-Supply Considerations Power-supply lines must be decoupled by a 0.01-μF to 0.1-μF capacitor with short leads placed close to the TSL230RD device package. A low-noise power supply is required to minimize jitter on output pulses. Device Operational Details The frequency at the output pin (OUT) is given by: fO = fD + (Re) (Ee) where: fO fD Re Ee is the output frequency is the output frequency for dark condition (Ee = 0) is the device responsivity for a given wavelength of light given in kHz/(μW/cm2) is the incident irradiance in μW/cm2 fD is an output frequency resulting from leakage currents. As shown in the equation above, this frequency represents a light-independent term in the total output frequency fO. At very low light levels, this dark frequency can be a significant portion of fO. The dark frequency is temperature dependent. For optimum performance of any given device over the full output range, the value of fD should be measured (in the absence of light) and later subtracted from subsequent light measurement (see Figure 1). Input Interface A low-impedance electrical connection between the device OE pin and the device GND pin is required for improved noise immunity. Output Interface The output of the device is designed to drive a standard TTL or CMOS logic input over short distances. If lines greater than 12 inches are used on the output, a buffer or line driver is recommended. Sensitivity Adjustment Sensitivity is controlled by two logic inputs, S0 and S1. Sensitivity is adjusted using an electronic iris technique — effectively an aperture control — to change the response of the device to a given amount of light. The sensitivity can be set to one of three levels: 1 ×, 10 ×, or 100 ×, providing two decades of adjustment. This allows the responsivity of the device to be optimized to a given light level while preserving the full-scale output-frequency range. Changing of sensitivity also changes the effective photodiode area by the same factor. Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 6 www.taosinc.com TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 APPLICATION INFORMATION Output-Frequency Scaling Output-frequency scaling is controlled by two logic inputs, S2 and S3. Scaling is accomplished on chip by internally connecting the pulse-train output of the converter to a series of frequency dividers. Divided outputs available are divide-by 2, 10, 100, and 1 (no division). Divided outputs are 50 percent-duty-cycle square waves while the direct output (divide-by 1) is a fixed-pulse-width pulse train. Because division of the output frequency is accomplished by counting pulses of the principal (divide-by 1) frequency, the final-output period represents an average of n (where n is 2, 10, or 100) periods of the principal frequency. The output-scaling-counter registers are cleared upon the next pulse of the principal frequency after any transition of the S0, S1, S2, S3, or OE lines. The output goes high upon the next subsequent pulse of the principal frequency, beginning a new valid period. This minimizes the time delay between a change on the input lines and the resulting new output period in the divided output modes. In contrast with the sensitivity adjust, use of the divided outputs lowers both the full-scale frequency and the dark frequency by the selected scale factor. The frequency-scaling function allows the output range to be optimized for a variety of measurement techniques. The divide-by-1 or straight-through output can be used with a frequency counter, pulse accumulator, or high-speed timer (period measurement). The divided-down outputs may be used where only a slower frequency counter is available, such as a low-cost microcontroller, or where period measurement techniques are used. The divide-by-10 and divide-by-100 outputs provide lower frequency ranges for high resolution-period measurement. Measuring the Frequency The choice of interface and measurement technique depends on the desired resolution and data acquisition rate. For maximum data-acquisition rate, period-measurement techniques are used. Using the divide-by-2 output, data can be collected at a rate of twice the output frequency or one data point every microsecond for full-scale output. Period measurement requires the use of a fast reference clock with available resolution directly related to reference-clock rate. Output scaling can be used to increase the resolution for a given clock rate or to maximize resolution as the light input changes. Period measurement is used to measure rapidly varying light levels or to make a very fast measurement of a constant light source. Maximum resolution and accuracy may be obtained using frequency-measurement, pulse-accumulation, or integration techniques. Frequency measurements provide the added benefit of averaging out random or high-frequency variations (jitter) resulting from noise in the light signal or from noise in the power supply. Resolution is limited mainly by available counter registers and allowable measurement time. Frequency measurement is well suited for slowly varying or constant light levels and for reading average light levels over short periods of time. Integration (the accumulation of pulses over a very long period of time) can be used to measure exposure, the amount of light present in an area over a given time period. The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 7 TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 APPLICATION INFORMATION PCB Pad Layout Suggested PCB pad layout guidelines for the D package are shown in Figure 7. 4.65 6.90 1.27 0.50 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. 