Film Capacitors
Metallized Polypropylene Film Capacitors (MKP)
Series/Type:
B32671L ... B32672L
Date:
March 2017
© EPCOS AG 2017. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
EPCOS AG is a TDK Group Company.
Metallized polypropylene film capacitors (MKP)
B32671L ... B32672L
High V AC, high temperature (wound)
Typical applications
Electronic ballasts (resonant circuits)
SMPS
High-frequency AC loads
Pulse circuits
Dimensional drawing
Climatic
Max. operating temperature: 125 °C
Climatic category (IEC 60068-1): 55/110/56
Construction
Dielectric: metallized polypropylene (PP)
Wound capacitor technology
Plastic case (UL 94 V-0)
Epoxy resin sealing
Dimensions in mm
Features
Very high AC voltages for all frequency
ranges
Very small dimensions
High peak voltage for short time periods
High peak current
High pulse withstand capability
RoHS-compatible
Halogen-free capacitors available on request
Lead spacing
±0.4
10
15
Terminals
Parallel wire leads, lead-free tinned
Special lead lengths available on request
Marking
Manufacturer's logo
lot number, series number
Rated capacitance (coded)
Capacitance tolerance (code letter)
Rated voltage
Date of manufacture (coded)
Delivery mode
Bulk (untaped)
Taped (Ammo pack or reel)
For notes on taping, refer to chapter "Taping and packing“.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 39
Lead diameter Type
d1 ±0.05
0.6
B32671L
0.8
B32672L
B32671L ... B32672L
High V AC, high temperature (wound)
Overview of available types
Lead spacing 10 mm
15 mm
Type
B32671L
B32672L
Page
4
6
VRMS (V AC)
200 250 250 500 600 700 160 200 250 250 500 600 700 900
VR (V DC)
400 630 1000 1000 1600 2000 250 450 630 1000 1300 1600 2000 2000
CR (nF)
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
33
47
56
68
100
150
220
330
390
470
680
1000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 39
B32671L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 10 mm)
VRMS
VR
f ≤1 kHz
V AC
200
250
250
500
CR
V DC nF
400 22
33
47
68
100
630 15
22
33
47
56
1000
4.7
6.8
10
15
22
1000
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
Max. dimensions Ordering code
w×h×l
(composition see
below)
mm
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
B32671L4223+***
B32671L4333+***
B32671L4473+***
B32671L4683+***
B32671L4104+***
B32671L6153+***
B32671L6223+***
B32671L6333+***
B32671L6473+***
B32671L6563+***
B32671L9472+***
B32671L9682+***
B32671L9103+***
B32671L9153+***
B32671L9223+***
B32671L0332+***
B32671L0392+***
B32671L0472+***
B32671L0562+***
B32671L0622+***
B32671L0682+***
B32671L0822+***
B32671L0103+***
B32671L0123+***
Straight
terminals,
Ammo
pack
pcs./MOQ
4000
4000
3320
3320
2720
4000
3320
3320
2720
2720
4000
4000
3320
3320
2720
4000
4000
4000
3320
3320
3320
2720
2720
2720
Straight
Straight
terminals, terminals,
Reel
Untaped
pcs./MOQ
6800
6800
5200
5200
4400
6800
5200
5200
4400
4400
6800
6800
5200
5200
4400
6800
6800
6800
5200
5200
5200
4400
4400
4400
pcs./MOQ
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Straight terminals, Ammo pack
189 = Straight terminals, Reel
240 = Crimped down to lead spacing 7.5 mm,
Ammo pack
140 = Crimped down to lead spacing 7.5 mm,
Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)
Page 4 of 39
B32671L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 10 mm)
VRMS
VR
f ≤1 kHz
V AC
600
700
CR
V DC nF
1600
1.2
1.5
2.2
2.7
3.3
3.9
4.7
2000
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
Max. dimensions Ordering code
w×h×l
(composition see
below)
mm
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
B32671L1122+***
B32671L1152+***
B32671L1222+***
B32671L1272+***
