TSL235R

r r TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 D High-Resolution Conversion of Light D D D D D D D Intensity to Frequency With No External Components Communicates Directly With a Microcontroller Compact Three-Leaded Clear-Plastic Package Single-Supply Operation Down to 2.7 V Nonlinearity Error Typically 0.2% at 100 kHz Stable 150 ppm/°C Temperature Coefficient Single-Supply Operation RoHS Compliant (−LF Package Only) PACKAGE S SIDELOOKER (FRONT VIEW) PACKAGE SM SURFACE MOUNT SIDELOOKER (FRONT VIEW) 1 GND 2 VDD 3 OUT Description 1 GND 2 VDD 3 OUT The TSL235R light-to-frequency converter combines a silicon photodiode and a current-to-frequency converter on a single monolithic CMOS integrated circuit. Output is a square wave (50% duty cycle) with frequency directly proportional to light intensity (irradiance) on the photodiode. The digital output allows direct interface to a microcontroller or other logic circuitry. The device has been temperature compensated for the ultraviolet-to-visible light range of 320 nm to 700 nm and responds over the light range of 320 nm to 1050 nm. The TSL235R is characterized for operation over the temperature range of − 25°C to 70°C and is supplied in a 3-lead clear plastic side-looker package with an integral lens. When supplied in the lead (Pb) free package, the device is RoHS compliant. Functional Block Diagram Current-to-Frequency Converter Light Photodiode Output Available Options DEVICE TSL235R TSL235R TSL235R TA −25°C to 70°C −25°C to 70°C −25°C to 70°C PACKAGE − LEADS 3-lead Sidelooker 3-lead Sidelooker—Lead (Pb) Free 3-lead Surface-Mount Sidelooker—Lead (Pb) Free PACKAGE DESIGNATOR S S SM ORDERING NUMBER TSL235R TSL235R−LF TSL235RSM−LF Terminal Functions TERMINAL NAME GND OUT VDD NO. 1 3 2 O TYPE DESCRIPTION Power supply ground (substrate). All voltages are referenced to GND. Output frequency. Supply voltage. The LUMENOLOGY r Company Texas Advanced Optoelectronic Solutions Inc. 1001 Klein Road S Suite 300 S Plano, TX 75074 S (972) 673-0759 r www.taosinc.com 1 r Copyright E 2007, TAOS Inc. TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 25°C to 70°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 25°C to 85°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds (S Package) . . . . . . . . . . . . . . . . . . . . 260°C Reflow solder, in accordance with J-STD-020C or J-STD-020D (SM Package) . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values are with respect to GND. Recommended Operating Conditions MIN Supply voltage, VDD Operating free-air temperature range, TA 2.7 − 25 NOM 5 MAX 5.5 70 UNIT V °C Electrical Characteristics at VDD = 5 V, TA = 25°C (unless otherwise noted) PARAMETER VOH VOL IDD High-level output voltage Low-level output voltage Supply current Full-scale frequency‡ Temperature coefficient of output frequency kSVS ‡ TEST CONDITIONS IOH = − 4 mA IOL = 4 mA MIN 4 TYP 4.5 0.25 2 MAX 0.4 3 UNIT V V mA kHz ppm/°C %/ V 500 Wavelength < 700nm VDD = 5 V ±10% ± 150 ± 0.5 Supply-voltage sensitivity Full-scale frequency is the maximum operating frequency of the device without saturation. Operating Characteristics at VDD = 5 V, TA = 25°C PARAMETER fO Output frequency Nonlinearity § N li it Step response to full-scale step input ‡ § TEST CONDITIONS Ee = 430 μW/cm2, λp = 635 nm Ee = 0 μW/cm2 fO = 0 kHz to 10 kHz fO = 0 kHz to 100 kHz MIN 200 TYP 250 0.4 ± 0.1% ± 0.2% MAX 300 10 UNIT kHz Hz %F.S. %F.S. 1 pulse of new frequency plus 1 μs Full-scale frequency is the maximum operating frequency of the device without saturation. Nonlinearity is defined as the deviation of fO from a straight line between zero and full scale, expressed as a percent of full scale. Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 2 www.taosinc.com TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 TYPICAL CHARACTERISTICS OUTPUT FREQUENCY vs IRRADIANCE 1000 VDD = 5 V λp = 635 nm TA = 25°C Normalized Responsivity 1.2 PHOTODIODE SPECTRAL RESPONSIVITY fO — Output Frequency — kHz 100 1.0 10 0.8 1 0.6 0.1 0.4 0.01 0.2 0.001 0.001 0.01 0.1 1 10 10 0 1k 0 300 400 500 Ee − Irradiance − μW/cm2 600 700 800 900 λ − Wavelength − nm 1000 1100 Figure 1 DARK FREQUENCY vs TEMPERATURE 1.2 VDD = 5 V Ee = 0 Figure 2 TEMPERATURE COEFFICIENT OF OUTPUT FREQUENCY vs WAVELENGTH OF INCIDENT LIGHT 7000 6000 5000 4000 3000 2000 1000 0 300 VDD = 5 V 1 fO(dark) — Dark Frequency — Hz 0.8 0.6 0.4 0.2 0 −25 0 25 50 TA − Temperature − °C 75 Temperature Coefficient of Output Frequency — ppm/5C 400 500 600 700 800 900 1000 λ − Wavelength of Incident Light − nm Figure 3 Figure 4 The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 3 TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 TYPICAL CHARACTERISTICS OUTPUT FREQUENCY vs SUPPLY VOLTAGE 1.010 TA = 25°C fO = 250 kHz 1.005 Normalized Output Frequency 1.000 0.995 0.990 0.985 0.980 2.5 3 3.5 4 4.5 5 5.5 VDD − Supply Voltage − V Figure 5 Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 4 www.taosinc.com TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 APPLICATION INFORMATION Power-supply considerations Power-supply lines must be decoupled by a 0.01-μF to 0.1-μF