2.25 Figure 7. Suggested D Package PCB Layout Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 8 www.taosinc.com TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 MECHANICAL DATA This SOIC package consists of an integrated circuit mounted on a lead frame and encapsulated with an electrically nonconductive clear plastic compound. The TSL230RD has a 10 × 10 array of photodiodes with a total size of 0.96 mm by 0.96 mm. The photodiodes are 0.084 mm × 0.084 mm in size and are positioned on 0.096 mm centers. PACKAGE D NOTE B 2.12 + 0.250 3.00 + 0.250 PLASTIC SMALL-OUTLINE TOP VIEW BOTTOM VIEW PIN 1 PIN 1 8 y 0.510 0.330 6 y 1.27 SIDE VIEW j 2.8 TYP CLEAR WINDOW END VIEW 0.50 0.25 455 0.88 TYP TOP OF SENSOR DIE A 1.75 1.35 4.00 3.80 6.20 5.80 5.00 4.80 5.3 MAX DETAIL A 0.25 0.19 Pb NOTES: A. B. C. D. 1.27 0.41 0.25 0.10 All linear dimensions are in millimeters. The center of the 0.96-mm by 0.96-mm photo-active area is referenced to the upper left corner tip of the lead frame (Pin 1). Package is molded with an electrically nonconductive clear plastic compound having an index of refraction of 1.55. This drawing is subject to change without notice. Figure 8. Package D — Plastic Small Outline IC Packaging Configuration The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 9 TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 MECHANICAL DATA SIDE VIEW Ko 2.11 + 0.10 [0.083 + 0.004] 0.292 + 0.013 [0.0115 + 0.0005] TOP VIEW j 1.50 8 + 0.1 [0.315 + 0.004] 4 + 0.1 [0.157 + 0.004] 2 + 0.05 [0.079 + 0.002] 1.75 + 0.10 [0.069 + 0.004] END VIEW B 5.50 + 0.05 [0.217 + 0.002] 12 + 0.3 − 0.1 [0.472 + 0.12 − 0.004] A A B DETAIL A DETAIL B Ao NOTES: A. B. C. D. E. F. 6.45 + 0.10 [0.254 + 0.004] Bo 5.13 + 0.10 [0.202 + 0.004] All linear dimensions are in millimeters [inches]. The dimensions on this drawing are for illustrative purposes only. Dimensions of an actual carrier may vary slightly. Symbols on drawing Ao, Bo, and Ko are defined in ANSI EIA Standard 481−B 2001. Each reel is 178 millimeters in diameter and contains 1000 parts. TAOS packaging tape and reel conform to the requirements of EIA Standard 481−B. This drawing is subject to change without notice. Figure 9. Package D Carrier Tape Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 10 www.taosinc.com TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 MANUFACTURING INFORMATION The Plastic Small Outline IC package (D) has been tested and has demonstrated an ability to be reflow soldered to a PCB substrate. The solder reflow profile describes the expected maximum heat exposure of components during the solder reflow process of product on a PCB. Temperature is measured on top of component. The component should be limited to a maximum of three passes through this solder reflow profile. Table 1. TSL230RD Solder Reflow Profile PARAMETER Average temperature gradient in preheating Soak time Time above 217°C Time above 230°C Time above Tpeak −10°C Peak temperature in reflow Temperature gradient in cooling tsoak t1 t2 t3 Tpeak REFERENCE TSL230RD 2.5°C/sec 2 to 3 minutes Max 60 sec Max 50 sec Max 10 sec 260° C (−0°C/+5°C) Max −5°C/sec Tpeak Not to scale — for reference only T3 T2 T1 Temperature (5C) Time (sec) tsoak t3 t2 t1 Figure 10. TSL230RD Solder Reflow Profile Graph The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 11 TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 Moisture Sensitivity Optical characteristics of the device can be adversely affected during the soldering process by the release and vaporization of moisture that has been previously absorbed into the package molding compound. To prevent these adverse conditions, all devices shipped in carrier tape have been pre-baked and shipped in a sealed moisture-barrier bag. No further action is necessary if these devices are processed through solder reflow within 24 hours of the seal being broken on the moisture-barrier bag. However, for all devices shipped in tubes or if the seal on the moisture barrier bag has been broken for 24 hours or longer, it is recommended that the following procedures be used to ensure the package molding compound contains the smallest amount of absorbed moisture possible. For devices shipped in tubes: 1. Remove devices from tubes 2. Bake devices for 4 hours, at 90°C 3. After cooling, load devices back into tubes 4. Perform solder reflow within 24 hours after bake Bake only a quantity of devices that can be processed through solder reflow in 24 hours. Devices can be re-baked for 4 hours, at 90°C for a cumulative total of 12 hours (3 bakes for 4 hours at 90°C). For devices shipped in carrier tape: 1. Bake devices for 4 hours, at 90°C in the tape 2. Perform solder reflow within 24 hours after bake Bake only a quantity of devices that can be processed through solder reflow in 24 hours. Devices can be re−baked for 4 hours in tape, at 90°C for a cumulative total of 12 hours (3 bakes for 4 hours at 90°C). Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 12 www.taosinc.com TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 PRODUCTION DATA — information in this document is current at publication date. Products conform to specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard warranty. Production processing does not necessarily include testing of all parameters. LEAD-FREE (Pb-FREE) and GREEN STATEMENT Pb-Free (RoHS) TAOS’ terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material). Important Information and Disclaimer The information provided in this statement represents TAOS’ knowledge and belief as of the date that it is provided. TAOS bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TAOS has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TAOS and TAOS suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. NOTICE Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems. TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK. LUMENOLOGY, TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced Optoelectronic Solutions Incorporated. The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 13 TSL230RD, TSL230ARD, TSL230BRD PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS TAOS054N − OCTOBER 2007 Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 14 www.taosinc.com