B32671L1332+***
B32671L1392+***
B32671L1472+***
B32671L8102+***
B32671L8122+***
B32671L8152+***
B32671L8222+***
B32671L8272+***
B32671L8332+***
B32671L8392+***
B32671L8472+***
Straight
terminals,
Ammo
pack
pcs./MOQ
4000
4000
3320
3320
2720
2720
2720
4000
4000
4000
3320
3320
3320
2720
2720
Straight
Straight
terminals, terminals,
Reel
Untaped
pcs./MOQ
6800
6800
5200
5200
4400
4400
4400
6800
6800
6800
5200
5200
5200
4400
4400
pcs./MOQ
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Straight terminals, Ammo pack
189 = Straight terminals, Reel
240 = Crimped down to lead spacing 7.5 mm,
Ammo pack
140 = Crimped down to lead spacing 7.5 mm,
Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)
Page 5 of 39
B32672L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 15 mm)
VRMS
VR
f ≤1 kHz
V AC
160
200
250
CR
V DC nF
250 150
220
330
470
680
1000
450
68
100
150
220
330
470
680
630
33
47
68
100
150
220
390
Max. dimensions
w×h×l
mm
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.0 × 14.0 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
Ordering code
(composition see
below)
B32672L2154+***
B32672L2224+***
B32672L2334+***
B32672L2474+***
B32672L2684+***
B32672L2105+***
B32672L4683+***
B32672L4104+***
B32672L4154+***
B32672L4224+***
B32672L4334+***
B32672L4474+***
B32672L4684+***
B32672L6333+***
B32672L6473+***
B32672L6683+***
B32672L6104+***
B32672L6154+***
B32672L6224+***
B32672L6394+***
Straight
terminals,
Ammo
pack
pcs./MOQ
4680
3840
3320
2720
2560
4680
4680
3840
3320
2920
2560
4680
4680
3840
3320
2720
2560
Straight
terminals,
Reel
pcs./
MOQ
5200
4400
3600
2800
2800
2200
5200
5200
4400
3600
3000
2800
2200
5200
5200
4400
3600
2800
2800
2200
Straight
terminals,
Untaped
pcs./
MOQ
4000
4000
4000
2000
2000
1200
4000
4000
4000
4000
2000
2000
1200
4000
4000
4000
4000
2000
2000
1200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Straight terminals, Ammo pack
189 = Straight terminals, Reel
255 = Crimped down to lead spacing 7.5 mm,
Ammo pack
155 = Crimped down to lead spacing 7.5 mm,
Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)
Page 6 of 39
B32672L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 15 mm)
VRMS
VR
f ≤1 kHz
V AC
250
500
600
CR
V DC nF
1000
10
15
22
33
47
68
100
150
1300
6.8
10
22
33
47
68
1600
6.2
6.8
8.2
10
12
15
22
33
47
Max. dimensions
w×h×l
mm
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
6.0 × 11.0 × 18.0
6.0 × 12.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
Ordering code
(composition see
below)
B32672L0103+***
B32672L0153+***
B32672L0223+***
B32672L0333+***
B32672L0473+***
B32672L0683+***
B32672L0104+***
B32672L0154+***
B32672L7682+***
B32672L7103+***
B32672L7223+***
B32672L7333+***
B32672L7473+***
B32672L7683+***
B32672L1622+***
B32672L1682+***
B32672L1822+***
B32672L1103+***
B32672L1123+***
B32672L1153+***
B32672L1223+***
B32672L1333+***
B32672L1473+***
Straight
terminals,
Ammo
pack
pcs./MOQ
4680
4680
4680
3840
3320
2720
2560
4680
4680
3320
2720
2560
4680
4680
3840
3840
3840
3320
2720
2560
Straight
terminals,
Reel
pcs./
MOQ
5200
5200
5200
4400
3600
2800
2800
2200
5200
5200
3600
2800
2800
2200
5200
5200
4400
4400
4400
3600
2800
2800
2200
Straight
terminals,
Untaped
pcs./
MOQ
4000
4000
4000
4000
4000
2000
2000
1200
4000
4000
4000
2000
2000
1200
4000
4000
4000
4000
4000
4000
2000
2000
1200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Straight terminals, Ammo pack
189 = Straight terminals, Reel
255 = Crimped down to lead spacing 7.5 mm,
Ammo pack
155 = Crimped down to lead spacing 7.5 mm,
Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)
Page 7 of 39