capacitor with short leads placed close to the TSL235R (Figure 6). Output interface The output of the device is designed to drive a standard TTL or CMOS logic input over short distances. If lines greater than 12 inches are used on the output, a buffer or line driver is recommended. Measuring the frequency The choice of interface and measurement technique depends on the desired resolution and data-acquisition rate. For maximum data-acquisition rate, period-measurement techniques are used. Period measurement requires the use of a fast reference clock with available resolution directly related to reference-clock rate. The technique is employed to measure rapidly varying light levels or to make a fast measurement of a constant light source. Maximum resolution and accuracy may be obtained using frequency-measurement, pulse-accumulation, or integration techniques. Frequency measurements provide the added benefit of averaging out random- or high-frequency variations (jitter) resulting from noise in the light signal. Resolution is limited mainly by available counter registers and allowable measurement time. Frequency measurement is well suited for slowly varying or constant light levels and for reading average light levels over short periods of time. Integration, the accumulation of pulses over a very long period of time, can be used to measure exposure — the amount of light present in an area over a given time period. VDD 2 0.1 μF TSL235R 3 Timer / Port 1 MCU Figure 6. Typical TSL235R Interface to a Microcontroller The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 5 TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 APPLICATION INFORMATION PCB Pad Layout Suggested PCB pad layout guidelines for the SM surface mount package are shown in Figure 7. 1.0 1.0 1.0 3.2 1.0 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. 1.0 Figure 7. Suggested SM Package PCB Layout Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 6 www.taosinc.com TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 MECHANICAL DATA The device is supplied in a clear plastic three-lead through-hole sidelooker package (S). PACKAGE S TOP VIEW 4.60 PLASTIC SINGLE-IN-LINE SIDE-LOOKER PACKAGE 2.60 R 0.90 1.64 FRONT VIEW 2.30 1.80 SIDE VIEW 0.15 Note B 1 4.60 1.56 0.42 14.86 + 0.50 Pb 2y2 0.47 TYP Lead Free Available 0.42 NOTES: A. All linear dimensions are in millimeters; tolerance is ± 0.25 mm unless otherwise stated. B. Dimension is to center of lens arc, which is located below the package face. C. The integrated photodiode active area is typically 0.92 mm2 in size and is located in the center of the lens and 0.97 mm below the top of the lens surface. D. Index of refraction of clear plastic is 1.55. E. Lead finish for TSL235R: solder dipped, 63% Sn/37% Pb. Lead finish for TSL235R−LF: solder dipped, 100% Sn. F. This drawing is subject to change without notice. Figure 8. Package S — Single-In-Line Side-Looker Package Configuration The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 7 TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 MECHANICAL DATA PACKAGE SM TOP VIEW 4.60 PLASTIC SURFACE MOUNT SIDE-LOOKER PACKAGE 2.60 R 0.90 1.64 FRONT VIEW 2.30 SIDE VIEW 0.15 Note B 1.80 4.60 0.62 + 0.10 1.97 2.59 1.00 0.42 0.62 +0.10 −0.15 5.73 + 0.50 2y2 NOTES: A. B. C. D. E. F. Pb 0.47 TYP Lead Free 0.42 All linear dimensions are in millimeters; tolerance is ± 0.25 mm unless otherwise stated. Dimension is to center of lens arc, which is located below the package face. The integrated photodiode active area is typically located in the center of the lens and 0.97 mm below the top of the lens surface. Index of refraction of clear plastic is 1.55. Lead finish for TSL235RSM−LF: solder dipped, 100% Sn. This drawing is subject to change without notice. Figure 9. Package SM — Surface Mount Side-Looker Package Configuration Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 8 www.taosinc.com TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 PRODUCTION DATA — information in this document is current at publication date. Products conform to specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard warranty. Production processing does not necessarily include testing of all parameters. LEAD-FREE (Pb-FREE) and GREEN STATEMENT Pb-Free (RoHS) TAOS’ terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material). Important Information and Disclaimer The information provided in this statement represents TAOS’ knowledge and belief as of the date that it is provided. TAOS bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TAOS has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TAOS and TAOS suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. NOTICE Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems. TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK. LUMENOLOGY, TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced Optoelectronic Solutions Incorporated. The LUMENOLOGY r Company r r Copyright E 2007, TAOS Inc. www.taosinc.com 9 TSL235R LIGHT-TO-FREQUENCY CONVERTER TAOS038E −SEPTEMBER 2007 Copyright E 2007, TAOS Inc. r r The LUMENOLOGY r Company 10 www.taosinc.com