B32672L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 15 mm)
VRMS
VR
f ≤1 kHz
V AC
700
CR
Max. dimensions
w×h×l
Ordering code
(composition see
below)
mm
V DC nF
2000
1.0 5.0 × 10.5 × 18.0 B32672L8102+***
1.2 5.0 × 10.5 × 18.0 B32672L8122+***
1.5 5.0 × 10.5 × 18.0 B32672L8152+***
2.2 5.0 × 10.5 × 18.0 B32672L8222+***
2.7 5.0 × 10.5 × 18.0 B32672L8272+***
3.3 5.0 × 10.5 × 18.0 B32672L8332+***
3.9 5.0 × 10.5 × 18.0 B32672L8392+***
4.7 5.0 × 10.5 × 18.0 B32672L8472+***
5.6 6.0 × 11.0 × 18.0 B32672L8562+***
6.2 6.0 × 11.0 × 18.0 B32672L8622+***
6.8 6.0 × 11.0 × 18.0 B32672L8682+***
8.2 6.0 × 12.0 × 18.0 B32672L8822+***
10
7.0 × 12.5 × 18.0 B32672L8103+***
12
8.5 × 14.5 × 18.0 B32672L8123+***
15
8.5 × 14.5 × 18.0 B32672L8153+***
22
9.0 × 17.5 × 18.0 B32672L8223+***
33
11.0 × 18.5 × 18.0 B32672L8333+***
Straight
terminals,
Ammo
pack
pcs./MOQ
4680
4680
4680
4680
4680
4680
4680
4680
3840
3840
3840
3840
3320
2720
2720
2560
Straight
terminals,
Reel
pcs./
MOQ
5200
5200
5200
5200
5200
5200
5200
5200
4400
4400
4400
4400
3600
2800
2800
2800
2200
Straight
terminals,
Untaped
pcs./
MOQ
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
2000
2000
2000
1200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Straight terminals, Ammo pack
189 = Straight terminals, Reel
255 = Crimped down to lead spacing 7.5 mm,
Ammo pack
155 = Crimped down to lead spacing 7.5 mm,
Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)
Page 8 of 39
B32672L
High V AC, high temperature (wound)
Ordering codes and packing units (lead spacing 15 mm)
VRMS
VR
f ≤1 kHz
V AC
900
CR
V DC nF
2000
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
Max. dimensions
w×h×l
mm
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.0 × 14.0 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
11.0 × 18.5 × 18.0
11.0 × 18.5 × 18.0
Ordering code
(composition see
below)
B32672L9102+***
B32672L9122+***
B32672L9152+***
B32672L9222+***
B32672L9272+***
B32672L9332+***
B32672L9392+***
B32672L9472+***
B32672L9562+***
B32672L9622+***
B32672L9682K***
Straight
terminals,
Ammo
pack
pcs./MOQ
4680
3840
3840
3320
2920
2720
2560
2560
Straight
terminals,
Reel
pcs./
MOQ
5200
4400
4400
3600
3000
2800
2800
2800
2200
2200
2200
Straight
terminals,
Untaped
pcs./
MOQ
4000
4000
4000
4000
2000
2000
2000
2000
1200
1200
1200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerances on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Straight terminals, Ammo pack
189 = Straight terminals, Reel
255 = Crimped down to lead spacing 7.5 mm,
Ammo pack
155 = Crimped down to lead spacing 7.5 mm,
Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)
Page 9 of 39
B32671L ... B32672L
High V AC, high temperature (wound)
Technical data
Reference standard: IEC 60384-16. All data given at T = 20 °C, otherwise is specified.
Operating temperature
range
Max. operating temperature Top,max
Upper category temperature Tmax
Lower category temperature Tmin
Rated temperature TR
Dissipation factor tan δ
(in 10-3) at 20 °C
(upper limit values)
at
Insulation resistance Rins
or time constant
τ = CR Rins at 20 °C,
rel. humidity ≤ 65%
(minimum as-delivered
values)
DC test voltage
≤27 nF 27 nF< CR ≤0.1 μF 0.1 μF < CR ≤1 μF
0.8
1 kHz 0.8
10 kHz 1.0
1.0
100 kHz 2.0
3.0
100 GΩ (CR ≤ 0.33 μF)
30000 s (CR > 0.33 μF)
1.6 VR, 2 s
Top (°C)
DC voltage derating
Category voltage VC
(continuous operation
Top ≤ 85
VC = VR
with VDC or VAC at f ≤1 kHz) 85 10%
> 4 upper limit values
< 1500 MΩ
B32671L ... B32672L
High V AC, high temperature (wound)
Pulse handling capability
"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal
voltages, expressed in V/μs.
"k0" represents the maximum permissible pulse characteristic of the waveform applied to the
capacitor, expressed in V2/μs.
Note:
The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the
capacitor. These parameters are given for isolated pulses in such a way that the heat generated
by one pulse will be completely dissipated before applying the next pulse. For a train of pulses,
please refer to the curves of permissible AC voltage-current versus frequency.
dV/dt values
Lead spacing
Type
VRMS (V AC)
VR (V DC)
CR (nF)
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
33
47
56
68
100
10 mm
B32671L
200
250
400
630
dV/dt in V/μs
540
400
540
400
540
400
540
540
400
400
Please read Cautions and warnings and
Important notes at the end of this document.
1000
500
1000
810
810
810
810
810
Page 11 of 39
4700
4300
3800
3400
3200
3100
2700
2500
2300
600
1600
6000
5600
5200
5000
4700
4500
4000
700
2000
11000
10000
9500
9000
8600
8500
8200
8000
B32671L ... B32672L
High V AC, high temperature (wound)
dV/dt values
Lead spacing 15 mm
Type
B32672L
VRMS (V AC)
160
200
VR (V DC)
250
450
CR (nF)
dV/dt in V/μs
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
33
47
56
68
200
100
200
150
170
200
220
170
200
330
170
200
390
470
170
200
680
170
200
1000
170
Please read Cautions and warnings and
Important notes at the end of this document.
630
250
1000
500
1300
600
1600
700
2000
900
2000
300
300
300
300
300
300
300
445
445
445
445
445
445
445
445
1000
1000
1000
1000
1000
1000
3600
3500
3100
2800
2600
2300
2000
1700
1400
10000
9400
9000
7500
7100
6800
6000
5500
5000
4700
4500
4200
3900
3600
3300
2900
2300
15000
14100
13500
11000
10600
10000
9000
8200
7500
7000
6700
Page 12 of 39
B32671L ... B32672L
High V AC, high temperature (wound)
k0 values
Lead spacing 10 mm
Type
B32671L
VRMS (V AC)
200
VR (V DC)
400
CR (nF)
k0 in V2/μs
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
150000
33
150000
47
150000
56
68
150000
100
150000
250
630
1000
200000
200000
200000
200000
200000
400000
400000
400000
400000
400000
Please read Cautions and warnings and
Important notes at the end of this document.
500
1000
9400000
8600000
8200000
7600000
6800000
6200000
5400000
5000000
4600000
Page 13 of 39
600
1600
14400000
14000000
13800000
13600000
13300000
13100000
12000000
700
2000
25000000
23000000
22500000
22000000
21500000
21000000
20900000
20800000
B32671L ... B32672L
High V AC, high temperature (wound)
k0 values
Lead spacing
Type
VRMS (V AC)
VR (V DC)
CR (nF)
1.0
1.2
1.5
2.2
2.7
3.3
3.9
4.7
5.6
6.2
6.8
8.2
10
12
15
22
33
47
56
68
100
150
220
330
390
470
680
1000
15 mm
B32672L
160
200
250
450
k0 in V2/μs
120000
120000
100000 120000
100000 120000
100000 120000
100000 120000
100000
100000
Please read Cautions and warnings and
Important notes at the end of this document.
250
630
1000
500000
500000
500000
500000
500000
500000
500000
1000000
1000000
1000000
1000000
1000000
1000000
1000000
1000000
500
1300
700
2000
900
2000
20300000
19600000
19200000
18600000
18200000
18000000
16800000
15800000
13100000
11520000 12700000
3000000 11200000 12300000
9920000 11800000
3000000 8960000 11100000
8320000 10600000
7360000 10400000
3000000 6400000 9300000
3000000 5440000 9000000
3000000 4480000
3000000
30000000
29400000
28000000
27500000
27300000
27000000
25200000
23500000
19500000
19000000
18400000
Page 14 of 39
600
1600
B32671L ... B32672L
High V AC, high temperature (wound)
Impedance Z versus frequency f (typical values)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 39
B32671L
High V AC, high temperature (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 10 mm
400 V DC/200 V AC
630 V DC/250 V AC
1000 V DC/250 V AC
1000 V DC/500 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 39
B32671L
High V AC, high temperature (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 10 mm
1600 V DC/600 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
2000 V DC/700 V AC
Page 17 of 39
B32672L
High V AC, high temperature (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 15 mm
250 V DC/160 V AC
450 V DC/200 V AC
630 V DC/250 V AC
1000 V DC/250 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 18 of 39
B32672L
High V AC, high temperature (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 15 mm
1300 V DC/500 V AC
1600 V DC/600 V AC
2000 V DC/700 V AC
2000 V DC/900 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 19 of 39
B32671L
High V AC, high temperature (wound)
Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 10 mm
400 V DC/200 V AC
630 V DC/250 V AC
1000 V DC/250 V AC
1000 V DC/500 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 20 of 39
B32671L
High V AC, high temperature (wound)
Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 10 mm
1600 V DC/600 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
2000 V DC/700 V AC
Page 21 of 39
B32672L
High V AC, high temperature (wound)
Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 15 mm
250 V DC/160 V AC
450 V DC/200 V AC
630 V DC/250 V AC
1000 V DC/250 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 22 of 39
B32672L
High V AC, high temperature (wound)
Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 15 mm
1300 V DC/500 V AC
1600 V DC/600 V AC
2000 V DC/700 V AC
2000 V DC/900 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 23 of 39
B32671L ... B32672L
High V AC, high temperature (wound)
Maximum AC voltage (VRMS), current (IRMS) vs. frequency and temperature for TA > 100 ºC
The graphs described in the previous section for the permissible AC voltage (VRMS) or current
(IRMS) vs. frequency are given for a maximum ambient temperature TA ≤100 ºC. In case of higher
ambient temperatures (TA), the self-heating (ΔT) of the component must be reduced to avoid that
temperature of the component (Top= TA + ΔT) reaches values above maximum operating
temperature.The factor FT shall be applied in the following way:
And FT is given by the following curve:
Please read Cautions and warnings and
Important notes at the end of this document.
Page 24 of 39
B32671L ... B32672L
High V AC, high temperature (wound)
Operation at overvoltages during heating and ignition of lamps (TA ≤40 °C)
In lighting applications, the capacitors can be subjected to overvoltages during the heating and ignition periods. An overvoltage occurs when the operation voltage exceeds the permissible
AC voltage at the resonant frequency fr.
For a repetitive application of on/off switching pulses (as for example in the life tests applied by
electronic ballast manufacturers), limits have to be imposed on the time periods under overvoltage and on the duty cycle, in order to keep the capacitance value within the required margins:
The overvoltage time tOV should be less than 1 sec.
The K0 calculated in the overvoltage period (see general technical information) shall be lower
than the maximum K0 provided.
The maximum duty cycle of the overvoltage is given by
where VRMS,ov is the RMS voltage during period tOV
and VRMS is the permissible AC voltage for continuous operation at the resonant frequency fr
(given by the “permissible AC voltage versus frequency f” graphics in theprevious pages).
The drift of capacitance depends on the Vpp attained, and the total time under overvoltage,
which is calculated in hours as follows:
(Ni tOV) / 3600
where Ni is the number of overvoltage impulses and tOV is expressed in seconds.
The maximum drift of capacitance as a function of both parameters is provided graphically in the
following pages.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 25 of 39
B32671L
High V AC, high temperature (wound)
Estimation of the maximum drift of capacitance value in function of the number of total
hours overvoltage
Lead spacing 10 mm
500 V AC/1000 V DC
Please read Cautions and warnings and
Important notes at the end of this document.
600 V AC/1600 V DC
Page 26 of 39
B32672L
High V AC, high temperature (wound)
Estimation of the maximum drift of capacitance value in function of the number of total
hours overvoltage
Lead spacing 15 mm
600 V AC/1600 V DC
Please read Cautions and warnings and
Important notes at the end of this document.
700 V AC/2000 V DC
Page 27 of 39
B32671L ... B32672L
High V AC, high temperature (wound)
Testing and Standards
Test
Reference
Conditions of test
Performance requirements
Electrical
Parameters
IEC 60384-16
Within specified limits
Robustness
of terminations
IEC 60068-2-21
Voltage proof, 1.6 VR, 1 minute
Insulation resistance, RINS
Capacitance, C
Dissipation factor, tan δ
Tensile strength (test Ua1)
Tensile
force
Wire diameter
0.5 < d1 ≤ 0.8 mm 10 N
Resistance to IEC 60068-2-20, Solder bath temperature at
test Tb,
260 ± 5 °C, immersion for
soldering
method 1A
10 seconds
heat
Capacitance and tan δ
within specified limits
ΔC/C0 ≤ 2%
Δ tan δ ≤ 0.002
Rapid
change of
temperature
IEC 60384-16
TA = lower category temperature
TB = upper category temperature
Five cycles, duration t = 30 min.
Vibration
IEC 60384-16
Bump
IEC 60384-16
Climatic
sequence
IEC 60384-16
Damp Heat
Steady State
IEC 60384-16
Test Fc: vibration sinusoidal
No visible damage
Displacement: 0.75 mm
Accleration: 98 m/s2
Frequency: 10 Hz ... 500 Hz
Test duration: 3 orthogonal axes,
2 hours each axe
Test Eb: Total 4000 bumps with No visible damage
ΔC/C0 ≤ 2%
390 m/s2 mounted on PCB
Δ
tan δ ≤ 0.002
6 ms duration
RINS ≥ 50% of initial limit
Dry heat Tb / 16 h.
No visible damage
Damp heat cyclic, 1st cycle
ΔC/C0 ≤ 3%
+55 °C / 24h / 95% ... 100% RH Δ tan δ ≤ 0.001
Cold Ta / 2h
RINS ≥ 50% of initial limit
Damp heat cyclic, 5 cycles
+55 °C / 24h / 95% ... 100% RH
Test Ca
No visible damage
40 °C / 93% RH / 56 days
ΔC/C0 ≤ 3%
Δ tan δ ≤ 0.001
RINS ≥ 50% of initial limit
No visible damage
60 °C / 95% RH / 1000 hours
ΔC/C0 ≤ 10%
with VR,DC
Δ tan δ ≤ 0.002
RINS ≥ 50% of initial limit
High
temperature
high humidity
with load
Please read Cautions and warnings and
Important notes at the end of this document.
Page 28 of 39
B32671L ... B32672L
High V AC, high temperature (wound)
Test
Reference
Conditions of test
Endurance
IEC60384-16
85 °C/ 1.25 VR / 2000 hours
Endurance
IEC60384-16
110 °C/ 1.25 VC / 2000 hours
Performance requirements
No visible damage
ΔC/C0 ≤ 5%
Δ tan δ ≤ 0.002
RINS ≥ 50% of initial limit
No visible damage
ΔC/C0 ≤ 10%
Δ tan δ ≤ 0.002
RINS ≥ 50% of initial limit
Mounting guidelines
1
Soldering
1.1
Solderability of leads
The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1.
Before a solderability test is carried out, terminals are subjected to accelerated ageing (to
IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far
higher than the upper category temperature of the capacitors, the terminal wires should be cut off
from the capacitor before the ageing procedure to prevent the solderability being impaired by the
products of any capacitor decomposition that might occur.
Solder bath temperature
235 ±5 °C
Soldering time
2.0 ±0.5 s
Immersion depth
2.0 +0/0.5 mm from capacitor body or seating plane
Evaluation criteria:
Visual inspection
Wetting of wire surface by new solder ≥90%, free-flowing solder
Please read Cautions and warnings and
Important notes at the end of this document.
Page 29 of 39
B32671L ... B32672L
High V AC, high temperature (wound)
1.2
Resistance to soldering heat
Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A.
Conditions:
Series
Solder bath temperature Soldering time
MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C
coated
uncoated (lead spacing > 10 mm)
MFP
MKP (lead spacing > 7.5 mm)
MKT boxed (case 2.5 × 6.5 × 7.2 mm)
MKP (lead spacing ≤ 7.5 mm)
MKT uncoated (lead spacing ≤ 10 mm)
insulated (B32559)
10 ±1 s
5 ±1 s